updated my mac pro early 2011 book now really running hot

Similar Questions

• Mac pro (early 2008) suddenly doesn't recognize RAM

  Model: Mac Pro (early 2008), 2 x Quad Core Intel Xeon 3.2, 20 GB (should have been 24Go - only recently realized that Genius bar replaced RAM they lost with bad spec, so we have to work outside 20 GB for now), NVIDIA GeForce 8800 GT 512 MB, startup disk 500 GB SSD, 1 TB SATA 7200 RPM, 2 TB SATA 72 RPM.

  O/S: Yosemite, 10.10.5 (14F1509) (to date). Waiting for the seeds with Adobe in El Capitan to be ironed out before the upgrade.

  Background: Mac runs slowly, and the fan is constantly on high even if Mac is not that much. Checked, only 16Gb 20 Gb showing, which then deteriorated to 12 and finally 8 GB of RAM.

  Checks / actions so far:

  -C' IS good RAM for this machine, IE 800 MHz DDR2 FB-DIMM, provided by Apple.

  -All the RAM recognized before (he's been there more than a year and the last time I looked, it was see 20 GB, which is what is inside).

  -DIMM is properly matched on boards.

  -Boards are fully seated in the riser.

  N ' had not moved machine or s/w recently updated.

  -Removed and replaced DIMM, which dumped first tips of handling static etc. carefully according to the instructions from Apple. This resulted in reduction of recognized with 12 GB of RAM.

  -Again re-allocation of places 2nd; It resulted that 8 GB being recognized.

  -Same report (8 GB) I look under > memory or under Activity Monitor > memory

  -No obvious problem with DIMMs or connectors; No dust, scratches or crud.

  -Replace the LANDAU and SMC

  Now at the end of the straps with a job to get out (and Lightroom being a bigger dog than usual with only 8 GB of RAM. I read all the posts I can find on this point, can't find anything I did not... Ideas please people?

  The FBDIMM used in these Macs run hot and die. You did probably nothing wrong, and there is none of the extrinsic factors that prevent your RAM from functioning. DIMMs indicate does not are diagnosed properly - they're dead.

  You can buy more if you want to run more.

  Make sure that you buy DIMM modules with the huge heat sinks and Apple has approved the temperature probe, or they will die sooner.

  As a preventive measure, you can use a third-party program to modestly increase the fan speed.

• Install windows on mac pro (early 2008) in other SSDS with RAID card

  Guys, good evening to all the same time.

  I get out of this crazy short, I ask humbly help.

  I explain my problem:

  I have a Mac Pro (early 2008), with RAID CARD MEDIA

  He does not then I "gave" to my mother who must use windows for work.

  I'm out all 4 disks in RAID installed and mounted 2 - SSD OCZ Agility 256 GB.

  one of them is installed OSX Yosemite. on the other hand, I want to install WINDOWS.

  and here the problems begin:

  When I insert the win8.1 to proceed installation standard dvd (EFI not talked since the beginning of 2008), I get, when I have to decide on which disk to install and format windows, does not reveal the installed drives

  After 2 days of tweaking, I was able to understand that this is a problem due to the RAID card installed, I also read that you just remove it and connect the SSD in one of the two doors empty ODDsata (and not in the 4 planned the raid card slots)

  but still does not see the attached HDD / SSD, so keep trying and I think it's a driver problem and I need to install the AHCI driver, now, I'm pretty Nerd, but I still can't get.

  Someone could want explain step by step what I need to do to install this * win on MacPro 8.1 designed for RAID card?

  Thank you so much in advance.

  A welcome message

  Ruggero

  If you remove the card RAID Apple on the Mac, you MUST connect the iPass cable on its location on the motherboard, or all four bays are unusable:

  

  .

• Is it OK to mix 2 GB and 4 GB in an iMacbook Pro (early 2011)?

  Is it OK to mix 2 GB and 4 GB of DDRAM in an iMacbook Pro (early 2011)?

  Yes. Just to note that Macs are picky about the memory and should get only a memory of the place that ensure that proper operation with your Mac. Crucial and OWC/MacSales are places. Working memory that not always match the Apple card do

• Lightroom cc 2015 does not start after the recent update on Mac Pro Yosemite

  After you download the last updated September 27, lightroom does not start on my mac.

  Used to work without problems so far.

  Tried to disconnect the last clouds and again without success.

  Thanks, that worked.

  Now, I have to do the update again hope that will work as well...

  Do you have any idea what caused the problem?

  Concerning

  Christian

  MIT thank wurde

  Hans Christian Behrendt

  2015-09-30 18:07 GMT + 02:00 rpandita [email protected]>:

  Lightroom cc 2015 does not start after that a recent update on Mac Pro Yosemite creates

  by rpandita https://forums.adobe.com/people/rpandita> in * Photoshop

  Lightroom *-see complete discussion

  https://forums.Adobe.com/message/8015642#8015642>

• Mac Pro early 2008 OS 10.6.8 at 10.11 on a new SSD upgrade

  Hi all!

  I want to spend my Mac Pro hard drive to an SSD with a new installation of El Capitan, but I also want to continue to use Adobe CS3 (I can't afford a new version... > _ <).  I read that some people have a lot of problems after upgrading their operating system, even when you use the legacy of Java 6 to CS3.

  Someone at - it good tutorials step by step to install a new OS on a SSD?  I have the adapter for my Mac to use the SSD drive also.  I'm not * that * tech savvy, so I don't want to spoil anything!  :\

  Would it not be possible to keep my current hard drive with Snow Leopard and run Parallels or Fusion for Adobe CS3 on my SSD?  I've never used Parallels or Fusion (preferences?), so where the Snow Leopard operating system to be need?  On a partition on the SSD or can it be on its own hard drive (the one I'm currently using)?

  Also do not know when I improve my OS, how do I tell my Mac to start El Capitan and not Snow Leopard so I keep the older operating system on its own hard drive?  It is system-> startup disk preferences?  Is that how I can go back, if I need to?

  Here are my specs:

  Mac Pro early 2008 (MacPro 3,1)

  Quad-Core Intel Xeon 2.8 Ghz

  16 GB RAM 800 MHz DDR2 FB-DIMM

  HARD drive 500GBx2 (one is currently my Time Machine, I'll use it as a backup of my photos)

  500GB SSD (no not in my Mac still installed)

  4 TB HARD drive (will have Time Machine on half)

  El Capitan would be really slow on my Mac Pro or should I go with the Mavericks or Yosemite?  I'm just trying to extend the life of my Mac as long as possible!

  I'm really sorry for all the questions!  Thank you very much for any help!  ^____^

  ~ Christina ~.

  -Unless you have already "purchased" Mavericks or Yosemite is is not available for download.

  -I just download the installer of El Capitan from the Mac App Store and run it and order that EL Capitan to be installed on the new SSD. You can then by pressing the Option key at startup to choose which version of the OS you want to boot from. You can set either as the default startup in system preferences > startup disk.

  -During installation, you use the configuration wizard to migrate SN drive stuff. YO can also do it later using Migration Assistant but who has created a new used with the migrated data.

  -With 16 GB of RAM and an SSD El Capitan will be fine

• Replacement for trust Mac Pro early 2008

  Hello

  Looking for a replacement for my very reliable and expandable Mac Pro early 2008.  I got it in 2009 after the death of my PC and on the eve of Apple, highlighted the 2009 model.

  Looking for a replacement and do not know whether to go for high spec 27 "iMac or Mac Pro.  Welder instead of videographer professional seriousness.  All I get will be faster than the current Mac Pro despite many improvements over the years.

  Thank you

  Matt

  As an amateur, I think you should seriously consider any movement until the 2009 model or later. Same factor form except the processor and RAM are on a shelf at the bottom of the Cabinet.

  They are faster because of some of the architecture changes, accept more RAM and still have the PCIe slots that allow you to add upgrades.

• Mac Pro early 2008 adding ram problems

  I recently added RAM to my Mac Pro early 2008. The Mac Pro recognizes only 4 of 8 memory locations. I moved the slots and moved the memory and all slots and all the memories are good. No matter where I put them, or what memory I use, the Mac Pro will see 4 of 8. Any suggestions? Yosemite run 10.10.5, trying to fill all 8 locations with 800 mhz 2 GB DDR2 FB - DIMM.

  Ron

  How are new?

  Where have you bought the new?

  All new are identical?

  All the 'old' are the same?

  What is the size of the old and new?

• MAC Pro early 2008 display goes off during execution of CPU

  My Mac Pro screen turns off at random. I have two screens. Most when it goes out when the system processes more than workload, but he died sometimes even its not working any program. Any help would be appreciated.

  Details of the system

  MAC Pro early 2008

  2 2.8 GHz Quad - Core Intel Xeon processor: 8 strands

  32 GB OF RAM

  ATI Radeon HD 3870 - VRAM: 512 MB

  Cinema HD 1920 x 1200

  Cinema HD 1920 x 1200

  Note the time of the next problem. After the reboot, open the Console app in Finder > Applications > utilities and look for entries of the log at the time of the problem. Suspicious message here.

  Also check the fan on the video card. It runs smoothly and free of dust?

• My wife has an i5 to 2.3 GHz MacBook Pro early 2011 and it worked like a slug.  Ran disk utility and verified that the disk needs repair using recovery HD.  What does this lead and what is the risk of losing all the data is there?

  My wife has an i5 to 2.3 GHz MacBook Pro early 2011 and it worked like a slug.  Ran disk utility and verified that the disk needs repair using recovery HD.  What does this lead and what is the risk of losing all the data is there?

  Even if it is very slow, you must make a return upwards before the race "repair disk". The risk of data loss is minimal, but do it anyway: Save and run to repair the disk.

  As for what it implies - most of the time nothing more than simply sitting and waiting to do his thing.

• I want to exchange a larger HDD (Mac Pro early 2009) and at the same time improve Cougar to El Capitan.

  I want to exchange a larger HDD (Mac Pro early 2009) and at the same time improve Cougar to El Capitan. What is the best way to do it?

  I think the best would be a new installation of El Capitan on the new HD and reinstall the applications on the new HD, and then migrate the data and setting for the previous version of OSX. In this way the least unused stuff enters the new OSX version

• Mac Pro early 2009-7950 HIS Itceq Turbo / 3GB

  Hello

  I bought a GPU 7950 HIS Itceq Turbo / 3GB GDDR5. I tried with the Mac Pro early 2009 (10.9.5) and a 4K monitor, but it does not work perfectly.

  The DVI output is good, but the max resolution only 1080 p. If I use with cable MiniDisplay, and view the right side monitor scratches and horizontal 5 seconds noise appears on 60 Hz. The monitor works fine on 30 Hz. I tried SwitchResx app for the best refresh rate, best rate exceeded the 55 Hz, but the horizonte noise not.

  The other problem, the boot music played twice each time, so pluged the DVI. If the MiniDisplay cable was plugged music start playing around and he played with white screen. The only way to start if you connect the cable

  The seller never try it with a 4K monitor, so I do not know is the card works well.

  The 4 K is Acer BX320HK. It works very well with the MacBook Pro late 2013 (10.10.5) with Nvidia GeForce GT 750 M 2048 MB same MiniDisplay-Display cable.

  Is there someone who uses this card with MacPro and 4 k monitor?

  Thank you!

  The specifications of the card say:

  2560 x 1600 per display (DVI Dual-link)

  You use a dual-link cable?

  I can't find the manual so I don't know what input DVI resolution lets you get.

  What version of OSSX on the MacBook Pro? If more Mavericks try upgrade to the same version of OSX, you can do a test on another HDD for testing with installation.

• Yesterday, I downloaded the upgrade to El Capitan in a Mac Pro (early 2008) running Yosemite 10.10.5, and today I can not start the upgrade

  Yesterday, I downloaded the upgrade to El Capitan in a Mac Pro (early 2008) running Yosemite 10.10.5, and today I can not start the upgrade.

  The only option I have found is to click again on the download button, but the circle of download rest bike for a long time and ultimately that nothing happens.

  See if that helps...

  Start with CMD + r or the Option/alt key to boot from the recovery partition & use utility disk from there to repair the disk, and then repair permissions.

• Stop guard my Mac Pro (early 2008) and it is difficult to restart.

  I have a Mac Pro (early 2008) still works after the installation of El Capitan. The problem is that after a few hours he will leave, and to restart, I have to switch off/on power and try to restart several times. Sometimes, the fan runs at full speed. What could be the problem? Help, please!

  Have you blown dust lately?

  It starts better if left to cool for one hour about?

  If get you it to work again to get MacFanControl to see all time & the fan speed may adjust higher if too hot...

  http://www.CrystalIDEA.com/Macs-fan-control

• Updated for mac os x 10.10 now bridge will not download files from my camera

  Updated for mac os x 10.10 now the bridge will not download files from my camera, need help

  Hi rubincz,

  Could you please conform if you have updated to MAC OS X 10.11 or 10.10?

  If this is the latest version of Mac. Please refer Bridge and El Capitan

  Kind regards

  Assani