Use of the recovery of the operating system of the disks on a Lenovo C365 all-in-One

Similar Questions

• As part of the certification NAS RHEL 6 guest operating system is recommended. We see that the STAF Installation fails on RHEL 6. Because of this issue, can we use RHEL 5.7 as guest operating system?

  As part of the certification NAS RHEL 6 guest operating system is recommended. We see that the STAF Installation fails on RHEL 6. There is no rejection of STAF for RHEL 6.

  Because of this issue, can we use RHEL 5.7 as guest operating system? If so, it will lead to problems when VMware Certification?

  Seems to have been solved in WB 3.0.1

• HP 15 Notebook PC TS: Freezing, blue screens and 100% use of the disk.

  I constantly freeze because of my pc is always 100% use of the disk. Due to the use of disk, it causes my laptop to a blue screen, I received the following information from the configuration of the system errors: Bad, kernal error in the data on the page, out of State driver. When the 100% disk usage, I use about 1 mb of space.
  I use a wireless internet connection.
   
  Before these problems have taken place that I had upgraded to windows 10, shortly after the use of disc started to go up more often eventually cause my laptop to blue screen. With the bsod, it says that my operating system could not be found, so I had to go back to windows 8 through factory reset. With my first boot on my factory reset, I was still having the same problem as before, but since then my errors and problems continue to increase.
  I hope to diagnose my problem and get help before it's too late.

  Hi Zinchy,

  Thank you for the update. Yes, you can run a test lying on the hard drive from the BIOS. Here is a link to guide you.  HP Notebook PC - hardware failures (10, 8 Windows) screening  If the hard drive test OK, I'll try the clean install of Windows 10. Please hold me.

• Windows 8 guard slows to grip and 100% use of the disk.

  original title: upgrade to WINDOWS 8 PRO - system crashes - no Resposnive

  I had recently upgraded family basic form win7 Windows pro. My laptop does is VPCEH15EN from Sony. By Download Upgrade Assistant I had updated. The 1st time, my system became dead slow. After reboot, I found that my use of the disk is 100% all the time. With very little knowledge I had killed some of the background process that I know (and also a few random apps) use of disck came dowm. Here begins another problem. Am not able to uninstall, open Task Manager, change some settings etc... Can help. I have 8 GB of ram, processor i3, 64-bit

  Hello

  I had this same problem, my computer laptop lenovo would remain idle for about 15 minutes, then go back, 100% use of the drive, but not the tag to any process.

  It was a scheduled defragmentation task.

  Task Scheduler open-> Microsoft-> Windows-> Defrag

  Disable or delete the task.

  Hope this helps someone else.

  I thought it was drive problem hard as the computer would be useless without restart using the power button.

• Can embed you fonts in a pdf file after that the pdf has been created? I received a PDF of an another designer, made a few minor corrections, and now the printer cannot be used because the original pdf didn't have all fonts embedded. Any ideas?

  Can embed you fonts in a pdf file after that the pdf has been created? I received a PDF of an another designer, made a few minor corrections, and now the printer cannot be used because the original pdf didn't have all fonts embedded. Any ideas?

  Use the Acrobat Pro preflight!

  To incorporate the missing fonts in Acrobat Preflight profile will incorporate the missing fonts in your PDF file assuming that:

  (1) the fonts in question are installed on your system and

  (2) the police themselves is not protected against the incorporation (they can at least see and print incorporation.

  -Dov

• 100% use of the disk in the Task Manager when you use Photoshop CC (8.1-64-bit Windows)

  Hello

  I have been using Adobe CC for a month or two now. I have an Asus laptop with Intel Core i7 (2.4 GHz), 6 GB RAM, 1 TB hard disk space and 64 bit, almost 6 months old. Following apps are installed: Photoshop, Illustrator, InDesign, Audition, Acrobat Pro XI, Premiere Pro and Media Encoder. I recently did an update through Adobe CC for Photoshop and Illustrator, all the others are up to date.

  I think, but I could be wrong, since this update Photoshop is weird on my laptop. When I run Photoshop, my task manager immediately indicates a rate of 100% of my use of the disk. This seems to be off, after it is fully operational, but when I start to edit a file, the use of the disc immediately breaks back to 100%, while the CPU remains below 10%, RAM stays 3, 5-3, 8 GB (only 60% of total capacity) and even the actual read and write speeds of my HARD drive are not particularly high (5-10 MB max). And because of the use of the disk of 100%, Photoshop freezes in an instant and operating it is almost impossible.

  I already uninstalled Photoshop, passed all services and * that could trigger it in Windows 8.1 (Google search for: 8.1 Windows disk use 100%), re-installed Photoshop and I still have the same problem.

  So, I was wondering if there could be a solution to this problem or if anyone else has this problem as well?

  Thanks in advance!

  UPDATE: this error only applies when trying to manipulate, add, change or delete the text. All other functions (unrelated to the text) seem to work fine.

  Check out this help file: troubleshooting fonts | CS6 2014 CC, CC, Photoshop, CS5

  You can also try resetting Photoshop preferences and increasing the amount of ram available to Photoshop, if troubleshooting doesn't help.

• Comparing the use of the data store for the use of the disk on the server virtual computer: Match is not

  I'm a bit confused and could use clarification of a person.

  I'm looking to a virtual machine through the vSphere Client and it has an alert telling me that my free space data store is low. 17.55 free GB of 134,75 GB total capacity. I'm running ESX 4.0 for the host and my VM running Server 2008.

  I'm confused because when I connect to the virtual computer and check the use of disk in my computer, it does not reflect what vSphere tells me. This particlular VM is little used and the use of the disk under windows is very very low. About 20 GB.

  Can someone tell me why these numbers are not matching? I have other virtual machines that are in the same situation.

  Thank you

  Blake

  I think that you may be mixing two things up, the vSphere client will only warn about the data store, the VMFS volume, you have created and presented to ESX. You then create a VMDK file for your Virtual Machine to use. If you assign more than 80% of your data store to a VMDK or several VMDK then the customer will report a warning on its use. WARNING 80% 90% critical even if inside each VMDK file you may be using only a couple of GB.

  If you give a little more detail on the virtual machine and the data store, we should be able to get out.

  Hope this helps,

  Dan

• Can not find the driver of scan to PRINTER ALL-IN-ONE KODAK ESP 5210

  Can not find the driver of scan to PRINTER ALL-IN-ONE KODAK ESP 5210. Device Manager says last driver is installed.

  Moved from feedback

  Original title: scan driver

  Hello Timmy,

  Please take a look at the following link for the driver\firmware for your printer.

  KODAK ESP 5210 All-in-One Printer Firmware - WINDOWS operating systems

  If this is not enough, you may have contact with Kodak support for the same. Thank you.

• How to upgrade the processor in an HP Envy all-in-one computer tilt 27

  AFTER my warranty expires... Can I upgrade the CPU in a computer all in one HP Envy bow 27? Currently, I have an Intel Core i7 - 4765T core @ 2.00 GHz. The BIOS is capable of receiving a faster processor in the future?

  Well, I can confirm you can improve to an Intel Core i7 - 4770T (Haswell) 2.5 GHz Quad Core processor

  http://support.HP.com/us-en/document/c04104098

  Unfortunately HP has not posted a guide step by step disassembly as I'm used to having for laptops. I couldn't find a guide on youtube. All-in-one is a little easier to disassemble that laptops, but not much.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Can I replace the printhead on an HP Photosmart3210 all-in-one?

  Can I replace the printhead on an HP Photosmart3210 all-in-one?

  Well, if you have tried several cleanings then it is really not any other measure - printers need to be served by HP and several years out of warranty. I would not continue to try to use it if there is leakage of ink. Sorry - I regret that you are out of luck with this one.

• I pressed the reset button default values during the installation on Officejet 4620 navigation all in one.

  I pressed the reset button default values during the installation on Officejet 4620 navigation all in one, now I can't connect to my wireless network. My router is a box of phone company that I do not have access to. Any help?

  Oh, sorry.  Make sure the USB cable is NOT connected when you run the software or it will assume that you want a USB installation.  It will ask you which type of installation desired and, of course, choose wireless.

  Later you will be asked to plug a USB cable.  Wait until he asked.

• Lenovo C200 all in one recovery DVDs

  Hello

  Anyone know where I can get the Lenovo C200 all in one Recovery DVD for? Is there a place to download them, or what I have to cross and ring support for Lenovo?

  I'm sorry, but I don't know who.

  Service would be able to tell.

  Kind regards.

• Using Lenovo C540 all-in-one as a second screen

  I recently bought two computers, a laptop Asus desktop Lenovo C540 all-in-One touchscreen, Windows 8 and Windows touch, 8.

  The issue I'm facing is to attempt to use the Lenovo as the 2nd screen to the laptop. Is this possible with an all-in-one device since it is not a stand-alone monitor? If so, how would I go on this subject?

  I tried just to plug in an HDMI cable between the two and go in the options screen 2, but which have resulted in nothing.

  Hi Bushy808,

  Welcome to the Community Forums of Lenovo!

  I checked the C540 details and the HDMI on the back is only for HDMI output

  The unit is has a HDMI to display an external device on its screen.

  

  Best regards

  Solid Cruver

• System Recovery Options - no operating system listed, need to load the drivers, but don't know where to find this (Windows Vista 64-bit)

  It is a gateway M6866 laptop running Windows Vista 64-bit.

  The computer does not start up--gives "BOOTMRG is missing" error at startup.  I'm trying to boot from the 64-bit of Windows Vista recovery disc.  I clicked on the "repair your computer" option, and it shows the computer loading files.  Then the "System Recovery Options" box appears and asks me to select the operating system to fix it.  The problem is that nothing has listed.  It is said that if your OS is not listed click Load Drivers.  I did, but it is said to insert the device installation media, and then click OK to select the driver.  I clicked on OK and then opens a browser window to select the file.

  I don't know which file I'm supposed to select here.  I searched online for an answer, and someone told him to go to the computer manufacturer's website and download the driver for RAID controller.  I tried to go to the site of the bridge to find it, but it doesn't seem to be one for Vista 64-bit.

  Please please help!  I have to at least be able to extract the files to the hard drive before reinstalling windows.

  Hello

  ·        Have you Configure RAID on the system?

  If you have not configured then RAID on the system, I suggest you to disable the RAID/eSATA (SATA improved) in the BIOS. Once you turn off the RAID/eSATA on the system that your basic hard disk should be recognized by the system because it doesn't require any drivers, it will act as an IDE. Once you have disabled the RAID/eSATA then booting into the recovery environment and build the Bootrec and check if the problem is resolved. I suggest you follow the steps mentioned below to rebuild the bootrec.

  Rebuild the BCD store by using the Bootrec.exe tool in the Windows recovery environment. To do this, follow these steps:

  a. get the Vista installation DVD and pop in your drive.

  b. then restart your computer.

  c. press a key when you are prompted.

  d. Select a language, a time, a currency, and a keyboard or another input method, and then hitNext

  e. click on repair your computer

  f. click the operating system you want to repair, and then click Next

  g. in the System Recovery Options dialog box, click command prompt

  h. type bootrec /rebuildbcd and then press the Enter"" key.

  ·        If Bootrec runs successfully, it will present you with the installation of a Windows directory path. To add the entry in the BCD store, type Yes. A confirmation message appears that indicates the entry has been added successfully.

  ·        If Bootrec cannot findany lack of facilities of Windows, you must remove the BCD store, and then you must re-create it. To do this, type the following commands in the order shown below: (remember to press ENTER after each command)
  bcdedit/export C:\BCD_Backup
  Ren c:\boot\bcd BCD.old
  Bootrec /rebuildbcd

  i. restart the computer.

  For more information, see the article mentioned below.

  How to use the Bootrec.exe tool in the Windows recovery environment to troubleshoot and repair startup issues in Windows

  http://support.Microsoft.com/kb/927392

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Use of the disk Windows 8 Pro Hyper-V host to 100%

  Hi all

  I'm puzzled. I have a Windows 7 Pro VM a Windows 8 Pro Hyper-V host. When I start the virtual machine, the use of the disc on the drive that it is installed on goes to 100% (on the host). The entire disk, RAM & CPU usage seems normal on the host. The only symptom on the host is extreme latency when I click on things (!).

  As I said earlier, the host is running Windows 8 Pro. He has three physical disks - an SSD that the operating system is installed, and RAID two arrays totaling 18 to each. He has a physical processor, 6 hearts w/hyper-threading. 32 GB of RAM.

  The virtual machine is the only VM I allocated 16 GB of RAM w/dynamic RAM active I allocated 8 cores to it. The OS is installed on a virtual drive of 500 GB. I hung a second virtual disk of 4 TB (TPG), but it is currently offline. I thought maybe it was the problem, but the use of the disc is always maxed out at present. The only other thing I've tried, it is true that as a long-shot, had to change the location of paging on the other empty disk (on the host). That had no effect, either, and I will probably put it when I can. As I type this, the VM is restarted after installing Hyper-V integration services and an update of Windows (including SP1). This will probably take a while...

  Any thoughts are appreciated!

  Hi Jspartacus,

   

  Please contact Microsoft Community.

  I suggest you post your question in the TechNet forum for more help on
  in this issue. We have a dedicated team with tool in advance and Permission to help
  solve you this problem.

  Follow the link:

  https://social.technet.microsoft.com/Forums/windows/en-US/home?category=w8itpro.

   

   

  Please respond with the State of the question, so that we could help you
  better.

   

  Thank you.