VAIO Duo 13 touchscreen does not well during the charge. Stop charge in battery mode, it's ok.

Similar Questions

• PC does not work with the charger also

  My laptop is hard to give a beep, I know I need to change the battery, but the PC does not work with the charger also

  Original title: laptop Dell Inspiron M5030

  Hello

  "beep" codes normally indicate a hardware problem / failure.

  http://www.Dell.com/support/drivers/us/en/19/ProductSelector

  Go to the Dell website and look at the specifications of your laptop to see what BIOS you have

  Then read this on the 'beep' error codes to try to see what failed:

  http://www.computerhope.com/beep.htm

  http://www.pchell.com/hardware/beepcodes.shtml

  http://pcsupport.about.com/od/nonworkingcomponent/HT/beepcodestb.htm

  If you are unable to determine the hardware problem yourself, contact the manufacturer if under warranty.

  If it is not under warranty, find a good repair shop premises to take.

  See you soon.

• the system configuration not saved during the last stop on the service console error

  Hello

  I m getting this msg of error on the service console

  the system configuration not saved during the last stop on the service console error

  but when I tried to run some commands s troubleshoot mode according to the vmware esxcfg-boot - b, esxcfg-boot - p I got an error message like

  bad interprator usr permission denied

  I guess you follow this KB: http://kb.vmware.com/kb/1002503

  But seems like you have file system errors.

  Try to restart your system in init 1

  Then use fsck command to check your ext3 file system (remember that the file systems are not in use and use the - f option).

  André

• Satellite 200-170-keyboard does not work and the keyboard stops working

  My U200-170 2.5 years, I have the following problem:

  When after the start of the key is opperated the keyboard does not work and the keyboard no longer works (works until the button is pressed) connect a keyboard and a usb mouse. does not work because that device unknown. After Internet received external usb driver work ok. someone at - it an idea to solve this problem.

  Thank you

  AJAN

  Sounds like keyboard problem.
  The operating system uses the pilot to clean keyboard and generally it s not necessary to reinstall the special keyboard driver.
  But one thing is really strange; the yellow exclamation mark in Device Manager

  Eventually it s only a problem of software in such a case, a system restore can be useful...

  Have you checked if the keyboard works in the BIOS?
  Do this!

  If the keyboard does not work in the BIOS, then you will need to replace the internal keyboard with the new.

• I don't like to upgrade Windows XP to Windows 7, because I'm blue screen/crash during the upgrade but the upgrade Windows XP to Windows Vista does not crash during the upgrade!

  I have my computer to another, here my specs:

  Intel Core 2 Duo
  Hard drive 500 GB
  2 GB OF RAM
  DVD player
  Floppy Disk
  The operating system that is running Genuine Windows XP Professional Service Pack 3 and just upgraded Windows 7 (but I know before upgrading Windows 7) and keep the blue screen / Crash when upgrading to Windows 7. but the upgrade Windows XP to Windows Vista is not blue screen/crash during the upgrade.
  Is anyone to upgrade from earlier version of Windows to Windows 7 without crashing and spending fortune?

  Hello

  1 did you change on your computer before this problem?

  2. What is the blue stop screen error message?

  3. When you receive a blue screen during the upgrade?

  You can follow the suggestions and then check.

  Method 1

  Disconnect external devices connected to the computer?

  Method 2

  You can read the article and then check.

  Upgrade Windows XP to Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/help/upgrading-from-Windows-XP-to-Windows-7

  See also:

  Windows 7 Upgrade and Migration Guide

  http://TechNet.Microsoft.com/en-us/library/dd446674 (v = ws.10) .aspx

• Presentation of the action does not work during the Conference

  Hello world

  Here's the background
  -CUCM 10.5
  -Telepresence conductor XC4.1
  -Telepresence Server (VM) 4.2
  -Endpoint: MX300

  I have problem when sharing a presentation at the Conference meeting.
  It doesn't seem to work.
  However, the part of presentation works with success during a normal 2-way call

  I read an article by cisco,
  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/infrastructure/con...

  A field is related to the function of presentation,

  Allow the content
  (Available when the preference of Service has a type of telepresence MCU Conferencing Bridge)
  Whether or not, participants will be able to send video content, such as a presentation.

  Yes: one lane will be reserved on each cascade TelePresence MCU and TelePresence MCU primary specifically for content. Use this setting to enabled WebEx conferences.

  No: the participants will not be able to send content, regardless of the number of ports available on the MCU. Content can always be displayed, since some end points provide content in their main video channel.

  The default value is Yes.

  Need MCU allow sharing feature? or I missed something?

  Thanks in advance

  Sam

  Allow that content is available only when the conference bridge is an MCU and does not apply to a server of telepresence.  The only thing you need to do within the Orchestra, is ensure that "content quality" within the model of the Conference is not set to 'Off', see the top of pg 61 of the guide that you have linked to your post.  Also, make sure you have enabled on the SIP Trunk to driver in CUCM BFCP.

• Other results: preliminary report does not properly during the first run in a loop

  I have an unusual problem with NI TestStand 4.1. I have a loop For and it contains, I have a call from sequence configured as a test of numerical limit. This test is configured to report additional results. All other results are preconditioned test cases. Here's the unusual part: during the first iteration of the loop, the test passes yet additional results for the parameters of all inputs are reported (output parameters are not presented at the time, but more on this later). Spend all additional this test iterations in the loop For and additional results are not reported.

  Regarding output parameters... If a test fails I'm expecting (input and output parameters) results to report. However when I encounter a failure only the additional results that are output parameters are displayed on the test report. Input parameters are not reported.

  If anyone else has experienced this? My expectation was that all additional results would be declared in case of failure. In addition, in the absence of a failure I expect not to see additional results. Thanks in advance!

  The short answer is that the condition of additional results for input is evaluated before it's called the subsequence, so that it uses the value of the previous iteration Step.Result.Numeric (or by default on the first).

  You can see this described as stage 15 in the following link:

  http://zone.NI.com/reference/en-XX/help/370052P-01/tsfundamentals/infotopics/step_execution/

  Kind regards

• Why my PC does not restart during the installation of XP?

  I want to install XP on my desktop and its all good and restarts after having pre installed (when windows copies the files), then the windows loading logo shows, then it starts to install with the control points on the right as follows:

  @ collecting information
  @ dynamic update
  @ preparation facility
  Installation of windows
  O development of installation

  It gets to half way with the installation of windows then restarts whenever it gets to this point. It fails in the regional and Language Options Page. I know I did right, see the link.  http://Windows.Microsoft.com/en-us/Windows-XP/help/Setup/install-Windows-XP I disconnected everything (tv, extra fans, of the additional USB ports for the front and the extra RAM card sound card, graphics card,) and tried again from scratch. Everything is plugged is monitor (on board), power supply, USB mouse with a connector PS/2, USB keyboard, 1 x 1 GB RAM, 1 x 80 GB HD and 1 x DVD player.

  Help!
  Thanks in advance.

  Hello

  -Remove the existing disk partitions before performing a new installation?

  If so, follow these steps to do the same thing:

  a. Insert the Windows XP CD-ROM into your CD-ROM drive.
  b. at the welcome page in the Setup program, press ENTER to continue.
  c. press F8 to accept the license agreement for Windows XP.
  d. If an existing Windows XP installation is detected, you will be asked to fix it. At this point, press ESC (not repair).
  e. the screen now lists all existing partitions and unpartitioned for each hard drive space. Use the cursor/arrow keys to choose a place to create the new partition. Press D to delete an existing partition, or press C to create a new partition in the unpartitioned space.

  If you press D to delete an existing partition, you must then press L (or press ENTER and then press L if it is the system partition) to confirm that you want to delete this partition.

  Repeat this procedure for each of the existing partitions that you want to delete (or move) to create your new partition. When all necessary partitions are deleted, you can then select the remaining unpartitioned space and then press C to create new partitions.

  Note: If you want to create a partition where there is already at least one partition, you must first delete the existing partitions and then create the new partition. Type the size in megabytes (MB) that you want the new partition to be. And then press ENTER. Alternatively, you can just press ENTER to create the partition using all of the available space (for example to create the largest possible partition).

  If you want to install Windows XP, use the arrow keys to select the partition where you want to install Windows XP, and then press ENTER.

  More information on:

  How to install or upgrade to Windows XP

  Differences between a quick format and a regular format during a "clean" of Windows XP installation

  Note: Clean installation/format the partition will erase all the data and install XP

• Clone Stamp does not work during the operation of frequency separation.

  Spacing of the frequencies for the first time by train.  I finished the layer of tone and now works on the texture, but the clone stamp does not work.  I have the linear light value layer and the stamp tool is set to 'active layer '.  The stamp tool is gray in the Middle, as if I were seeing a "high pass sharpening" layer through the center of it.  Tried to save the doc and the reopening, but none here.  Any other ideas?

  -Jeff

  In fact, I restarted Photoshop and it works properly now.  Thanks for the information on how to best to post a question.  I'll remember that next time!

• Records of files does not display during the recording of the converted web page in Internet Explorer

  I have recently installed Windows 10.  I use Acrobat Pro 10.  Now, when you convert a web page in an Acrobat document, when I click on "Save as", most of the shirts in my OneDrive folder do not appear.  This only happens during the conversion of a web page to a pdf Acrobat file.  If I save the web page converted into my office and open it from there, I can see and access all the OneDrive file records.

  Any idea what's going on here?  I tried uninstalling and reinstalling Acrobat but that did not help.  Thank you.

  Acrobat X (10) is not compatible with Windows 10.

• Where can get newspaper of reason behind Manager jaxws soap does not run during the webservice call in weblogic 11 g

  Hi guys,.

  http://docs.Oracle.com/CD/E23943_01/Web.1111/e13734/handlers.htm#WSADV189

  I created SOAP manage by top surround URL and deployment artifacts are generated with build.xml.

  I don't know why managers do not run in the web service call in weblogic 11 g.

  Regarding

  Siddharth Singh

  Solution

  Ant was not generating little class and manager xml file

  I manually copy these files

  Maybe Ant was not generating these files because of this warning

  [jwsc] WARNING: types of annotations without Transformers: [javax.xml.bind.annotation.XmlRootElement, javax.xml.bind.annotation.XmlAccessorType, javax.xml.bind.annotation.XmlType, javax.xml.bind.annota

  n.XmlElement]

  [jwsc] 1 WARNING

  Full journal of ants

  D:\SOAP_JMS>Ant f ant - build - jhand.xml
  BuildFile: Ant - build - jhand.xml
  Trying to replace the old definition of the task clientgen

  Build-service4:
  [jwsc] TJ: processing module/om/sai/buddh/SaiWebService
  [jwsc] The analysis of source files
  [jwsc] The analysis of source files
  [jwsc] 1 TJS files processing for the module/om/sai/buddh/SaiWebService
  [jwsc] TJ: D:\Oracle-ESB-RND\EncrpytionDecriptionWS\src\om\sai\buddh\SaiWebService.java valid.
  [jwsc] Treatment of the web services JAX - WS 1...
  [jwsc] WARNING: types of annotations without Transformers: [javax.xml.bind.annotation.XmlRootElement, javax.xml.bind.annotat
  tion. XmlElement]
  [jwsc] 1 WARNING
  [jwsc] Compilation of 5 source files for C:\Users\si244339\AppData\Local\Temp\_y1j0ng
  [jwsc] Building jar: D:\SOAP_JMS\outputnew\AAJAXHandlerSai1EarResponseQ\om\sai\buddh\SaiWebService.war
  [jwsc] Created JWS deployment outputFile: D:\SOAP_JMS\outputnew\AAJAXHandlerSai1EarResponseQ\om\sai\buddh\SaiWebServic
  [jwsc] [EarFile] Application file: D:\SOAP_JMS\outputnew\AAJAXHandlerSai1EarResponseQ\META-INF\application.xml
  [AntUtil.deleteDir] remove directory C:\Users\si244339\AppData\Local\Temp\_y1j0ng

  BUILD SUCCESSFULLY

• my watch is dead and does not even on the charger

  My Apple Watch is dead. Doesn't react anymore and also on the charger there is no reaction, even after several hours

  Hello

  Try restarting your watch force: hold down the side button and the digital Crown for about 10 seconds, until you see the logo.

  If this does not help, then try to charge your watch for about 2.5 hours, making sure that you follow the instructions from here:

  Check your battery and load your Apple Watch - Apple Support

  After this period, if it has not already restarted automatically, remove it from the charger and:

  -Try to restart it (by pressing the side button until you see the Apple logo).

  -Then try force it restarts again.

  More information:

  If your Apple Watch does not respond or won't turn on - Apple Support

• Rebel T5 does not work using the live view. Live view mode is enabled, but images are not captured.

  Rebel T5 is not capturing images when taking pictures in mode live view.  Live view mode is activated but update automatic and image capture does not work.  Any suggestions?

  troyantonik,

  What lens do you have and have you tried other lenses with your camera to see if they also not auto focus when you press the shutter button halfway?

  Just in case a parameter can be the cause, I recommend you to reset the unit to default settings.  Follow these steps:

  1. Press the MENU key.
  2. [#3 tools] tab.
  3. Select [clear settings].
  4. Select [delete all device settings].
  5. Click [OK].
  6. Select [clear all custom Func.].
  7. Click [OK].
  8. Exit the menu.

  If it is a time sensitive matter, additional support options are available to contact us.

• My computer does not load before the login screen, even in safe mode

  I log on to my account (admin) by entering my password.  Then when I click on login I get the 'Welcome' screen and the circle that just guard spinning.  Nothing ever changes.  This happens both in Mode without failure.  I can sign in the guest account, but every time I try to do anything that requires admin login it freezes again.  Help?

  Hello

  in safe mode does not allow you whatever it is read this information

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  And make sure you only set the CD/DVD drive to be 1st in the boot order to boot from the drive that you have just made

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

• Dell Inspiron 17R 5720 does not work with the charger. Charger is not recognized. No problem with charger.

  My Dell Inspiron 17R 5720 does not recognize charger. And unfortunately my warranty expired 2 months ago.
  It was plugged and work in the morning, but then in the afternoon I noticed he was running on battery only. It does not start without battery (charger just plugged).

  1 this is what I did to debug. Me and my brother, we bought the same computers Dell laptops at the same time a year and a bit ago. That's why a debugging purposes, it was good.
  I took my charger and plugged into his computer. And it works. Certainly not the charger problem I guess. And when I plug the charger my computer, green light is still on the charger. And I have the original charger provided with the laptop.

  2. now, laptop is running on battery only, so that means that this motherboard works. I think so.

  3. the next thing I did was charger disconnected and removed the battery from the laptop. Then I pushed and hold the "Power" button for 45 seconds to pay a royalty to the flea market. Charger plugged in but laptop will not start.

  4. then I booted the laptop on battery, went to the BIOS and check if the charger is recognized in the BIOS. No, it does not recognize charger. So, if this isn't a charger so what else can we?

  5 laptop has no strange smells so I don't know if something happened with the motherboard, but I guess that motherboard is ok because it works battery.

  6. I was thinking of updating the BIOS, but I can't do it, because it will be not be updated then the laptop runs on the battery, it needs to be plugged.

  Now I'm stuck. I don't know what I can do. I'm willing to spend a little more money on it to try to fix.

  If someone had such a problem in the past please let me know what you have done and if it fixed it.
  Or if anyone has any other ideas, I will be happy and appreciated the help.

  Hello and sorry for this late post. Just had this problem... If there is nothing wrong with the AC adapter, it's a software problem.

  Close the laptop... Unplug the AC adapter / CC... Remove the battery... Plug the power adapter... Start the laptop... Go to the control panel... Find and select the Device Manager... Batteries, left click... Uninstall Microsoft AC Adapter, uninstall Microsoft ACPI compatible with battery control method... In fact, uninstall all you can under the batteries, but that should be all there is. It will be re - install when starting... Stop cell phone... Remove the AC adapter / CC... Replace the battery... Plug the power adapter... Start the laptop... Now, everything should be good.