vCenter and using a NAT IP

Similar Questions

• RV082 v4.0.0.07 individuals and access rules NAT problem

  Hello

  I just bought two RV082 to run a 20 computer and office web server 4. I use special NAT to public IPs are mapped on different servers and our monitoring system and it seems to work very well. For each address of individuals using a NAT, I created the following access rules:

  Allow HTTP WAN1 everything [PA]

  Allow SSH WAN1 everything [PA]

  Refuse all WAN1 everything [PA]

  Allow rules are of a higher priority so my experience with other firewalls suggests that they should be applied first blocks access to all ports and ports HTTP and SSH then would be open. What seems to be the case is very disconcerting, with any rules applied Allow refusal rules are removed completely open all ports. If I move the priority of rule Deny it blocks all ports, as expected.

  My question is how can I prevent access to all ports except ports HTTP and SSH with the router in NAT mode specific.

  When an access rule is set on a NAT 1 rule at 1, you want to change the public ip address to the private IP which is mapped to the public ip address.

  Allow to use HTTP WAN1 everything [private address]

  Allow SSH WAN1 everything [private address]

  Refuse all WAN1 everything [private address]

• Create new vCenter and move the ESXi hosts

  Hello

  I created a new vCenter vCenter apparatus using ISO 6.

  The deployment went well and I have all the installation program. I would now like to move hosts our old vCenter to new ESXi.

  I was reading this article to start the moving process.

  When I try to disconnect the host I get the message below

  

  In the article in the link above it is written that it will not affect the State of the virtual machine running on the host.

  If I click on 'Yes' here, it will automatically put the host in maintenance mode?

  I prefer not to do it if I can avoid it because I don't want to have to evacuate all virtual machines running on the esxi host.

  Wouldn't it be better if I disabled it HA first? Then try to move hosts? Or I'm sure to sign-out and the subsequent removal?

  Thank you

  See you soon

  Hello

  You must put your server in maintenance as a first step mode, then unplug and remove the server. It will work.

  If it doesn't work, disable temporary HA and remove your host of the VC.

• VCenter and VMWare essential Kits

  Hello

  I have 3 ESXI 5.5 servers in place and another 9 servers ESXI 5.5 in a second location. All servers have two processors and 128 GB or less RAM.

  Can I buy 4 essential Kits of VMWare and install four separate vcenter instances? Am I allowed to use multiple VMware Essentials Kits in one place?

  Is it possible to install one instance of VCenter for all ESXI 5.5 servers 12 with these licenses or do I need to buy a different set of licenses?

  Thank you

  Can I buy 4 essential Kits of VMWare and install four separate vcenter instances? Am I allowed to use multiple VMware Essentials Kits in one place?

  Unless I'm missing something, you can have how many Kits Essentials desired by site/branch, the limitation is that each vCenter Essentials kit can manage only the 03 (three) hosts.

  Is it possible to install one instance of VCenter for all ESXI 5.5 servers 12 with these licenses or do I need to buy a different set of licenses?

  No, each Kit Essentials can manage only the 03 (three) VMware ESXi ESX. To manage hosts more 03, you will need the Standard vCenter and vSphere ESXi Standard, Enterprise or Enterprise Plus.

  Anyway, there are still other options if you don't want to license more advanced, like Standard vCenter and vSphere, ESXi Standard/Enterprise, see: how your vSphere VMware 5.5 retail and management offices (ROBO) - VMware-Blog of SMB - VMware license items

• vCenter and host communication SSL v3

  Hello

  Can someone tell me why a vCenter Server Windows would communicate with a 5.5 on TCP/443 ESXi host using SSLv3 (in particular)?

  If you search Google for "kb2093354" titled "VMware KB: disable encryption on the server vCenter SSLv3" which seems to be what I want, it is no longer available, does anyone have an updated link to day for her?

  According to the Documentation centre, 443 is the WS-Man/HTTPS port and is a required port, but how to disable support for SSLv3? I don't want to tell browser to vCenter for admin, I mean ESXi host to vCenter

  Thank you

  I can confirm that vCenter 5.5 (U2) communicates with guests (5.5 U2) via SSLv3 only, the reason being vCenter only support SSLv3 in his original SSL Client Hello packet when connecting to an ESXi host:

  

  Note: Taking communication SSL/TLS between agents vCenter and vpxa on hosts always is launched from the process of vpxa.exe of vCenter acting as the Client that connects to port 443 of a host and not the other way around (which caught vCenter protocols supported on port 443 is not relevant).

  ESXi supports TLS1 with SSLv3 for long, and since ESXi 5.5 it comes from the tree of openssl 1.0.1 libraries that support TLS1.1/1.2, which can be confirmed from a host:

  # openssl s_client-connect [insert here the ESXi host name]: 443 < ev/null="" 2=""> 1 | grep 'SSL-Session' - A2

  SSL-Session:

  Protocol: TLSv1.2

  Encryption: AES 256-GCM-SHA384

  I suspect that the configuration changes must be made to the vCenter Java application so that the Client sends a TLS version in the handshake Hello. When I lanuch the Java Control Panel on the vCenter via the command below I can see SSLv3 and TLSv1 are supposed to be enabled, but the negotiation Client Hello sent by vCenter to the SSLv3 Client only:

  Com.sun.deploy.panel.ControlPanel - Xbootclasspath/r: "c:\Program Files VMware vCenter Server - Java Components\lib\deploy.jar" "C:\Program Files\Fichiers VMware vCenter Server - Java Components\bin\javaw.exe"

  
  

  It is probably crashed somewhere in the application and I have not tried to disable SSLv3 here since I do not have a currently available test environment. in any case, it would be well if VMware is completely removed this KB article either open to the public instead of saying:

  You are not allowed to view this article. It may have been moved or the reference is out of date.
  

• Impossible to sort according to size service set and used space in the Vsphere 5 client

  Hello guys,.

  I am unable to sort size set service based and used customer area Vsphere 5 any bug? or any workaround for this?

  1. click on any specific data store

  2. go in the virtual machines tab.
  3. try to not sort coloumn - funded space / used space - no reaction.
  4. also sort all coloumn take very long compared to 4.0.
  Thank you.
  -Nice

  The case of the support city...

  "I found PR for this issue and currently, this fix is moved to vCenter 5.0 release U3. ETA for this version is currently seven 2013. »

• Automatically start vCenter and vms

  Hello

  We have Windows Server 2008 R2 running vCenter 4.1 connected to host computers running ESXi 4.0 Update 1.  Every time we restart the server, the vmware vCenter and vmware vCenter Webservices services start up, they are set to start.  They need to be on the delayed start?  I check the event logs to see what is happening.  Is there a log of vmware that I could look at?

  In addition, we want to implement our virtual machines as the domain controller starts automatically, but I can't find a way to do.

  Thank you

  Mike

  Thank you very much, we are using SQL Express despite 2 virtual machines running SQL Server 2008 :-)  I'm going to the delay value and see.

  If it does not help there are some registry entries, you can make

  http://KB.VMware.com/kb/1007669

  In addition, we vSphere Essentials.  How can I know that if it is configured for high availability and where I see these priorities?

  Essentials does not come with HA.  You can configure your options of start/stop for your guests by going to the configuration of the host tab: start/stop of the VM - properties (upper right corner)

• How can I connect to a virtual machine that uses a NAT map from outside via RDP

  Hi, I'm under workstation 7.11. I have a windows xp virtual machines all use adapter NAT of VMware Workstation for connectivity. I am only able to connect to the VMs with RDP client via the host. If I try to anywhere else, I am unable to connect.

  You can use linked by a bridge instead of NAT?  If this isn't the case, you need to enable Port Forwarding on the VMnet in the virtual network Editor.  FWIW, if you do not enable Port Forwarding I recommend setting up on a VMnet custom as VMnet2 example and assign the NIC of the virtual machine.  This keep the default VMnet8 for an unaltered NAT network.

  Default port for RDP is TCP 3389

• Patching vCenter when Using SQL Server Express

  Hello

  I have a few questions about the correction of vCenter and will use the installation of vCenter Server 4.0 Patch1 as my reference for these issues...

  I use the tech note at http://www.badkey.com/DB/blogsphere.nsf/2/JWIE-7VDPKJ/ $File/PTech_note_vCenter_Server_4.0_Patch1.pdf the process document. This seems to be an official document from VMware, but I can't find anywhere on the VMware Web site. What is the correct process? It is on the VMware web site?

  Backup of the database - the tech note above does not have reference to smaller facilities that run SQL Express. Are there specifications compared to this type of installation? If I upgrade, I think he should see the 'old' database immediately, correct? If I do not use the backup for a reason, is there traps to do this up to-and-operational?

  Thank you

  number1vspherefan.

  If you point the existing of the current DB Server vCenter DSN, and then you perform the upgrade.

  Otherwise, you perform a new installation or an upgrade of old data.

  You can see the list of the DSN in your ODBC Manager.

  André

• vCenter and SQL 2005 Express on the same physical machine

  I'm new on the VMware environment and am a little concerned about my VMware infrastructure and design.  I have 3 boxes physical accommodation 15 virtual servers.  I have a 4th server that hosts the database SQL and vcenter.  I am wondering what are my chances of having vCenter and SQL 2005 express installed on the same box?  That suggest VMware as best practices concerning this configuration?  If this configuration is ok, what are my options to protect myself in case the box with vCenter and the SQL database dies?  Thank you

  VMware sets a limitation to 5 guests and 50 wen invited you use SQL Express. I run it with 6 guests and 48 guests (incl. models) on the same machine as the server vcenter. That's not what I want to keep and we will change to a standard SQL 2005 on a separate server from SQL (which we had with SQL 2000 and before VI3).

  But I didn't have one problem with this configuration, again.

  With both on the same server may lead to a conflict: SQL 2005 requires IIS but vCenter uses ports. So I installed it but disabled.

  I think also that separating the two tracks faster that have it all on the same box.

  AWo

  VCP / vEXPERT 2009

• vCenter and View Manager running together?

  The following questions ask about vCenter and View Manager...

  -& gt; Can I install vCenter in one of my virtual servers?

  -& gt; Their problems using vCenter within a virtual server?

  -& gt; Can vCenter and View Manager be installed on the same system and run together?

  -& gt; View Manager can be installed on one of my virtual servers, once again all the problems?

  Thank you

  Marc

  Yes

  No, it is fully supported by VM

  Yes, but I do not recommend

  Yes. No problems.

  ---

  VMware vExpert 2009

  http://blog.vadmin.ru

• VCenter and VCB

  Hello

  I would like to know, if possible install Vcenter and VCB on the same Windows Server or it is not recommended?

  Thank you

  vCenter and VCB share some components, so it is not recommended.  If you have only one physical machine, I would be set up with VCB and using VC in a virtual machine.  You can run VCB in a virtual machine as well, but then you don't get the san connectivity you get when VCB is physical.  Only method NBD (copy of disk based network) works with vcb in a virtual machine.

  -KjB

• Any available adapter to allow the loading and use all the earphone for iphone 7?

  How can I recharge my Iphone and used my set for Iphone 7 ear piece? When I load my iphone 7, the port of lightning and I can't use the the ear piece. Please notify any available adapter?

  Hello

  Solutions for charging your iPhone using wired headphones also include:

  • IPhone dock
    • If you have a headphone with a 3.5 mm jack, you can charge your iPhone and listen to music at the same time.
    • http://www.Apple.com/shop/product/MNN62AM/A/iPhone-lightning-dock-black?FNODE=97
  • Lightning Audio Belkin + load RockStar™ - coming soon - will allow you to charge your iPhone, just as listening to music through a wired headset. It supports the use of:
    • The EarPods (or other headphones), equipped with lightning connector.
    • Headphones with a 3.5 mm jack plug, when connected through the lightning to 3.5 mm Jack adapter (that comes with the iPhone).
    • http://www.Belkin.com/us/F8J198-Belkin/p/P-F8J198/

  Other accessories can follow in time Apple or third-party manufacturers.

  When purchasing an accessory for your iPhone, make sure that it is a true Apple product, or that - as Belkin product - it has been certified as made for iPhone (IFM).

• Hi people. Intend to purchase Apple Watch USA and use it in Europe. Will this be a problem? Can I use only a simple switch of 3rd party? I'm going to hurt same hardware or software?

  Intend to purchase Apple Watch USA and use it in Europe. Will this be a problem? Can I use only a simple switch of 3rd party? I'm going to hurt same hardware or software?

  Hello

  You will be able to use the watch in Europe.

  There is no regional differences in the hardware and the software can be configured to your chosen region. The supplied USB power adapter will have to pine trees located in the United States. A travel adapter will allow you to connect it to the European outlets.

  Alternatively, you can buy an Apple USB power adapter that is located in your country of destination / country.

  For example:

  • 2-pole:
    • http://www.Apple.com/FR/shop/product/MD813ZM/A/Adaptateur-secteur-USB-5-w-Apple? FNODE = 83
  • UK 3-pin:
    • http://www.Apple.com/uk/shop/product/MGRL2B/A/Apple-5W-USB-power-adapter-folding - pins? FNODE = 83

• My email has been hacked and used to send Spam. I have to perform a virus check, or simply change the password?

  My email has been hacked and used to send Spam. I have to perform a virus check, or simply change the password?

  Do not install or run an anti virus app.

  How do you know that your email has been "hacked"? It is a common practice for spammers to forge an envoy from the e-mail address. It may be that your email address has been misused. There's nothing to do if this is the case for you. The spammer will soon pass and usurp another email address.

  It's a good idea to immediately change your password by email if someone would actually managed to access your e-mail account.