vCentre Server 2.5 cannot connect to the VSphere host
vCentre Server 2.5 with VMware 3.5 host work well, but it cannot connect to VSphere host.
On step 4: ready to perform, there is an error message:
Cannot access the specified host. He either does not close, the server software does not respond, or there is a network problem.
In fact, I can see all the virtual machines on the host vSphere on phase II: summary of the host. So, I do not suspect the problems to which the error message mentioned above. I really want to know how vCentre 2.5 Server can work with vSphere well.
Thank you!
George
Hello
vCenter Server 2.5 is not compatible with vSphere 4.x host. I think that VMware announced document compatibility matrix (between hypervisor host ESX and vCenter Server or other components). Please see below URL:
www.VMware.com/PDF/vSphere4/R41/vsp_compatibility_matrix.pdf
Tags: VMware
Similar Questions
-
vMotion fails at 9% - Source host cannot connect to the destination host
Hello
I wonder if someone could shine any light on why vmotion fails to occur between an ESXi host who has just been restarted, in order to test HA. I have the following configuration:
3 x ESXi5 DL360 G7s with two 4-way NIC
VSphere Vcenter 5
1 x cluster configured for DRS HA
2 x Procurve 2910 - 24G
The switches are not connected to each other.
Both switches are configured as such:
All ports are not marked. NO PLEASE, no routing
Each host vMotion vSwitch is connected to two switches by 1 x 1 GB nic
I configured a vswitch on each host of vMotion. There are two ports vmkernel with two IPS on the same subnet. There are two vmnic attached to the vSwitch. On each port, a Vmic is configured to be active while the other is unused. I enabled frames on the vSwitch and 2910 switches. A VLAN has been configured on the two predisposees 2910 for vmotion with frames and defined traffic on "no label". I can successfully vmkping all the ip s vmotion on all ESXi hosts. However, when I test HA by stopping an ESXi host, when I restart the ESXi host I am unable to vmotion in that ESXi host. When I test vmkping I find that the host rebooted can only vmkping itself and no other host can vmkping it. Vmotion attempt fails on 9% and errors with the source host cannot connect to the destination host. If I restart the two switches of 2910 I can then perform a vMotion and the vmkping is a success.
Help, please?
Thank you
lansley2000 wrote:
I have since read up on the various load balancing options and find that your method is preferable during the method of "ip hash.
I'll make the change to "port based" and link the two switches
Hello Simon, I think it's a good option to do, since the hash IP load balancing is a bit special and really requires both interfaces to connect to the same physical switch, which must also have a specific configuration. If you like the results after the new changes.
-
My 5s iphone suddenly showed no service, then I made an attempt to update to ios and itunes connected, now iphone is not enable and display cannot connect to the server and in itunes it shows unable to check your device.please help me
Assuming that you have a valid SIM card in the phone, it is more often symptomatic of a phone that has been hacked or jailbroken to unlock.
Where do you have the phone first?
-
iPhone cannot connect to the server to iCloud
Hello!
My son IPhone cannot connect to the server iCloud. App Store is not available. In the iTunes and App Store from the settings app, I can't log in. IPhone resetting is not possible. Restore from iTunes on Mac is not possible, because find my iPhone is active on the iPhone, and it cannot be turned off, because in the pane of the application of the iCloud settings can't do anything until I have to accept the new terms and conditions, which cannot be made.
WiFi on the phone works great with Safari, Mail, but cannot get new e-mail messages. The weather application does not connect.
His iPad that is connected to the same iCloud account has no problem and there is no problem to connect to his account on iCloud.com.
I tried to restart and reset hard iPhone and updated to 9.3.4 via iTunes on Mac (which went without pain, but doesn't change anything).
Any help much appreciated!
Does anyone have advice at all...? Aside from throwing the thing?
-
Help! Safari cannot connect to the server
I really need help! I tried to forget the network and turning it back on, I have disabled the firewall and remove all extensions of safari. I seems that nothing works.
I get the message 'Safari cannot connect to the server' on almost every site except this and facebook. I can't enter same Urbanoutfitters.com or ASOS. I just got the message "Safari could not connect to Server" I'm not a computer genius so hopefully someone here can help me...
You may have installed one or more variants of the malware "VSearch' ad-injection. Please back up all data, and then take the steps below to disable it.
Do not use any type of product, "anti-virus" or "anti-malware" on a Mac. It is never necessary for her, and relying on it for protection makes you more vulnerable to attacks, not less.
Malware is constantly evolving to work around defenses against it. This procedure works now, I know. It will not work in the future. Anyone finding this comment a couple of days or more after it was published should look for a more recent discussion, or start a new one.
Step 1
VSearch malware tries to hide by varying names of the files it installs. It regenerates itself also if you try to remove it when it is run. To remove it, you must first start in safe mode temporarily disable the malware.
Note: If FileVault is enabled in OS X 10.9 or an earlier version, or if a firmware password is defined, or if the boot volume is a software RAID, you can not do this. Ask for other instructions.
Step 2
When running in safe mode, load the web page and then triple - click on the line below to select. Copy the text to the Clipboard by pressing Control-C key combination:
/Library/LaunchDaemons
In the Finder, select
Go ▹ go to the folder...
from the menu bar and paste it into the box that opens by pressing command + V. You won't see what you pasted a newline being included. Press return.
A folder named "LaunchDaemons" can open. If this is the case, press the combination of keys command-2 to select the display of the list, if it is not already selected.
There should be a column in the update Finder window. Click this title two times to sort the content by date with the most recent at the top. Please don't skip this step. Files that belong to an instance of VSearch will have the same date of change for a few minutes, then they will be grouped together when you sort the folder this way, which makes them easy to identify.
Step 3
In the LaunchDaemons folder, there may be one or more files with the name of this form:
com Apple.something.plist
When something is a random string, without the letters, different in each case.
Note that the name consists of four words separated by dots. Typical examples are:
com Apple.builins.plist
com Apple.cereng.plist
com Apple.nysgar.plist
There may be one or more items with a name of the form:
com.something.plist
Yet once something is a random string, without meaning - not necessarily the same as that which appears in one of the other file names.
These names consist of three words separated by dots. Typical examples are:
com.semifasciaUpd.plist
com.ubuiling.plist
Sometimes there are items (usually not more than one) with the name of this form:
com.something .net - preferences.plist
This name consists of four words (the third hyphen) separated by periods. Typical example:
com.jangly .net - preferences.plist
Drag all items in the basket. You may be prompted for administrator login password.
Restart the computer and empty the trash.
Examples of legitimate files located in the same folder:
com.apple.FinalCutServer.fcsvr_ldsd.plist
com Apple.Installer.osmessagetracing.plist
com Apple.Qmaster.qmasterd.plist
com Apple.aelwriter.plist
com Apple.SERVERD.plist
com Tether.plist
The first three are clearly not VSearch files because the names do not match the above models. The last three are not easy to distinguish by the name alone, but the modification date will be earlier than the date at which VSearch has been installed, perhaps several years. None of these files will be present in most installations of Mac OS X.
Do not delete the folder 'LaunchDaemons' or anything else inside, unless you know you have another type of unwanted software and more VSearch. The file is a normal part of Mac OS X. The "demon" refers to a program that starts automatically. This is not inherently bad, but the mechanism is sometimes exploited by hackers for malicious software.
If you are not sure whether a file is part of the malware, order the contents of the folder by date modified I wrote in step 2, no name. Malicious files will be grouped together. There could be more than one such group, if you attacked more than once. A file dated far in the past is not part of the malware. A folder in date dated Middle an obviously malicious cluster is almost certainly too malicious.
If the files come back after you remove the, they are replaced by others with similar names, then either you didn't start in safe mode or you do not have all the. Return to step 1 and try again.
Step 4
Reset the home page in each of your browsers, if it has been modified. In Safari, first load the desired home page, then select
▹ Safari preferences... ▹ General
and click on
Set on the current Page
If you use Firefox or Chrome web browser, remove the extensions or add-ons that you don't know that you need. When in doubt, remove all of them.
The malware is now permanently inactivated, as long as you reinstall it never. A few small files will be left behind, but they have no effect, and trying to find all them is more trouble that it's worth.
Step 5
The malware lets the web proxy discovery in the network settings. If you know that the setting was already enabled for a reason, skip this step. Otherwise, you should undo the change.
Open the network pane in system preferences. If there is a padlock icon in the lower left corner of the window, click it and authenticate to unlock the settings. Click the Advanced button, and then select Proxies in the sheet that drops down. Uncheck that Auto Discovery Proxy if it is checked. Click OK, and then apply.
Step 6
This step is optional. Open the users and groups in the system preferences and click on the lock icon to unlock the settings. In the list of users, there may be some with random names that have been added by the malware. You can remove these users. If you are not sure whether a user is legitimate, do not delete it.
-
Outlook: "cannot get mail" "cannot connect to the server.
April 6 at 7:00 PM CST, my iPhone 5 running iOS stopped syncing with my Microsoft Outlook account 9.3.1.
I did have problems with my iPhone sync with my Outlook email over the past 5 years so far.
My Outlook account is to these servers-
web mail:
https://blu183.mail.live.com/for Windows Live Mail 2012:
https://mail.Services.live.com/DeltaSync_v2.0.0/sync.aspxI tried to delete my Outlook account from my iPhone and re-establishment and the account Outlook 'checks' correctly - but this does not solve the problem.
The iPhone keeps displaying a pop-up message:
"Cannot get mail" "cannot connect to the server.My iPhone is syncing correctly with my Gmail accounts and iCloud.
Also, I created my Outlook account on iPad to my daughter who is running iOS 8.1.2 and I have the same problem.
This seems to be a situation of the Apple servers, do not sync with Microsoft servers.
Thank you
It seems that Outlook is to have questions, not only with iPhones but W10, see this thread:
-
Some Web pages do not allow (safari cannot connect to the server)
I can't access some Web pages like the movie online, eBay, Amazon, etc. sites, when I try, I got the note as 'safari cannot connect to the server' and my chrome also got error like massage "this webpage is not available" more my App Store unable to work properly can not download updates»» I tried to delete all the data of the website... and uninstall extensions, but there was not work //I got a MacBook Pro 2014 middle with OS X EL capitan 10.11.2//some on help me please
Please remove the 'ESET' product (if you have it installed) by following these instructions. If you have a different version of the product, the steps may be different.
Back up all data before making any changes. Never install any product "anti-virus" or "anti-malware" again.
-
FSX won't turn on, says that it cannot connect to the server
Hey, I tried to register my copy of Microsoft flight simulator X deluxe edition and it does not work I tried to register it hourly it says it cannot connect to the server);
Hello
What version of Windows operating system do you use?
I suggest you to consult the following Microsoft article and check if it helps.
Solve problems with activation for Microsoft games problems and mapping programs
http://support.Microsoft.com/kb/960480
Note : the steps mentioned below includes the modification of the system registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
Back up the registry: http://windows.microsoft.com/en-US/windows7/Back-up-the-registryAlso see: frequently asked questions on how to enable Microsoft Games for Windows, streets and trips and Mappoint: http://support.microsoft.com/kb/927007If you still experience the problem, then I suggest to contact with support of Flight Simulator for further assistance.
http://support.Microsoft.com/GP/games-for-Windows
http://www.Microsoft.com/products/games/FSInsider/tips/pages/default.aspx
-
A Windows Server 2003 Standard Edition SP2 32-bit computer is a field, the file and print server.
A computer on the domain is a machine of Windows 7 Ultimate 64 - bit with HP DesignJet 500 24 printer connected via USB. The printer is running the latest firmware. The PC is running the latest 64-bit drivers with no problems to the host machine printing. The host also has the latest drivers 32-bit (x 86) installed by downloading by other computers on the network. The printer is configured to share with the share name of HPDJ500.
Now, on a machine Windows XP Pro SP3 32 bit on the field, I'm trying to connect to the shared printer. Add a printer > click Next in the wizard of > check "a network printer or a printer attached to another computer" and then click Next > click on "Find a printer in the directory", then click Next > click Find now > HPDJ500 in the list below (the XP machine can see the shared printer on the Windows 7 computer!) and click OK. At this point, I get an error that says: "Windows cannot connect to the printer. The name of the printer has been correctly entered, or the specified printer has lost its connection to the server. For more information, click Help. »
Alternatively, if I right-click on the HPDJ500 printer listed, then click on connect, I get the same error message but I also see a separate window that says "Connecting to HPDJ500 on H2.ws.net" with the lively projector. This window also disappears as soon as I clear the error message.
Please note that this printer worked perfectly as a printer shared, hosted on a machine XP 32 bit on the field. It works perfectly for the new Windows 7 64-bit machine, but we cannot connect from anywhere else on the network (including the server which translates the same exact error message). On the server, I also preinstalled drivers thinking there was a problem with a 32-bit computer, trying to grasp the correct drivers from the host 64-bit Windows 7, but that doesn't change anything.
How connect to this printer?
Try using the path UNC path of the printer in the Add Printer Wizard.
Add a printer > network printer > connection to this printer ((deuxieme point)
Click next to browse (leave blank, the name field) or type the UNC path of the printer (i.e. \\Computername\Printername) path
-
Media Player cannot connect to the server - Original COOD2EE7 error code
Tried media player - tools - options-network. Cannot configure the Protocol / the proxy settings. Streaming proxy settings area is empty.
Hello Adelek,
Thank you for posting. It seems that you may have a firewall problem. I that you would suggest to check your firewall settings to see if it's to allow access of media player. I've also included some basic information about this error.
Please let me know if this helps you.
You got the C00D1198 error message when you use Windows Media Player. The following information can help you resolve the problem.
Unable to connect to the server
Windows Media Player cannot connect to the server that hosts the content you want to listen to. You may encounter this error message for the following reasons:
The name of the server that hosts the content is not valid. If you typed an address Uniform Resource Locator (URL) in the open URL dialog box, verify that the file name is spelled correctly and that the path to the file is correct, and then try again. If you clicked a link on a Web page, the link isn't valid.
The server is not available (for example, the server is busy or not online). Try again later.
For Windows Media Player proxy server settings are not configured correctly. Verify that your proxy server settings are correct.
To check your proxy server settings
Click the arrow below the now playing tab, and then click More Options.
Click the network tab.
Check your settings in the Streaming proxy settings area.
Note
If you don't know what your proxy server settings should be, on the network tab, select a Protocol, click on configure, then select Autodetect proxy settings or use the the proxy settings of the browser (available for HTTP protocol only).
Zack
Engineer Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think. -
original title: Microsoft Lync
Unable to connect to Lync
Cannot connect because the server is temporarily unavailable.
If the problem persists, contact the support team.Well, given that the server is temporarily unavailable, you cannot connect. If you wish to contact the support team, you contact the Lync support team. Nothing to do with this forum.
-
Original title: Media Player all of a sudden will not play the dvd.
Suddenly, I can't play DVDs on my laptop. The error message is: Windows Media Player cannot connect to the server. The name of the server are may not be not correct, ther server name maybe isn't available, or your proxy settings are may not be not correct. Any suggestions on troubleshooting of Microsofts page appear to be relevant.
Hi mcraigQY
1. when exactly you get the error message?
2. you try to listen to music from any remote location or try to play a DVD?
3 have you tried to play a different CD or DVD?
4. what happens when you play the same DVD on another computer?5. for how long have you been faced with this problem?
6. the DVD folder that you are trying to play supported by the windows media player is it?
7. What is the type of DVD that you try to play?Let us know the answers to help you best.
-
vWorkspace 8 - VDI Windows 7 "Error cannot connect to the server '.
Hello
We are soon about to begin the deployment of our vWorkspace VDI solution. We have Windows 7 Client s connection to Win 7 Pro 32 Bit VM on Hyper-V.
Sometimes when the user intiates a connection to the desktop of Windows 7 VDI published the vWorkspace Client launch and are trying to connect, and then an error will be presented "Error cannot connect to the server. We do not understand all the time and it is random.
Go it is addressed urgently as it's going to cause some major headaches with our users.
Someone at - it ideas?
Cool, thanks Dan.
I'll find the case of Mike and send the info from there.
-
The blackBerry Smartphones No. MMS option and cannot connect to the application server
Good evening
For some reason any I can not receive or send MMS on my Blackberry 9520 Storm 2. I still do not see the ability to send a picture as a text when I go on my photos. I don't know if it's the phone or my provider. I have my 9520 unlocked on AT & T with a package data unlimited talk and text unlimited. I tried to have photos I was sent as well, but it was also no chance that I NEVER received a text.
The second problem I have is that I can't access the Blackberry App Store. Try whenever I have it says that it cannot connect to the server.
Any help?
Edit: The problem of the App Store is no longer present (off the network and turned it back), but the MMS problem is still present.
Hello!
I suggest the following:
(1) registry HRT
- Homescreen > Options > Advanced Options > host Routing Table > BBKey (it matter little what line is current) > sign up now
(2) Service reference books
- KB02830 Send the directories for the BlackBerry Internet Service
(3) restart to take batt
- Each time a random strange behavior or slow creeps, the first thing to do is a battery pop reboot. With power ON, remove the hood back and remove the battery. Wait a minute, then replace the battery and cover. Power on and wait patiently through the long reboot - about 5 minutes. See if things return to functioning. Like all computing devices, BB suffers from memory leaks and others... with a hard reboot is the best remedy.
I hope that will move things again for you! But, the fact that you can't do SMS or MMS seems to indicate that they are not part of your plan service provider - that is why, if the above does not help, then contact them to see if you who are on your plan on their part.
Good luck and let us know!
-
established - VPN connection, but cannot connect to the server?
vpn connection AnyConnect is implemented - but cannot connect to the server? The server IP is 192.168.0.4
Thank you
ASA Version 8.2 (1)
!
hostname ciscoasa5505
names of
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.0.3 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 208.0.0.162 255.255.255.248
!
interface Vlan5
Shutdown
prior to interface Vlan1
nameif dmz
security-level 50
IP address dhcp setroute
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
clock timezone PST - 8
clock summer-time recurring PDT
DNS lookup field inside
DNS server-group DefaultDNS
192.168.0.4 server name
Server name 208.0.0.11
permit same-security-traffic intra-interface
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service TS-780-tcp - udp
port-object eq 780
object-group service Graphon tcp - udp
port-object eq 491
Allworx-2088 udp service object-group
port-object eq 2088
object-group service allworx-15000 udp
15000 15511 object-port Beach
object-group service udp allworx-2088
port-object eq 2088
object-group service allworx-5060 udp
port-object eq sip
object-group service allworx-8081 tcp
EQ port 8081 object
object-group service web-allworx tcp
EQ object of port 8080
allworx udp service object-group
16001 16010 object-port Beach
object-group service allworx-udp
object-port range 16384-16393
object-group service remote tcp - udp
port-object eq 779
object-group service billing1 tcp - udp
EQ object of port 8080
object-group service billing-1521 tcp - udp
port-object eq 1521
object-group service billing-6233 tcp - udp
6233 6234 object-port Beach
object-group service billing2-3389 tcp - udp
EQ port 3389 object
object-group service olivia-3389 tcp - udp
EQ port 3389 object
object-group service olivia-777-tcp - udp
port-object eq 777
netgroup group of objects
network-object host 192.168.0.15
network-object host 192.168.0.4
object-group service allworx1 tcp - udp
8080 description
EQ object of port 8080
allworx_15000 udp service object-group
15000 15511 object-port Beach
allworx_16384 udp service object-group
object-port range 16384-16393
DM_INLINE_UDP_1 udp service object-group
purpose of group allworx_16384
object-port range 16384 16403
object-group service allworx-5061 udp
range of object-port 5061 5062
object-group service ananit tcp - udp
port-object eq 880
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing-6233
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing-1521
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing2-3389
outside_access_in list extended access permit tcp any host 208.0.0.164 eq https
outside_access_in list extended access permit tcp any host 208.0.0.164 eq www
outside_access_in list extended access permit tcp any host 208.0.0.164 eq ftp
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing1
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 EQ field
outside_access_in list extended access permit tcp any host 208.0.0.162 eq www
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 remote object-group
outside_access_in list extended access permit tcp any host 208.0.0.162 eq smtp
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 object-group olivia-777
outside_access_in list extended access permit udp any host 208.0.0.162 - group Allworx-2088 idle object
outside_access_in list extended access permit udp any host 208.0.0.162 object-group inactive allworx-5060
outside_access_in list extended access permit tcp any host 208.0.0.162 object-group web-allworx inactive
outside_access_in list extended access permit tcp any host 208.0.0.162 object-group inactive allworx-8081
outside_access_in list extended access permit udp any host 208.0.0.162 object-group inactive allworx-15000
outside_access_in list extended access permit udp any host 208.0.0.162 DM_INLINE_UDP_1 idle object-group
outside_access_in list extended access permit udp any host 208.0.0.162 object-group inactive allworx-5061
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 inactive ananit object-group
outside_access_in list extended access deny ip host 151.1.68.194 208.0.0.164
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 172.16.0.0 255.255.0.0
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.1.0 255.255.255.0
permit access ip 192.168.0.0 scope list outside_20_cryptomap 255.255.255.0 172.16.0.0 255.255.0.0
Ping list extended access permit icmp any any echo response
inside_access_in of access allowed any ip an extended list
permit access ip 192.168.0.0 scope list outside_cryptomap 255.255.255.0 192.168.1.0 255.255.255.0
access-list 1 standard allow 192.168.0.0 255.255.255.0
pager lines 24
Enable logging
logging buffered stored notifications
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 dmz
IP local pool 192.168.100.30 - 192.168.100.60 mask 255.255.255.0 remote_pool
192.168.0.20 mask - distance local pool 255.255.255.0 IP 192.168.0.50
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 1 192.168.0.0 255.255.255.0
alias (inside) 192.168.0.4 99.63.129.65 255.255.255.255
public static tcp (indoor, outdoor) interface 192.168.0.4 smtp smtp netmask 255.255.255.255
public static tcp (indoor, outdoor) interface field 192.168.0.4 netmask 255.255.255.255 area
public static tcp (indoor, outdoor) interface 192.168.0.4 www www netmask 255.255.255.255
public static tcp (indoor, outdoor) interface 777 192.168.0.15 777 netmask 255.255.255.255
public static tcp (indoor, outdoor) interface 779 192.168.0.4 779 netmask 255.255.255.255
public static (inside, outside) udp interface field 192.168.0.4 netmask 255.255.255.255 area
public static tcp (indoor, outdoor) interface 880 192.168.0.16 880 netmask 255.255.255.255
static (inside, outside) 208.0.0.164 tcp 3389 192.168.0.185 3389 netmask 255.255.255.255
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 208.0.0.161 1
Route inside 192.168.50.0 255.255.255.0 192.168.0.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.0.0 255.255.255.0 inside
http 192.168.0.3 255.255.255.255 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Sysopt noproxyarp inside
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 108.0.0.97
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
card crypto outside_map 20 match address outside_20_cryptomap
card crypto outside_map 20 set pfs
peer set card crypto outside_map 20 69.0.0.54
outside_map crypto 20 card value transform-set ESP-3DES-SHA
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 5
preshared authentication
3des encryption
sha hash
Group 2
life no
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 1
life no
Telnet timeout 5
SSH timeout 5
Console timeout 0
identifying client DHCP-client interface dmz
dhcpd outside auto_config
!
dhcpd address 192.168.0.20 - 192.168.0.50 inside
dhcpd dns 192.168.0.4 208.0.0.11 interface inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image
enable SVC
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
internal group anyconnect strategy
attributes of the strategy group anyconnect
VPN-tunnel-Protocol svc webvpn
WebVPN
list of URLS no
SVC request enable
encrypted olivia Zta1M8bCsJst9NAs password username
username of graciela CdnZ0hm9o72q6Ddj encrypted password
tunnel-group 69.0.0.54 type ipsec-l2l
IPSec-attributes tunnel-group 69.0.0.54
pre-shared-key *.
tunnel-group 108.0.0.97 type ipsec-l2l
IPSec-attributes tunnel-group 108.0.0.97
pre-shared-key *.
tunnel-group anyconnect type remote access
tunnel-group anyconnect General attributes
remote address pool
strategy-group-by default anyconnect
tunnel-group anyconnect webvpn-attributes
Group-alias anyconnect enable
!
Global class-card class
match default-inspection-traffic
!
!
World-Policy policy-map
Global category
inspect the icmp
!
service-policy-international policy global
: end
ASDM location 208.0.0.164 255.255.255.255 inside
ASDM location 192.168.0.15 255.255.255.255 inside
ASDM location 192.168.50.0 255.255.255.0 inside
ASDM location 192.168.1.0 255.255.255.0 inside
don't allow no asdm history
Right now your nat 0 (NAT exemption) follows the access list:
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 172.16.0.0 255.255.0.0
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.1.0 255.255.255.0
Traffic back from your server to 192.168.0.4 in the pool of VPN (192.168.0.20 - 50) not correspond to this access list and thus be NATted. The TCP connection will not develop due to the failure of the Reverse Path Forwarding (RPF) - traffic is asymmetric NATted.
Then try to add an entry to the list of access as:
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.0.0 255.255.255.0
It's a bit paradoxical but necessary that your VPN pool is cut out in your interior space network. You could also do like André offers below and use a separate network, but you would still have to add an access list entry to exempt outgoing NAT traffic.
Maybe you are looking for
-
This always happens when click on something... .and cannot get the cursor back a few seconds... will not link or to open a page... asks what I want to stop or continue plugin.Thank you!
-
Portege M700 will not change the screen orientation
I installed the driver for the webcam for the M700, and every time I install it, I get the same error message: "Open Webcam driver fail - please restart camera or computer." I reinstalled the drivers of many times, and it still does not work. Therefo
-
have you tried all the suggestions, nothing worked. using the keyboard to the screen. I tried removing battery, pilot reistalling, restart.
-
Audio glitch: may be associated with fan?
With regard to the previous assignment "audio glitch: may be associated with fan" February 27, 2007 [LINK]http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=18631&start=0 As this post has now been locked, I have re-posted here in
-
Where can I get driver SATA WinXP for Satellite L30?
I have a Satellite L30-10 X with Windows Vista preinstalled and the plan to downgrade the OS to Windows XP Pro, but it takes the pilot special SATA to the first phase of the installation. Will create a Windows 'unmanned' distributive using nLite, but