Very amplified speaker nois

Similar Questions

• HP 15 au006tx: very low speaker quality I can't hear anything

  Hello.. I bought a new computer hp laptop for 2 months... My laptop works properly... But the speaker is of very poor quality... If I here all important videos I can not here anything from here... The quality of the speaker is very low worm... very bad... If I put a full volume, it's just like a normal sound otherwise very bad sound... I need a good solution... Please help me what I have to do?

  In fact I need DOLBY speakers to my laptop... If possible could I change my B & O Dolby? How do change?

• Satellite A100 - very low speaker volume

  Hello

  Recently, the volume of my speaker has been very low - barely audible.
  The speakers are Realtek High definition.

  The volume is set at 100%. I checked the properties of reading, recording and sounds and they all work very well.
  The problem occurs if I play CDs, videos online or applications such as RealPlayer - anything really.

  Any advice would be much appreciated.

  Thank you

  Gary

  Hello

  I guess you are which means that the sound card (it s Realtek High definition) and not speakers ;)
  However, have you checked the settings in the control panel-> Manager Realtek HD?

  Do it! There are a lot of different parameters that control the quality of the sound and there you can assign different audio effects

  I think you should check this certainly!

• Very low speaking volume - Dell Inspiron

  Hello, I bought 2 notebooks of Dell Inspiron 3542 in January

  The internal speaker on each volume is very low as a whisper, even at 100%.

  The drivers are up to date.

  Looking for ideas on how to increase the volume.

  Thank you very much.

  Dear Sujatha, k.

  Thank you very much for your suggestions continue, but I spent hours to set up two laptops in the way that I need them and hours more, to try to resolve the issue of the speaker, namely extremely low volume even in the setting of 100 percent.  I don't want to just go back to factory default, or risk losing data or settings to devote more time to it.  Unfortunately, I'll live with the present situation.  I really appreciate any suggestions.  I conclude that it is a design problem.  Larry

• does not not all his sound and the device very bad speaker volume if not possible you help thank you

  Send OR you notice once more and I look forward to you helps maybe not possible with this problem-not working not not everyone - his device speaker volume and sound. Thank you

  d

  Hello

  ·         Have you tried the steps provided by Rob.C in this thread?

  ·         You receive an error message or error code?

  Please, try the steps indicated by the Rob.C of your previous thread and I would also ask you do not to create duplicate threads. This will not help you to get the instant solution to the issue that you are facing.

  Let us know the results so that we offer in addition to the steps to solve the problem of troubleshooting.

• Jack on speaker N5050

  Can I get information about jack speaker its Inspiron 15 (N5050) (where the sign of the helmet is represented) combination of interface? Y at - it all? For example, then after this plug (where is represented the micro sign) has a: it can be used not only for the microphone connection, but also for "Line-In" connection. My question is addressed to competent engineers, knowing N5050 techspecs.

  I could receive a knowledge exactly, speaker can be used as a "Line-Out", or, in other words, he has the combination with "Line-out"? It is very important, because sound I want to use is prohibited for binding connector speaker and authorized only for the 'Line Out', otherwise it will be damaged.

  I hope that the comments of the competent Dell technicians. Thank you.

  Hello. Dell engineers do not personally answer here on the Dell Community Forum. However, I think I can answer your question. I'm no sound engineer, but I am well informed on the audio in general and audio Dell laptop in particular.

  The purpose of the output jack must be a headphone jack and an output jack line. You can use it safely in the form of a line.

  green_DellSupport

  It is very important, because its material I want to use is forbidden for binding connector speaker

  This means you can't plug your sound equipment directly on a power amplifier speaker terminals.

• Adding a Bluetooth to his Bar CT660 speaker

  Can someone tell me how to add a Portable Bluetooth speaker to Sound Bar CT660?

  I'll buy the speaker that can anyone suggest preferably a very small speaker.

  Thank you.

  Hi dailymeat,

  You cannot add a portable speaker to a sound bar. They both have the same INPUTS and BLUETOOTH functionality cannot RECEIVE bluetooth signals.

  Thank you

  > Joffrey

  If my post answered your question, please mark it as "accept as a Solution.

• Satellite C645-SP4131L - audio disappears after 10-15 seconds of game

  Hello, help me with this problem:

  Whenever I try to play music files at high volume, the sound goes away after 10-15 seconds or more, but at this time I plug in a headset and then disconnected after 2 seconds, the sound from the speakers of the laptop back, but after 10-15 sec disappears again.

  A special case is that when I play a file any with the low volume, the sound from the speakers does not disappear.
  I tried to reinstall the current driver, with the right system I (windows 7 professional 64-bit)

  It is not virus problem (I can play with headphones and listening to higher volume).
  Also disable the built-in microphone, believing that it was a bad configuration or the coupling of the signal, this problem seems to indicate that it is a technical failure

  The audio output amplifier speaker which is a failure?

  Is it diagnostic software to try to know what the actual fault? I hope that your answers, thank you for reading my post.

  Sorry if I am not clear, I do not speak very good English

  > A special case, is that when I play a file any with the low volume, the sound from the speakers does not disappear.
  Have you noticed the same thing using earphones?
  Theoretically, it could be just a problem of speaker and no sound driver problem.
  But that would mean that the speakers of the laptop must be replaced.

• I don't have the money to buy a new computer and would not be vulnerable by using your latest version of Firefox. I want to stay with the previous version.

  I saw a previous question to a windows user, but it seemed that he was very long (speaking of the 3.x.x editions), and all links on this thread seemed to have only 3 updates. I just want to stay with the version of Firefox before this last update (30/10/12) who say 16.0.2 work well with my older Mac OSX. Can you provide me with a link to reinstall and forgive my ignorance, but let me know exactly what I have to do to avoid losing preferences and bookmarks and others? Thank you very much.

  All versions of Firefox 16 still work with your operating system OS X 10.5, but this is the last version that works.
  
  Firefox 17 will require OS X 10.6 and later.

  Here you can see the 17 Firefox (currently in beta) system requirements:
  http://www.Mozilla.org/en-us/Firefox/17.0/system-requirements/

• Problem with the electric guitar and Satellite A100-906

  Hello

  I get a strange sharp sound of my guitar amp speaker when I try to play starting from the monitor of my laptop. Is this normal? I used to play in front of a screen LCD LG and everything was nice and quiet.

  However a few minutes ago, I discovered the FL inverter, which exists in the monitor to my laptop and was not on my LCD. FL-ups would cause this noise to my guitar? I want to emphasize that I can not hear the sound of my monitor. I can only hear it through my guitar and the amplifier speaker microphones.

  I hope you understand my problem.
  Looking forward to a response!

  Thank you
  Nikos

  Hello

  I n t have guitar and can't be 100% sure about your question, but perhaps you need a sort of Notebook Surge Station and noise filter. Google a bit and look for info on this filter.

• SS-tsb101 speakers 3 ohms.

  I want to drive a pair of l/r of the ss-tsb101 speakers 3 ohms with a small audio amp. Can someone tell me what power amp should I use? I can't find the rated power of these speakers. Any help is greatly appreciated. Thank you, [email protected].

  Hello Curt,.

  You can use amplifier with an impedance of 3 ohms 100W.
  To connect these speakers to an amplifier, the impedance or the ohms speaker side must match that of the receiver.
  Also, speaker connectors must match with that of the catch located on the amplifier speaker.

  Please mark it as "acceptable Solution" If you find this information useful.

  Kind regards
  Colby

• Microsoft Update

  Microsoft Update suggests the installation of several upgrades of .net. They must for my laptop (I'm not a developer)

  Concerning

  Tony

  Very generally speaking...

  If they are kept up-to-date of security (e.g., KB983582;) KB983583), Yes, you should install them.

  If they optionally, non-security updates (e.g., KB982167;) KB982168; KB982524; KB982671), you can hide them.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Why I can't download and install windows xp SP3?

  I am running Windows XP Pro SP2. My internet security program is Norton Antivirus online, provided by my ISP, Qwest... When I try to upgrade to SP3, my computer is getting ready for download, begins to check the download, then goes back to prepare for the download. Can I get a failure to download, with Ox80070005 error code I tried to download and install from the center of update and from the Microsoft Download Center, with the same results. Anyone can solve this for me, PLEEEEEEASE!  My computer is an old PC HP Pavilion Media Center Desktop, model #m370n. I connect to the internet through a gateway of Qwest. Model # Actiontec PK5000 modem. Please let know me if more information is needed. Thank you.

  [1] your solutions solved my problems!

  [2] but, I still wonder if it is advisable to remove the update section of the section add/remove from the Control Panel, already installed updates if updates do not apply to the version and service pack of windows I use!

  [3].. .when I was running Norton security, I kept getting messages from the use of the high memory for many programs I was running. So I guess what I'm asking is, how can I safely free up memory on my drive if I am at or near the limit of memory?

  A1. Excellent! And kind of you, too much work.

  A2. Well, this would be a "double edge" => If you uninstall an older update (in order to "save space") and then find that you need to uninstall a more recent update that replaced (replaced) the former for a reason, you wouldn't be able to do.

  That being said, see this discussion archived in another forum (where I also "hanging out") for a few suggestions related to dispose of "unnecessary updates...

  XP SP3: Post Installation Cleanup
     http://aumha.NET/viewtopic.php?f=62&t=33827

  A3. Let me ask you this: are seeing you this "high memory use" alerts now?

  Speaking of which, you reinstall Norton Internet Security Online of Qwest or have you installed Microsoft Security Essentials to step #6 of my previous answer?

  Remember that the available memory is not necessarily related to the amount of available disk space. If you want to read / learn more, see the section of the optimization of your computer here: http://aumha.org/win5/articles.htm

  Very generally speaking, running Disk Cleanup every moment & should be all you need to do (especially if you no longer have an installed Norton application). Refer to the section of the free disk space up to here: http://www.microsoft.com/atwork/maintenance/speed.aspx

  If you have further questions about performance, post them here: http://answers.microsoft.com/en-us/windows/forum/windows_xp-performance

• Alienware m17x R4 Digital Out question

  For a long time, I had a problem with my digital output. I can't really 5.1 audio on my computer even when it is plugged into my audio receiver. I have the Sound Blaster Recon 3Di, but there is no option to set the DTS or the sound of doby. If I go to playback devices and click on properties, I test Dolby digital, and I hear all the speakers work. But the sound-blaster software does not work unless I chose to play stereo sound to the digital way. Can I get the front speakers. 5.1 selected with the sound-blaster software give me only the front speakers. It seems that it is only play stereo no matter what camera I have set for the sound, speakers, digital output or my TV.

  I guess that the sound blaster software has no opportunity to tell pilots to use 5.1 instead of stereo. I use Windows 8.1, but I think that it does the same thing, even when I was with Windows 7. In the channel mixer adjustment menu, it shows only 2 channels for the digital output. I wonder if it's a driver issue or a setting in windows that I need to fix. Any ideas?

  Hello. This section of the forum deals mainly with computers Dell laptops with Realtek, IDT and Conexant audio. Only the Alienwares have Creative sound cards, so I don't know much about what you can do with this hardware/software. There is a section called the Alienware Club. If you post here tell them that you posted already here while they just refer.

  Having said that, here's what I 'think' goes with your sound on what I know about the other Dell laptops. The Quick Installation Guide for your model of watch you have 3 Sockets audio, all capable of output to speakers when it is configured to do this. In other words, the mic socket can become an extra speaker output jack. This means that you should have the ability to setup your laptop for a 5.1 speaker system surround and attaching the cables of 3 speaker (of an analog 5.1 amplified speaker system) for the 3 Sockets (front, rear, Center / LF). You must have a source that has a surround sound, like a dvd movie. I don't know if your creation can simulate surround sound when the source itself is only stereo.

  On the s/pdif connection. S/pdif is a 2 channel protocol. When there are additional channels from a source that contains a sound surround, they are coded into the main stereo signal. The receiving device must be capable of decoding the surround channels and transmitting them to the speakers.

  When you use 3 analog computer Sockets, the computer performs the decoding, but when you use the s/pdif output computer does not because he would not be able to get additional channels decoded, as s/pdif carries only 2 channels. To the best of my knowledge, except for the selection of s/pdif to be the default playback device, there is no other software needed adjustment. Surround channels (if present in the source) will be included in the primary s/pdif signal and after that it is at the receiver. And if the source material does not contain the surround channels, then this is the receiving device to have the ability to simulate the if you want to hear through the other loudspeakers.

• Volume on the computer controls

  I have a windows 7 and the keyboard volume controls do not work how to operate again

  * Proposed by the moderator of "Windows/Windows 7 / Windows Other apps" for "Windows / Windows 7/Hardware & drivers."

  If you try to change the volume of the keyboard, you need to talk or see the instructions that are specific to your particular keyboard model.

  I suggest that you use either the volume of your speakers or the bottom left you screen (a very small speaker).  Just click on the small speaker and drag the cursor upwards or downwards for the volume change.