VM does not start after a power failure

Similar Questions

• How affect alienware x 51 auto does not start when a power failure?

  Hi I was at work today and we had a major storm, I fell from my pc to something alienware system repair. I've never seen before, I guess my computer must have tried from several times during power blinks, it's bad and not good for her, so how can I turn this behavior off that way, that it does not happen.

  Hello!

  Go to BIOS (press F2 repeatedly on the loading screen Alienware), then to the Advanced/Power Management Setup and turn AC OFF recovery.

• My computer does not start after losing power. He symbol WindowXP reacher, then resets. I tried from all different modes, but none works.

  Have tried all different modes for example. Ext. safe mode, restart the computer normally

  Have tried all different modes for example. Ext. safe mode, restart the computer normally

  Please use the recovery disk to repair the operating system...
  MD MOEEN AJAZ KHAN - MCP, N +, A +.

• Pavilion HPE H8-1121: Pavilion HPE H8-1121 - new graphics card + power supply does not start after screen HP (Revisited)

  I have the same problem as this post 2013!  Ouch. Pavilion HPE H8-1121 - new map chart + power supply, does not start after HP screen.

  I installed a new power supply (Seasonic 620W), which works well.  I also installed a GTX 660Ti last year and it was works fine as well.  I recently bought a ZOTAC GTX 970 and attempted to install it, but it will not go beyond the blue HP screen and I get the same code of beeps (1 long, 3 short), who, seems, suggests that the video is not initialized.

  My BIOS date is 2011.

  Where can I find an update for this?

  I'm also using Windows 10, which I found on the HP site is not tested on my model and would probably not favourable to good use.  Should I do back up to 7 or 8?  and then update the BIOS?  Y at - it a update for my BIOS and where can I find.

  In any case, I hope that this is a solution.  Again, this is not a bad machine to be 5 years old.

  Thanks for any help!

  If the video card that you have purchased dose not a legacy vBIOS it will never start. An update of the BIOS doesn't solve that.

  It is likely that your new video card has a vBIOS UEFI and that only is for the PC motherboards newer than yours which have a UEFI BIOS. Your motherboard has a legacy BIOS. 2012 is the year of model when the UEFI BIOS more or less became the de facto on motherboards standard.

  I return it for a refund. Find the candidate of video cards that support the old BIOS. It can be inherited only or switchable vBIOS (legacy or UEFI) vBIOS.  I suggest looking at the site of Sapphire Technology. ZoTac is not known to provide enough information about their video cards in the way. You upgrade a pre-built desktop PC and it's different and a little more difficult to set up a DIY PC. I looked at the site of Zotac and see that nothing is said about their video vBIOS cards.  I would return to the map.  Carefully read the specifications of the video card. A candidate for your motherboard card must have inherited vBIOS support or simply, it won't work.

  ZOTAC (they don't say anything about their product vBIOS)

  https://www.ZOTAC.com/us/product/graphics_card/GTX-970-amp-extreme-core

  Sapphire Technology

  http://www.sapphiretech.com/catapage_pd.asp?cataid=305&lang=eng

  Because you look at game with 4 GB cards. Take a look at the following map. It has a double vBIOS. legacy and UEFI. http://www.sapphiretech.com/productdetial.asp?pid=640A98CD-0CF0-4191-B75C-CA2800111ADB&lang=eng

  

• Computer does not start after the screen of the bios, Compaq Presario SR1023WM

  Ok. Trying to fix a friend's computer and seem to have met a strange barrier.

  Problem: The computer does not start after the bios screen.

  Details: When you turn on the computer, the compaq logo with intel inside is and has the < F1 Setup > and < F10 System Recovery > options listed as well.  And that's it as far as the computer becomes.  After that the computer just locked up, no work of buttons on the keyboard lights keyboard ect ect.  I tried the puree on the F1 key, as soon as I turn on the computer and I can handle so he can say * entering setup * but it freezes again after this point.  I already tried to eliminate the possible sources of the problem, removed all expansion cards, HDD and Dvd Rom module only disconnected, only memory (256 MB ddr 2700), power, vga and keyboard connected.  Ive also used the jumper on the motherboard to clear the cmos, hoping that would solve the problem without success.  I tried using a different memory stick and different memory as well...  Tried to use both a ps2 and a usb keyboard... Ive even tried pulling the rider for the protection of the bios password (even if she did not have a password on it, just try everything I can think of).

  The installed bios version is 3.1, and that's all that I know on the computer at this point, except that the website tells me to him.

  http://h10025.www1.HP.com/ewfrf/wc/product?product=411354 & LC = on & CC = US & DLC = in & Submit.y = 5 & Submit.x = 3 & lang = to & CC = US <-link to the Web page for the model #.

  I'm basically at a loss on this one, so if someone feels scroll line-by-line of their brains on this one, I'd be very happy.

  I have a pretty strong understanding of computer repair, so feel free to give me something to try.

  If you need more information out of me, let me know as well.

  Try to clear the CMOS again but this time remove CMOS battery and hold the power button on a few seconds. Replace the battery, then try to start back to the top.

  At the back of the pc is the condition of the PSU led green or flashing?

• Satellite P200D-130 does not start after upgrading RAM

  Hi, I just upgraded the RAM on my P200D 130 but it does not start after that.
  I removed the 2 Hynix 1 GB PC2-5200 and put in 2 SO Kingston DDR2 2 GB PC667 (should be the same as PC2-5200).
  Post-market nothing happens, light power control is turned on, I him stays CD drive but screen black, no beeps.

  I put one of the 1 GB modules, it starts normally, then I tried a 1 GB into the lower slot module and a 2 GB module in the top slot and it works.
  I tried a single 2 GB module in each slot, even in the form of 2 2 GB modules.

  What could be the reason, better: what would be the solution to ensure that the modules of 2 x 2 GB to work?

  Thanks in advance,

  Michael

  Hello!

  I think that both modules are not compatible to the laptop.
  Normally you can upgrade your laptop to 4 GB. Look in the user manual.

  The RAM, you should bring the computer dealer and request a new one. More buy modules with the same specifications and dimensions. Try buying RAM with the same specs as before.

  Good bye

• HP elitebook 2540p does not start after the successful bios update

  Hello people,

  I need your help.

  my hp elitebook 2540p with 2.5 "hhd does not start after a successful bios f.03 to f.24 upgrade done through windows 7.

  When I turn it on the blue light of wifi and power is on but nothing happen.

  I tried to remove the chip from the bios, cmos, hdd, ram, wifi battery... all, but nothing doesn't happen.

  I also tried to start it with the victory + b procedure and win + procedure four arrows so without USB key the caps lock flashing indefinitely but nothing happens, only the fan works quickly with a blue light

  with the USB the system restarts itself every two seconds and I have to remove the USB key.

  I do not know how...

  Thanks for any help.

  Luigi

  all very well now. I used the f.20 rom based on the internet and everything works again.

• XP does not start after the installation of avira. Blue screen: STOP: 0 x 00000024 (0 x 00190203, 0 x 87174270, 0xc0000102, 0x00000000)

  Original title: xp does not start after the installation of avira

  I have a HP Slimline s7410
  XP Home Edition SP3
  I had Norton free with Comcast, but since I have no more Comcast became Norton expired. So I uninstalled Norton and installed the free version of Avira, he scanned the computer and it was clean. I went to reboot and now it does not start.
  I have a cd/dvd drive of work.
  I don't have an XP bootable installation CD

  My system worked well until: I installed the free version of Avira

  Whenever I select one on the XP advanced options options menu start, it goes into a boot loop.
  I turn off the auto reboot system failure although it seems only work once, as the next time he's trying to start up it goes into the boot loop.

  Here's what my BSOD looks like:

  Disable or uninstall any anti-virus, disk defragmentation or backup utilities. Check the configuration of your hard drive and check the updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

  Technical information:
  STOP: 0 X 00000024 (0 X 00190203, 0 X 87174270, 0XC0000102, 0X00000000)

  Any help is greatly appreciated! :)

  My first suggestion is to do a system restore at this time point.

  second suggestion is to keep your external drive connected to the pc at all times.  only detach when necessary.   of course, it would be better to install a second hard drive in the computer instead.   in any case, keep your personal files out of the system disk is a wise thing to do.   You can also download and store files for free on the Microsoft Skydrive site.

  third suggestion is to keep your system set upward through executing a check disk and Defrag at least once a month.   Basically, you can open the Explorer and right-click on the drive letter.  then select Properties, and on the Tools tab, you will have the opportunity to run the disk check.  then reboot and do a Defrag.   where this disk check fails, then you will need to run it to the drive via a bootable cd prompt.

  Interestingly, I don't know if the bootable cd that you made you allows to run the disk check.

  so my suggestion is to do a series of tests using your cd bootable your computer works.  see if you can actually run a chkdsk/r at the moment with them.    If Yes, then if your constant worries are having bad sectors on the hard disk, chkdsk/r will identify and mark so windows will jump on them.    in any case, see if your boot at the moment media can run a check disk at all, and let me know.

  fifth proposal is to install "microsoft security essentials" like your anti virus program.  even if you have run ubantu, it is not likely to have been an infected copy.   anti - are most critical virus for windows and not not so much for ubantu or linux is because windows is a system of world class operations.    the people who make the virus deliberately their engineer for the windows operating system.   If, however, ubantu and linux have been just as popular as Windows, virus engineers would make infections for the o.s. too.     Although they no doubt, attacks are more frequent for the windows os.

• HP DV7-7259nr does not start after the BIOS update

  Hello

  I have a problem with my HP DV7-7259nr laptop, WIN8 running: it does not start after tune recommended to update BIOS and drivers.

  It downloaded all the drivers and started installing at one time, he asked for a reboot, click OK and the BIOS update has begun to load. The process ended successfully and after the reboot that my laptop wouldn't start; everything is black and the cooler is runing.

  I tried:

  -battery disconnected and power - button Power - plugged power again-> NOTHING

  -Windows key + B + Power button--> nothing

  Please help as this is the laptop I use daily in my work.

  Thank you

  If you install the electro mechanical original hard drive in it starts?

  If it has been delivered with a SSD?

  The specifications indicate that an electromechanical drive was part of the specification.

  

  This is where lies the UEFI environment. It is actually on the hard drive.

• Pavilion dm4-1265dx does not start after Windows 7 logo

  My laptop does not start after the "Starting Windows" screen when I try to boot the operating system normally. When I try to run the repair mode from the start nothing happens... I get a blue background image and the pointer of the arrow, but no icons or windows appear.

  I tried the system diagnostic mode by pressing ESC when turning the laptop on and the hard drive test fails every time, showing the following results:

  Test Drive: 1
  INTELLIGENT control: passed
  DST short: failure

  Failure ID: 64RG79-5AP62V-XD6U2K-60RN03
  Product ID: XZ298UA #ABA

  Hard drive 1

  --------------------------------------------------------

  Test drive: FAILURE

  How should I proceed? The laptop is still under warranty, but it was purchased in the United States, and I now live in the Brazil.

  Hello

  You will need to replace the hard drive.

  HP should send you a new drive for free, but in your case is a little complicated as you mentioned it already. Please contact HP tell them about this situation. How to do?
  Click on the link below and choose your country:
  Contact HP worldwide

• FF does not start after upgrading to version 27.0.1

  FF does not start after upgrading to version 27.0.1
  Crash ID: bp-2bc18734-d643-4843-a10f-fd6102140214

  Firefox 27.0.1 is too recent for me to know what unique issues it may have. I will message you a link to download the installer for Firefox 27.0 to see that the inversion or not the problem.

• The browser does not start after you have turned off and turned on the computer

  The browser does not start after you have turned off and turned on the computer. I tried to remove the program entirely (as well as personal preferences), to create a new account, install a different browser versions. All this has not helped. (I have Windows 7). Help, please! Every day I have to reinstall Firefox!

  Hello Nastena, try a clean reinstall, some Firefox issues can be resolved by performing a clean reinstall. This means that you Remove Firefox program files and then reinstall Firefox. Please follow these steps:

  Note: You can print these steps or consult them in another browser.

  1. Download the latest version of Firefox from http://www.mozilla.org office and save the installer to your computer.
  2. Once the download is complete, close all Firefox Windows (click on quit in the file menu or Firefox).
  3. Remove the Firefox installation folder, which is located in one of these locations, by default:
     • Windows:
       • C:\Program Files\Mozilla Firefox
       • C:\Program Files (x 86) \Mozilla Firefox
     • Mac: Delete Firefox in the Applications folder.
     • Linux: If you have installed Firefox with the distribution-based package manager, you must use the same way to uninstall: see Install Firefox on Linux. If you have downloaded and installed the binary package from the Firefox download page, simply remove the folder firefox in your home directory.
  4. Now, go ahead and reinstall Firefox:
     1. Double-click on the downloaded Setup file and go through the steps in the installation wizard.
     2. Once the wizard is completed, click to open Firefox directly after clicking the Finish button.

  Please report back to see if this helped you!

  • Also check if your antivirus or other access security software (firewall, antispyware etc.) blocks firefox.

  Thank you

• Two iMacs does not start after the 10.11.4 update.

  Two iMacs does not start after the 10.11.4 update.  Progress bar starts moving and then text appears on the black screen saying unexpected sigkill to launchd.  He then gets stuck in a loop trying to start.  Tried to reset the SMC and LANDAU.  Without success.  Started in recovery mode and ran disk utility.  Discs said OK.  Chose to reinstall OS X from the list of options in the recovery mode (assuming it would be 10.11.4).)  Installation is finished but still once does not start.  Reinstalled on 10.11.0 successfully from a USB key and downloaded the 10.11.4 combo updater.  Installation seems to work, but once again, the macs will not start.  Same 'unexpected launchd sigkill' error.  A mac is now back working properly with 10.11.3 the other will be shortly.  Is there a problem with the accession?  Our COMPUTER support use Munki to get updates from one day to the next.  Fortunately, we were able to stop it before the other 20 or if Mac had the same problem.

  More information: two bricks iMacs were late 2013 models.  A 21 "and a 27.  We have just updated a test iMac which was a late model 2012 using the 10.11.4 combo updater.

• ITunes does not start after the installation of Windows 10

  ITunes does not start after the installation of Windows 10, 1511 version (OS Build 10586.164). ITunes version 12.3.2.35, 6 GB RAM, Intel i3 @3.3 GHz. Itunes and Ipodserver module will run by Manager jobs, but Itunes does not open. iTunes starts in SafeMode as explained in the link below (hold SHIFT and control on your keyboard while you open iTunes).

  Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

  Solution, according to this link, is:

  If the problem does not occur in Mode safe, remove any third party plug-ins iTunes: solving problems with third party plug-ins - Support Apple iTunes but the link has been archived, and I can't find any plug-ins installed iTunes. Any other ideas?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• Re: Smoker L30-10 X PSL33E does not start after upgrading RAM

  Hello

  I have a problem with my laptop.
  It has 1024 MB of RAM (2 x 512), but it wasn't enough, so I decided to update to 2048 MB (2 x 1024).

  I bought two modules and my computer does not start after changing them.
  It was only a screen black (same BIOS has not started). I tried another combination of installation of memory modules RAM.
  2 x 1024 - did not work
  1 x 1024 - did not work
  1 x 1024 + 1 x 512 - working but not properly.

  BIOS find that I only 896 MB (1024-128 for the video card)
  I said OK. Let's see what will show windows. He was also 896 MB.
  I launched CPU - Z and it shows that the total size of memory is 1536 MB (medium detect both modules).
  I found that CPU - Z detect 1 module 1 024 MB and 512 MB secondary, but the BIOS detect only 1024 MB 1536. How is that possible?

  I have fought, is that my BIOS is old, then I update the toshiba Web site form most recent version, but the problem persists.
  Please someboy help me and tell what to do.

  PS. the Modules are new and work correctly.
  They have been tested.

  Hello

  Have you used two identical RAM modules?

  What kind of modules did you use?

  In my view, that the problem is related to the new, inserted modules.
  There must be something wrong with the modules or modules are not completely compatible if the laptop can not boot after installation.

  According to a few pages of the book handles the DDR2 533 MHz (PC2-4200) 200-PIN SODIMM modules.

  Did you use these modules?