Similar Questions

• Access to the web server that is running in VMWare Fusion (Windows 7)

  Hello:

  I have an old asp application running on the Windows IIS7 server running in VMWare Fusion on my Macbook. It works very well if access http://localhost side windows in Fusion.  How do you get it from other computers on the network? I usually not done anything with access to the network on the windows side. I tried to use the same IP Mac address is visible, which is 192.168.0.xxx, that does not work. On the Windows operating system side it has the IP address 192.168.216.xxx, I think it's just a fake to connect with the Macbook side of things.

  What URL to use? VMWare Fusion additional requirements?

  Thank you!

  If you value Network Adapter to the Virtual Machine Bridged then use either DHCP or assign a proper IP address provision that is beyond the scope of the address Pool IP DHCP from the router to the network card in the Windows Virtual Machine, you can reach then the virtual machine just like any other physical local network Machine by using its IP address example: http://192.168.0.10

  If you cannot use Bridged so you use NAT with Port Forwarding.  To enable Port Forwarding on VMnet8, change you the [incomingtcp] section in Library/Preferences/VMware Fusion/vmnet8/nat.conf by the example shown in the config file.  Do it with the stop the Virtual Machine, not suspended, and VMware Fusion closed.

• How can I access the web server by using sound!

  I have a LAN with the address 192.168.2.0 255.255.255.0.My internal address is 192.168.0.22, it map to the 61.154.9.64 address (public). How can my internal hosts access to the web server using sound!

  DNAT (Destination NAT) comes to mind - click here to see if it helps:

  http://www.Cisco.com/warp/public/110/alias.html

  Jay

• External HTTP > internal to the web server

  Hello

  I have a router ADSL with a public IP assigned, preforming NAT. This leads to a 506th PIX which leads to a Web server. The entire interior of the ADSL is on private IP addresses.

  I want to allow external users access to the Web server on port 80.

  I inwardly and outwardly put up ICMP connectivity (for testing only) and it works correctly.

  I created a virtual server on the ADSL router that forwards port 80 traffic to the external interface of the web server. It has worked successfully for half an hour and then something in the config changed PIX and it no longer works. Here is my config PIX

  SH conf

  : Saved

  : Written by xxxxx at 08:41:10.001 NZST Thursday, October 13, 2005

  6.3 (4) version PIX

  interface ethernet0 car

  Auto interface ethernet1

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable the encrypted password xxxxxxxx

  xxxxxxxxx encrypted passwd

  hostname PIX

  domain ciscopix.com

  clock timezone GMT

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  icmp protocol error correction

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  no names

  name 192.168.5.3 PixExt

  name PixInt 192.168.6.1

  name 192.168.5.1 ADSLInt

  name 192.168.6.2 WebExt

  acl1 list access permit icmp any any echo response

  access-list acl1 allow icmp all once exceed

  access-list icmp permitted acl1 everything all inaccessible

  acl1 list access permit tcp any host 192.168.6.2 eq www

  pager lines 22

  opening of session

  timestamp of the record

  Record being buffered memory errors

  logging trap notifications

  ICMP allow all outside

  ICMP allow any inside

  Outside 1500 MTU

  Within 1500 MTU

  external IP 192.168.5.3 255.255.255.0

  IP address inside 192.168.6.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  location of PDM 192.168.6.2 255.255.255.255 inside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  NAT (inside) 0 192.168.6.0 255.255.255.0 0 0

  Access-group acl1 in external interface

  Route outside 0.0.0.0 0.0.0.0 192.168.5.1 1

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  http 192.168.6.2 255.255.255.255 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd lease 3600

  dhcpd ping_timeout 750

  xxxxx xxxxxxx privilege 15 encrypted password username

  Terminal width 80

  Cryptochecksum:xxxx

  DMZInside (config) # route sh

  outside 0.0.0.0 0.0.0.0 192.168.5.1 1 ANOTHER static

  outside 192.168.5.0 255.255.255.0 192.168.5.3 1 static CONNECTION

  inside 192.168.6.0 255.255.255.0 192.168.6.1 1 static CONNECTION

  DMZInside (config) #.

  No idea where I have gone wrong?

  Thank you.

  you are missing this statement

  public static 192.168.6.2 (Interior, exterior) 192.168.6.2

  Thank you

  Nadeem

• Upgrading to 4 Fusion and now I can't access the web server on my Mac host

  I am running OS x 10.6.8 and I'm hosting a virtual machine running windows XP, using NAT Networking. I have a web server running on the mac I need to access from the hosted virtual machine. I used to be able to just use the IP address of the gateway in the virtual machine for the web server, but it doesn't seem to work. If I set the external IP address of the mac it seems to work, but I don't have a static IP address, so it is a pain to update every hour.
  
  Any help would be appreciated!
  
  Thank you

  Although in some cases, the IP address of the gateway works, nevertheless IMO that is a misuse and should use the address IP of VMware NAT Virtual Ethernet adapter IP address the host not IP address of gateway.

  If in a Terminal, run the following command:

  ifconfig | grep -A 3 vmnet8
  

  Then use the address after "inet" IP said at the exit.

  Example on my system:

  Last login: Mon Jan 16 12:43:00 on ttys000
  Computer:~ WKZ$ ifconfig | grep -A 3 vmnet8
  vmnet8: flags=8863 mtu 1500
      ether 00:50:56:c0:00:08
      inet 172.16.198.1 netmask 0xffffff00 broadcast 172.16.198.255
  Computer:~ WKZ$
  

  So I use 172.16.198.1 of the prompt or use the host name of the Mac (without the .local) after the addition of 172.16.198.1 and the hostname of the Mac to the guest hosts file.

  Post edited by: WoodyZ - posted: January 16, 2012 12:52

• cant access built-in web server on HP6940 due to the new router

  New router has IP 192.168.2.1

  Changed Deskjet 6940 IP 192.168.2.60 and it turned off... fails to 192.168.1.3 to the power upward and can not find network using IP or hostname

  Hoe can I access the Web server integrated to change the IP address without having to reinstall everything... seem to have misplaced the installation CD

  Thank you

  Chris

  Solved the problem of the IP address as follows:

  Connected a spare laptop router.

  Changed router IP to 192.168.1.1

  Printer plugged into router

  Could then access printer Web Server to 192.168.1.3

  Changed printer IP for 192.168.2.6

  Printer is now accessible on the network

• Difference in the gateway.properties file when you access of PIA and the opening of the PSIGW folder in the domain of the web server

  Hello

  When I open the file gateway.properties by ITTO's domain\application\peoplesoft\psigw web server directory, I see certain values that are not the same, when I open the file gateway.properties of PIA by navigating to Peopletools-> Integration Broker - > gateway configuration-> gateway.properties file. I tried to clear the web server cache, restart the web server. Even then, I see quite different values of these two places. If I do any change in one of the two places, his not reflecting only with access to another place.

  Could someone delete the following point?

  -I think there is only a file gateway.properties under the web server's domain. When access us the PIA file, wherever to be included in?

  -Is the file stored somewhere in the database as well? where it recovers when PIA accesed?

  -The two are always in sync from different modes?

  -How to synchronize these two?

  Thank you

  Dinkar

  There is only one file per domain. It is read by a web service call when you view it in the PIA. This allows you to edit files from another server. The only time they will be different, that is if the URL of your entry point to a server other than the local server.

  If the URL of your entry points to the same server as your local file, then the only advantage to use the PIA to modify the file (except easy access), it is that sometimes it will update the properties in memory. Change the file in the file system requires to restart the web server for the properties to reload in memory.

• Unable to connect to port 80 on the web server on host Ubuntu guest

  I have a very strange problem. I've been running a VM of 14.04 Ubuntu on my MBP under VMware Fusion for some time. I have re-installed Yosemite during the weekend for a clean installation trying to solve some of the problems I had. I now have my Ubuntu VM up and running. All right, except that I can't hit the web server on the virtual machine.

  I can access the virtual machine in a variety of different ways!

  • Ping: I can ping
  • SSH: I can ssh in
  • psql: I can connect to the database remotely via port 5432
  • NFS: can I get the files of the virtual machine files on my hard drive
  • Tomcat: I can access my web application directly through Tomcat on port 8080

  When I do a scan of port of the virtual machine, I get this:

  Port scan started...

  Host port scan: 10.39.186.13

  Open TCP Port: 22 ssh

  Open TCP Port: 111 sunrpc

  Open TCP Port: 389 ldap

  Open TCP Port: 2049 nfsd

  Open TCP Port: 5001 commplex-link

  Open TCP Port: 5432 postgresql

  Open TCP Port: 8000 irdmi

  Open TCP Port: 8080 http-alt

  Open TCP Port: 8104

  Open TCP Port: 37805

  Open TCP Port: 41301

  Open TCP Port: 42060

  Open TCP Port: 55224

  Open TCP Port: 60974

  Port scan has completed...

  Port 80 is not even there. The virtual machine itself, I can access the site via port 80:

  wget xnat@xnatdev:~$ http://xnatdev.wurstworks.com

  -2015-06-22 11:20:50- http://xnatdev.wurstworks.com/

  Resolution xnatdev.wurstworks.com (xnatdev.wurstworks.com)... 127.0.0.1

  Connection to xnatdev.wurstworks.com (xnatdev.wurstworks.com) | 127.0.0.1 |: 80... connected.

  Query HTTP sent, awaiting response... 302 Found

  Location: http://xnatdev.wurstworks.com/app/template/login.VM;JSESSIONID=18A2C3A7C7AB6A63F39F7AC49E54FCD4 [next]

  -2015-06-22 11:20:50- http://xnatdev.wurstworks.com/app/template/login.VM;JSESSIONID=18A2C3A7C7AB6A63F39F7AC49E54FCD4

  Reuse an existing connection to xnatdev.wurstworks.com:80.

  Query HTTP sent, awaiting response... 200 OK

  Length: unspecified [text/html]

  Record on: 'index.html '.

  [ <=>                                                                                         ] 12,818      --.-K/s   in 0.001s

  2015-06-22 11:20:50 (11.2 MB/s) - 'index.html' saved [12818]

  But the host OS, I get this:

  wget rherrick@Aerys:~$ http://xnatdev.wurstworks.com

  -2015-06-22 11:21:50- http://xnatdev.wurstworks.com/

  Resolving xnatdev.wurstworks.com... 10.39.186.13

  Connection to xnatdev.wurstworks.com | 10.39.186.13 |: 80... has failed: connection refused.

  I tried switching between NAT and open networking (I know that I had to work with NAT before, but I'm willing to try anything at this point).

  I'm on OS X 10.10.3 and the most recent, and VMware Fusion 7.1.2. Any ideas on how to get this working would be greatly appreciated!

  OK, got it market. The issue was the listen directive in configuring nginx for connecting Tomcat. I'd put it domain name FULL and port 80 on the server, but something I did is the determination of the FULL domain to 127.0.0.1 instead of the IP DHCP-published name. If this does not work because the incoming request has been the full domain name of host configured in my/etc/hosts, OS, then nginx not pair together configuring nginx for the domain since listening has been screwed up.

• Not possible to activate the scripts on the Web server

  Hello

  I would like to create a page .html for Web with a bit of scripting ESP included - Services because now I understand just this:

  <% for (i=0; i<3; i++) {
    ...some text...
   } %>

  According to this document NOR, I first need to enable scripting:

  To use the script with a Web service, you must enable the feature on the Web of LabVIEW server. In LabVIEW, select the script on the Web Server: Configuration page in the dialog box Options to enable the use of scripts on the Web server.

  I activated the Web server and it works OK. But there is nothing called "Scripting" in the configuration page - and the script is executed (the code is just printed in the form of simple text).

  Anyone know how to activate the ESP script?

  Version: LV 2012.

  Best regards, Jan

  Hi Jan,

  In fact, you use the ESP file instead of a static HTML file.  For example, if we had the static html file:

  Hello world

  This file can be located at something like /MyWebService/HelloWorld.html.

  If I then do something like have a page to say "Hello, Jan" or "Hello, Mark" I could use ESP.  In this case, your code might look like:

  <>

  var xname = form ['name'];

  %>

  Hello, @@xname

  The URL of such a web method is perhaps something like jan/MyWebService/Hellovar/Jan where Jan string literal passed to the terminal of a web method that can resemble

  

  In this example, the string "Jan" is passed to the terminal of the value of the VI.  What implementation of the Web method in the spec to build his signature might look like in /Hellovar /: value.

  So, back to your original question.  You embed not ESP breast and the HTML document.  Instead, you embed HTML inside a document of ESP and the rendering of the document in HTML format when accessing the URL of the Web method.  While the paper you mentioned earlier has an example project in that you can use as a reference

• How to allow the clean-up actions to be taken by a reentrant clone before he is killed, seen through the web server, through a narrow browser?

  Here's a question I'll get lucky with.  I have a VI, set to be reentrant, broadcast via the web server.  The main instance of the VI is never worked with: it's a clone whenever someone accesses the correct URL, and the user interacts with the newly created clone (never the main forum).  A clone is able to configure and calling instrument VI when good IDs are entered, which translates to browser popups that are controllable on the end of the user (even if only one user ever does both. To clarify, many clones can be opened simultaneously for connection purposes, but that a user never interacts with the instruments that are not themselves reentrant).

  If the user clicks on my Logout button in their browser, it is trivial to close these instruments other, independent and properly clean.  But if the user simply click on the red X in their browser, it is non-stop and the instruments that the clone called stay open on the server, when they close.

  My experience so far:

  No close panel? event seems to be triggered in the clone.  The clone simply cease to be.

  The remote_panel_connections property doesn't seem to work properly in this case (I have not had luck so far), since it is possible that more than a clone to be active and that the main parent who is spawning clones stays running, but is not interacted with in some way.

  What I need:

  One way for the clone of VI recognize that the user has closed his browser and communicate that it closes all the assets of VI before ending.

  --------------

  I would like to avoid forcing the instruments that the clone call to constantly query to see if the VI clone is present on the network.  If there is no other solution, but this, I would appreciate a suggestion as to the intensive way less code and resources to implement this type of interrogation, as the instruments are really designed to be totally independent after they are called, rather than under vi.

  Thanks for all comments, let me know if you need more information.

  MTdev wrote:

  One way for the clone of VI recognize that the user has closed his browser and communicate that it closes all the assets of VI before ending.

  When a VI stops running, any reference as a queue is also cancelled.  You can make use of this fact.  If your original clone VI could launch a second reentrant VI, which remains active, you could channel all communications to the instruments via VI second using a queue created in the first.  When the first VI disappears, it will trigger an error waiting waiting VI in the second (no vote office is involved).  The second VI can take all the necessary measures.

• run the Web server in vmware

  Hello
  I run the Web server in the os(xp pro) host and now I want to run the Web server in the guest operating system
  I put things in the host operating system, follow
  router setting page (shared ip settings page)
  1 DHCP using OFF
  2 DMZ host server using on 192.168.10.201
  3. setting of virtual server 192.168.10.201 port TCP port internal external port 81 81
  TCP/IP
  1 use the following IP 192.168.10.201
  2 gateway 192.168.10.1
  3. the DNS settings of
  4. on the Advanced tab > Internet connection sharing > VMware Network Adapter VMnet 8
  for now, when someone tries to access my WAN IP then page host server is apear (from external network)
  If I stop server Web host then cannot access my WAN IP

  and in VMware, I put the (Windows XP Pro)
  TCP/IP configuration
  1 use the following IP 192.168.88.201
  2. default gateway 192.168.88.2
  3. the DNS settings of
  4. click the guest OS tab and click Edit > virtual network editor > NAT VMnet host is VMnet8
  5. setting NAT > Port forwarding > Add >: host port 81 machine virtual ip address 192.168.88.201 port 81
  and at the moment access to 192.168.88.201 in the guest operating system is ok the page is apear
  but nothing is apear when try and access my WAN IP external network and if I start it the host Web server then the host page is apear that im is not the intention of
  How can I make the Web server of the guest to access other networks operating system?
  in the guest operating system, I can access Web server of the customer by access 192.168.10.201
  but I can't access Web server of the client by typing host operating system access the 192.168.10.201
  any ideas? My version of vmware's vmware-workstation - 6.5.2 for windows

  Hi Teayun,

  Thanks for visiting the site of the community of Microsoft Windows XP. The question you have posted is related to VMware and would be better suited to the VMware or TechNet community. Please visit the link below to find a community that will support what ask you

  http://www.VMware.com/support/
  http://TechNet.Microsoft.com/en-us/default.aspx Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• I can\ to connect to the web server integrated on my D7460?

  Hello

  I had some problems with my Photosmart D7460 printer and resolved (for now) most of them.

  Except that I can't connect to the built-in web server. Also, I do not get a response when I try and ping the printer.

  Giving to think I have problems of network with the exception that I can print to this printer... Well well, from most of the computers on the network, but that's another story.

  I checked what the said road IP address he gave to the printer.

  Any suggestions would be welcome.

  OK, I seem to have solved the problem.

  I'm not sure that bit of material, it was causing the problem but it seems to come form tries to use "WPA & WPA2" parameters (BT Home Hub 3.0) wireless access point.

  Who having spent 'WPA only' I can now ping, print and connect to the web server.

• N3048 access to the Web Interface without OOB

  I recently had our switch replaced by RMA and have access to the web interface via oob. I'm not sure how to access ports and other subnets and want to access the web interface of the server room outside. It's probably something very obvious, but I don't have the original switch to check the configuration. Any help would be appreciated. Thank you.

  You can use in-band or oob access to administration from inside or outside the server room.  The port of oob is a completely separate network used for management only, but you can also use a port in the Strip management.  By default, VLAN 1 is usually used in the Strip to transport of management traffic.  If you set an IP address on VLAN 1 you should also be able to manage from this IP address.  Measures would be to define the IP address on VLAN 1, ping ping to test connectivity, remote and then use your browser to connect to the web INTERFACE.  You should be able to use the same username/password that was used for the oob port.  Without a set of name of user and password, the web INTERFACE will not allow the session.

  B

• NAT problem for the Web server

  
  I have configured the new cisco asa 5512. I can't access our Web site from outside. We host our internal site
  This is how I configured. Internal IP of the Web server is 192.168.1.19
  in the following config, I changed my public ip of the webserver to 99.99.99.99
  Can someone help me with this.
   
  the Web server object network
  Home 192.168.1.19
  NAT 99.99.99.99 static (inside, outside)
  NAT (inside, outside) interface static tcp www www service
  outside_access_in tcp allowed access list any object Webserver eq www
  Access-group outside_access_in in interface outside

  It is not open by default, but you already enabled.

  Remember that all you need is a translation you have:

   object network Webserver host 192.168.1.19 nat (inside,outside) static 99.99.99.99

  And the list of access allowing access to desired ports:

   access-list outside_access_in permit tcp any object Webserver eq www access-list outside_access_in permit tcp any object Webserver eq 8080 access-group outside_access_in in interface outside 

• PIX 501 problems with the web server internal.

  I want to open for my internal Web server, so it can be accessed from outside and I read about it here and how to do it and I do what I think of his right, but I can´t operate.

  Now I just tried to open the http port standard 80 but later I want to open a specific port and also use SSL on the web server for added security.

  Then I would like my setup now get help and also how to do when using other ports and SSL later.

  Thanks Thomas!

  6.3 (1) version PIX

  interface ethernet0 10baset

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  alfta hostname

  domain ciscopix.com

  names of

  name 192.168.1.16 TerminalPC

  name 192.168.3.0 Lager

  permit 192.168.1.0 ip access list inside_nat0_outbound 255.255.255.0 192.168.2.0 255.255.255.0

  permit 192.168.1.0 ip access list inside_nat0_outbound 255.255.255.0 255.255.255.0 Lager

  permit 192.168.1.0 ip access list outside_cryptomap_20 255.255.255.0 192.168.2.0 255.255.255.0

  permit 192.168.1.0 ip access list outside_cryptomap_40 255.255.255.0 255.255.255.0 Lager

  outside_cryptomap_60 ip access list allow

  192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  outside_access_in tcp allowed access list all eq www

  host 62.108.197.90 eq www

  IP outdoor 62.108.197.90 255.255.255.192

  IP address inside 192.168.1.254 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  location of PDM 62.108.197.10 255.255.255.255 outside

  location of PDM 62.108.197.11 255.255.255.255 outside

  location of PDM 192.168.1.0 255.255.255.255 inside

  location of PDM TerminalPC 255.255.255.255 inside

  location of PDM 192.168.2.0 255.255.255.0 outside

  location of PDM Lager 255.255.255.0 outside

  location of PDM 192.168.2.0 255.255.255.0 inside

  location of PDM 62.108.197.137 255.255.255.255 outside

  location of PDM 62.108.197.137 255.255.255.255 inside

  location of PDM 195.67.210.72 255.255.255.255 outside

  location of PDM 62.108.197.90 255.255.255.255 inside

  PDM logging 100 information

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  static (inside, outside) tcp 62.108.197.90 www TerminalPC www netmask 255.255.255.255 0 0

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 62.108.197.65 1

  Enable http server

  http 62.108.197.10 255.255.255.255 outside

  http 62.108.197.11 255.255.255.255 outside

  http 195.67.210.72 255.255.255.255 outside

  http 192.168.1.0 255.255.255.0 inside

  http 62.108.197.137 255.255.255.255 inside

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set esp strong - esp-sha-hmac

  outside_map 20 ipsec-isakmp crypto map

  card crypto outside_map 20 match address outside_cryptomap_20

  peer set card crypto outside_map 20 195.198.46.88

  outside_map card crypto 20 the transform-set ESP-DES-MD5 value

  outside_map 40 ipsec-isakmp crypto map

  card crypto outside_map 40 correspondence address outside_cryptomap_40

  peer set card crypto outside_map 40 62.108.197.137

  outside_map card crypto 40 the transform-set ESP-DES-MD5 value

  outside_map 60 ipsec-isakmp crypto map

  card crypto outside_map 60 match address outside_cryptomap_60

  peer set card crypto outside_map 60 195.198.46.88

  card crypto outside_map 60 the transform-set ESP-DES-MD5 value

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP key * address 62.108.197.137 netmask 255.255.255.255

  ISAKMP key * address 195.198.46.88 netmask 255.255.255.255

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 sha hash

  10 1 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  part of pre authentication ISAKMP policy 20

  encryption of ISAKMP policy 20

  ISAKMP policy 20 md5 hash

  20 2 ISAKMP policy group

  ISAKMP duration strategy of life 20 86400

  Telnet 192.168.1.0 255.255.255.255 inside

  Get out your ACL - access-list outside_access_in permit tcp any host 62.108.197.90 eq www

  And a new application:

  outside_access_in list access permit tcp any host 62.108.197.90 eq www

  Access-group outside_access_in in interface outside

  * You have the group-access above on your original configuration message, BUT not on the above post.

  Don't forget to issue clear xlate after the change and also record with write mem.

  Try to do this in the pix CLI instead of using PDM.

  Hope this helps and let me know how you go.

  Jay