vMotion on ESXi5 is not using multiple NIC

Similar Questions

• use of multiple vmdk or do not use multiple vmdk...

  Hi all, we are trying to achieve a standard for disk management.  The question is whether it is preferable to use a separate vmdk for each drive letter which is to be awarded on a given virtual machine or is it better that we use a vmdk and divide accordingly.  thoughts?  I know there is a logic in keeping data on a vmdk and trans of the log files for database servers and bkup on a separate vmdk but the same logic can be applied to a regular application server?  for example, if I have a file used vmdk for the system partition (c drive) and then I need four more disks (d, e, f, g), these four discs are all on a vmdk or each of them we their own vmdk?

  Separate the individual VMDK partitions. This will make it less simple to extend individual readers and it costs you nothing.

  Never been a fan of HDs partitioning in physics systems Windows and Vmware facilitates does no homework. You don't have not to worry about small problems that can happen, next to the performance for which you have already noticed.

• Best use of multiple NICS (collaborate with VIRTUAL networks or physcially separated)

  Set up my new production environment vSphere and trying to figure out the best way to set up the network.  I have pictures to illustrate, but the basic question is:

  1. use all NICS in a pool and VLANS to separate traffic - or -

  2 devote some physical nic to only certain things (VMotion, FT etc..)

  We use Dell R710 2 servers with 6 NIC of each.

  Our SAN is connected via zFCP iSCSI, see you in the group is therefore only for failover of emergency if environmental FC had to leave for some reason any.

  Please let me know which design you think would be the best.

  Thank you

  Michael

  Hello

  Everyone says to separate the service of the VMnetwork console.  If I can separate the traffic of service with one console vlan why separate physically?  If something happens to the service console connection disconnects but my machines always communicate then I would have trouble.  Why not make sure that if the network paths are for machines that I can control the server VM?

  Your VMNetwork is one of network environments more hostile within the vNetwork as its arbitrariness and a point of attack if someone breaks into a virtual machine. If you have the virtualization management network attached to your VMNetwork is on, there is a VERY good chance that the pirate VM now will be used to launch an attack against the network of virtualization management. Given the current set of attacks there is a VERY good chance of success. For security reasons, you want your management network virtualization to be separated and protected by a firewall of any other physical and virtual network. Ideally on its own switches with output physical switch VLAN in use. However if you use VLAN physical switch then you put your trust in these spending patterns, so you want to increase your monitoring of these switches.

  Since the original post, I combined the iSCSI traffic because it is a failover of emergency only where my zFCP hardware has a problem.  The iSCSI link rarely go to never get used and I didn't spend 2 physical network cards to something that would almost never be used.

  You want to spend 2 links for iSCSI, if you still do not have a failover, you can the bandwidth and redundancy. Consider all the links of storage redundancy.

  Let me know what you think on the service console.

  When you use VLANS in the vNetwork you are automatically protected against most known layer 2 attacks, but in the pNetwork you are confident that your switch configurations you will protect. These configurations have been known to change and not necessarily for the better. Some say, it must break so for that to happen, but 1 problem of configuration and your SC is now attacked. Remember, once the virtualization management networks can be attacked they can probably be broken. I know a pen-Tester, which can do that in a very short time, and they will have your virtual environment.

  Protect the machine from service/management console, Client vSphere, vCenter servers as if they were gold, access to them implies access to almost everything. That's why VMware strongly recommends that you create another network of virtualization management a firewall of all systems on your system. That within this firewall that place you jump machines that run all vSphere SDK and vSphere client and that you use something like RDP to access these tools without their execution through your firewall. Make this thing increases the security of your global virtual environment of giant protecting your investment in the current batch of management network attacks. VLANs are not a security tool, they are a tool of separation of network based on the pNetwork is correctly configured, maintained and checked. VLAN security is based on the confidence in your pSwitches not something that is authoritative.

  Best regards
  Edward L. Haletky VMware communities user moderator, VMware vExpert 2009, 2010

  Now available: url = http://www.astroarch.com/wiki/index.php/VMware_Virtual_Infrastructure_Security'VMware vSphere (TM) and Virtual Infrastructure Security' [/ URL]

  Also available url = http://www.astroarch.com/wiki/index.php/VMWare_ESX_Server_in_the_Enterprise"VMWare ESX Server in the enterprise" [url]

  Blogs: url = http://www.virtualizationpractice.comvirtualization practice [/ URL] | URL = http://www.astroarch.com/blog Blue Gears [url] | URL = http://itknowledgeexchange.techtarget.com/virtualization-pro/ TechTarget [url] | URL = http://www.networkworld.com/community/haletky Global network [url]

  Podcast: url = http://www.astroarch.com/wiki/index.php/Virtualization_Security_Round_Table_Podcastvirtualization security Table round Podcast [url] | Twitter: url = http://www.twitter.com/TexiwillTexiwll [/ URL]

• ESX host will not use VMotion

  Hi all

  I have a question maybe someone can help.

  I installed two new ESX hosts in their own cluster, managed by a single data center environment.

  After the installation and updates, adding them to the Cluster environment and adding new licenses to the license server VC.

  I have one of the two ESX host who won't use VMotion. Everything is allowed as should be. But in the section of the Add On to the Configuration of the license, I see the following:

  VMware DRS Licensed for 2 cpu

  VirtualCenter for ESX Server Licensed agent for 2 cpu

  VMotion will not used

  VMware Consolidated Backup for 2 cpu license

  VMware HA under license for 2 cpu

  Additional details:

  Both servers in the cluster are identical hardware profiles: Intel 3.2Gig Xeon, 2 cavities 4 hearts, no HT.

  32Gig of RAM, (Proliant DL380 G5)

  The two servers connected to the SAN via Fibre Chanel Switch, redundant.

  Concert NIC ((VMNic 0 (Console 1), VMNic 1 (Standby adapter), VMNic 2 (Console 2) (the Virtual Machine Network), (VMkernel), (ports of vSwitch 56 none VLAN not defined) VMNic 3 (Standby adapter)).)

  No errors in the Logs of license, the Console message, etc. Everything seems in good health with no update needed.

  Both servers see the unique data store, created on the same SAN which it connects through the switch channel.

  VMFS 3.31.  Unique data store with several extensions (8 in total, the creation of a size of 15 to storage).

  Any ideas?

  All my other hosts using VMotion, but it does not work and there is no difference in configuration, I know.

  Thank you

  • FPTHREE

  Some of the most common problems that cause problems VMotion - have you enabled for VMotion vmkernel port? VMkernel ports on the same segments of entwork?

  Can you provide the ip addresses for your vmkernel enabled for vmotion -

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• Should we include the NIC do not use during P2V?

  There are 2 NIC cards in a physical machine, but only one is used.

  During P2V, should we include both of them and remove one not in use on a virtual machine?  It is because we can choose the bad NIC card if we just choose a NIC card during the P2V process.

  Your opinion is requested.

  Hello

  When you perform a P2V conversion, try to remove all the devices that you do not use from the server.  This is also your chance to allocate hardware resources such as CPU or memory more or less, or adjust the allocated disk space.

  When the conversion is completed, you will need to reconfigure the network settings, so it is not really important which NIC you remove server.

  Best wishes / Saludos

  -

• Nested with 2 management cards workstation + ESXi5.5 = not to ping requests

  Hello community,

  I recently stumbled upon a bug (?) strange:

  I needed to install several 1331820 ESXi5.5 in my computer and noticed that the management interfaces are not to ping/accessible queries if more than one NETWORK adapter is used for the management network. As soon as I remove/disconnect ping NIC begins work and the server is accessible.

  Have not tested multiple ESX versions yet but Workstation 10/09/11 suffers from this.

  Yet several descriptions of this question, but not solutions. A suggested workaround has been upgrading manual driver interface NETWORK of E1000 vmxnet3 but nothing is in my case.

  Someone has any idea how to solve this problem?

  The cause was found to be using linked clones.

  I reinstalled all my guests individually and separately, do not use any cloning and they work like a charm.

• Best network design... Need advice on the best use of NIC

  I'm new to the concept of Distributed Switch so I need advice.

  Our current environment is the result of a vCenter 4.1 and ESXi 4.1 Enterprise Plus, but we are just using the standard vSwitch (1 for vMotion/Console and 1 for virtual machines).  When the distributed switch came out, we were warned that a vDSwitch could cause us problems if the server vCenter or database is down.  We could not connect directly to the host and make network changes because the vDSwitch is set in the database.  That's why we stayed with the Standard vSwitch only.

  Our farm is quite small, only 5 hosts but we run around 100 mV in this regard.

  We use currently servers HP DL385 G7, which have 4 cards integrated network, and we have a map of installed NETWORK 4 port card.

  I use the NETWORK 4 EtherChannel ports and trunk card to our virtual machines.

  I am currently using only 1 network card integrated for vMotion and 1 for the Service Console and they all have two of the other defined as secondary.

  This configuration has worked very well for us, but I realize that the latest version of ESXi has some new features that we could use.

  NEW CONFIGURATION

  I'll put up a new vCenter 5 and ESXi 5 environment and I am considering using the switch distributed instead of the usual vSwitch we use.  I'm also eager to take advantage of the multiple NIC vMotion.  All our cards are 10/100/1000 MB capable... No. 10 GigE.

  I think... use that map 4 NETWORK ports for my EtherChannel/trunk for just as our virtual machine before, but this would be set to vDSwitch1

  The mixture of my 4 other integrated ports, it's causing me grief.  Should they be on a standard vSwitch or vDSwitch?  Use 2 ports for vMotion and 2 for the Console?  I really thought to use 3 ports for vMotion and 1 Console port.  I could put the Console port to use one of the vMotion ports such as adapter of standby is... I'm so confused freaking!

  Any recommendations on how I should put up?

  Hello

  Given that you can't split your vmnic for each vSwitch I would recommend either keep configuration simular with the knoweldge if a whole nic fails, you will take a failure or as autumn has already been mentioned on 'Origin Port ID'. Lets do this out and give a little better example

  Current configuration

  vSwitch0

  VMNIC0 - NETWORK interface integrated - Service Console

  VMNIC1-Onboard NIC - VMotion (different IP or VLAN?)

  VMNIC2-Onboard NIC - VMotion (different IP or VLAN?)

  VMNIC3 - NETWORK interface integrated - VMotion (eve of Console of Service) (different IP or VLAN?)

  vSwitch1

  VMNIC4 - extension PCI NIC - Etherchannel trunk - PortGroup - VMNET

  Extension VMNIC5 - PCI NIC Etherchannel trunk-PortGroup - VMNET

  Extension VMNIC6 - PCI NIC Etherchannel trunk-PortGroup - VMNET

  Extension VMNIC7 - PCI NIC Etherchannel trunk-PortGroup - VMNET

  Now, to captured to eliminate any single point of failure that you could do is break your Etherchannel trunk and back this vSwitch from Port ID and Setup VMNIC2, VMNIC3, VMNIC4, VMNIC5 as vSwitch1 for your VMNET. Then the cable to multiple switches eliminate any single point of faiulre. If your standard configuration would look like this

  vSwitch0

  VMNIC0 - on - Board Service Console

  VMNIC1 - Board - Vmotion

  VMNIC6 - extension PCI NIC - Vmotion

  VMNIC7 - extension PCI NIC - Vmotion (standby Service Console)

  vSwitch1

  VMNIC2 - VMNET

  VMNIC3 - VMNET

  VMNIC4 - VMNET

  VMNIC5 - VMNET

  So to finish any request for psyhical nics on this particular configuration the Port ID of origin essentially around robins. If during your first VM is online it will be use VMNIC2 and nic forever, until a failure, in which case he will grab the next nic online. When your second VM is online it will use VMNIC3 forever, until a failure and so on. This still will give you around the same way through to as far as networking is concerned. However if you are attached to the trunk, etherchannel 4 GB and can obsorb a failure in case of failure, the network card 4 ports can stay.

  Distributed switching Setup

  Allows you to see how you can switch to distributed switching

  Let's start first of all, you can have EVERYTHING in switches distributed even the service console port if you wish. The resason why some people do not like to do this with the service console port is because IF your database is broken you cannot make any changes to the distributed switch. However it will not prevent a feature to your distributed it switches simply means, you can change them. Also if just getting worse and your DB has been declining for some time and you REALLY need to make a change to the service console port you can go into the console and change back to a standard vSwitch if need be. This allows the said look at some standard configs, you can work

  vSwitch0 (Standard)

  VMNIC0 - Service Console Port (Port Original ID or standby)

  VMNIC4 - Service Console Port (Port Original ID or standby)

  vSwitch1 (Standard)

  VMNIC1 - Vmotion

  VMNIC5 - Vmotion

  Distributed switch

  VMNIC2 - VMNET

  VMNIC3 - VMNET

  VMNIC6 - VMNET

  VMNIC7 - VMNET

  Now this config using originating port ID and breaks your etherchannel if you want to keep your configuration with the etherchannel it can look like this

  vSwitch0

  VMNIC0 - NETWORK interface integrated - Service Console

  VMNIC1-Onboard NIC - VMotion (different IP or VLAN?)

  VMNIC2-Onboard NIC - VMotion (different IP or VLAN?)

  VMNIC3 - NETWORK interface integrated - VMotion (eve of Console of Service) (different IP or VLAN?)

  Distributed switch

  VMNIC4 - VMNET

  VMNIC5 - VMNET

  VMNIC6 - VMNET

  VMNIC7 - VMNET

  Other changes to the configuration may also put the vmotion in distributed witch the VMNET but you would to VLAN, or you could create a second Distributed switch and put it as long as there are 2 network cards. It can go either way. The main advantage of a distributed switch is that it brings all of your settings with you in any host. So trade ect all your VIRTUAL networks is really easy to reproduce if a new host is brought online, all you have to do is to add the new host network cards in the distributed switch and your config is done. With that in mind lets look at the service console. This console is always configured on EACH Setup program that out you of the box if not that you really need to have these parameters transported on several hosts that is another reason why most people just don't. VMotion is up to you, I have seen and configured two ways, it all depends on how simple you want to keep it or think of switching / vlaning / port of groups.

  If you have any questions please let me know, I hope this has helped

• Increase throughput for iSCSI with multiple NICs

  I'm implementing a new host ESXi 6 using a Synology NAS as an iSCSI target. I have 4 nic of the Synology stuck in 1 connection, so it has 4 GB of throughput. So far, over my hosting provider, I have two nic I dedicated to iSCSI traffic. So far, I put vSwitch under 1 two NICs and I was playing with patterns. I put two 1 vmkernel network cards and set as active adapters. However when I watch the iSCSI network traffic I only see traffic on a network adapter. This of course caps my speed to 1 GB. I would like to be able to bind several network cards so I can get a flow more. I tried changing the selection of the path for the warehouses of data in Round Robin are therefore at least two active nic. But which always leaves me with two individual connections of 1 GB instead of 2 GB connection. Is it possible for me to get there or I'm better off just having several 1 GB NIC load balanced?

  I'm not familiar with the Synology. However, what is generally - in the case where the storage system supports - is to set up several uplinks on the side of the target of storage/as well as on the initiator/ESXi side, each with their own IP address. Once configured, you can use multiple paths to access the target. According to the capabilities of the target, Round-Robin (if supported) will send traffic through all the links, i.e. using the bandwidth of all the links.

  André

• Tolerance of failure with multiple NICs

  Apologize if this has been asked before.

  I'll put up a vSphere 5.5 environment and I have NIC 1 GB for each host to devote two NICs per host for tolerance to failures.  I was wondering the best way to set this up to their maximum output.  I have implemented as a Multi - NIC Vmotion?  As noted here: VMware KB: Multiple-NIC in vSphere vMotion 5. Essentially using two groups of ports as FT-1 and FT-2.  Or what I need to do as a Multi-NIC iSCSI with separate vswitches and each vswitch with a Port Group.

  Thanks in advance.

  You run into a problem of flow when you use 1 NIC for FT?

  Currently FT only supports using a single network adapter (1 G or 10 G)

• my iPhoto will not print multiple copies of a photo.

  I'm under o/s10.7.5 and iPhoto 8.1.2 version.  I've selected my photo and chose to print on the file menu.  I select the contact Board on the menu of the icon to the left of my picture. A small picture of my photo appears on the preview.  Layout page or column options had no effect and when I print only one tiny copy of my photo is displayed.  Of course, I'm in the middle of a project to date limit for which I need this feature!

  I have not use iPhoto 8 for a very long time, so do not know, is that it is valid.  With the current iPhoto 9.6.1 duplicate a photo as many times that the copies are required on the printed sheet.

  

  Select the copies, and use the Contact sheet available:

  

  Or use the custom layout and set the size to get the number of photos per page you want:

  

  NOTE: The key is to duplicate the image as many times as you need to get the number of images per page you want.

  This is how works the latest version of iPhoto.  I don't remember how iPhoto 8.1.2 manages multiple copies of a picture on a page.

  

• MacBook Pro 5.5 crashes when you use multiple applications

  Then my macbook pro 5,5 I upgraded to snow leopard at el captian started planting after that I updated when you use multiple applications (virtual dj 7.0.4 safari 9.1 and the version of microsoft word 2011 14.4.2).)

  I removed the old hdd and put in a ssd 250 GB and a new battery with the snow leopard a long time ago, before I upgraded to the new operating system. It seems to me that what is blocking it is intensive use the safari app and another intensive resources such as virtual dj application.

  I have reset pram/vram and uses firefox now...

  the computer and the new el capitan are beautiful, I really feel like im going to get a lot out of this operating system, and it gave new life to my computer, but the crash problem when using multiple applications is too often. Can I submit some reports if necessary kernel panic?

  Anonymous UUID:

  9C21D886-B7E1-F5A6-463E-8CBCF325C9D9

  Sam May 21 18:31:15 2016

  Panic report *.

  panic (cpu 0 0xffffff80115ce40a appellant): Kernel trap at 0xffffff801192a3b3, type 14 = page fault, registers:

  CR0: 0X000000008001003B, CR2: 0XFFFFEF802CCD9C40 CR3: 0X000000001320B000 CR4: 0 X 0000000000002660

  RAX: 0 X 0000000000000000, RBX: 0XFFFFFF802B945780 RCX: 0XFFFFEF802CCD9C08 RDX: 0 X 0000000000000000

  RER: 0XFFFFFF911BE53D00, RBP: 0XFFFFFF911BE53D20, IHR: 0 X 0000000000000002 RDI: 0XFFFFFF802B8FEAF0

  R8: 0 X 0000000000000000, R9: 0 X 0000000000000003, R10: 0 X 0000000000000000, R11: 0 X 0000000000000026

  R12: 0XFFFFFF802B945780, R13: 0 X 0000000000000000, R14: 0XFFFFFF911BE53E18 R15: 0XFFFFFF802B8FEAF0

  RFL: 0 X 0000000000010282, RIP: 0XFFFFFF801192A3B3, CS: 0000000000000008, SS 0 X: 0 X 0000000000000010

  Lack of CR2: 0xffffef802ccd9c40, error code: 0 x 0000000000000000, CPU error: 0x0, PL: 0

  MP = 0xffffff8022e00000, phys = 0x1367a000, prev (0 x 7: 0 x 11313000 - 0 x 11400000)

  VP = 0xffffff802b945780, phys = 0x1bd310780, prev (0xb: 0xffffc000 - 0 x 100000000)

  0xffffff8022dff000: oQAAAMsAAAAAAQAAqWwqIgAAAAAZMSk2QACp3wEAIjAAAAAAgAAAAFDw0ND1AAEACwSEgAoDAQNYXJr c9QABAAsMhMAKDwUD0FD5 / PUAAQALDETACg8FA + DQ9fz1AAEACwxEwAIDAQPQ0PX89QABAAcMhIAJAwE DoECKzPUAAQAPDISACgMBA1Bw1vz1AAEADwxEwAoDAQNwUPbc9QABAA8MhIAJAwEDoCCq3OUAAQALDIS ABQ8FA9DQudz1AAEABwxEwAoDAQNYXNbc9QABAAsMRMAKAwEDUFDW3PUAAQAPDETACQMBA9Dwuvz1AAE ADwSEwAoDAQPQ8Obc5QABAAsMhMAJAwED0ODW/AjJ5SKA / / / OB3SEQEAAQBjb20uYXBwbGUuZmxvdy1 kaXZlcgAAAgAAIAAAYG6GEbBzhhHQ8N8i5DsAAO + rd5BTEwACKiaIyrhQFcYNdERSLVmIoD / / / 8IAfI iAAAABwoAAACQb5YRAPnGIu ++ rd4QNdERKMlmIggC8iIoed8iQPbGIhA10REIA/IiuHffIogkcSogNdE RCA7yIgi2ZiKA / / / AAAABgUAAACA + MYicIMAAHySAADvvq3eyLZmIoD / / / 8IBfIiAgAAAwMAAAAIDPI iAAAAAgIAAABotmYigP / / / wMAAAMEAAAAQPjGInCFAABwgwAAcIgAAHBQAADvvq3eKuFAVxA10RGotWY igP / / / 8D4xiLvvq3eCADyIgAAAAgLAAAAEE +. WERg10REISfQiAAAACQwAAAABAAAJDQAAAED5xiLvvq3 eCLNmIghH9CIAAAAEDgAAAJQkcSoq4UBXGDXREaiyZiIAAAAFDwAAAIkkcSrgDuAg7o4JvgAO6u4LS0B A7uDuDACwAADgBOTkDO4OALCwAADgBITkDgze7gCwsABA4ASEDt7vDgCwsABAwOQE7/6/DkDA5ATuAg4 NsAAAC + QEhOzuDw4NsAAAC + QEJOyyDg4C9OT + 4OcOAAAAAABLBITs7uwODg2wAAALBITk7gcODQ4AAAt LBITsfu7n7u4ODktA5Ow + 4A0OALBLQOAA7tPuA7CwAADo0BEA/ycAOPADjz8CoIMdwAzzP AIQBqABwA Y8sxTDvLMUw7gDNAWAQBKAAkAswzAgDMAbQWADIATcACAPgMOBLQVAGgAagDAAvMM4AgAGBgFgBCA8QU OAtgWAIABLAAIECAA4AhgGwEgAAhAB0AAECQADgLYFgAIAAIn4AzQFgEgDDioE4AA6KQzD + AIABgYBYA YgAAnD8/I8wzyPAMOAgAWAOgBBhjzlCMP8yzzDOAIABgBIIkAgPwPDgLYBjgBAA4U6KQDDgLYFgAIAgo Q6XwDAAAA

  0xffffff8022e00000: IUMAABAU4CIAAID / / / 8EALi80BEIAID / / / 8MABp7AAAQAP / / / 8kAPBixxEoAID / / / 8sAOBVxhEwAID ///80ALCUoS1AAID///9EAKBXlCtIAID///9MAAAPlCtQAID///9UAIDJ6CJYAID///9cAGAA4CJoAID ///9sAADQgARwAAAA3YB0ABAAAAB8AAAQAACEAAAAEACIAEBXoAOQAHXTCQOYAHXZCAOgAMt9lwCoAD5 XoAOwAHXZCAO4AAIAAAHAABEAAADEAGhmcwDUAC8AAADkAC9kZXbkBC9kaXPoBGswczLsBAEAAADkCAg A6SL4CID / / / 8CAAAAAIACQAAAAIECQABAAAICQABAAAMCQAAQAAQCQAAQAAUCQMAAAAYCQACAAAcCSA AAAAgCQEAAAAkCRIOAABACdh4AwBICRIOAABQCYh + AwBYCQAAACFoCf / / / + ECVDK6CKICYD / / / + MCQE AAACYCQEAAACsCUAy4yLQCYD / / / UCQIAAADwCf / / / 8sCkgK4CJQCoD / / / 9UClgK4CJgCoD / / / 9kCmg K4CJwCoD / / / 90CgAQAAB4CgABAACECgAA

  0xffffff8022e01000: cAAAAIMAAACbAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AJBweH4AAAAAAAAACAACIBChIiEwKD2r/EgbMAAmkEAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAwMAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAHh8Jx80AJgAAAggAKDQhExR8Fj 8iUdIxJZ9pd9V/5 X/Vf9W/1 X/Vf9l/5r/Vf + V / wAAAgD / DwAAAAAAIf / / / 8A9sYiAgAAAACg0ySA / / / AADgIkABAACgg8YRoFbGEbDE6CLAMyErUMzoImAU4CIAEBAEABAQAOi/dSJkZXZmL2RldgAAAgD/DwA A6xQEAAAAACH / / / PwAAAIA + 4yIwzOgidOOkA1BzgwA42SaCAJGyAADfG4JAkoMALN8bgqBugwCwkIM AkKyNAKCNgwDgUIgAoE + IACBsiACAgogAAISIAMwAAAzu7u7uDgMOALDgwwAADOzg4w4O7jPuM + 7/u7 u / + 7/7u7 + 7 l/uVe5V7t7l3u7d7t3u3e7d7v3u/R7v7u7oLuEu7iLuIg4CDg4gAAgCAQD + P4DDASBozTk Bc4AAICAEQB8SbQ44DwgAN5DDDj3w / w04fysMOKDACCJg /. g04QIEFB5DAAg0gwgsdAMIIJpACCy8gQw0 4sIMPAUDAAQRgQQ8r4EIMNHCDDj0A

  Backtrace (CPU 0), frame: return address

  0xffffff911be53990: 0xffffff80114dab12

  0xffffff911be53a10: 0xffffff80115ce40a

  0xffffff911be53bf0: 0xffffff80115ec273

  0xffffff911be53c10: 0xffffff801192a3b3

  0xffffff911be53d20: 0xffffff80116f634b

  0xffffff911be53dd0: 0xffffff8011927993

  0xffffff911be53ec0: 0xffffff801170f81d

  0xffffff911be53ee0: 0xffffff80116f99e4

  0xffffff911be53f50: 0xffffff80117047d7

  0xffffff911be53f60: 0xffffff8011a27fa1

  0xffffff911be53fb0: 0xffffff80115eca76

  Name of the BSD corresponding to the current thread process: launchd

  Mac OS version:

  15E65

  Kernel version:

  15.4.0 Darwin kernel version: Fri Feb 26 22:08:05 PST 2016; root:XNU-3248.40.184~3/RELEASE_X86_64

  Kernel UUID: 4E7B4496-0B81-34E9-97AF-F316103B0839

  Slide kernel:

  0 x 0000000011200000

  Text of core base: 0xffffff8011400000

  Text __HIB base: 0xffffff8011300000

  Name of system model: MacBookPro5, 5 (Mac-F2268AC8)

  Availability of the system in nanoseconds: 3602233285655

  last load kext to 2442165091688: com.apple.driver.AppleXsanScheme 3 (addr 0xffffff7f93f64000 size 32768)

  Finally unloaded kext to 2529727624548: com.apple.driver.AppleXsanScheme 3 (addr 0xffffff7f93f64000 size 32768)

  kexts responsible:

  com Apple.filesystems.smbfs 3.0.0

  com.apple.driver.AudioAUUC 1.70

  com.apple.driver.AppleHWSensor 1.9.5d0

  com.apple.driver.AGPM 110.21.18

  com Apple.filesystems.autofs 3.0

  com.apple.driver.AppleOSXWatchdog 1

  com.apple.driver.AppleMikeyHIDDriver 124

  com.apple.driver.AppleHDA 274.7

  com Apple.Driver.pmtelemetry 1

  com.apple.iokit.IOUserEthernet 1.0.1

  com.apple.driver.AppleUpstreamUserClient 3.6.1

  com.apple.iokit.IOBluetoothSerialManager 4.4.4f4

  com.apple.driver.AppleSMCLMU 208

  com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.4.4f4

  com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0

  com.apple.driver.AppleMikeyDriver 274.7

  com.apple.driver.AppleLPC 3.1

  com.apple.GeForceTesla 10.0.0

  com.apple.Dont_Steal_Mac_OS_X 7.0.0

  com.apple.driver.AppleHV 1

  com.apple.driver.AppleIntelSlowAdaptiveClocking 4.0.0

  com.apple.driver.AppleBacklight 170.8.9

  com.apple.driver.AppleMCCSControl 1.2.13

  com.apple.driver.SMCMotionSensor 3.0.4d1

  com.apple.driver.AppleUSBTCButtons 245,4

  com.apple.driver.AppleUSBTCKeyboard 245,4

  com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1

  com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0

  com.apple.BootCache 38

  com.apple.driver.AppleIRController 327,5

  com.apple.driver.AppleUSBCardReader 3.7.1

  com.apple.iokit.SCSITaskUserClient 3.7.7

  2.8.5 com.apple.iokit.IOAHCIBlockStorage

  com.apple.driver.AirPort.Brcm4331 800.20.24

  com.apple.driver.AppleFWOHCI 5.5.2

  com.apple.driver.AppleAHCIPort 3.1.8

  com Apple.nvenet 2.0.22

  com.apple.driver.usb.AppleUSBEHCIPCI 1.0.1

  com.apple.driver.usb.AppleUSBOHCIPCI 1.0.1

  com.apple.driver.AppleRTC 2.0

  com.apple.driver.AppleHPET 1.8

  com.apple.driver.AppleSmartBatteryManager 161.0.0

  com.apple.driver.AppleACPIButtons 4.0

  com.apple.driver.AppleSMBIOS 2.1

  com.apple.driver.AppleACPIEC 4.0

  com.apple.driver.AppleAPIC 1.7

  com.apple.driver.AppleIntelCPUPowerManagementClient 218.0.0

  com Apple.NKE.applicationfirewall 163

  com Apple.Security.Quarantine 3

  com.apple.security.TMSafetyNet 8

  com.apple.driver.AppleIntelCPUPowerManagement 218.0.0

  com.apple.AppleGraphicsDeviceControl 3.12.6

  com Apple.kext.Triggers 1.0

  com.apple.driver.DspFuncLib 274.7

  com.apple.kext.OSvKernDSPLib 525

  com.apple.iokit.IOSurface 108.2.1

  com.apple.iokit.IOSerialFamily 11

  com.apple.driver.AppleHDAController 274.7

  com.apple.iokit.IOHDAFamily 274.7

  com.apple.iokit.IOAudioFamily 204.3

  com.apple.vecLib.kext 1.2.0

  com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.4.4f4

  com.apple.driver.IOPlatformPluginLegacy 1.0.0

  com.apple.driver.AppleSMBusPCI 1.0.14d1

  com.apple.driver.IOPlatformPluginFamily 6.0.0d7

  com.apple.iokit.IOFireWireIP 2.2.6

  com.apple.nvidia.classic.NVDANV50HalTesla 10.0.0

  com.apple.nvidia.classic.NVDAResmanTesla 10.0.0

  com.apple.iokit.IOBluetoothFamily 4.4.4f4

  com.apple.driver.CoreCaptureResponder 1

  com.apple.iokit.IOSlowAdaptiveClockingFamily 1.0.0

  com.apple.driver.AppleBacklightExpert 1.1.0

  com.apple.driver.AppleSMBusController 1.0.14d1

  com.apple.iokit.IONDRVSupport 2.4.1

  com.apple.iokit.IOGraphicsFamily 2.4.1

  com.apple.driver.AppleSMC 3.1.9

  com.apple.driver.AppleUSBMultitouch 250,5

  com.apple.driver.usb.AppleUSBHub 1.0.1

  com.apple.iokit.IOUSBHIDDriver 900.4.1

  com.apple.iokit.IOSCSIBlockCommandsDevice 3.7.7

  com.apple.iokit.IOUSBMassStorageDriver 1.0.0

  com Apple.Driver.USB.cdc 5.0.0

  com.Apple.Driver.USB.Networking 5.0.0

  com.apple.driver.usb.AppleUSBHostCompositeDevice 1.0.1

  com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.7.7

  com.apple.iokit.IOBDStorageFamily 1.8

  com.apple.iokit.IODVDStorageFamily 1.8

  com.apple.iokit.IOCDStorageFamily 1.8

  com.apple.iokit.IOAHCISerialATAPI 2.6.2

  com.apple.iokit.IOSCSIArchitectureModelFamily 3.7.7

  com.apple.iokit.IO80211Family 1110.26

  com Apple.Driver.corecapture 1.0.4

  com.apple.iokit.IOFireWireFamily 4.6.0

  com.apple.iokit.IOUSBFamily 900.4.1

  com.apple.iokit.IOAHCIFamily 2.8.1

  com.apple.iokit.IONetworkingFamily 3.2

  com.apple.driver.usb.AppleUSBOHCI 1.0.1

  com.apple.driver.usb.AppleUSBEHCI 1.0.1

  com.apple.iokit.IOUSBHostFamily 1.0.1

  com.apple.driver.AppleUSBHostMergeProperties 1.0.1

  2.2.9 com.apple.driver.NVSMU

  com.apple.driver.AppleEFINVRAM 2.0

  com.apple.driver.AppleEFIRuntime 2.0

  com.apple.iokit.IOHIDFamily 2.0.0

  com.apple.iokit.IOSMBusFamily 1.1

  com Apple.Security.sandbox 300.0

  com.apple.kext.AppleMatch 1.0.0d1

  com.apple.driver.AppleKeyStore 2

  com.apple.driver.AppleMobileFileIntegrity 1.0.5

  com.apple.driver.AppleCredentialManager 1.0

  com.apple.driver.DiskImages 417.2

  com.apple.iokit.IOStorageFamily 2.1

  com.apple.iokit.IOReportFamily 31

  com.apple.driver.AppleFDEKeyStore 28.30

  com.apple.driver.AppleACPIPlatform 4.0

  com.apple.iokit.IOPCIFamily 2.9

  com.apple.iokit.IOACPIFamily 1.4

  com.apple.kec.Libm 1

  com Apple.KEC.pthread 1

  com Apple.KEC.corecrypto 1.0

  System profile:

  Airport: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8D), Broadcom BCM43xx 1.0 (5.106.98.100.24)

  Bluetooth: Version 4.4.4f4 17685, 3 services, 18 aircraft, 1 incoming serial ports

  Crush Bus:

  Memory module: DIMM0/0 BANK, 4 GB DDR3, 1 333 MHz, 0x02B5, -.

  Memory module: DIMM0/1 BANK, 4 GB DDR3, 1 333 MHz, 0x02B5,--

  USB device: USB Bus

  USB device: Hub BRCM2046

  USB Device: USB Bluetooth host controller

  USB device: USB Bus

  USB device: Apple keyboard / Trackpad

  USB Device: IR receiver

  USB device: USB 2.0 Bus

  USB device: ISight built-in

  USB device: USB 2.0 Bus

  USB Device: Card reader

  Serial ATA Device: Samsung 850 EVO 250 GB, GB 250,06 SSD

  Serial ATA Device: OPTIARC DVD RW AD - 5960S

  Model: MacBookPro5, 5, MBP55.00AC.B03 of BootROM, 2 processors, Intel Core 2 Duo, 2.26 GHz, 8 GB, MSC 1.47f2

  Network service: Wi - Fi, AirPort, en1

  Graphics card: NVIDIA GeForce 9400 M, NVIDIA GeForce 9400 M, PCI, 256 MB

  The spare memory that is installed does not respect the specifications of your model (1067 MHz SDRAM.) Please reinstall the original memory, or install the new memory of the correct type.

  Any vendor deemed RAM will be a web form where you can select the Mac model and be directed to the compatible parts.

• Why can I not use shift to select several thumbnails of Pages?

  Why can I not use the SHIFT key to select several thumbnails of Pages?  I need to transfer several pages in the Pages of a document to another document, and I can't select these multiple pages in the thumbnails by pressing the shift or command key.  Help, please!

  By selecting several thumbnails, and copy and paste any thumbnails in another document of v5.6.1 Pages is not supported. You get to select the contents of a real individual page and then copy and paste between documents.

  In Pages ' 09 v4.3, you can select several thumbnails and then copy / paste these in the Gallery of thumbnails of another document. If the Pages ' 09 has been installed prior to any publication pages v5, older Pages move silently in Applications: iWork ' 09 file. You would have to export your content Pages v5.6.1 as document Pages ' 09 for backward compatibility.

• Contact ID forget the fingers after 12 hours of not used

  So I had my parents a nice Air 2 iPad with cellular data, a very good product.  The three of us each added that a finger and touch ID worked incredibly for several hours.  However the next day it would not remember neither my mom or dad.  He remembered my thumb, but then that stopped working a few hours later.

  We each added a finger several times.  However, the model is the same.  The Touch ID forget our fingers after about 12-24 hours of not used.

  My brother seems to have no problem with his iPhone 6s.  Its feature is also running iOS 9.1.

  I conjectured that perhaps the problem was that Touch ID did not like several people using the feature to unlock the device even.

  Anyway... now that I have, exclusively, have been using my new iPad (cell) Pro my theory is different.

  The drawing is the same... Contact ID works fine immediately after the addition of a finger, but overnight stops working.

  My current theory is that it works better with the phone and iPad because iPhone users tend to use their devices more continuous than iPad users.

  (at least my parents and myself) iPad users often leave the unused and locked iPad for 12 to 48 hours...

  I think that Touch ID requires frequent use to recycle permanently for the fingers "added".

  Maybe, maybe iOS 9.1 is bug in what concerns the contact ID.  Perhaps a future update may solve the problem.

  Or maybe, simply the cell iPad version has this issue.

  All things considered, I'm not discouraged by these products that they are worth every penny.

  FaceTime with iPad Air and Pro is an amazing experience.

  I submitted comments to Apple: https://www.apple.com/feedback/ipad.html

  I encourage anyone with direct problems nicely their concern to the page your comments...

  One of you, iPad users have good advice?

  Hi Camino fan 2010,

  If you encounter a problem with the contact ID not working not not always on your iPad, follow the steps in this article to troubleshoot issues - ID use Touch on iPhone and iPad.

  Specifically the section for help with the contact ID.

  Thank you for using communities of Apple Support.

  Sincerely.

• web pages of Windows vista won't load using multiple browsers.

  Windows Vista, 32-bit.
  Card mother with an AMD processor - built Gigabyte in 2009.

  Computer has worked for a few years, however, now, he can not complete the loading of most web pages.

  Using multiple browsers (IE, Firefox and Chrome), we see the same behavior - web pages do not just end.
  Sometimes update gets more of a page - but for videos (youtube and other sites) - it is almost impossible to load a full clip of more than 2 minutes.

  Ping/tracert works very well.
  If passing through the VPN + desktop remotely, things work very well (this confirms that he is not the access provider when you use remote desktop, we are no longer local + all device drivers which could be the problem).
  Windows Update, seems to work very well.

  Download files from a web page, does not work.

  The computer is currently connected via Ethernet (not wireless).
  We have tried this on two different networks, so it is not associated with ISP.

  We tried to connect a USB network adapter - thinking it was hardware related, but that has not changed anything.

  We have tried to start in safe mode with networking - and it still does not work (so probably not the program antivirus - mcafee).

  I was able to get a live LInux OS running on the pc, and he had no problem loading the pages/videos, ect - what is not strictly material.

  I tried using some of the Netsh command to reset tcp/ip stack - but they don't solve the problem.

  I do not think that it will fix a Vista startup repair, but I advise him to try to do.

  I'm looking for any other suggestions in addition to switch to Linux full time.

  Thank you!

  Hello

  Method 1:

  I suggest to perform a restore of the system and check if it helps.

  What is a system restore.

  Follow the link below and check if that helps.

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore

  Method 2: Reset TCP/IP.

  Follow the link below and reset the winsock TCP/IP settings and check if that helps.

  How to reset the Protocol Internet (TCP/IP)

  http://support.Microsoft.com/kb/299357

  http://support.Microsoft.com/kb/811259

  Let us know if it helps.

• Win 7 crashes when you use multiple wifi connections.

  Hi Shinmilla,

  I have a problem with Win 7. How did it crash the system when you use multiple wifi connections. How can I stop this from happening?

  Thank you.

  Hi Triode888,
   
  It is not recommended to have multiple Wifi connections since signals can be contradictory and therefore it crashes.
  You can't have several active Wifi connections at the same time.
   
  Also, I suspect it might be caused by your network wireless itself. It could be automatically connected to a network of 'death '. So please check that your wireless network is disabled or no if you do not use.
   
  You have installed VMware or Virtual PC?
   
  If so, these programs will create a new network - please open the network and sharing Center and disable these additional networks.
  
  1. open the network and sharing Center page in the control panel.
   
  2 confirm that it says multi-network right under the icon in the Middle, like the screenshot above.
   
  3. click on the link customize to the right of the first illustrated network, directly under the Internet icon, to display the window set the network location:
   
  4. move the window set the network location away, but let him open. (You'll need it in a minute, but at a time where it is otherwise inaccessible.)
   
  5. back on the network and sharing Center page, click on the link manage network connections (in the left task pane).
   
  6. in the network connections window, select the network adapter through which you get your Internet connection. (The views drop-down list, select Details; you want probably said something like network, unidentified in the status column.)
   
  7. click on disable this device network above (next to the big red X) button. Wait a few seconds for the chart on the network and sharing Center page to reflect the change.
   
  8. return to step #3 set network location window, and click on the merge or remove link network down locations.
   
  9. Despite Vista earlier assertion that he detected "multi-network," you will see probably only a single network in the window of merge or delete network locations:
   
  10. turn highlighted the only participant and then click on remove. (If there is more than one, you can delete all.)
   
  11. When you are finished, close the merge or delete network locations, and then close the window set the network location.
   
  12 return to the network connections window and with the adapter disabled network always highlighted the #6 step, click the option activate this device network (next to the big orange arrow) button.
   
  13. after 10-15 seconds of delay, your Internet connection should work now, signified by the absense of the treacherous of entries multiple networks in the network and sharing Center page:
   
  For more reference in http://social.answers.microsoft.com/Forums/en-US/w7network/thread/272b55ce-fb9a-423b-9a9a-8299f853cc29 look
   
  Aziz Nadeem - Microsoft Support