VPN does not bind
Something strange. It's on a 6.3 (1) PIX
Config:
flamer 90 ipsec-isakmp crypto map
card crypto flamer 90 match address h3
card crypto flamer 90 set counterpart x.x.x.x
card crypto flamer 90 transform-set esp-3des-sha
3600 seconds, duration of life card crypto flamer 90 set - the security association
part of pre authentication ISAKMP policy 90
ISAKMP policy 90 sha hash
ISAKMP policy 90 3des encryption
90 2 ISAKMP policy group
ISAKMP strategy life 90 86400
ISAKMP key
line of h3 access-list 1 ip a.a.a.a 255.255.255.192 permit host b.b.b.b (hitcnt = 28) Now nothing of a.a.a.a/29 access b.b.b.b debug crypto ipsec shows IPSec (sa_initiate): ACL = deny; No its created And the * really * part strange, my 90 isakmp policy is absent from the running configuration... not there... as if it was never set up. Uhm, help? :( Chris, Use the following to troubleshoot: In addition, you can issue: clear crypto ipsec his and: isakmp crypto claire his On your debug, it shows that there is an ACL that is denying the creation of SA! If you're still stuck please post your config pix (unscrew any sensitive info) and I'll take a look, or if you like you can post for me at: [email protected] / * / Jay Tags: Cisco Security After the upgrade yesterday from Vista to Windows 7, now my Cisco VPN does not work and I get an error message titled: grounds 440 driver fault. Any ideas to fix this? This was the solution! The works of vpn as $ 1 million now. I followed the instructions above to enter the uninstall program and selecting the repair option. I rebooted the machine, then used the troubleshooting on vpn software compatibility option. Selected Windows windows xp (service pack 2) as the correct software and cisco vpn client started right up. Thanks, Nick! Rick PPTP VPN does not work on Iphone Personal Hotspot Hello I've just updated to iOS 10 yesterday and now all my devices I use to connect to the personal hotspot on my iphone are not able to establish PPTP VPN connections. I was aware of the PPTP client are disabled in the iOS, but has actually blocked PPTP are not used by devices that connect to the Personal Hotspot? Please help ASAP, I know there are many more end-users like me having the same problem. Hello Apple does not recommend using the PPTP protocol for secure and private communication. iOS 10 and macOS Sierra intentionally delete a VPN profile PPTP connections when a user upgrades from their device. Apple recommends using another VPN protocol which is safer: More information: Prepare for removal of PPTP VPN before you upgrade to iOS 10 and macOS Sierra - Apple Support Why my internet connection dies? I use a VPN to my internet at home. I put the DNS numbers supplied by the company VPN in my airPort extreme, which, in turn, provides wireless for home. It worked perfectly until I updated to firmware 7.7.7. Suddenly the green light next to the 'internet' in airport Utility icon went Brown, and it is therefore most all internet. I put numbers in DNS to my ISP, and internet provider is displayed again. All the other numbers in DNS, whether it's Google, OpenDNS or VPN to stop the dead from the internet. Anyone has an idea about this? Airport base stations, are at best, a VPN-well past that device. It is a server or a VPN client. Upgrade to the latest firmware does not change this fact. To create a VPN tunnel using the AirPort Express Terminal, your computer must be running a VPN client that connects to a VPN server somewhere on the Internet. What DNS servers you use should make no difference with VPN. If the ISP-supplied DNS servers do not work, I would say that you contact your ISP to find out why they don't allow you to use them. What we need to study is more why you lose Internet connectivity when changing the DNS servers of your ISP. Please check with them and to report back, then we can try to help. Check sensor SFR with FireSight via VPN - does not work Hello security experts. I have an ASA5515-X with SFR installed 5.4.0 and manage with 5.4 FireSight installed on the virtual machine on LAN and I record the sensor without any problem but when I try to register the sensor to FireSight via VPN I can't do. The interface on the ASA management has no intellectual property nor nameif configured and the interface is connected to the switch, SFR has the IP even configured as LAN addressing. I can see traffic being exchanged between the sensor and the FireSight but I can't save the sensor. Has anyone managed to register the sensor via VPN? Is there something else to be configured in order to save the sensor with the MC via the VPN? The delay between the Firesight and the sensor (on WAN and VPN) I get between 80 and 100 ms, what could be the problem? Thank you very much! Remi Hello If you are unable to telnet from DC to the sensor on the port 8305 delivers connectivity then. Can try you to ping from sensor to DC: remote VPN does not work on Cisco 7206 Hello I do a test to set up remote access to VPN from Cisco 7206 (simulated by dynamips). The relevant configuration is the following: hub host name AAA new-model AAA authentication login local xauth username ciscouser password 0 cisco1234 IP subnet zero crypto ISAKMP policy 10 md5 hash Group 2 preshared authentication test group crypto isakmp client configuration key cisco123 pool mypool card crypto REMOTEACCESS client authentication list xauth Crypto ipsec transform-set RTP-TRANSFORMATION des-esp esp-md5-hmac Vpn crypto dynamic-map 1 game of transformation-RTP-TRANSFORM open crypto map REMOTEACCESS client configuration address card crypto client configuration address respond REMOTEACCESS card crypto REMOTEACCESS 1-isakmp dynamic vpn ipsec interface Ethernet0/0 IP address 150.1.1.1 255.255.255.0 card crypto REMOTEACCESS interface Ethernet0/1 IP 11.10.1.1 255.255.255.0 no ip directed broadcast to the IP local pool mypool 10.1.10.0 10.1.10.254 IP nat translation timeout never IP nat translation tcp-timeout never IP nat translation udp timeout never IP nat translation finrst-timeout never IP nat translation syn-timeout never IP nat translation dns-timeout never IP nat translation icmp timeout never IP classless IP route 0.0.0.0 0.0.0.0 10.103.1.1 no ip address of the http server end However, when I try to connect the router using the Cisco 4.6 client, you receive the following error message: 05:04:52: ISAKMP (0:1): audit ISAKMP transform 13 against the policy of priority 10 05:04:52: ISAKMP: DES-CBC encryption 05:04:52: ISAKMP: MD5 hash 05:04:52: ISAKMP: group by default 2 05:04:52: ISAKMP: auth XAUTHInitPreShared 05:04:52: ISAKMP: type of life in seconds 05:04:52: ISAKMP: life (IPV) 0x0 0 x 20 0xC4 0x9B 05:04:52: ISAKMP (0:1): pre-shared key offered Xauth authentication but does not match policy. 05:04:52: ISAKMP (0:1): atts are not acceptable. Next payload is 3 05:04:52: ISAKMP (0:1): audit ISAKMP transform 14 against the policy of priority 10 05:04:52: ISAKMP: DES-CBC encryption 05:04:52: ISAKMP: MD5 hash 05:04:52: ISAKMP: group by default 2 05:04:52: ISAKMP: pre-shared key auth 05:04:52: ISAKMP: type of life in seconds 05:04:52: ISAKMP: life (IPV) 0x0 0 x 20 0xC4 0x9B 05:04:52: ISAKMP (0:1): pre-shared authentication offered but does not match policy. 05:04:52: ISAKMP (0:1): atts are not acceptable. Next payload is 0 Does anyone have an idea? Thanks in advance. Wang, Thanks for the update! Happy in his work. The commands below are for the search for group policy. AAA authorization groupauthor LAN card crypto isakmp authorization list groupauthor REMOTEACCESS Since then, you have configured Group Policy (name, presharedkey, etc.) locally on the router, you must specify the router where to look for the isakmp policy when VPN cace tries to connect. I hope it helps. Kind regards Arul * Please note all useful messages *. PIX and ASA static, dynamic and RA VPN does not Hello I am facing a very interesting problem between a PIX 515 and an ASA 5510. The PIX is in HQ and has several dynamic VPN connections (around 130) and IPsec vpn remote works very well. I had to add a PIX to ASA L2L VPN static and it does not work as it is supposed to be. The ASA 5510, at the remote end, connects and rest for a small period of time, however, all other VPN connections stop working. The most interesting thing is that ASA is associated with the dynamic map and not the static map that I created (check by sh crypto ipsec his counterpart x.x.x.x). However, if I make any changes in the ACL 'ACL-Remote' it affects the tunnel between the PIX and ASA. Someone saw something like that? Here is more detailed information: HQ - IOS 8.0 (3) - PIX 515 ASA 5510 - IOS 7.2 (3) - remote provider Several Huawei and Cisco routers dynamically connected via ADSL Several users remote access IPsec A VPN site-to site static between PIX and ASA - does not. Here is the config on the PIX: Crypto ipsec transform-set ESP-3DES-ESP-SHA-HMAC-IPSec esp-3des esp-sha-hmac Dyn - VPN game 100 Dynamics-card crypto transform-set ESP-3DES-ESP-SHA-HMAC-IPSec Crypto dynamic-map Dyn - VPN 100 the value reverse-road VPN - card 30 crypto card matches the ACL address / remote card crypto VPN-card 30 peers set 20 x. XX. XX. XX card crypto VPN-card 30 the transform-set ESP-3DES-ESP-SHA-HMAC-IPSec value VPN crypto card - 100 - isakmp dynamic Dyn - VPN ipsec interface card crypto VPN-card outside crypto ISAKMP allow outside crypto ISAKMP policy 10 preshared authentication 3des encryption md5 hash Group 2 life 86400 crypto ISAKMP policy 65535 preshared authentication 3des encryption sha hash Group 2 life 86400 access list ACL-remote ext ip 10.0.0.0 allow 255.255.255.0 192.168.1.0 255.255.255.0 Thank you. Marcelo Pinheiro The problem is that the ASA has a crypto acl defined between host and network, while the remote end has to the network. Make sure that the acl is reversed. Cisco Anyconnect VPN does not work in windows 7 64 bit Hello I tried to solve the problems of: -Disabling the firewall. -disable the anti-virus etc. But while I tried using with 32 bit, it works very well. Also, I found that there is not a specific version of anyconnect vpn for only 64-bit. Do any body have the idea how to solve this problem, either it's a bug of cisco vpn itself? Certainly, you just need to install a later version of AnyConnect. You need a Cisco, for example a SmartNet maintenance contract, to download the new versions. Hi all I am reproducing my client on the GNS scénarion. It is a frank l2l ios vpn and I use on two NAT routers. When I train trigger (ping using the source interface) VPN, VPN is not coming, and there is no error during the isakmp debug Please go through the configuration below and suggest me Thanks toufik It does not appear to be configured for each LAN routing. May need to configure the default route on each router to point to the other. In addition, enabling the option 'enable isakmp crypto '. All the other configuration looks OK. VPN does not connect in some places I have a laptop running v5 Cisco VPN Client that connects to the office of some places network fine, but not other places. and in the places where it does not connect, it connects fine to another unrelated network. by "does not connect", I mean that I can't access any of the resources on the office network - the client software seems to work, but there is no access, I cannot ping anything on the office network. What would cause this? Here is the log file from a location where it does not connect to the office network: Cisco Systems VPN Client 5.0.07.0290 Version 1 21:36:30.625 07/03/11 Sev = WARNING/2 CVPND/0xE3400013 2 21:36:30.625 07/03/11 Sev = WARNING/2 CM/0xA3100024 in this particular case, the local network uses the range of 192.168.1.x IP addresses, so that shouldn't be a problem. Lee Could you go through a PAT instrument, so you are not able to access resources after the VPN is connected because ESP packets usually will not go through a PAT tool. What must be configured on the VPN server is to allow NAT - t (NAT Traversal), IE: encapsulation of the ESP package in UDP or TCP packet, then it passes through PAT instrument very well. What server VPN should you terminate the VPN Client? The command to activate on the SAA would be: crypto isakmp nat-traversal 20 Let me know if you have other devices like the VPN server. Hope that helps. How can I edit a movie Menu template? I use a Motion - celebrations and events - model of menu for Christmas related to 6 scene markers. Five scenes are represented by a thumbnail and name on 1 Menu scenes that appears when the button on the main menu page scene selection is reached. However, the scene 6, which has also a sticker and marker corresponding scene, is on another page (Menu 2 scenes) that does not link to the home page (does not appear in the scene selection Menu that has just 5 thumbnails and an arrow to return to the main Menu). In the area of work under the clip monitor Main Menu 1, Menu 1 and Menu 2 of scene scene appear together and by clicking on the thumbnail in the scene 2 menu the link to the clip 6 works except when Preview Disc is played, in which case the Menu 2 scene disappears. The scene marker is correctly linked, it just does not appear in the menus of the finish. The first five items of the Assembly (related to the scene selection menu) are all the video clips, but the 6th clip is a slide show. I read several threads on menus but found no mention that a slide show scene marker is treated differently by a menu template. Is it? The 5 first clips are all in the format AVI - DV with imported project files previously saved in this format, so that they could be related and engraved on a DVD. The slideshow is imported from PSE14 and 6 attached clips have already been burned successfully on disk (without menu) as a try-out. However, I was not satisfied with the resolution, then saved individually at the only other resolution DVD - SD576. Now I'm stuck at getting this sort menu. I operate 10 WIN. Any help will be accepted with gratitude. Hi, thanks for your response. I can rephrase the question very easily: why I've been so stupid? My problem was that I couldn't see a link in the menu between the Menu scenes 2 template and the main Menu. It turns out that the link was there all the time (a sideway arrow just above the main Menu link) but I thought he was part of the link from the main Menu and never clicked on it. When I burned my project to a disc and played on television, the sideway arrow was a different color and, of course, another link... the link I was looking for. Then, my apologies, problem solved, lesson learned - click on everything you see. Thank you. And I was very happy since the upgrade to 14 before except when it makes me feel stupid, which is frequently. Hi- I notice that if I add a clip to the sequence in first pro CS6 it does not appear in the linked timeline dynamically in yet. Make any other changes such as transitions, destruction, corrections etc. Is this a known limit or is there a way to get around this? Thank you very much. Ken zeina If you add it at the end of the sequence, you may need to extend the timeline again. If transcode you assets (the sequence of PR), you "go back to the original" to see the changes. PP 2014 and SOUL does not bind When I send my export to the queue, SOUL opens but the export does not appear. I had to export from PP to get anything, which was a huge waste of time for me the last few days. How should I do? So, if this isn't a sequence and you simply import a single video file into SOUL, this work? In addition, please try to hold the SHIFT key and throw the SOUL. This resets the preferences. It can help. Cisco VPN does not work in the Sierra I just upgraded to OS Sierra and the Cisco VPN, I had the installer does connect more. The Setup looks right into network preferences. When I click it looks like it is trying but stops without asking for a password. Cisco VPN client may need to update or re-installed. If she uses the PPTP Protocol, it will not work. Support for PPTP was ignored, because it is no longer considered as secure. VPN does not boot... ASA 5505 Hi all I encountered a problem and hopefully one (or more!) of you have seen this before. I configured an ASA5505 to be endpoint tunnel VPN Lan to Lan, peering with a Linux links. The SAA is full licensed so that side is not a problem. PROBLEM: When the tunnel is initialized from the linux box everything is happening very well except the ASA is not encapsulation of packages. They are decrypted packets from the Linux box agreement, but not return traffic are encryption. When the tunnel is initialized to the ASA, nothing happens. After some troubleshooting I found that the ACL defines interesting traffic or the ACL setting NO_NAT will are not affected at all. ACL for NO_NAT: access-list NO_NAT line 1 Note USED ACL TO DEFINE WHAT TRAFFIC NOT NAT ON THE VPN permit for line NO_NAT of access list lengthened 2 ip host LINUX-AREAS of PAMS_SERVER object-group 0xc736d5fb allowed to Access - list NO_NAT line 2 extended host ip PAMS_SERVER 10.11.228.0 255.255.255.0 (hitcnt = 0) ACL for interesting traffic LNX_IPSEC list of access; 2 elements; hash name: 0xda433bf Line note 1 LNX_IPSEC to access list ACL USED TO DEFINE WHAT TRAFFIC to ENCRYPT permit for line LNX_IPSEC of access list lengthened 2 ip host LINUX-AREAS of PAMS_SERVER object-group 0x49989fbd allowed to Access - list LNX_IPSEC line 2 extended host ip PAMS_SERVER 10.11.228.0 255.255.255.0 (hitcnt = 0) 0x6f1aad85 permits for Access - list extended LNX_IPSEC line of 3 ip host 10.1.85.156 LINUX-AREAS of 0x034eece3 object-group allowed for extended access list of 3 ip host 10.1.85.156 LNX_IPSEC line 10.11.228.0 255.255.255.0 (hitcnt = 0) 0xc3b2fc0b I checked with the administrator of the linux machine and the definition of interesting traffic is exactly the same (except in reverse, that should be the case). The firewall is doing other things such as NATs and as too but the NATs have nothing to do with this VPN. The configuration is a LAN connection to LAN with no natting between the two. The main parts of the config are attached, I deleted that should have an impact on this, but if you think it is necessary I can clean up the config and re-post. I think it will work very well as long as the traffic hitting these ACLs, but they are not and I'm not sure why. Right now I don't see anything when doing a Cree debugging ipsec or debug cry ISA. The ACL are not being touched so I think he's trying to not even form the VPN as it can not see all traffic which is being 'interesting '. Has anyone seen this problem before or someone has any advice that I might be able to use to make it work? Thanks in advance for any help Brad How are those that hosts (PAMS_Server and 10.1.85.156) which is routed? You did not include the routing within the clinical setting and wondered if the routing is correct. So, I have forgotten my security questions answers/format and no longer have access to my e-mail address of relief. What can I do? Can I plot the data in a graphical table of references? I have a request, when the customer asked 12 plots on a single screen. These plots data in a table. It would save me a lot of time if I could make a table of controls and wire then the data that their using a structure. I tried to do this with an I read some of the problems and solutions but cannot find mine. I tried some of the suggestions, but got stuck in the registry editor. Followed the instructions but I had once to policies-Microsoft-Windows. I don't have windows update so that I co Windows Update does not work after new hard drive After you install the new hard drive, when I click on windows update, it opens, makes his scan, then I get the message, (the website has encountered a problem and cannot display the page) I have a Dell Optiplex 745 running XP Pro, Explorer 8, have tr How to: display "last configuration change. How can I get my routers to display: "The last configuration change" and "configuration change since...". » and if possible I can trap on these? 1720 = 12.2 IOS Thank you in advance, BartSimilar Questions
ping -M do -c 20 -s 1572
By default, the MTU is 1500 on eth0, if the ping does not work I will suggest to lower the MTU on the interface and see if it works.
See also: / var/log/messages | grep sftunnel and see the error messages on DC and sensor and send it to me everywhere.
Best regards, Aastha Bhardwaj rate if this is useful!
I found that the cisco anyconnect (version 3, any series) does not work in windows 7 (64-bit).
The vpn is connected, but there is not any internet access.
Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.
Customer type: Windows, Windows NT
Running: 6.1.7600
Directory of config files: E:\Cisco systems VPN Client\
AddRoute cannot add a route which the metric is 0: code 160
Destination 5.0.0.0
Subnet mask 255.0.0.0
Gateway 192.36.253.1
Interface 192.36.253.179
Failed to add the route. Network: 5000000, subnet mask: ff000000, Interface: c024fdb3 Gateway: c024fd01.Maybe you are looking for