VPN LAN - to - LAN ASA of the multiple Interfaces

Similar Questions

• VPN site-to-customer contact on the external interface

  Hello

  I would like to configure client-to-site ipsec vpn using asa as an attachment. I tested, but it seemed that it did not work. I don't know if it of possible or not. Could someone advise me please?

  Thanks in advance,

  Nitass

  Network diagram

  Here's what you can do. On the SAA add a static host for the server route, but do point to the inside interface of the firewall.

  route inside 10.0.2.100 255.255.255.255 10.0.1.254

  The firewall knows that he has to get out of the e2 interface because it is directly connected.

  On the server, you will need a static route to the VPN Pool pointing on the firewall.

  route add 10.0.3.0 mask 255.255.255.0  10.0.2.254

  On the firewall, you also have to add a route for the VPN Pool.

  route inside 10.0.3.0 255.255.255.0 10.0.1.200

• Cannot ping inside the ASA from the inside interface

  Don't know what I did wrong... appreciate any help

  Here is the page layout

  laptop--> cisco 3750 switch--> ASA5505 firewall--> future VPN tunnel

  Laptop, switch interface VLAN and inside the ASA are all in the same subnet

  Switch and ASA have all interfaces local network VIRTUAL 52 (the subnet in question), except for the external interface

  -----------------

  This is the problem

  laptop getting ip addressing and def GW via DHCP from the firewall

  switch and FW can ping each other without problem

  FW can't ping, still gets the DHCP scope.

  Thank you

  Dave

  Hello

  How did you setup?

  The laptop is connected to a port of the 3750 (VLAN 52).

  The connection between the 3750 and the SAA is a chest or a link L3?

  If the 3750 has a SVI belonging to VLAN52, you can ping from the correct PC? As well as the ASA?

  Federico.

• Access ASDM ASA on the external Interface

  We have three ASA5510s, each configured for ssh and http access to the Cel outside.  One of them has aaa users/passwords defined for both ssh and http.  I can access the ASA configured for aaa of the designated host allowed in the external interface normally using credentials of the aaa.  When I try to access one of the other two, they will refuse the enable login password.  The configured aaa ASA is version 8.2 with ASDM 6.21.  The other two are the two ASA version 7.0 with ASDM 5.07.  The ASA requires aaa is configured for https access?  How can I make these other two accept the ASDM login?  Thank you!

  If you do not have aaa then configured for ASSISTANT Deputy Ministers, you must use empty username and password enable.

  Also, you can use the "aaa authenticate http LOCAL console" and use a user/pwd to a private 15 user name to connect to the ASDM.

  To resolve what is a failure you can activate "debug http" and "debug aaa" on the SAA to see the reasons for which the user is rejected.

  I hope it helps.

  PK

• How to configure the VPN LAN to access the internet from the remote network

  I have set up for our project site to another Office VPN. Please join.
  Now I have already configured Site to site vpn between ASA 5510 and 1841 router.

  HQ LAN

  Branch of the LAN
                   10.2.1.0/24 > ASA 5510 1841 > > INTERNET < 1841=""> <> 10.30.3.0/24
  ^
  ^
  ^
  ^
  Call Manager
  No. 2851
  Now access from branch LAN LAN of HQ each other.

  I face problems that are
  (1) in the direction of LAN, they can access HQ LAN & resource, but cannot access the internet. I did not configure NAT on the router PH
  (2) can I access internet BRANCH LAN via HQ LAN INTERNET. Where can I access the Internet of general management of the LAN of the PH router directly while access to the VPN to the local network of HQ?
  (3) in the Site of the Directorate, phone hard cannot work but phone on PC can call to Headquarters. Hard IP phone are same in remote network (172.16.1.0/24 ). What's the problem? How can I configure separately?

  Please give advise me how should I do.

  Hello

  (1) in the direction of LAN, they can access HQ LAN & resource, but cannot access the internet. I did not configure NAT on the router PH

  Answer:

  You must configure the NAT and crossed to the ASA HQ so that the VPN branch router provides LAN and u-Turn, access to Internet of the SAA.  You must first seup NAT for the branch on the SAA router subnet, then you must type the command:

  permit same-security-traffic intra-interface

  Here's a great example for VPN client hairpining.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  (2) can I access internet BRANCH LAN via HQ LAN INTERNET. Where can I access the Internet of general management of the LAN of the PH router directly while access to the VPN to the local network of HQ?

  Yes, you can

  (3) in the Site of the Directorate, phone hard cannot work but phone on PC can call to Headquarters. Hard IP phone are same in remote network (172.16.1.0/24 ). What's the problem? How can I configure separately?

  You must change your subnet VLANS to be different from the subnet HQ voice phone IP VOice VLAn, it should be fine.

  Kind regards

  Mohamed

• Cisco ASA 5510, ipsec vpn. What address to connect the client to

  Hello

  It's maybe a stupid question, but I can't find the answer anywhere.

  I used the ipsec vpn configuration wizard, I activated the external interface to access ipsec and went through SCW pools of addresses etc. When I try to connect with the cisco vpn client to my address of the external interface (of a remote host) I'm unable to connect. I scanned the interface for open ports, but there is not, I have to allow traffic to ipsec at this interface?

  Best regards

  Andreas

  No, once you have configured the access remote vpn ipsec, it will be automatically activated, and you should be able to connect to the ASA outside the ip address of the interface.

  Can you please share the configuration? and also which group name you are trying to access the vpn client?

• AnyConnect VPN full tunnel could not access the site to site VPN

  I have a set of AnyConnect VPN upward with no split tunneling (U-turning/crossed traffic), running 8.2.5 code.

  It works fine, but I want to allow customers to AnyConnect VPN site to site, which I was unable to access.

  I checked the IP addresses of network anyconnect are part of the tunnel on both sides.

  My logic tells me that I must not turn back traffic from the network anyconnect for the site to site VPN, but I don't know how to do this.

  Any help would be appreciated.

  Here are the relevant parts of my config:

  (Domestic network is 192.168.0.0/24,

  the AnyConnect network is 192.168.10.0/24,

  site to site VPN network is 192.168.2.0/24)

  --------------------------------------------------------------------------------------

  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface

  the DM_INLINE_NETWORK_1 object-group network
  object-network 192.168.0.0 255.255.255.0
  object-network 192.168.10.0 255.255.255.0
  inside_nat0_outbound list extended access allowed object-group ip DM_INLINE_NETWORK_1 192.168.2.0 255.255.255.0
  permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.10.0 255.255.255.0

  outside_1_cryptomap list extended access allowed object-group ip DM_INLINE_NETWORK_1 192.168.2.0 255.255.255.0

  mask 192.168.10.2 - 192.168.10.254 255.255.255.0 IP local pool AnyConnectPool
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0
  NAT (outside) 1 192.168.10.0 255.255.255.0
  access-outside group access component software snap-in interface outside
  Route outside 0.0.0.0 0.0.0.0 (the gateway IP) 1
  WebVPN
  allow outside
  AnyConnect essentials
  SVC disk0:/anyconnect-win-3.1.05152-k9.pkg 1 image
  SVC profiles AnyConnectProfile disk0: / anyconnect_client.xml
  enable SVC
  tunnel-group-list activate
  internal AnyConnectGrpPolicy group strategy
  attributes of Group Policy AnyConnectGrpPolicy
  WINS server no
  value of 192.168.0.33 DNS server 192.168.2.33
  VPN-session-timeout no
  Protocol-tunnel-VPN l2tp ipsec svc
  Split-tunnel-policy tunnelall
  the address value AnyConnectPool pools
  type tunnel-group AnyConnectGroup remote access
  attributes global-tunnel-group AnyConnectGroup
  address pool AnyConnectPool
  authentication-server-group SERVER1_AD
  Group Policy - by default-AnyConnectGrpPolicy
  tunnel-group AnyConnectGroup webvpn-attributes
  the aaa authentication certificate
  activation of the Group _AnyConnect alias

  Your dial-up VPN traffic as originating apears on the external interface, so I think you need to exonerate NAT pool PN traffic directed to the site to site VPN. Something like this:

   global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 nat (outside) 0 access-list outside_nat0 nat (outside) 1 192.168.10.0 255.255.255.0 access-list outside_nat0 extended permit ip any 192.168.10.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.255.0 192.168.10.0 255.255.255.0

• Unable to access the remote VPN LAN

  My VPN ends very well, but cannot access the local network. The warning is the LAN is a public good 24 subnet.  I'm not sure how to NAT the LAN to access the VPN subnet and not to disturb any other functionality.  I have attached the configuration.

  Thank you in advance.

  ciscoasa # sh run
  : Saved
  :
  ASA Version 8.2 (2)
  !
  ciscoasa hostname
  activate the encrypted Anuj/1RTcTy/SmZO password
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP address .149.200 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP address *.165.37.131 255.255.255.248
  !
  interface Vlan5
  No nameif
  security-level 50
  IP 10.10.10.1 255.255.255.0
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  switchport access vlan 5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  passive FTP mode
  clock timezone GMT 0
  standard permit access list MASTERPWRTRANS_splitTunnelAcl *. . 149.0 255.255.255.0
  allow inside_nat0_outbound to access extensive ip list *. . 149.0 255.255.255.0 172.30.110.0 255.255.255.224
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  local pool POOL1 172.30.110.1 - 172.30.110.30 IP 255.255.255.224 mask
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  Global (outside) 2 *.165.37.132
  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 2 *. .149.199 255.255.255.255
  NAT (inside) 1 0.0.0.0 0.0.0.0
  static (exterior, Interior) *. .149.199 *.165.37.132 netmask 255.255.255.255
  Route outside 0.0.0.0 0.0.0.0 * 1.165.37.134
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  RADIUS protocol Server AAA MPT
  AAA server MPT (inside) host .149.210
  Timeout 5
  key *.
  AAA authentication enable LOCAL console
  the ssh LOCAL console AAA authentication
  Enable http server
  http 0.0.0.0 0.0.0.0 inside
  http 0.0.0.0 0.0.0.0 outdoors
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400
  Telnet *. . 149.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 5
  Console timeout 0
  management-access inside

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  internal MASTERPWRTRANS group policy
  MASTERPWRTRANS group policy attributes
  value of DNS server *. . 149.10 *. . 149.11
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list MASTERPWRTRANS_splitTunnelAcl
  MCI.local value by default-field
  ptiadmin encrypted BtOLil2gR0VaUjfX privilege 15 password username
  mptadmin U2T.1fmOIe772zE username password / encrypted
  type tunnel-group MASTERPWRTRANS remote access
  attributes global-tunnel-group MASTERPWRTRANS
  POOL1 address pool
  TPM authentication server group
  Group Policy - by default-MASTERPWRTRANS
  IPSec-attributes tunnel-group MASTERPWRTRANS
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:820529ed70de923a8375694004b2544c
  : end
  ciscoasa #.

  The 2821 should have a route pointing to the ASA for the VPN address pool (because the ASA is not the default gateway for the LAN).

  That should do it.

  Federico.

• The application of SECURITY for VPN LAN to LAN traffic!

  I have a question on the forum,

  Can apply you security for inbound ipsec traffic once it has been deciphered? I did some research and cannot come to this conclusion, with a LAN to LAN Vpn using ipsec allowed sysopt command bypass you all ACL audit (the access list incoming or conducted applied to the external interface) and cannot so apply any security to inbound traffic to your internal network via the VPN any VPN interface ends at. It is my understanding that instead of using the permitted sysopt command ipsec, you can allow protocol 50 (esp) in your firewall allowing traffic to reach the firewall and be decrypted BUT can you then apply any security to it? He will re-evaluate himself against the inbound ACL applied to the external interface?

  -Jeremy

  Hi Jeremy,.

  Your understanding is to a specific point. Once the packet is decrypted, it will reassess not himself against the acl entering applied outward whetther regardingless configuring acl or use sysopt. Thank you

  Renault

• Ping LAN internal via the IPSec VPN Client

  It's my scenario.

  Software Version 7.2 (1)

  I activated the VPN in the external Interface. The IPSec Client pool is in the range 192.168.98.150 - 192.168.98.175.

  • Allowed "a whole icmp" out Interface access both within the Interface.
  • ICMP & ICMP error inspection is enabled.
  • NAT-control is disabled.

  Clients are unable to ping any IP within the LAN 'inside' but at the same time, they are able to access the devices in the LAN using HTTP, HTTPS, SSH & TELNET.

  CASE 1:

  access-list SHEEP extended permits all ip 192.168.98.0 255.255.255.0

  NAT (Inside) 0 access-list SHEEP

  I get the following log "translation portmap creation failed for CBC icmp outdoors"

  CASE 2:

  If I add a static 192.168.98.0 public (exterior, Interior) 192.168.98.0 netmask 255.255.255.0

  I am able to Ping and the problem is solved.

  Could someone explain please this behavior?

  1. Why ICMP only needs a NAT device when TCP & UDP traffic works very well.
  2. Why a portmap translation error? Why not dynamic identity NAT?

  Hello

  So he was correspondent to a configuration 'nat' on the 'outside' interface that had no configuration corresponding 'global' for the destination (probably inside) interface which caused problems and produces the 'portmap' error.

  Please do not forget to mark an answer as the correct answer, if she answered your question or useful rate responses

  -Jouni

• Based on the IOS VPN Lan-to-Lan (NAT and route map Questions)

  Hello world

  I worked on my review of CCNA security and I have a question about this stage

  LAN1 192.168.0.0/24---(routeur HQ)--10.10.10.0/30--(INTERNET)--20.20.20.0/30--(routeur Branch) - LAN2 192.168.1.0/24

  I use 10.10.10.0/30 and 20.20.20.0/30 networks assuming that these are public addresses (is just a laboratory).

  I read that if I want to make the VPN tunnel while I using NAT I must exclude valuable traffic from the NAT process so I look on the database of cisco for more help and I found this (look at the 3660 router configuration):

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a008045a2d2.shtml#T1

  so, I applied this config for my routers, so the config is:

  IP nat inside source map route sheep interface fastEthernet0/1

  access list 110 deny ip 192.168.0.0. 0.0.0.255 192.168.1.0 0.0.0.255

  access list 119 permit ip 192.168.0.0. 0.0.0.255 any

  sheep allowed 10 route map

  corresponds to the IP 110

  I didn't really understand who is using the command route-map here, so I made this configuration:

  IP nat inside list sheep interface FastEthernet0/1

  sheep extended IP access list

  deny ip 192.168.0.0 0.0.0.255 192.168.1.0 0.0.0.255

  Licensing ip 192.168.0.0 0.0.0.255 any

  Two of them worked I could translate my LAN addresses to the public to address internet and also could establish the VPN tunnel. So my questions are:

  1. What is the purpose of the road-map command?

  2. What is the difference between these two configuration?

  3. which one I should use and in what cases?

  Thanks in advance

  Jose

  Jose,

  Very good questions and in fact no need to the road map it.

  Personally, I like using course maps because it allows much more flexibility than simply ACL setup, but in order to bypass the NAT source IPs, there is no need of route-maps and you can do this with the ACL directly.

  I personally always use road-maps just because I can (route-maps are cool) haha

  Route-maps are very useful in other scenarios where you need to put more of conditions or factors.

  Remember that it is almost always more than one method to accomplish a task... which is one of those cases.

  It will be useful.

  Federico.

• LAN ASA 5505 VPN client access issue

  Hello

  I'm no expert in ASA and routing so I ask support the following case.

  There is a (running on Windows 7) Cisco VPN client and an ASA5505.

  The objectives are client can use the gateway remote on SAA for Skype and able to access devices in SAA within the interface.

  The Skype works well, but I can't access devices in the interface inside through a VPN connection.

  Can you please check my following config and give me any advice to fix NAT or VPN settings?

  ASA Version 7.2 (4)

  !

  ciscoasa hostname

  domain default.domain.invalid

  activate wDnglsHo3Tm87.tM encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  interface Vlan3

  prior to interface Vlan1

  nameif dmz

  security-level 50

  no ip address

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain default.domain.invalid

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  inside_access_in list extended access permitted tcp 192.168.1.0 255.255.255.0 any

  inside_access_in list extended access permitted udp 192.168.1.0 255.255.255.0 any

  outside_access_in list of allowed ip extended access entire 192.168.1.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  MTU 1500 dmz

  local pool VPNPOOL 10.0.0.200 - 10.0.0.220 255.255.255.0 IP mask

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 524.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT-control

  Global 1 interface (outside)

  NAT (inside) 1 10.0.0.0 255.255.255.0

  NAT (inside) 1 192.168.1.0 255.255.255.0

  NAT (outside) 1 10.0.0.0 255.255.255.0

  inside_access_in access to the interface inside group

  Access-group outside_access_in in interface outside

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  the ssh LOCAL console AAA authentication

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto-map dynamic outside_dyn_map pfs set 20 Group1

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH 192.168.1.0 255.255.255.0 inside

  SSH timeout 5

  SSH version 2

  Console timeout 0

  dhcpd outside auto_config

  !

  dhcpd address 192.168.1.2 - 192.168.1.33 inside

  dhcpd dns xx.xx.xx.xx interface inside

  dhcpd allow inside

  !

  attributes of Group Policy DfltGrpPolicy

  No banner

  WINS server no

  value of server DNS 84.2.44.1

  DHCP-network-scope no

  VPN-access-hour no

  VPN - connections 3

  VPN-idle-timeout 30

  VPN-session-timeout no

  VPN-filter no

  Protocol-tunnel-VPN IPSec l2tp ipsec webvpn

  disable the password-storage

  disable the IP-comp

  Re-xauth disable

  Group-lock no

  disable the PFS

  IPSec-udp disable

  IPSec-udp-port 10000

  Split-tunnel-policy tunnelall

  Split-tunnel-network-list no

  by default no

  Split-dns no

  Disable dhcp Intercept 255.255.255.255

  disable secure authentication unit

  disable authentication of the user

  user-authentication-idle-timeout 30

  disable the IP-phone-bypass

  disable the leap-bypass

  allow to NEM

  Dungeon-client-config backup servers

  MSIE proxy server no

  MSIE-proxy method non - change

  Internet Explorer proxy except list - no

  Disable Internet Explorer-proxy local-bypass

  disable the NAC

  NAC-sq-period 300

  NAC-reval-period 36000

  NAC-by default-acl no

  address pools no

  enable Smartcard-Removal-disconnect

  the firewall client no

  rule of access-client-none

  WebVPN

  url-entry functions

  HTML-content-filter none

  Home page no

  4 Keep-alive-ignore

  gzip http-comp

  no filter

  list of URLS no

  value of customization DfltCustomization

  port - forward, no

  port-forward-name value access to applications

  SSO-Server no

  value of deny message connection succeeded, but because some criteria have not been met, or because of a specific group policy, you are not allowed to use the VPN features. Contact your administrator for more information

  SVC no

  SVC Dungeon-Installer installed

  SVC keepalive no

  generate a new key SVC time no

  method to generate a new key of SVC no

  client of dpd-interval SVC no

  dpd-interval SVC bridge no

  deflate compression of SVC

  internal group XXXXXX strategy

  attributes of XXXXXX group policy

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelall

  Split-tunnel-network-list no

  XXXXXX G910DDfbV7mNprdR encrypted privilege 15 password username

  username password encrypted XXXXXX privilege 0 5p9CbIe7WdF8GZF8

  attributes of username XXXXXX

  Strategy Group-VPN-XXXXXX

  username privilege 15 encrypted password cRQbJhC92XjdFQvb XXXXX

  tunnel-group XXXXXX type ipsec-ra

  attributes global-tunnel-group XXXXXX

  address VPNPOOL pool

  Group Policy - by default-XXXXXX

  tunnel-group ipsec-attributes XXXXXX

  pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  inspect the icmp

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum:a8fbb51b0a830a4ae823826b28767f23

  : end

  ciscoasa #.

  Thanks in advance!

  fbela

  config #no nat (inside) 1 10.0.0.0 255.255.255.0< this="" is="" not="">

  Add - config #same-Security-permit intra-interface

  #access - extended list allowed sheep ip 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0

  #nat (inside) 0 access-list sheep

  Please add and test it.

  Thank you

  Ajay

• Transfer the image to the ASDM ASA on the anyconnect VPN

  I'm relatively new to the ASA firewalls.  My previous experience of firewall is a firewall provider.  I work with an ASA 5515 - X running ASA 915 and ASDM 713.  I connect Windows 8 and therefore improve the ASDM to 731.  I've done it before no problem.  My problem with this particular update is that I really need to download the image to a VPN connection.  I can't configure a NAT device on my end to allow the ASA to connect to my public IP address - so I can connect to the ASA via anyconnect.  I can't SSH in public IP address of the ASA (for now) but I can't transfer the asdm image obviously not my public IP b/c I have no NAT on my end.  So I connect my PC to the anyconnect service and get an IP VPN.  I need to run the command:

  copy ftp://user: [email protected] / * *//asdm-731.bin disk0:

  I get the following output: for access to the ftp://user: [email protected] / * *//asdm-731.bin...
  Error opening % ftp://user: [email protected] / * *//asdm-731.bin (Permission denied)

  Anyone know good ways to solve this CLI only?

  Thanks for your help.

  Zach

  Looks like a FTP permission problem. The user has read access? Also, make sure that your 8 victory is tuned for FTP requests on map virtual VPN.

  one of the other option is to use a host of jump in your lan behind asa and open the asdm from there, using asdm, it will be easier to copy the file to asa flash.

• L2l VPN between ASA with the IP address public and CISCO2911 behind the ISP router with port forwarding

  Hi all

  My apologies if this is a trivial question, but I spent considerable time trying to search and had no luck.

  I encountered a problem trying to set up a temporary L2L VPN from a Subscriber with CISCO2911 sitting behind the router of the ISP of an ASA. ISP has informed that I can't ignore their device and complete the circuit Internet on the Cisco for a reason, so I'm stuck with it. The Setup is:

  company 10.1.17.1 - y.y.y.y - router Internet - z.z.z.z - ISP - LAN - 10.x.x.2 - XXX1 - ASA - 10.1.17.2 - CISCO2911 - 10.1.15.1 LAN

  where 10.x.x.x is a corporate LAN Beach private network, y.y.y.y is a public ip address assigned to the external interface of the ASA and the z.z.z.z is the public IP address of the ISP router.

  I have forwarded ports 500, 4500 and ESP on the ISP router for 10.1.17.2. The 2911 config attached below, what I can't understand is what peer IP address to configure on the SAA, because if I use z.z.z.z it will be a cause of incompatibility of identity 2911 identifies himself as 10.1.17.2...

  ! ^ ^ ^ ISAKMP (Phase 1) ^ ^ ^!
  crypto ISAKMP policy 5
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  lifetime 28800
  isakmp encryption key * address no.-xauth y.y.y.y

  ! ^ ^ ^ IPSEC (Phase 2) ^ ^ ^!
  crymap extended IP access list
  IP 10.1.15.0 allow 0.0.0.255 10.0.0.0 0.255.255.255
  Crypto ipsec transform-set ESP-3DES-SHA 3rd-esp esp-sha-hmac
  card crypto 1 TUNNEL VPN ipsec-isakmp
  defined peer y.y.y.y
  game of transformation-ESP-3DES-SHA
  match the address crymap

  Gi0/2 interface
  card crypto VPN TUNNEL

  Hello

  debug output, it seems he's going on IPSEC States at the tunnel of final bud QM_IDLE's.

  What I noticed in your configuration of ASA box, it's that you're usig PFS but not on 2911 router.

  So I suggest:

  no card crypto OUTSIDE_map 4 don't set pfs <-- this="" will="" disable="" pfs="" on="" asa="">

  Then try tunnel initiate.

  Kind regards

  Jan

• Connected to the ASA via the "VPN Client" software, but cannot ping devices.

  I have a network that looks like this:

  

  I successfully connected inside the ASA via a software "Client VPN" tunnel network and got an IP address of 10.45.99.100/16.

  I am trying to ping the 10.45.99.100 outside 10.45.7.2, but the ping fails (request timed out).

  On the SAA, including the "logging console notifications" value, I notice the following message is displayed:

  "% 305013-5-ASA: rules asymmetrical NAT matched for flows forward and backward; "Connection for icmp src, dst outside: 10.45.99.100 inside: 10.45.7.2 (type 8, code 0) rejected due to the failure of reverse path of NAT.

  I have a vague feeling that I'm missing a NAT rule of course, but not all. What did I miss?

  Here is my configuration of ASA: http://pastebin.com/raw.php?i=ad6p1Zac

  Hello

  You seem to have a configured ACL NAT0 but is not actually in use with a command "nat"

  You would probably need

  NAT (inside) 0-list of access inside_nat0_outside

  He must manage the NAT0

  Personally, I would avoid using large subnets/networks. You probably won't ever have host behind ASA who would fill / 16 subnet mask.

  I would also keep the pool VPN as a separate network from LANs behind ASA. The LAN 10.45.0.0/16 and 10.45.99.100 - 200 are on the same network.

  -Jouni