Want to use internet to share WRV210 router between two LANs

Similar Questions

• Help! Static route between two router WRT160NL

  Hi all

  I have my internet connection to connect to my main router from Linksys WRT160NL (192.168.1.1) with 192.168.1.x.

  My 2nd Linksys router to connect to the first gateway as well.
  The 2nd router has the ip 192.168.1.100 WAN and it's a local subnet as 192.168.2.x.

  My 192.168.2.x machines can access the internet and connect to all the machines in the network 192.168.1.x.

  However, the 1.x network cannot access the machines on the network of the 2. And because of that, I can't share or print between two networks.

  I try to add static routes on my main router (192.168.1.1) with the road: 192.168.2.0 mask 255.255.255.0 and default gateway 192.168.1.100

  However, the road does not work yet.

  in any case to ensure that the 1.x network able to access the network 2.x and 2.x access 1.x file and print sharing.

  Thanks for your help!

  Gateway of the router does NAT who made the side inaccessible side LAN WAN, unless you configure port forwarding automatic or similar. If she would not make your LAN 192.168.1 would be accessible from the internet. Static routing will not change that.

  You will need to disable NAT (aka switch to router mode) on the second router. You must configure a static route on the main router then. However, most likely your network 192.168.2 * will not have Internet more because the main router will NAT for 192.168.1. * and no 192.168.2. *.

  If possible set up the second router as access point only and run a LAN.

• I use SyncToy 2.1 for syncing between two readers and I wonder if it is possible to synchronize three discs without causing confusion for SyncToy.

  Hi all, I use SyncToy 2.1 for syncing between two readers and I wonder if it is possible to synchronize three discs without causing confusion for SyncToy. In other words, I want to have a (portable) master and synchronize with a Home Office and a disc of office disc.

  Original title: SyncToy 2.1

  Hello

  Thanks for posting your question on Microsoft Community!

  After your description, it seems that you need more information about SyncToy 2.1.

  I would like the season help you post you question on the following link for better.
  http://social.Microsoft.com/forums/en-us/SyncToy/threads

  I hope this helps!

• How to make a route between two routers (networks) connected to the same switch?

  Hello guys, how are you?

  In my company, we have 2 internet routers more dsl router of data connected to 1 switch line

  the data row is used to connect the branches of our company together for network problems.

  the router 192.168.2.1 IP data

  internet routers IP 192.168.1.1 - 57.194.97.1

  We have 3 accesspoints wireless taking their internet of 192.168.1.1 oky guy

  what I want to do is when I connect to any wireless network to connect to the data line dsl with router 192.168.2.1

  When I use the ethernet on my pc I have IP addresses 192.168.2.222 for router data line and 192.168.1.222 for internet

  but the wireless is DHCP n that it is connected only to 192.168.1.1, which is the internet router, how can I do 192.168.1.1 192.168.2.1 when I connect

  using the wireless?

  I hope that you understand me ^_^

  Thanks in advance.

  Hello

  The question you posted would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/en/category/w7itpro/

  Hope this information is useful.

• Routing between two network cards

  I have 8 fiber switches that are configured to use a private network for management.

  The subnet is 192.168.8.0/24.

  I have a W2K3 (SERVER A) server with two NICS, a NIC (192.168.8.1) is attached to

  the 192.168.8.0 subnet and the other (192.168.100.14) NETWORK adapter is attached to the subnet 192.168.100.0/24.

  I put up two persistent routes of road between these NICS using the following commands:

  Pei route add 192.168.8.0 mask 255.255.255.0 192.168.100.14

  Pei route add 192.168.100.0 mask 255.255.255.0 192.168.8.1

  I have an other W2K3 server (SERVER B) with a single NETWORK (192.168.100.12) card that must be able

  to connect with the fiber switches via tcp/ip. Packets should be routed to this server.

  On that I put in place a permanent route:

  Pei route add 192.168.8.0 mask 255.255.255.0 192.168.100.14

  Everything works very well.

  (Assumes that the SERVER-A and SERVER B are now turned off)

  I'm trying to reproduce this on my VMware ESX Server 3.5upd3.

  ESX server has two NICS, one attached to each of the subnets. I create a virtual machine to replace SERVER-a

  with the same number of network cards and the same IP addresses.

  I then create routes as follows:

  Pei route add 192.168.8.0 mask 255.255.255.0 192.168.100.14

  Pei route add 192.168.100.0 mask 255.255.255.0 192.168.8.1

  PROBLEM: as soon as I add the second route I can no longer ping any server on the 192.168.100.0 subnet.

  This also causes connections to last very long.

  Do I need to implement routing between network adapters ESX scale to make this work?

  If so maybe want the command look like? If not, what could be my problem?

  Thank you for the helpful answers

  If you want to configure your machine as a router, you will need to notify the router is the next hop.  Now, the next machine break is its own interfaces, which will not work.  And since you are running some sort of routing protocol, provide two solutions to exit the server is not a good idea, because he doesn't know that one to use.  It will use 1 for some and another for some.

  Do what you intend (or I think you intend), you must delete the static routes and choose a default route, which will be your next jump.  This should be another router in your environment.  Then, the other servers that you want to route via ServerA, ServerA interface on this segment would remind you.

  Hope that makes sense.

  -KjB

• Share pst file between two users using the same Windows 7 Comp.

  A Windows 7 computer with two user accounts how can I share the pst files & psb between users?

  DONMS wrote:
  > With a computer Windows 7 and two user accounts how can I share the pst & psb
  > files between users?

  Re-ask this question in a forum of Outlook to receive the best advice.

  --

  Bruce Chambers

  Help us help you:
  http://www.CatB.org/~ESR/FAQs/smart-questions.html

  http://support.Microsoft.com/default.aspx/KB/555375

  They who can give up liberty for a little temporary
  safety deserve neither liberty nor safety. ~ Benjamin Franklin

  A lot of people could die rather that thinking; in fact, most do. ~ Bertrand Russell

  The philosopher never killed the priests, while the priest was
  has killed a large number of philosophers.
  ~ Denis Diderot

• How to share both calendars between two different iphones

  My wife and I keep the personal calendars on each of our iPhones. We share Contacts through our main MacBook Pro, but we keep our calendars separately as our two different iPhones. My question is, we'd like to be able to see and share our calendars to the iPhone, but still keep our own separate calendars. (I hope that's clear). Is this possible and what can someone tell me the procedure to do it please. Thank you!

  Hello ovelky,

  Thank you for using communities of Apple Support.

  Take a look at the following article. It explains how to use iCloud for sharing one calendar with others. This sounds just like what you are wanting to do.

  iCloud: share one calendar with others

  Best regards.

• Routing between two VLANs on a switch in series SG300

  I've seen a lot of messages from people with problems of traffic between the two routing VLANS with some complex examples.  Can someone show a simple example for a SG300 switch (in layer 3 mode) to set up the two VLAN and send the traffic between VLANS without an external router?

  VLAN1 10.10.10.0

  VLAN2 10.10.20.0

  I tried to do through the UI and can't seem to make it work.  It seems that it must be very simple, so maybe I'm missing something in the GUI.

  Hi Chris,

  I did 5 minutes of recording that showed how I configured the two VLAN on my SG300 switch and layer 3-switched between the VLANS.

  You have no trouble getting to the GUI, so you will have no difficulty to setup in a few minutes...

  • Be sure to use the latest version of the SG300 package, with a bearable CLI.
  • to save your changes to the configuration at the end of the process.
  • the IP addresses that you create will be the address of default gateway for PC hosts on VLANs specified.
  • Recording can be interrupted at any time to perform configuration operations.

  Recording is now available on the website of the WebEx service. Click on the link below to read:

  https://Cisco.WebEx.com/ciscosales/LSR.php?at=PB&SP=MC&rID=55688352&RKEY=05e1fc5fff0d05da

  Configuration of VLAN

  Monday, October 24, 2011 11:02 New York time

  5 minutes

  Have fun

  Best regards, Dave

• Route between two VPN

  Hi all

  I have searched endlessly around things online and try on the firewall and can't seem to find an answer to this problem. Its probably something really simple under my nose!

  I use an ASA 5510, which currently has some site to site VPN of distinct connections configured, linking to other Cisco devices on customer networks.

  I work from home, so also connect to our network by using remote access VPN (anyconnect) to connect to the network in the data center.

  Just to be clear, here's my amazingly stretched; network diagram

  -------------- ----------------------------------------

  The problem I have is that I can't connect directly from my house to the customer network, I need to RDP in a server in the data center, then from there, I see network clients.

  It routes to be installed somewhere? between VPN? Ive looked in the routing on the firewall options and cand seem to find something that works.

  I have searched for this and cannot find answers, even some sources saying its impossible. Surely not?

  I have put all your remote LAN segment in a group of objects.

  object-group network in REMOTE LANS
  network-object 10.151.30.0 255.255.255.248
  network-object 212.9.3.72 255.255.255.248
  object-network 10.0.21.0 255.255.255.0
  network-object 212.9.20.240 255.255.255.248

  access extensive list ip 10.0.20.0 outside_nat0 allow 255.255.255.0 object-group REMOTE LANS
  access extensive ip list outside_nat0 allow REMOTE object-group-LANS 10.0.20.0 255.255.255.0

  permit same-security-traffic intra-interface

  NAT (outside) 0-list of access outside_nat0

  Let me know the result

  Thank you

• BlackBerry smartphones I want my BBM back! BBM contacts switched between two phones I own, my wife and me

  Hey, my wife's friends are nice, but I can't be in their discussions... I have 2 bb Torch 9800. For no apparent reason about 3 months ago the bbm contacts exchanged between them without any reason. I've been in contact with my phone provider, and they are perplexed and said that it is a problem of bb... How can I get the bbm is switched back to good phones?

  I tried to remove and reinstall applications, same old contacts...

  Note: I share the same e-mail address on both phones, this could be and question? When I got the phones of MTS, a few years ago, they said it was very good and quite work very well to the top until there are a couple / few months.

  Hello and welcome to the community!

  Sharing the same e-mail address is no problem... e-mail systems is generally accessed from multiple customers, and the application of enamel on the BB is just another type of e-mail client.

  But, if you meant that you share the same BBID on both devices, then it indeed is probably the cause of the problem. It is inadvisable to associate a BBID to more than a SmartPhone BB. Strange things can happen, including the tangle of BBM contacts, as has happened to you.

  Since BBM7, BBM contacts are not stored on the device itself... on the contrary, they are stored "in the cloud" with the BBID. Before BBM7 (indeed, "a couple of years"), the BBM contacts were stored on the device itself and therefore would not mingle if a BBID has been shared between several BB devices.

  Here's what you need to do:

  1. Decide which of the two devices will retain the existing BBID
  2. Manually clean the BBM contacts to reflect only what desires this device
  3. On the other BB, you need to prepare by making a full backup of the device, because the "fix" will wipe
     • See the link in my sig auto on this post for instructions to complete backup
  4. Once you have this backup, you should separate this another BB the BBID existing and create a new brand for the single device
     • KB26694 How to change the BlackBerry ID on a BlackBerry smartphone or BlackBerry PlayBook Tablet
  5. Once this is done, you can switch to manually re-create all BBM contacts on the 2nd device (no, there is no way to automate this process for you)

  Good luck!

• Routing between two remote sites connected over the VPN site to site

  I have a problem ping between remote sites.  Now the Cryptography and no nat ACL's for different sites just to affect traffic between the remote site and main site. I tried to add roads, adding other subnets to the crypto and no. ACL Nat at the remote sites... nothing worked.  Any ideas?

  Main site:

  192.168.100.0 - call manager / phone VLAN

  192.168.1.0/24 - data VLAN

  Site 1:

  192.168.70.0/24 - phone VLAN

  192.168.4.0/24 - data VLAN

  Site 2:

  192.168.80.0/24 - phone VLAN

  192.168.3.0/24 - data VLAN

  Main router

  Expand the IP ACL5 access list
  10 permit ip 192.168.1.0 0.0.0.255 192.168.70.0 0.0.0.255
  20 ip 192.168.1.0 allow 0.0.0.255 192.168.4.0 0.0.0.255
  30 permits ip 192.168.100.0 0.0.0.255 192.168.4.0 0.0.0.255
  IP 192.168.100.0 allow 40 0.0.0.255 192.168.70.0 0.0.0.255)
  50 permit ip 10.255.255.0 0.0.0.255 192.168.70.0 0.0.0.255
  Expand the IP ACL6 access list
  10 permit ip 192.168.1.0 0.0.0.255 192.168.80.0 0.0.0.255
  20 ip 192.168.1.0 allow 0.0.0.255 192.168.3.0 0.0.0.255
  30 permits ip 192.168.100.0 0.0.0.255 192.168.3.0 0.0.0.255
  IP 192.168.100.0 allow 40 0.0.0.255 192.168.80.0 0.0.0.255

  Expand the No. - NAT IP access list
  10 deny ip 192.168.2.0 0.0.0.255 192.168.70.0 0.0.0.255
  20 deny ip 192.168.200.0 0.0.0.255 192.168.4.0 0.0.0.255
  30 deny ip 192.168.2.0 0.0.0.255 192.168.80.0 0.0.0.255
  40 deny ip 192.168.200.0 0.0.0.255 192.168.3.0 0.0.0.255
  320 ip 192.168.1.0 allow 0.0.0.255 any
  IP 192.168.100.0 allow 330 0.0.0.255 any

  Site 1:

  ACL5 extended IP access list

  IP 192.168.70.0 allow 0.0.0.255 192.168.1.0 0.0.0.255

  ip licensing 192.168.4.0 0.0.0.255 192.168.100.0 0.0.0.255

  IP 192.168.70.0 allow 0.0.0.255 192.168.100.0 0.0.0.255

  ip licensing 192.168.4.0 0.0.0.255 192.168.1.0 0.0.0.255

  IP 192.168.70.0 allow 0.0.0.255 10.255.255.0 0.0.0.255

  No. - NAT extended IP access list

  deny ip 192.168.70.0 0.0.0.255 192.168.1.0 0.0.0.255

  refuse the 192.168.4.0 ip 0.0.0.255 192.168.100.0 0.0.0.255

  deny ip 192.168.70.0 0.0.0.255 192.168.100.0 0.0.0.255

  refuse the 192.168.4.0 ip 0.0.0.255 192.168.1.0 0.0.0.255

  deny ip 192.168.70.0 0.0.0.255 10.255.255.0 0.0.0.255

  IP 192.168.70.0 allow 0.0.0.255 any

  ip licensing 192.168.4.0 0.0.0.255 any

  Site 2:

  ACL6 extended IP access list
  IP 192.168.80.0 allow 0.0.0.255 192.168.1.0 0.0.0.255
  ip licensing 192.168.3.0 0.0.0.255 192.168.100.0 0.0.0.255
  IP 192.168.80.0 allow 0.0.0.255 192.168.100.0 0.0.0.255
  ip licensing 192.168.3.0 0.0.0.255 192.168.1.0 0.0.0.255
  IP 192.168.80.0 allow 0.0.0.255 10.255.255.0 0.0.0.255
  No. - NAT extended IP access list
  deny ip 192.168.80.0 0.0.0.255 192.168.1.0 0.0.0.255
  deny ip 192.168.3.0 0.0.0.255 192.168.100.0 0.0.0.255
  deny ip 192.168.80.0 0.0.0.255 192.168.100.0 0.0.0.255
  deny ip 192.168.3.0 0.0.0.255 192.168.1.0 0.0.0.255
  deny ip 192.168.80.0 0.0.0.255 10.255.255.0 0.0.0.255
  IP 192.168.80.0 allow 0.0.0.255 any
  ip licensing 192.168.3.0 0.0.0.255 any

  What should I do for these two sites can ping each other?  I looked through the forums but can't seem to find someone with a similar problem, which has received a definitive answer.

  Thanks in advance!

  Hi, I assume that you need site 1 and 2 to communicate with each other via the main site right? If this is the case, then you need to set add the following lines to your ACL crypto:

  Main router

  Expand the IP ACL5 access list

  IP 192.168.80.0 allow 0.0.0.255 192.168.70.0 0.0.0.255

  IP 192.168.80.0 allow 0.0.0.255 192.168.4.0 0.0.0.255

  ip licensing 192.168.3.0 0.0.0.255 192.168.70.0 0.0.0.255

  ip licensing 192.168.3.0 0.0.0.255 192.168.4.0 0.0.0.255

  Expand the IP ACL6 access list

  IP 192.168.70.0 allow 0.0.0.255 192.168.80.0 0.0.0.255

  IP 192.168.70.0 allow 0.0.0.255 192.168.3.0 0.0.0.255

  ip licensing 192.168.4.0 0.0.0.255 192.168.3.0 0.0.0.255

  ip licensing 192.168.4.0 0.0.0.255 192.168.80.0 0.0.0.255

  Make sure you add these lines before the last permit

  Expand the No. - NAT IP access list

  deny ip 192.168.80.0 0.0.0.255 192.168.70.0 0.0.0.255

  deny ip 192.168.80.0 0.0.0.255 192.168.4.0 0.0.0.255

  deny ip 192.168.3.0 0.0.0.255 192.168.70.0 0.0.0.255

  deny ip 192.168.3.0 0.0.0.255 192.168.4.0 0.0.0.255

  deny ip 192.168.70.0 0.0.0.255 192.168.80.0 0.0.0.255

  refuse the 192.168.4.0 ip 0.0.0.255 192.168.80.0 0.0.0.255

  deny ip 192.168.70.0 0.0.0.255 192.168.3.0 0.0.0.255

  refuse the 192.168.4.0 ip 0.0.0.255 192.168.3.0 0.0.0.255

  Site 1:

  ACL5 extended IP access list

  IP 192.168.70.0 allow 0.0.0.255 192.168.80.0 0.0.0.255

  ip licensing 192.168.4.0 0.0.0.255 192.168.80.0 0.0.0.255

  IP 192.168.70.0 allow 0.0.0.255 192.168.3.0 0.0.0.255

  ip licensing 192.168.4.0 0.0.0.255 192.168.3.0 0.0.0.255

  Make sure that these lines are added before the last permit

  No. - NAT extended IP access list

  deny ip 192.168.70.0 0.0.0.255 192.168.80.0 0.0.0.255

  refuse the 192.168.4.0 ip 0.0.0.255 192.168.80.0 0.0.0.255

  deny ip 192.168.70.0 0.0.0.255 192.168.3.0 0.0.0.255

  refuse the 192.168.4.0 ip 0.0.0.255 192.168.3.0 0.0.0.255

  Site 2:

  ACL6 extended IP access list

  IP 192.168.80.0 allow 0.0.0.255 192.168.70.0 0.0.0.255

  ip licensing 192.168.3.0 0.0.0.255 192.168.70.0 0.0.0.255

  IP 192.168.80.0 allow 0.0.0.255 192.168.4.0 0.0.0.255

  ip licensing 192.168.3.0 0.0.0.255 192.168.4.0 0.0.0.255

  So make sure that these lines are added before the last permit

  No. - NAT extended IP access list

  deny ip 192.168.80.0 0.0.0.255 192.168.70.0 0.0.0.255

  deny ip 192.168.3.0 0.0.0.255 192.168.70.0 0.0.0.255

  deny ip 192.168.80.0 0.0.0.255 192.168.4.0 0.0.0.255

  deny ip 192.168.3.0 0.0.0.255 192.168.4.0 0.0.0.255

  So you're saying good enough your routers with these definitions which will be reached via one main remote sites (sites 1 and 2).

  I would like to know if this is what you need.

• Routing between two Vmware images (mode single host) running on mac 0sx 10.5.7

  Hello

  I have two VMware images: a windows 2003 server and another company of red hat running on my mac with vmware fusion. Two of them are to be only one host mode and I manually assigned a static IP address to those servers to vmware. Thier is a situation that I can't change the static IP address.

  Vmserver1: 192.168.1.102

  255.255.255.0

  192.168.1.1

  Vmserver2: 10.2.18.28

  255.255.255.0

  10.2.18.1

  How to define two communications between these two servers. (sending between two servers).

  Thanks in advance!

  Happy the ifconfig worked for you. This is the approach I usually take too.

• Cannot use Internet on the VPN connection

  Hello

  I used a cisco customer version 4.0.3 installed on my laptop to connect to the VPN server.

  When my VPN client is connected to a remote VPN server via a wired LAN to my site office, I can't use the Internet at the same time. I have him this might not be possible unless "split tunnel" is allowed in the side server. When I connect to the server via the Wi - Fi network in the same office, I can use the Internet. It made me confused, so I checked the IP address of my network bridge by using the command 'ipconfig '. He showed the two IPS 10.100.128.1 and 10.100.128.2 for the wireless network connection and a single IP 10.69.225.70 for the wired network connection.

  How can you explin the situation of the two above? Two default gateways allowed me to use the Internet when my client is connected to the server through the network wi - Fi? The disable "split tunnel" function in the server VPN has blocked me form using the Internet, the connection to the server via the cable network? I don't think so. Why?

  When my client is connected to the VPN server over the network domestic Wi - Fi home that has only a single default gateway, 192.168.0.1. I have no problem with the use of the Internet. How can you explain this bizarre situation? I really want to use Internet through a wired network and wireless at the other site office who have only one gateway respectively. Could you explain that?

  Thank you very much... Jae

  You are welcome, I hope we can fix it all.

  ComboFix set malware entries that could corrupt your browser for a malfunction. WinSockFix to fix corruptions that may have caused by the VPN software. But I'm not a type of corruption is likely to not do not work and https http to work.

  Now, let me understand the current issue. You cannot connect to the internet even the VPN is disconnected correct?

  I have a few questions and need of some outputs of diagnosis

  (1) I think that you are in a hotel. Using wireless? Can it be quota restrictions by the hotel management?

  2) connect via VPN. You have established the connection, my neighbors network at the office with the right button > properties. Now, right-click of Cisco VPN Adapter, and then click on repair. And then disconnect your VPN client

  (3) once you disconnect a VPN, do the repair, even for your Local network connection or a wireless connection. The VPN is disconnected, run the following in the command line

  Nslookup

  www.Google.com

  then run

  tracert 64.156.132.140

  then run

  impression of the route

  And after the output of these commands here.

• I want to use bookmarks, but have no synchronization haven number had one for over a year. could never recover.

  I do like Firefox because I spent the last 20 minutes, just trying to report so that I can get to favorite and history which does not include the 20 minutes, I go through FAQ I don't care about the old sync number that I use to have, and I don't care if I get a new number from the sink , but I want to be able to use all of the features in Firefox, why would you not add these things to Firefox so that everyone can use and then decide to add something to it and see if they want to not a mandatory thing to hunt for more than an hour trying to figure how to do it just so you can get the basic features of the normal web browser

  If you want to use Firefox Sync to synchronize bookmarks between your different devices, but have not ever used? How can I set up Sync on my computer? can help

• When the computer starts first to the top, a window titled "run as" the question "which user account do you want to use to run this program?

  Original title: which user account you want to use to run this program?

  I use a computer that is running Windows XP SP3. Recently, when the computer starts first to the top, a window will appear titled ' run as ' the question "which user account do you want to use to run this program?" with two radio buttons. The default selection is "Current user" and there is a checkbox to "protect my computer and data from unauthorized program activity. The other button is for "the next user. I have to click 'OK' before you can run any programs.

  There is only one user on the computer. Why has this window began to appear and can I get rid of him?

  Hello

  That you recently installed which triggers this popup message initially upwards?

  You can try to perform a clean boot and check if it helps.

  A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  How to configure Windows XP to start in a "clean boot" State

  Note: Make sure that you put the computer to a Normal startup once you have completed troubleshooting.