wanted to build a vi to simulate the hold on a Panel button.

Similar Questions

• I want a music video to play when the user hovers over a button

  Hello
  
  I want a music video to play when the user hovers over a button, but I don't want the music to start again when the user hovers over the button again. I want him to play for its entire length, does not restart if the user accidentally will be on it once more.
  
  Thanks in advance for any help.
  
  

  You can use:

• Cannot find NI0DAQmx devices on the network. Test Panel button grey

  Hello

  I have a Dell than T710 Win Server 2008 R2 64-bit. NidaqMX 9.3 is installed. The dialog box search for network OR-DAQmx devices cannot find my NI ENET-9163 carrier with a card NI 9215. This card has a static IP address in the same subnet as the LAN of the PC port. I ping the device.

  However in the search network OR-DAQmx devices dialogue box I can add the Board manually by specifying the IP address. This seems to half work as long as it saves the map MAX, but the test panels button is grayed.

  I installed Nidaq MX 9.3 on my win 7 64 bit laptop and I can find the card properly and test it. Clearly there is something wrong with the config on the Dell software, but I have no idea what. Any help is appreciated. I stumbled on, IP addresses etc. I also disabled the 3 other network ports on the Dell server in case that is the question.

  Thank you

  Andrew

  Hello Andrew,.

  I could do some tests on our Windows 2008 R2 server. I was able to replicate this but not as easily as you did. We have 2 network adapters on that server. We have solved this problem is to do the following:

  1. disable IPv6 IP addressing all the ports of the network.

  2. change the metric of the Interface on the network adapter. We have high, so a value of 50. You can get this metric by going into the properties of your network card > your IPv4 properties > advanced on the general tab > UN select Automatic metric and replace with static. (the entries are 1-60). Do this for all of your network adapters. Given that we have this setting that we have never seen the question re occur.

  We also checked that it doesn't happen at all on the new cDAQ-9181 chassis. This chassis is intended to replace the ENET-9163. If it is possible for your upgrade I would recommend this option. You should be able to work with your local sales channel to get one to test with. We have 20 + 9181 in this system and have never seen the issue of not being able to Max commonality to the chassis.

  Let me know your results to adjust the parameters I mentioned above.

  Thank you!

  Corby

  CDAQ PES of R & D network

• Simulate the Cache Buffer Chain latch

  Hi all
  
  Can simulate CBC latch scenario, I want to say I want to create test cases to simulate the latch of the CBC and dig in for different solutions to reduce the latch of the CBC.
  
  It would be great if someone can give me the test case, link or idea.
  
  -Yasser
  
  Published by: YasserRACDBA on December 16, 2009 17:42
  

• I want to build a form with radio buttons to customers limited checking all the options.

  I want to build a form with radio buttons to customers limited checking all the options. I have a range of products and to quote accurately, I want to get specific information.

  If I get this, what you want to display the shape options to specific customers, not to all the viewers of the site?

  You must create a secure area where authorized viewers can connect and view the form with all the options, form itself we can not set up since what few customers are going to see other options and others are going to see another.

  This is possible since the end of your accommodation. Or if you are using Adobe server for hosting, then you can create profiles for clients and then set up another form altogether to achieve this goal.

  Thank you

  Sanjit

• I want to build a pc for better video editing with the soft first Adobe pro and Adobe after effect. Should what kind of material I buy for it. If you suggest me pls.

  I want to build a pc for better video editing with the soft first Adobe pro and Adobe after effect. Should what kind of material I buy for it. If you suggest me pls. my budget is about $2500

  You will have problems in the construction of a 99 X system for this budget. You need 32 GB of ram if you do that will be a large part of the cost with DDR4 right now. If you have a room on the X 99 budget would certainly be the way forward. The 5960 X is the best processor out right now but $1100 will probably push your budget. The 5930 K would still work and a much better price for your budget. I suggest: 970GTX with this budget as well. Forget the Xeon V3. They are out of your budget and not worth the price with this budget in mind. You can get a system much better with the I7 Haswell E chips.

  Eric

  ADK

• Simulate the PXI-1033

  Good afternoon

  I need some clarification on the simulation of PXI via MAX.   I have several PXI modules and a PXI-1033 (integrated into the PCIe MXI) chassis on command.   As they will take several weeks to arrive, of course, I want to simulate these devices and to start building screws

  If I understand correctly the information contained in the knowledge base and forums, all I have to do is to simulate modules PXI themselves in MAX and nothing to simulate PXI-1033 chassis.

  Is this correct?   Guarantees as to any would be greatly appreciated!

  Sincerely,

  Zach

  Hey Zach,.

  You are right. We cannot simulate a PXI-1033 chassis, but because it's just an expansion chassis, there is no need to. You can simulate the modules themselves in MAX under DAQmx devices and then you should be able to start writing code.

  Good luck and thanks,

  Ryan

• Simulate the entry

  Hello

  To check my software, I want to simulate some signals on the entrance of the simulated NIDAQmx Council. Is this possible?

  I created the jury simulated in NI MAX, but I know not how to simulate the signal on the inputs and run my software (in C language) in order to acquire the data.

  Thank you

  Theinput signal of the simulated device is built-in, you can't change it. It is better to write your own piece of code that simulate the signal.

• Use the toggle button to simulate the Ctrl key now

  Hello

  I saw someone asked something very similar before, but nobody seemed to know the solution.

  I was wondering if it is possible to use a toggle button to simulate the CTRL key now, the idea being that the user could then zoom in on a rectangle of their choice on a field without having to press the button themselves. I know that you can use the FakeKeystroke function to simulate support that the key however is possible that it may be held?

  Thank you

  I forgot one thing. You must handle the case when you have a real EVENT_DOUBLE_CLICK. In this case, you don't want to reset the keyboardState. Here's the modified code.

  char oldKeyState [256] = {0};
  
  char newKeyState [256] = {0};
  
  int isFakeDouble = 0;
  
  Zoom CVICALLBACK int (int, int int event, control panel,
  
  		void * callbackData, int eventData1, int eventData2)
  
  {
  
  	HWND hwnd;
  
  	toggleButton int = 0;
  
  	switch (event)
  
  	{
  
  		case EVENT_LEFT_CLICK:
  get the current state of the keyboard
  
  			GetKeyboardState (oldKeyState);
  
  			get the State of the toggle button
  
  			GetCtrlVal (panelHandle, PANEL_TOGGLEBUTTON, & toggleButton);
  If (ToggleButton)
  
  			{
  
  				create the new copy of the keystate
  
  				memcpy (newKeyState, oldKeyState, 1);
  Active control key.
  
  				newKeyState [VK_CONTROL] = 128;
  
  				SetKeyboardState (newKeyState);
  generate left mouse button events that will be holding the CTRL active
  
  				SetActiveCtrl (panelHandle, PANEL_GRAPH);
  
  				GetPanelAttribute (panelHandle, ATTR_SYSTEM_WINDOW_HANDLE, (intptr_t *) &hwnd);)
  
  				isFakeDouble = 1;
  
  				SendMessage (hwnd, WM_LBUTTONDOWN, 0, 0);
  
  				isFakeDouble = 0;
  
  			}
  break;
  
  		case EVENT_LEFT_DOUBLE_CLICK:
  mouse event generated will be taken as a double click. restore the old state of the keyboard
  
  			If (isFakeDouble)
  
  				SetKeyboardState (oldKeyState);
  break;
  
  	}
  
  	return 0;
  
  }

• Trying to simulate the device USB-6366 (without success)

  I read through the tutorials DAQmx and MAX about the simulation of the device, but I can't yet find a way to effectively simulate the acquisition and generation of a signal using a device USB-OR-6366.

  I am a (given at the entrance of this VI) signal using DAQmx Write and then use DAQmx Read to read the signal captured from the internal memory of the card (which has a buffer of 32 MS). To do this, I created a task with DAQmx I feed in the writing block.

  I know that the approach is most likely wrong, but I can't understand not just how to do this in a simple way and documentation of NOR is anything but simple. All I want is to

  (a) test using 2 digital inputs to capture this signal by the device and then read what she has gained from its internal buffer

  (b) send the same signal to 2 digital outputs the signal output again.

  See you soon

  Yes! the simulation is designed to allow you to write a program and check that it works theoretically even if you do not have the material physically available. It has no interface programming to influence on the what the reading functions will return simulated data. And write the function has no notable effect anywhere, working as a receiver of data in nirvana. It is always useful because you can test software without getting all kinds of errors on the non existing hardware access attempt, but it has its limits, of course. However, a programming interface for manipulating that which and how the data are simulated, while it would be a very interesting feature, is almost certainly to complicated not only to implement but also to use.

• Simulate the structure of the event in the LabVIEW base?

  I have a basic version of LabVIEW (v8.6) who doesn't have the structure of the event. I found it was quite embarrassing monitor the status of several controls (action after clicking a control depends on the State of the other control (s)). Especially if I want to add another function (control), the effort exponentially increase with the current number controls

  I had an idea to simulate the structure of the event using "shift register. First, I will provide all the values for the controls in a cluster. Then I'll put the cluster in a while loop and compare the value of the cluster to its previous value (xor the registry change). If the result of the comparison is false (none of the control is changed), the program moves to the next iteration. If the XOR result is true (one of the control has changed), then the program goes into code (it will pass what control has changed and the entire cluster) event management. So for each change of control, we can write an independent code to process the event. After processing of the event, the event was allowed.

  Here are some of my ugly code currently used to monitor multiple controls. And I think rewriting using above idea so there is less chance a hiden bug.

  Comments, suggestions?

  I'm not quite sure what I'm looking for on your photo of your block diagram because it seems that only the lower quarter right in your code.  I would do the following to detect a change in a cluster without the structure of the event control:

  

  The basic package include the notifications than us?  You can put your "event management" in another thread by this method:

  

  The advantage here is your main loop of the program is not "bogged down" every time that a change in your cluster held.  It also allows to separate the code so that it is cleaner.

  Hope that helps!

  -Fisher

• Simulate the button click in panels of void

  Hi all

  I want to simulate click for buttons (with an action mechanical latch) located in sup VI Panel in order to trigger its action. But I could not do this in the way I can simulate a click for all other buttons in the main VI. I have attached a sample program to explain my problem, please let me know what is my mistake.

  Thanks in advance,

  Roger of S.G.Sree.

  just a small mistake.

  Jim you missed it.

  You can go there.

• How to simulate the change of sim card

  Hi friends

  I want to simulate the functionality of changing the sim. If I'm erasing all data on mobile, then I lost all data. Is there a solution to implement the scenario of change of sim card.

  You can simulate the change of SIM card on Simulator-

  Steps for BB JDE-

  
  

  1.) go to the Menu bar - > edit-> preferences

  The Simulator 2 tab.) -> Network tab->

  # ICCID (GPRS) / ICCID override (GPRS)
  

  # IMSI (GPRS) / IMSI override (GPRS).

  Enter here any value in the format - www.xxx.yyyy.zzzz (e.g. 5600.5478.02145.121)

  3.) click apply. Close.

  4.) now when you run the Simulator, it generates a warning.

  Given IMSI (5600.5478.02145.121) is longer than the maximum length (15).

            Click on continue.

  Steps for Eclipse-

  1.) select your project in the Package Explorer-> right click-> Debug as ->Debug Configurations ->

  2.) select DebugServer from the left pane of the window.

  (3.) the right side of the pane, there are four tabs-> go to the Simulator.

  4.) be that cannot change default Simulator, if we are to make a new profile.

  5.) don't forget the new profile is selected. Now, select network tab.

  6.) steps 2, 3 & 4 above.

  
  

  Now, it will give u a simulation of change of default SIM card IMSI value is 666666.01.234567.8

  Thank you

  Kanak Sony
  

• Hello, I want to build several video clips with more than 500 images (pictures) of each clip. I need to apply a different video transition effect to each photo. It might even be random effects. I see that I can apply a unique to all p transition effect

  Hello, I want to build several video clips with more than 500 images (pictures) of each clip. I need to apply different transitions video effects by alternating each photo. It could be random effects. I see that I can apply a unique pictures transition effect at the same time, but how to apply different transitions not one by one? I could do a clip applying different transitions manually as I wish between hundreds of photos, but I would like to be able to repeat all the transitions of a new video by changing only the photos. Is this possible? Or a tool to apply random transition effects between photos? Or a way to automate the actions to apply different transitions similar to what we can do in Photoshop? Thank you!

  But how to apply different transitions not one by one?

  You can not.

  If you wish to make a slideshow with all the transitions better fantasies use something like Pro Show gold.

  Alt drag window project replaces clip/still on the timeline.

• Simulate the wind around a player

  I have a video of me on my green screen, and I am trying to simulate the wind around me, like a fall to the cheese. I want it to look like this: Dear Ryan - stop videos post! - YouTube is a way to do it with any third party plugins?

  I think there's some involved roto and directional blur and or a radial blur together to zoom. Something like that might work. Just a blue background United added so you can see the blur. Here is a sample project using a frame of their video... Dropbox - windEffect.zip

  

  Note that the top layer is the actor without any blur, blur is behind. In a typical production environment I create the key and then return a DI (digital intermediate with an alpha using a lossless codec) and the DI allows you to create composite.