Why the calendar shows only 30 seconds of my audio clip of 2 min?

Similar Questions

• Duration of the slide show CS5 does not again refresh audio clip

  In a slide show, complete with 'Fit audio slideshow DURATION' checked (duration 00; 19; 32-24), I decided to replace the audio with a composition more short (00; 10; 00; 22). With the original audio clip erased and the new added audio clip and the 'slide show audio TIME Fit' checked, slide durations recalculated so that the last slide has a 00 exit point; 10; 00; 22 but the duration of the slide show is 'stuck' 00; 19; 32; 24. the end action takes place to return to the menu, but when the last slide goes black (at 00; 10; 00; 22) keeps him slide show running with a black screen, probably all the way to 00. 19; 32 24 before it hits the end action, even if I did not let it run again at this point. I shot 'Fit slideshow to audio duration' then turn it on again, in the hope that it will recalibrate at 00; 10; 00; 22, but the length does not change. Help, please!

  Try to play with these ideas:

  Uncheck "Fit to Audio duration slideshow."  (As you probably now it have anyway).

  On the slide show tab basic properties, set the duration of the slide to zero.  Now, what is the length of the slide show?  The length of the audio new or old?

  Or, something great (so I think that the total is more audio length) on the duration of the slide.  What is the length of the slide show?

  Search now "Fit slideshow / audio.  How long is it?

  I had the same symptom as you did (audio plays beyond the end of the blades) when the durations of slide added unless the audio length and 'Fit audio slideshow' was unchecked.

• My account calendar shows only not in the calendar app

  Hello

  I have a problem with the calendar (version 18.6.A.0.1). When I open it, the calendar shows only birthdays my contacts, but I don't see my owncloud calendar, even though I can see and synchronize in the android account manager.

  In fact, I disabled the application of storage calendar, then created the resource calendar and finally turn back the calendar again storage application. So storage of schedule was a little lost after him.
  This problem is resolved by the deletion and recreation of the resource.

• I do the buttons on the taskbar show only icons, but I wanted it back.

  what I did before the buttons on the taskbar show only icons is as follows:

  Start > run > regedit > HKEY_CURRENT_USER\Control Panel\Desktop\WindowMetrics

  There, you must find the one "REG_SZ" with the name "MinWidth".

  (write without quotes)

  If you do not create one in your won with the name "MinWidth".

  (write without quotes)

  Once you find it double click on it and set the number 56 then click ok and close.

  Registry and restart your computer.

  
  

  
  

  ---------------------------------------------------------------------------------------------------------

  
  

  minWidth had-255, I changed it back, but the taskbar do not change back. What should I do now?

  
  

  Here's the screen shot a http://oi51.tinypic.com/15dl2pz.jpg link

  
  

  
  

  
  

  
  

  
  

  Use this tutorial: go to an Option and take #2 - restore the task bar button

  http://www.Vistax64.com/tutorials/191509-taskbar-icons.html . for the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.

• Sidebar calendar shows only orange... not the data either

  My calendar loads in the bar but shows only an orange page.  There is nothing else... no data at all. I tried the tools without result; It only allows me to remove the calendar.

  If it's just the calendar gadget that gives you trouble, you should be able to simply re - record a single. DLL to rectify a calendar gadget that looks like this,

  
  First remove the existing calendar gadget, and then click Start or press on the key and type cmd but don't hit. Search for CMD in the list above and right-click and select run as administrator. Confirm the warning of the DSU and provide credentials if requested.

  The open command window, type.

  Regsvr32.exe vbscript.dll
  ... and click on . You will receive a popup confirmation as follows,

  

  Restart the computer and add the calendar on the desktop gadget. It should now work as follows,

  

  If the gadget still does not work, you can try a much more aggressive approach to my solution on this page.

• Gadgets calendar showing only as a blank page when I add, why is this

  Try adding calendar Gadgets, but it will only show a white orange flip page.  How can I get the calendar and date to show?

  Hi MargaretRobertson,

  1. you remember to make changes to the computer before this problem?

  This problem may occur because of missing script execution recording. Register the VBScript.dll file that a command admin could solve the problem.

  Step 1:

  a. Open command prompt by clicking on start prompt by typing in the start search box.

  b. right-click on command prompt and select run as administrator.

  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  c. type the following command and press ENTER.

  Regsvr32.exe vbscript.dll

  d. restart the computer and check.

  Step 2:

  If you're still having problems, then you can try to run a SFC scan and check.

  This problem may occur if a system file is missing or damaged.

  You can refer to the method-the System File Checker tool in the following article:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Hope this information is useful.

• Why the Favicon shows up only on the Page of Index?

  Hello. I hope you have a good day!

  First of all, I am aware that this question has been asked and answered before many times. However, when I search the Forum with the key word "favicon", nothing appears. I'm assuming that Adobe has erased some of the former subjects of the forum for the purpose of storage or something to that effect.

  I made a website for my friend's father: www.socialclubofjupiter.org

  For some reason, the favicon appears only on the index page. I think it's because I put the coding for the favicon (< link rel = "shortcut icon" href = "favicon.ico" > ") on a model and applying the model to each page. I know this because when I use for each page individually without the use of code templates, everything worked perfectly. I even tried to put the favicon in the models one folder placed this coding rather (< link rel = "shortcut icon" href = "Templates/favicon.ico' >"), however, it still does not work outside the index on Google Chrome page.

  What I am doing wrong?

  Thank you in advance.

  Hello

  your browser (most of our browsers) should be convinced first to show! To display the icon, may be you have to do that too:

  Clear your caches!
  Check with another browser, the new icon will be there.

  Or / and:

  -If set, remove the bookmark to the page, or recreate the bookmark.
  -Browser to quit
  -Empty the Options of the Internet of temporary Internet files
  -Clear history
  -Delete everything in general, where the browser remembers visited websites.
  -Restart
  -Clear site visit
  -Disable again bookmark

  Hans G.

  P. S.

  Download the file favicon.ico to the root of your server.
  Insert this line of code between theTags on your home page or index.html, here, you can use:

  or
  or
  (I use it)
  

• Why Flash graphic showing only 15 bars

  Hello
  
  I created a flash graphic, a 2-d column chart, but it shows only 15 columns, I checked that this query returns more than 20 lines.
  
  When I created a chart sectors with the same query, it too showing 15 pieces with one total extra, "The other" by calculating the other remaining lines.
  
  Can anyone tell why bar and pie chart display all the lines?
  
  Thank you
  -Smith

  Hello

  Go to the attributes table and click Edit next to you series in the section "Series of cards.

  Change the value of lines max here.

  See you soon

  Ben
  http://www.munkyben.WordPress.com
  Don't forget to mark the answers useful or correct ;)

• Why the temperature shows on my watch always different temperature on the watch of my husband when they use the same application?

  Why the temperature still showing on my watch shows a different temperature than on my husband watch when they both use the same weather app?

  Hi Jodie

  If you are each using the weather app (which is included in the framework of the iOS and watchOS), the following steps can help (followed by each of you):

  • On your iPhone, in the weather app:
    • If using anything other than the current location (which is included by default), make sure you have each added to a common location / city.
    • To add another location, select the icon «+»
  • On your iPhone, in the application of the watch, go to: My Watch (tab) > weather > default City > make sure you have each selected at the same location (for example: place of current residence or Mount Laurel).
  • On your iPhone, go to: settings > privacy > location Services:
    • Ensure that the location service is enabled;
    • Make sure Apple Watch is face value while it helps;
    • Check that the weather is set to always;
  • On your iPhone, go to: settings > general > background App update:
    • Check that the bottom App Refresh is enabled.
    • It can also help to activate the setting for the weather.
  • For optimal performance of your watch, keep the Bluetooth and Wi - Fi enabled at all times on your iPhone:
    • iPhone: settings > Bluetooth - on.
    • iPhone: settings > Wi - Fi - on.

• Upgrade memory satellite A110-103 - the Bios shows only 1 GB of RAM

  {color: #000000} Dear Forum Toshiba,

  I own a Toshiba Satellite A110-103 (PSABE6) bought in 2006 of the Belgium.
  I have trouble about an upgrade of RAM for this laptop. The laptop was originally a Samsung 512 MB of RAM.
  I tried to upgrade the RAM to its maximum capaity supported 2 GB.
  I bought and installed 2 Kingstone SODIMM 1 GB Value Ram DDR2 PC2 4300 units compatible with the laptop, but

  in the BIOS, I see only 1 GB of RAM.
  I tested each RAM separately and they work very well. The problem is that when I install in my

  locations of the laptop, my BIOS sees no Ram.Instead 2 GB 2 GB, it shows only 1 GB. I updated my BIOS for more later

  version 1.70 (for XP), but the laptop continues to show only 1 GB.

  I tested the RAM separately:
  -inserted only 1 stick in the drive and the pc started ok showing 1 GB of RAM
  -then I inserted the same stick in another location and it also worked well showing 1 GB of RAM
  - then I checked another unit of the RAM in the same way and worked well
  -When I try to put 1 GB of Ram and the old 512 MB RAm the BIOS correctly showed the new value of 1.5 GB
  -i also checked the other 1 GB of ram and the old 512 MB of ram and showed good again in the Bios with the value of 1.5 GB
  - but when I tried to put the 2 ram set units to obtain the BIOS only detected 1 GB 2 GB.

  Here's the description detailed 1 GB modules that I try to install:

  SLOT #1
  The module size: 1024
  Band Max bandwidth: PC2-4300(266Mhz)
  Manufacturer: Kingston
  Reference number: 9905293 - 0.14A00LF
  Serial number: 6ACC0C46
  Frequency: 200-266
  CASE # standby time: 3,0-4,0
  RAS # for CASE #: 3-4
  Tras:9 - 12
  TRC: 12-16
  Voltage: 1, 8V - 1, 8V

  SLOT #2
  The module size: 1024
  Band Max bandwidth: PC2-4300(266Mhz)
  Manufacturer: Kingston
  Serial number: AD0CCE10
  Frequency: 200-266
  CASE # standby time: 3,0-4,0
  RAS # for CASE #: 3-4
  Tras:9 - 12
  TRC: 12-16
  Voltage: 1, 8V - 1, 8V

  What should I do?
  Help, please!

  It IS concerning.
  Marius Militarescu

  [email protected]

  {color}

  I think the problem is that the two s of RAM are not compatible, but it is not explained to me because use you two identical modules.

  In your case I return the RAM to the computer dealer and say the modules work together in your notebook, but your laptop definitely supports 2 GB of RAM.

  I think that there is no other way because you have updated your BIOS to the latest version.
  Here is the part number for RAM Toshiba compatible:
  1 GB OF DDR2 400/533 (PA3411U-1M1G)

• Why the calendar not storage my dates?

  White MacBook 2.4 GHz Intel Core 2 Duo, OS X 10.9.5 end of 2010:

  When I open the calendar, and add a new entry, calendar stores not my nomination, but only when I repeat, schedule keep the contribution!

  Hello there, barcimarci.

  Looks like you are having problems with the calendar by keeping your initial entry when you create one from scratch. One thing we might want to try is to see if it behaves in the same way in a new user. To do this, the following Knowledge Base article offers the process on how to achieve this:

  How to test a question in another account on your Mac.

  Before you try a different user account

  If you see unexpected behavior on your Mac to first try the following steps:

  Try to search the base knowledge of Apple for the specific symptom or an alert message you see. There could be more simple measures that you can take to solve the problem.

  Try to boot your Mac in Mode safe. Restart your computer. Hold the SHIFT key when you hear the startup sound. Release the SHIFT key when you see the Apple logo appears. Your Mac starts up in Safe Mode. Safe mode performs a check of your startup disk directory and removes data from the cache. Once your finished Mac commissioning, restart the Mac normally (without hold the SHIFT key) and see if the problem is resolved.

  Make sure your software is up-to-date. The question that you see can be addressed by installing the available updates.

  Check to see where the problem occurs. If a problem arises until you see your desktop, it is less likely that it is related to a setting or a user account. If a problem occurs with a Web site, see if the pages of other websites correctly first load. There could be a problem with the site and not your Mac.

  How to test with another user account

  You can find out if unexpected behavior is related to the user file or a parameter in trying to reproduce the problem to a different user account. This process includes creating a new user account, connect to it and test for the issue.

  Create a test user account

  1. In the Apple menu, choose System Preferences.
  2. Click the users and groups in the System Preferences window.
  3. Click the lock icon and enter an administrator name and password.
  4. Click on the button Add (+) below the list of users.
  5. Choose a type of user in the new pop-up menu.
  6. Give the user a name and first name, account name, and password.
  7. Click OK.
  8. Close the System Preferences window.

  If there are documents from your user account that you want to test with original, place a copy of these items in the shared folder in the users folder. Press the Option key while dragging a file in this folder to create a copy.

  Connect to the test user account

  Log out of your current user account by choosing logout in the Apple menu, and then open a session the new account that you created. If you are prompted to login with your iCloud or Apple ID account when you log in, skip this step.

  Try to reproduce the problem

  Try the same steps that caused the unexpected behavior to appear. For example, if you are unable to print, try printing from this user account. If you were unable to connect to the Internet, try to navigate on a website of this user account.

  If you use specific test settings depends on (for example using a specific e-mail account or an account iCloud) implemented the same test user account. For email and other parameters, you can use the Internet accounts pane in system preferences to set up these types of accounts. If your home folder files are necessary for tests, copy them into the shared folder in the users folder (/ Users/Shared). After you connect as a user test, copy these items to the same location in the test user home folder to test with.

  If a problem occurs in account only one user

  Is using the same steps in a user account test does not cause the same unexpected behavior, most likely you don't need to reinstall applications or OS X.

  • If a problem occurs only in a single application, check the documentation or Web site for instructions on troubleshooting specific preferences or the definition of the application files.
  • If you need help with a problem or a specific alert message, search the Apple support Web site for the text of the alert message you see.

  If a problem occurs in more than one user account

  If the same unexpected behavior occurs in more than one user account on your Mac, try checking for software or hardware problems.

  Once you have finished

  When you are finished testing, disconnect from the test account by choosing logout in the Apple menu. Then, connect to your original user account.

  You can Remove the account to test user created when you are finished. Make sure you're completely finished stable, and you don't need the files or settings you have created or copied there until you delete it.

  Thank you for reaching out to the communities of Apple Support.

  See you soon.

• Messages of blackBerry Smartphones on the ground showing only text Messages

  Hello

  No apparent reason my 'Messages' has begun to show only "SMS" (IE not emails). I tried the help function that directed me to 'options', but I get only options 'General SMS'.

  Help please... !

  Thank you

  Richard

  Hi Richgt

  Welcome to the Forums of the BlackBerry Support

  You want to hide these text Messages from your main message box or your Emails were not filling in your main Inbox?

  Have you tried a battery pull reboot by removing the battery while your unit is powered! Please try it out.

• Rules of the calendar showing the same party as a working day

  Hi all
  
  I use 10.3 OBPM.
  
  I created a so-called holiday "holi_rule" rule and declared a public holiday set by the user. I created a calendar rule and "holi_rule" as a rule of holiday in the civil rule.
  
  When I'm putting the code below
  

  calendarRule = Fuego.Lib.CalendarRule.fetch (calendarName: "India_Calendar_Rule");
  Work date = calendarRule.isWorkDate(time: timeObj.time);
  logMessage ("day of work:"+ work date ");
  Boolean isHoliday = calendarRule.isHoliday(time: timeObj.time);
  logMessage ("holiday is:"+ isHoliday ");
  timeObj.time is an entry I have the purpose of BPM presentation. "

  The two messages appear as true. I don't know why both appear as true. Can someone help me to get the holidays defined by the user as a holiday?
  
  Thanks in advance
  
  Neya-

  Hello

  I hope that the timeObj.time you have defined/recovery of presentation is a holiday that you have defined in the vacation rule.

  Accoring to the rule of holiday is a holiday, but according to the working day that you have defined in the calendar of street is also a day of work.
  So you should make use of the logic of the two tests to discover an effective work day

  If (calendarRule.isWorkDate(time: timeObj.time) == false & calendarRule.isHoliday(time: timeObj.time) == true) {}
  Put your logic here
  }

  Sidonie

• Sorting the columns showing only a line

  Hello
  
  I have a report of sql query that I helped sort on all columns. When I click on the header to sort a column report shows only one line.
  If anyone can help me, I would really appreciate it!
  
  Thank you!

  Once I met a similar problem like the one you describe. I suspect that the problem was related to the data that the report was released.
  I was able to make the problem disappear by disabling "Partial Page Refresh" for the report. Define 'NO' for the attribute "Activate partial Refresh of Page" in the page 'Report attributes' disable PPR for the report.

  CITY

• my iphone 5 c opens more after that I was invited to be updated with itunes. now, the display shows only itunes usb cable and logo. read some tips here, but nothing happened. any help will be much appreciated.

  My iPhone 5 c opens more after that I was invited to be updated with iTunes. now the display shows iTunes logo and the USB cable. I have read and applied some tips here, but nothing happened. Any help will be much appreciated. Thank you.

  https://discussions.Apple.com/message/30014877#30014877http ://

  Read the post from sierrawren . It helped me to fix my phone. Now it works perfectly fine. Hope it can help others too.