Similar Questions

• Satellite 5100-201 problems Windows XP installation (blue screen)

  I have this computer and unfortunately I don't have access to the cd that came with the computer because my cousin has lost. I tried to install Windows XP Professional I bought and during the first installation of Windows XP is about to start I get this blue screen of death message: 0x0000007B (0xF7AFC63C, 0xC0000034, 0x00000000, 0x00000000)

  The computer was working before but but it was extremely slow and the dvd - rom was not recognizable by windows. I tried all the known windows corrections related to the lack of cd-rom drives, but nothing does the job. I can boot from the cd to boot from windows cd. and I even put updated then the bios to 1.90 1.60.

  I have the Toshiba installation CD? There is no other way to install Windows XP Pro? Must I use the Toshiba Recovery CD?

  Hello

  Before starting the installation you need to format the HARD disk or an entire partition. Then you can install your operating system with the original CD of Microsoft Windows XP. After this action, you can install the drivers from Toshiba. All the necessary drivers, you can find the Toshiba site.

  Best regards

• window vista boot blue screen stop: 0x0000007b (0x81e03ba0, 0 x 0000034, 0x00000000, 0x00000000)

  Cannot start PC, using Windows vista, download blue screen error stop: 0x0000007b (0x81e03ba0, 0 x 0000034, 0x00000000, 0x00000000)

  Hello

  1. do you get this error on startup or when working on the computer?

  2. are you aware or any hardware or software changes to the computer?

  Try to start the computer in safe mode and try to make a System Restore.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  System Restore:

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore

  In addition, try and run the steps listed in the link below.

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly:

  http://support.Microsoft.com/kb/958233

• Windows 7 - Crash blue screen - STOP: 0X000000F4

  Hi all

  Windows 7 - Crash blue screen - STOP: 0X000000F4

  Screen shows e blue screen will display the following error code:

  STOP: 0X000000F4 (0XFFFFFA800C4C4B10, 0XFFFFFA800C4C4DF0, 0 X 0000000000000003, 0XFFFFF8000418FE20).
  I tried to restore the mode, the safe & all the option available to start properly.  Given that I have no DVD of windows 7 to re - install windows again.
  My question is as follows:
  -Is - error code says something.
  -A way to re - install windows without CD or DVD or save the image.
  -Also, I can read and access data from the C: & D: drive in cmd in restore mode guest mode.
  Waiting for your suggestions.
  concerning
  Jagdish kone

  Blue_Screen_image_.PDF

  Hi Philippe,.

  Thanks for your reply. I want to reinstall windows on the same SSD. Given that the SSD drive works great as external drive.

  So please could you confirm, how do I reinstall windows again. As I see there are recovery drive comes when I use the SSD as external drive.

  Waiting for your suggestions.

  Concerning

  Jagdish

• My computer windows 7 keeps blue screening

  My computer windows 7 keeps blue screening.

  Here's the info provided (any help would be appreciated!)

  Signature of the problem:

  Problem event name: BlueScreen

  OS version: 6.1.7601.2.1.0.768.3

  Locale ID: 1033

  More information about the problem:

  BCCode: 1000007e

  BCP1: FFFFFFFFC0000005

  BCP2: FFFFF800033689DD

  BCP3: FFFFF88003747818

  BCP4: FFFFF88003747070

  OS version: 6_1_7601

  Service Pack: 1_0

  Product: 768_1

  Files helping to describe the problem:

  C:\Windows\Minidump\021215-28891-01.dmp

  C:\Users\Mario Perez\AppData\Local\Temp\WER-59951-0.sysdata.xml

  Read our privacy statement online:

  http://go.Microsoft.com/fwlink/?LinkId=104288&clcid=0x0409

  If the online privacy statement is not available, please read our offline privacy statement:

  C:\Windows\system32\en-US\erofflps.txt

  Try the following:

  1 perform the clean boot, and then check. See the link form more information:

  http://support.Microsoft.com/kb/929135

  2. If the problem persists, try to perform the SFC scan. Check the link for more information:

  http://support.Microsoft.com/kb/929833

  3. If the problem persists, try to update all device drivers. If no update is available, perform the reinstallation of the drivers: uninstall the drivers, reboot the PC, install the drovers, restart the PC and then check.

  4. However, if the problem persists, look in the dump file that was created (C:\Windows\Minidump\021215-28891-01.dmp), so to find the root cause of the problem.

• Windows 7 clean installation Blue Screen of Death (BSoD) on a loop of reboot

  Aloha everyone,
  I did an install customized windows 7 on a new Western Digital 1 TB sata hard drive, which has been formatted, partitioned, scandisk, and a ntfs c drive was created prior to installation.
  The installation ended safely.  I then install my screen reader, Window-Eyes, requiring a reboot.  After the reboot, I started to install critical updates to Windows.  On my fourth update and restarting, I got the blue screen of death, that of some people call a BSoD.  I rebooted and Windows itself restored to a previous state of good, of my just accept the default choice.  Then the rear computer works, but if I stop, restart I get the blue screen of death (BSod) is back, and the loop begins again, i.e. windows restores good condition that works well, until you stop, but on reboot - BSoD is BACK!
  I removed the automatic update option, I disabled ScanDisk, drivers updated, bluetooth devices, deactivated sideshow, etc., without any positive result.  I called Microsoft for assisstance and the technician acted like this isn't a known issue, but he assured me that he could solve the problem.  He took control of my computer remotely and do not tell me anything except that the computer would check and repair any problem on reboot, and if he did does not resolve the problem, I have to remember.  The computer has rebooted without the BSod, but I stopped to check if the loop went, and it is not!  To restart the BSOd was back.  It is to note that if I put the computer to sleep, I get a clean start, but stop, restart or hibernation, I get the blue screen of death (BSoD)!
  It is a Dell Dimension XPS 420 with a intel Q6600 processer, 3 GB of ddr2 memory, which came with OS Vista Home premium 32-bit.  The Vista system, the last time I got a BSoD has been for more than a year.

  After researching this problem on Google, it appears that there is a problem without a solution.
  I ran "which has crashed, you can get:
  http://www.resplendence.com/downloads

  The following accident report:
  Monday, December 21, 2009 23:23:44 your computer crashed
  This was probably caused by the following module:
  Wininit.exe
  Bug check code: 0xF4 (0x3, 0xFFFFFA800573B060, 0xFFFFFA800573B340, 0xFFFFF80002D91240)
  Error:
  CRITICAL_OBJECT_TERMINATION
  Empty the file: C:\Windows\Minidump\122109-16972-01.dmp
  file path: C:\Windows\system32\wininit.exe
  product:
  Microsoft® Windows® operating system
  company:
  Microsoft Corporation
  Description: Application to Windows startup
  The accident took place in a standard Microsoft module. Your system configuration can
  be incorrect, perhaps the culprit may be another driver on your system which cannot
  be identified at this time.
  Monday, December 21, 2009 20:22:10 crashed your computer
  This was probably caused by the following module:
  Ntoskrnl.exe
  Verification of error code: 0 x 50 (1, 0xFFFFF80002A9300C, 0xFFFFFFFFFFFFFFD0, 0 x 0 x 0)
  Error:
  PAGE_FAULT_IN_NONPAGED_AREA
  Empty the file: C:\Windows\Minidump\122109-33306-01.dmp
  file path: C:\Windows\system32\ntoskrnl.exe
  product:
  Microsoft® Windows® operating system
  company:
  Microsoft Corporation
  Description: NT Kernel System &
  The accident took place in a standard Microsoft module. Your system configuration can
  be incorrect, perhaps the culprit may be another driver on your system which cannot
  be identified at this time.
  Sunday, December 20, 2009 15:28:42 crashed your computer
  This was probably caused by the following module:
  Ntoskrnl.exe
  Verification of error code: 0 x 50 (1, 0xFFFFF80002ADC00C, 0xFFFFFFFFFFFFFFD0, 0 x 0 x 0)
  Error:
  PAGE_FAULT_IN_NONPAGED_AREA
  Empty the file: C:\Windows\Minidump\122009-17565-01.dmp
  file path: C:\Windows\system32\ntoskrnl.exe
  product:
  Microsoft® Windows® operating system
  company:
  Microsoft Corporation
  Description: NT Kernel System &
  The accident took place in a standard Microsoft module. Your system configuration can
  be incorrect, perhaps the culprit may be another driver on your system which cannot
  be identified at this time.
  Thursday, December 17, 2009 12:27:45 AM your computer crashed
  This was probably caused by the following module:
  Ntoskrnl.exe
  Verification of error code: 0 x 50 (1, 0xFFFFF80002A9300C, 0xFFFFFFFFFFFFFFD0, 0 x 0 x 0)
  Error:
  PAGE_FAULT_IN_NONPAGED_AREA
  Empty the file: C:\Windows\Minidump\121609-28111-01.dmp
  file path: C:\Windows\system32\ntoskrnl.exe
  product:
  Microsoft® Windows® operating system
  company:
  Microsoft Corporation
  Description: NT Kernel System &
  The accident took place in a standard Microsoft module. Your system configuration can
  be incorrect, perhaps the culprit may be another driver on your system which cannot
  be identified at this time.
  Monday, December 14, 2009 20:59:21 crashed your computer
  This was probably caused by the following module:
  Wininit.exe
  Bug check code: 0xF4 (0x3, 0xFFFFFA80059A3060, 0xFFFFFA80059A3340, 0xFFFFF80002DC4240)
  Error:
  CRITICAL_OBJECT_TERMINATION
  Empty the file: C:\Windows\Minidump\121409-25506-01.dmp
  file path: C:\Windows\system32\wininit.exe
  product:
  Microsoft® Windows® operating system
  company:
  Microsoft Corporation
  Description: Application to Windows startup
  The accident took place in a standard Microsoft module. Your system configuration can
  be incorrect, perhaps the culprit may be another driver on your system which cannot
  be identified at this time.
  Sunday, December 13, 2009 02:17:55 your computer crashed
  This was probably caused by the following module:
  Wininit.exe
  Bug check code: 0xF4 (0x3, 0xFFFFFA80058A4060, 0xFFFFFA80058A4340, 0xFFFFF80002D8A240)
  Error:
  CRITICAL_OBJECT_TERMINATION
  Empty the file: C:\Windows\Minidump\121209-24648-01.dmp
  file path: C:\Windows\system32\wininit.exe
  product:
  Microsoft® Windows® operating system
  company:
  Microsoft Corporation
  Description: Application to Windows startup
  The accident took place in a standard Microsoft module. Your system configuration can
  be incorrect, perhaps the culprit may be another driver on your system which cannot
  be identified at this time.
  Conclusion
  6 dumps were found and analysed. Note that it is not always possible to
  assert with certainty whether a reported driver is really responsible for crashing
  your system or that the cause is in another module. However, it is suggested
  looking for updates for the products that these drivers belong to and regularly
  Visit the Windows Update or activate the automatic updates for Windows. In the case of a piece of
  defective material is in trouble, a Google search on the bug control
  Errors, as well as the name of the model and brand of your computer can help you investigate
  This further.
  end of the crash report.
  A side comment:
  Them are 56 reported problems, and none of them have solutions. If I go through each problem report and check for solutions, about 80% of the times I ask myself to send to Microsoft for more information about the problem and I click on send, but I always get the following:
  [Window title]
  Incident reports

  [Main instruction]
  Problem connecting to the Windows error reporting service

  [Content]
  Some of the reports can not be uploaded to the Windows error reporting service. Please try again later.

  [Close] »
  I tried several times with the same result, that is, the details of the problem which has need of Microsoft is not be received.  To this end, the problem will not be found.
  Thanks much for any help.
  Manny
  P.S. I'll never upgrade a Windows operating system.  My recommendation for anyone who is planning to upgrade to Windows 7 is to try first on a dual boot using the free download.  If it works for you, consider yourself lucky and buy the upgrade.  If it does not, then remove Windows 7 and stay with your old system.

  Please check your RAM for errors (use memtest86 + to test). "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• Installation of Powershell 2 on Windows Vista causes Blue Screen of Death

  I tried to install Powershell 2 on my Windows Vista Home Premium (with SP2) machine. I use the Windows6 package. 0-KB968930-x 86.msu. However, in the middle of the installation, I get a blue screen of death, and the computer restarts.

  I don't know if it is a help, but the problem report displayed when the machine came back to the top is as follows:

  Signature of the problem:

  Problem event name: BlueScreen

  The system version: 6.0.6002.2.2.0.768.3

  Locale ID: 2057

  More information about the problem:

  BCCode: 1000008e

  BCP1: C0000005

  BCP2: 00000000

  BCP3: 8FB3DB9C

  BCP4: 00000000

  OS version: 6_0_6002

  Service Pack: 2_0

  Product: 768_1

  Files helping to describe the problem:

  C:\Windows\Minidump\Mini073110-01.dmp

  C:\Users\Martin Lee\AppData\Local\Temp\WER-142803-0.sysdata.xml

  C:\Users\Martin Lee\AppData\Local\Temp\WER25F6.tmp.version.txt

  Hello CodeMunger,

  You can post on the Forum of Microsoft Powershell. Click here for a link to the forums.
  They may be better able to help with your questions.

  Sincerely,

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Gateway Windows 7: stop blue screen during the installation of Windows 7: 0 x 00000024

  OK, I've had so many problems with this computer and I would love to have the support of the community.
  I have a Gateway desktop that is labeled for Windows vista. I had already installed Windows but a virus brought me to uninstall. I don't have the disc, but I have a flash drive with windows 7 on it. So I have my computer to run the player flash start run the windows setup program. I get to the part after the selection of my hard drive. It comes down to 50-60% full, and then it stops at a blue screen with stop code error 0 x 00000024 (0x0000000000190FB 0XFFFFF88003B8C269 0XFFFFF88003BAC0 0XFFFFF8000D292FOD) I have searched and searched for a solution but none to my knowledge, I am only 16 and very bad so I can not affored a new computer, or a repair of $75. Please when replying to this is so simple and stright forward. Thanks a lot for taking time outta your day to help me.

  Pearen

  These were related to the Extensible Atheros athr.sys wireless device driver. I would re - install newer and updated the drivers listed below and updated to update to Service Pack 1
  

  Run (SURT) system update readiness tool and then update to Service Pack 1

  32 bit
  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=3132
  64 bit
  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=20858

  Now updated for Service Pack 1
  http://Windows.Microsoft.com/installwindows7sp1

  Learn how to install Windows 7 Service Pack 1 (SP1) http://windows.microsoft.com/en-US/windows7/learn-how-to-install-windows-7-service-pack-1-sp1
  
  Additional resources:
  http://Windows.Microsoft.com/en-us/Windows7/uninstall-SP1
  http://Windows.Microsoft.com/troubleshootwindows7sp1

  Older drivers who need to update your driver of athr.sys which is 3 years old inclusive
  SCDEmu.SYS Mon Jul 7 03:40:49 2008 (4871-881)
  PowerISO Virtual Drive driver
  http://www.carrona.org/drivers/driver.php?id=SCDEmu.sys
   
  VSTCNXT3. SYS Wed 15 Oct 20:29:13 2008 (48F68AD9)
  Conexant SoftK56 Modem driver
  http://www.carrona.org/drivers/driver.php?id=VSTCNXT3.sys
   
  VSTAZL3. SYS Wed 15 Oct 20:30:03 2008 (48F68B0B)
  Conexant SoftK56 modem
  http://www.carrona.org/drivers/driver.php?id=VSTAZL3.sys
   
  VSTDPV3. SYS Wed 15 Oct 20:32:04 2008 (48F68B84)
  Conexant SoftK56 Modem driver
  http://www.carrona.org/drivers/driver.php?id=VSTDPV3.sys
   
  Rt86win7.sys Thu Feb 26 04:04:22 2009 (49A65B16)
  Realtek NETWORK card
  http://www.carrona.org/drivers/driver.php?id=Rt86win7.sys
   
  amdxata.sys Tue May 19 13:57:35 2009 (4A12F30F)
  AMD - usually from the Windows 7 DVD storage controller driver
  http://www.carrona.org/drivers/driver.php?id=amdxata.sys
   
  ATHR.sys kills Jun 9 14:04:52 2009 (4A2EA444)
  Atheros Extensible Wireless LAN driver for network card CB42/CB43/MB42/MB43-D-Link AirPlus DWL-G520 Wireless PCI Adapter(rev.) (B) discontinued 2008
  http://www.carrona.org/drivers/driver.php?id=ATHR.sys

  Run (SURT) system update readiness tool and then update to Service Pack 1

  32 bit
  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=3132
  64 bit
  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=20858

  Now updated for Service Pack 1

  
  http://Windows.Microsoft.com/installwindows7sp1

  Learn how to install Windows 7 Service Pack 1 (SP1) http://windows.microsoft.com/en-US/windows7/learn-how-to-install-windows-7-service-pack-1-sp1
  
  Additional resources:
  http://Windows.Microsoft.com/en-us/Windows7/uninstall-SP1
  http://Windows.Microsoft.com/troubleshootwindows7sp1

  BugCheck D1, {30, 2, 0, 902658a 5}
  Probably caused by: athr.sys (athr + 428a 5)
  ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨``
  BugCheck D1, {30, 2, 0, 918618a 5}
  Probably caused by: athr.sys (athr + 428a 5)
  ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨``
  BugCheck D1, {30, 2, 0, 94c448a5}
  Probably caused by: athr.sys (athr + 428a 5)

• XP installation blue screens

  I have a R100 and also a P2000 and uses an external cd-rom Toshiba F - TO - CD - 24 L with adapter PCMCIA.

  During the installation of XP blue screens exactly the same installation point on two laptops. It is at the stage of setting up pre - gui that is right before you accept the EULA.

  I tried changing the settings of Cardbus, using a different external (Freecom) CD and can't get out.

  I can use the restore cd but don't want to because I need to prepare an image of the company.

  I called the technical support of Tosh and they claim, there is no problem and that they do not support anything other than the restore cd and not ready to discuss it.

  Is there anything else I can try - a toshiba new CD-ROMs may be? Why do the work of the cd of restoration but not my xp cd?

  Hello

  Toshiba Recovery CD is composed not driver for external Toshiba CD and the Microsoft Windows XP Home edition CD. Before starting the installation of the device external need the driver to work properly.

  Please visit this site
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/FAQ.jsp?service=EU&from=faq_selection&CFID=CD-ROM+and+DVD&FID=tro0000001721

  Good bye

• The installation blue screen: STOP: 0x0000007E (0xC0000005, OxF748E0BF, OxF78DA208, OxF789D9F08,

  Original title: cannot format the new hard drive because when I boot the system disk it stops with several STOP error.

  I am trying to solve problems with desktop Dell XPS 420 of my daughter. He started with the message 'bootmgr' trying to get the windows computer.  She ordered a new hard drive and when it was physically connected, I put put in place the disc in the computer to boot from to install windows XP, but it always comes to the blue screen with the following error: (I'm not an expert on computers so that any help must be in a very basic language).
  STOP: 0x0000007E (0xC0000005, OxF748E0BF, OxF78DA208, OxF789D9F08,
  PCI.sys-address F748E0BF base at F7487000
  DateStamp 3b7d855c

  I retried the boot and got the same error.  I check the forums online and they suggest that to go in safe mode.  I can't go in safe mode - do not have an operating system installed yet.  Some have said to change organic caching and shadowing.  I don't know how to do and I can't get into safe mode.  I don't know what to do.  Of course, the warranty was out - 2008 computer.

  Can anyone help or point me in the right direction? My funds are limited to pay Dell for the solution.  Thank you.

  MDT? Does not look good. See:

  http://www.computing.NET/answers/hardware/MDT-hard-drive/23869.html

  I still don't understand why you think that you need a new hard drive. There is nothing prevents you to install own XP on the old disk.

  If you can't find the right drivers (I don't know where to find them), maybe you can get in Dell's BIOS and change the hard drive controller affecting IDE or legacy or something like that. Then the new disc would work.

  Or you can simply put the back of an old man. You can either try to repair your installation of Windows with our help or opt to perform a clean installation.

• Windows Vista, several blue screen errors

  Original title: BSOD

  Good afternoon

  I have the BSOD. Here they are in chronological order:

  1 IRQL_NOT_LESS_OR_EQUAL 0X0000000A (0X0000001D, 0XFFFFFFC2, 0X82424EF8, 0X00000001)
  2 0X000000c4 (0x000000A0, 0X96AEEA58, 0x995FCEE0, 0x0D99EEE4)
  3 0X000000c4 (0x000000A0, 0X968F0DF0, 0x99406EE0, 0x053F1D0A)
  4 0X000000c4 (0x000000A0, 0X9A651638, 0x993C4EE0, 0x10AB65F8)

  Additional information:

  Windows Vista Service Pack 2

  DualCore Intel Core 2 Duo E8400 3000 MHz (9 x 333)

  Gigabyte GA-G33M-DS2R (2 PCI, 1 PCI-E x 4, 1 PCI-E x 16, 4 DDR2 DIMM, Audio, Video, Gigabit LAN)

  DDR2-800 DDR2 SDRAM

  BIOS: Award BIOS v6.00PG Modular

  Could you help me... don't really know what to do...

  Hello

  Check this thread for more information using BlueScreenView, MyEventViewer and other methods
  to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

  http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

  We can analyze the minidumps if make you it available to the SkyDrive or another file
  sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
  for the office or in the Documents folder and download them from there.

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive to upload collected files
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  ----------------------------------------------------------

  BCCode: 0a 0x0000000A

  Drivers could be at fault, however the problems of disk or security/antivirus/antispyware products are
  just as likely to be the root cause that they can force a driver to corrupt or go out of bounds.
  The video driver or something affecting it would be questionable.

  At the end of this message, I'll post a bluescreen generic and in the next convenience store
  How do to update the drivers and BIOS but also to check memory message.

  -----------------------------------

  BCCode: 0a 0x0000000A

  Cause

  This bug check is issued if the memory paged (or invalid) is accessible when the IRQL is too high.

  The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.

  If you encounter a bug 0xA control during the upgrade to a later version of Windows, this error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version.

  Solve the problem

  If a kernel debugger is available, get a stack trace.

  To resolve an error caused by the faulty device driver or service system, BIOS

  1. Restart your computer.
  2. Press F8 to character-based menu that displays the choice of operating system.
  3. In the WindowsAdvanced Options menu, select last known good Configuration . This option is most effective when a pilot or a service is added at a time.

  To resolve an error caused by an incompatible device driver, system service, virus scanner, or backup tool

  1. Check the system log in Event Viewer for error messages that may identify the device or driver that caused the error.
  2. Try disabling the cache in memory of the BIOS.
  3. Run the diagnostics of equipment provided by the manufacturer of the system, in particular the scanner memory. For more information about these procedures, see the manual of your computer.
  4. Make sure that the latest Service Pack is installed.
  5. If your system has cards (SCSI) small computer system interface, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination.
  6. For devices (IDE) peripheral electronic integrated, set the built-in as only primary IDE port. Also, check each IDE device to the right setting master/slave/stand alone. Try to remove all IDE devices except for the hard drives.

  If the message appears during installation of Windows, make sure that the computer and installed devices are listed in the list of the products tested Microsoft Windows market.

  Comments

  Before upgrading to a new version of Windows, remove all third-party device drivers and system services and disable any antivirus. Contact software manufacturers for updates of these third-party tools.

  BCCode: 0a 0x0000000A<-- read="" this="">
  * 1025.html http://www.faultwire.com/solutions-fatal_error/IRQL-not-less-or-Equal-0x0000000A-

  ==================================================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------
  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do without if needed fail or the Vista DVD or recovery command prompt mode
  Options if your system was installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Windows 7 Pro Blue screen

  This is the problem such as specified after the recovery, any help is appreciated.

  BCCode: 7f

  BCP1: 0000000000000008

  BCP2: 0000000080050033

  BCP3: 00000000000006F8

  BCP4: FFFFF80002A54D28

  OS version: 6_1_7600

  Service Pack: 0_0

  Product: 256_1

  Hello

  You have ZoneAlarm or any 3rd party firewall installed? If so, this could be the cause.
  Other antivirus/security programs could be at least partially responsible.

  This fix "could" apply however do not use if you are quite safe.

  Two drivers of platform using WFP (Windows Filtering) causes a computer crash when the
  computer running Windows Vista, Windows 7 or Windows Server 2008
  http://support.Microsoft.com/kb/979278

  Also check these:

  Stop error message when you run an application that transfers data using the UDP protocol
  in Windows Server 2008 R2 or in Windows 7: "STOP 0x0000007F"
  http://support.Microsoft.com/kb/981180/

  The General causes of errors "STOP 0x0000007F" (applies to Vista and Windows 7 as well)
  http://support.Microsoft.com/kb/137539

  ===========================================================

  For the methods of troubleshooting blue screen using BlueScreenView and MyEventViewer see my answers
  If this thread - top 3 RESPONSES (+ 1 other).

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/c675b7b8-795f-474d-a1c4-6b77b3fcd990

  ----------------------------------------------------

  It's my usual BlueScreen convenience store.

  References to Vista also apply to Windows 7.

  BCCode: 0x0000007f with the parameter 00000008 7f usually means a hardware problem.

  Have you added a hardware or drivers updated recently? Check Control Panel - Windows
  Updates to see if all drivers have been updated it just before what is going on has begun.

  For 7f - this could be a problem of material such as uncomfortable cards or memory, while there are
  other causes. Power electric low could also lead to this. Use the troubleshooters above and below
  and when you get to the drivers and memory sections refer to my next message below and then
  go back troubleshooting if necessary. (Can't really do a lot for the hardware on your laptop).

  If a PC remove ALL power. Opening the case, remove and reinstall all memory cards and ALL
  cable (try not just to close) on both ends if they are accessible and on the device ends if not
  (remove the cables and the resettlement of help them to eliminate minor corrosion).

  Notice the 08 (double fault) as 1st parameter means there is likely to be two causes. Do not forget to
  Update your drivers manually as using discoveries only updates Windows certified drivers and Microsoft
  and device manufacturers are far behind in this process. NETWORK, WiFi, BIOS and video/display card update
  and other great pilots

  If a laptop or a PC, you will need to take a shop (not BestBuy or other BigBox stores) or your
  Support of the machine system.

  ----------------------------------------------------------------------

  BCCode: 7F 0x0000007F which is the same as 0x1000007F

  UNEXPECTED_KERNEL_MODE_TRAP bug control has a value of 0x0000007F. This bug check indicates that the Intel CPU generated a trap and the kernel could not catch this trap.

  This trap might be a bound trap (a trap the kernel is not allowed to capture) or adouble foul(an error occurred during the processing of an earlier fault, which always results in a failure of the system).

  Parameters

  The first parameter that is displayed on the blue screen indicates the number of trap.

  The most common trap codes are the following:

  • 0x00000000 or division by zero error, indicates that a DIV instruction is executed and the divisor is zero. Memory corruption, other hardware problems or software failures can cause this error.
  • 0 x 00000004, or overflow, occurs when the processor executes a call to an interrupt handler when the overflow (OF) is flag set.
  • 0x00000005, or limits check fault, indicates that the processor, then executing a BOUND instruction, determines that the operand exceeds the specified limits. A BOUND instruction ensures that a signed array index is within a certain range.
  • 0 x 00000006 or Opcode not valid, indicates that the processor attempts to execute an invalid instruction. This error occurs generally when the instruction pointer is corrupted and point to the wrong address. The most common cause of this error is hardware memory corruption.
  • 0x00000008 or Double fault, indicates that an exception occurs during a call to the previous exception handler. In general, two exceptions are handled in series. However, there are several exceptions that cannot be handled serially, and in this case, the processor signals a double fault. There are two common causes of a double fault

  
  CAUSE

  0x7F bug check occurs after the installation of a faulty or incompatible hardware (including memory) or if installed hardware fails.

  A double fault can occur when the kernel stack overflows. This overflow occurs if multiple drivers are attached to the same battery. For example, if two file system filter drivers are associated to the same stack and then again the recursively of file system, the capacity of the battery.

  Solve the problem

  Troubleshooting: If you have recently added the material to the computer, remove to see if the error recurs. If the hardware failure existing, remove or replace the faulty component. Run the diagnostics of material that does not have the system manufacturer supplies to determine which hardware component.

  The scanner memory is particularly important. Faulty or incompatible memory can cause this bug check. For more information on these procedures, see the manual of your computer. Check that all the cards in the computer are well calibrated. Use an ink eraser or electrical contact treatment, available in electronic supply stores, to ensure the adapter card contacts are clean.

  If the error appears on a newly installed system, check the availability of updates for BIOS, SCSI, or card network controller. These updates are generally available on the Web site or the hardware manufacturer BBS.

  Confirm that all hard drives, hard disk controllers and SCSI adapters are listed in the list of the products tested Microsoft Windows market.

  If the error occurred after the installation of a new or updated device driver, you should remove or replace the driver. If, in this circumstance, the error occurs during the startup sequence and the system partition is formatted with NTFS, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console in order to access the file.

  Also to restart your computer and press F8 to character-based menu that displays the choice of operating system. In the menuof Advanced Options , select thelast known good Configuration option. This option is most effective when you add a single driver or service at a time.

  Overclocking (setting of the CPU to run at a speed higher than the nominal specification) can cause this error. If you have overclocked to the computer that is experiencing the error, return the CPU to default clock speed setting.

  Check the system log in Event Viewer for additional error messages that might help identify the device or driver that generated the error. You can also disable caching memory BIOS to try to resolve the problem.

  If you have encountered this error during the upgrade to a new version of the Windows operating system, the error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version. If possible, remove all third-party device drivers and system services and disable all antivirus before upgrade you. Contact the software manufacturer for updates of these tools. Also, make sure that you have installed the latest Windows Service Pack.

  Finally, if all of the steps above do not resolve the error, take the system motherboard to a repair for the diagnostic facility. A crack, a scratched trace, or a defective component on the motherboard can also cause this error.

  BCCode: 7F 0x0000007F which is the same as 0x1000007F<-- read="">
  * 1304.html http://www.faultwire.com/solutions-fatal_error/Run-a-System-diagnostic-Utility-supplied-by-your-0x1000007F-

  ==========================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers to 7 (update drivers manually using the methods above is preferred
  to make sure that the latest drivers from the manufacturer of system and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  Hope this helps. |

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Windows 7 PC Blue Screen: STOP 0x000000F4

  Three weeks, my computer began to experience regular blue screens for no discernible reason. My first instinct was to update all my drivers and make sure that I had all the latest updates, I also ran several diagnostics; memory and hardware checks, analyses the virus, it came up saying everything's fine. I run a custom Setup, so I tried unplugging different disks without success, which leads me to believe, there is a problem with the boot drive, but, as I said, all the checks I ran on it come back saying otherwise.

  I tried to download the Windows SDK to run several tests, but there will be nothing more than the computer. I tried to run the system restore several times and always, he fails to finish, then when I come back, regardless of the system image, I tried to restore will be gone.

  I tried to swap around cables on all players with brand new ones and that does not work so I'm kinda an impasse, any suggestions would be helpful.
  Here is some information on the blue screen, the last times, he only has not dumped physical memory:
  A problem has been detected and windows has shut down to prevent damage to your computer.
  A process or thread crucial to system operation has unexpectedly left or came to an end.
  If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:
  Check to make sure any new hardware or software is installed correctly. If it is a new installation, ask your hardware manufacturer or software, the windows updates, you might need.
  If problems continue, disable or remove any newly installed hardware or software. Disable the BIOS memory options such as implementing caching or shading. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode.
  Technical information:
  STOP: 0X000000F4 (0XFFFFFA800704AB30, 0XFFFFFA800704AE10, 0 X 00000000000000003, 0XFFFFF800035CE350)
  Data collection for the crashdump...
  Initializing disk for crash dump...
  
  
  System log:
  http://sdrv.Ms/10RoTfi
  Application log:
  http://sdrv.Ms/10RoYPX
  Update of information system:
  http://sdrv.Ms/10Rp76b

  What is your computer brand and model? If not a branded computer, what is your motherboard brand and model?

  You may be affected by the problem described in this link:
  http://en.kioskea.NET/FAQ/29514-crucial-M4-how-to-remove-the-5200-hours-bug

  http://www.crucial.com/support/index.aspx

  To find out what firmware revision your SSD is running, follow these steps:.
  1. click on the start menu
  2. open the control panel > system > hardware
  3. Select Device Manager
  4. expand disk drives
  5. right click on the drive and select Properties
  6. Select the Details tab, and then select "Lds material" in the dropdown menu drop-down. The firmware version will appear on the far right.
  Source: http://forums.crucial.com/t5/Solid-State-Drives-SSD-Knowledge/How-to-Find-Your-Firmware-Revision-Windows/ta-p/114208

  The verification code bug for BSOD errors you encounter is 0xF4, so this may be the cause of your problem.

  Your file system information-[peripheral problem]

  Device PNP Device ID error Code USB Universal Serial Bus () controller PCI\VEN_1B21 & DEV_1042 & SUBSYS_84881043 & REV_00\4 & 16B16BD2 & 0 & 00E7 that the drivers for this device are not installed.

  You need drivers Asmedia. When you say your computer brand and model, I can be able to provide more help.

• Satellite M30x - bootsequence Windows XP with blue screen

  I have the following problem: I have 2 different Satellite M Series notebooks of performance!

  The problem, that I wonder happens 100% of the tests, but after turning on the computer laptop and after the bootsequence - at the present time, that the windows XP logo appears - the system halts with a blue screen. Turn to restart and falls into the next blue screen.

  The only thing I discovered is that XP regularly also begins long switch WLAN hardware is turned OFF as soon as I turn this switch with Windows, the blue screen occurs immediately and the system runs out of oil.

  is that what is anyone able to help? -new review of pilots or any other solution to the problem would be appreciated!

  Hansjoerg

  Hey,.

  Congratulations, you have already found the problem! :)

  From my own experience, I can tell you that the same thing happened to a friend of mine. So he replaced the WLAN card with a new one and the problem has been resolved! Windows starts with WLAN turn on () correctly!

  What WLAN card is installed on your laptop?
  In Satellite M30x of my friend a WLAN Wireless Intel 2200 card has been installed. He bought a new one for little money on eBay and replaced it yourself because it s not very delicate.

  So take a look on eBay or other places. You can also ask a maintainer approved assistance if you are not familiar with the disassembly of the laptop.

• Windows crash - big blue screen with a sad smily comes then it reboots sometimes

  Hi all, I bought an acer Aspire V3 - 772G with 8 windows pre installed. the thing is while in the middle of something, a blue screen appears just saying that your pc just came across a problem, gives error names such as IRQ_NOT_LESS_OR_EQUAL, look for this error on the internet later... This has been driving nuts me lately. I thought that the problem was with windows 8, so I've upgraded to windows 8.1 but still sometimes. How the hell can I solve this problem? all of the suggestions. What exactly is the problem? any help is appreciated in advance.

  After spending about $ 1,000 on the computer I wasn't expecting this kind of errors.

  Thank you.

  Yes, too common.

  as suggestion, if you are still under warranty, call Acer customer service, probably isn't a hardware issue.