Windows 7 installs due to the error of the BIOS

Similar Questions

• Windows XP installation hangs when the BIOS is set to AHCI

  I have Windows 7 on my computer. It has a motherboard Asus P8Z77 - V LX with the AHCI BIOS.

  Now, I would like to install Windows XP to a dual boot set up so that my son can continue to play some of their old games XP.

  When I tried to install XP, I got the BSOD during the first phase of the installation process.

  Internet research, I discovered that Windows needs a controller AHCI driver and that I could use F6 to install the appropriate driver to a diskette during installation or wake the driver in a Windows installation CD using a program called nLite. I chose the latter because there are no floppy drive on the computer. I chose the version XP 32 bit Intel (R) series 7/216 Chipset Family SATA AHCI Controller to wake.

  I used my newly created installation disk and the initial phase of installation is fine, but after the first reboot, just like the Windows XP GUI interface appeared, the system crashed, rebooted and crashed again.

  The only way I could get XP install was to change the BIOS to IDE, then it installed fine. But Windows 7 does not load unless I have change the AHCI BIOS so that's what I've done so far.

  Suggestions as to how I can either get XP to install in AHCI mode or change it to AHCI mode, once it has been installed in IDE mode?

  OK, my apologies, it seems I have didn't read entirely your answer. I have BSOD stop 7B have treated several times and has been guilty of inaccurate "quick read".

  However, I gave you a possibility through response to your last paragraph...

  install the drivers for XP AHCI as it is started in IDE mode, and then change the AHCI BIOS

  .. have you tried this? What were the results?

  After thinking a bit about this possibility, it may be a good idea to restart in IDE mode after installing the AHCI driver before then stopping and switching to AHCI mode.

  As far as I know there are only two possibilities for the installation of the AHCI driver when installing XP. You dismissed one of them (Setup F6 disk) and you say that the other does not have a bootable system. Maybe you could try to "slipstreaming" once again, in which case the process did not work properly. Where did you get the drivers from making the wake? Was it the same place as the link I posted above? Absence of "slipstreaming" or the purchase of a (cheap) floppy drive, my only suggestion is that I repeated above.

  Finally, can you confirm that it is stop 7B that you get? If not what stop do you receive?

  Tricky

• Cannot update Windows Vista kb971468 due to the error message 800B0100__

  Cannot update Windows Vista kb971468 due to the error 800b0100 of message

  Error code when you try to use Windows Update or Microsoft Update to install updates: "0x800B0001":
  http://support.Microsoft.com/kb/958045

  Vista SP1 or SP2 installed?

  What application or antivirus security suite is installed and your current subscription?  What anti-spyware (other than Defender) applications?  What third-party firewall (if applicable)?

  A (another) Norton or McAfee application has already been installed on the computer (for example, a free trial version which is preinstalled when you bought it)?

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• When I run mbsa 2.2 I get = firewall tests Windows may be due to an error. (0x8004100e)? What should I do to remove this message?

  When I run mbsa 2.2 I get = firewall tests Windows may be due to an error. (0x8004100e)? What should I do to remove this message? a few hours back this problem wasn't there, but now I'm stuck! Help?

  Hello

  Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the public on the TechNet site. Please post your question in the below link: http://social.technet.microsoft.com/Forums/en-US/MBSA/threads

• I can not write the new message of Windows Live Essentials due to the demand of Silverlight.configuration.exe freeze my computer. How to replace this command?

  Silverlight.config.exe. appears again msg then causes a gel

  I can not write the new message of Windows Live Essentials due to the demand of Silverlight.configuration.exe freeze my computer.  How to replace this command?

  Hi JaphetMorales.

  (1) did you change on your computer before this problem?

  (2) what operating system is installed on your computer?

  What version of the operating system Windows am I running?

  http://Windows.Microsoft.com/en-us/Windows7/help/which-version-of-the-Windows-operating-system-am-i-running

  You can uninstall and reinstall Silverlight and then check.

  http://www.Microsoft.com/getSilverlight/get-started/install/uninstall-win.aspx

  See also:

  http://support.Microsoft.com/kb/977116

• Windows 8 installation fails with the error "the product key entered don't match any available to install windows images.

  I have a Sony Vaio SVE1113M1EB provided with pre-installed Windows 8. Yesterday, my laptop won't start and recovery tools did not work. Then I deleted the partitions in stock and tried to install Windows 8 on DVD. He said: "the product key entered is not one of the images available for installation windows." I wrote my product key. How to install Windows 8?

  Original title: Installation of Windows 8

  Hi Qadir,

  The issue could be due to the supplied product key does not match the press which is used to install Windows. The product key that is provided can be a file without assistance, in a. EI. CFG file, in the PID.txt file or in the BIOS firmware. Windows OEM 8 machines ship with the product key in the firmware, and if this product key does not match the press, then you will see the above error message.

  I suggest you to change the product key to the correct for the media you are trying to install. If the system has a product key in the motherboard (o. a. 3.0 [Activation OEM] provides an OEM product key in the firmware), you use an Unattend file, file (EI.cfg) edition Configuration or the product ID file (PID.txt).

  You can check the link:

  «Windows 8 or Windows Server 2012 installation may fail with the error message: the product key entered does not match any of the images available for installation Windows.» "Enter a different product key"

  http://support.Microsoft.com/kb/2796988/en-us

  I hope this helps. If you have any other questions, we will be happy to help you.

• has received a notice to upgrade USB key - how? In addition, advice the installation due to the error #5 help is understand__

  has received a notice to upgrade USB key how?    also notice that on the upgrade installation is not complete due to the error #5 why?

  Please need help do not understand

  http://kb2.Adobe.com/CPS/141/tn_14157.html

  Uninstall Flash by using the uninstall program Flash Adobe link above.

  Flash is sometimes corrupted.

  http://get.Adobe.com/flashplayer/?promoid=BUIGP

  Reinstall Flash, after 1st unchecking / uncheck the toolbar Google download option there.

  See you soon.

  Mick Murphy - Microsoft partner

• Windows 7 installation hangs on the compatibility check

  I am trying to install Win7 (Home premium) update my Vista, but every time the installation starts a compatibility check and goes no further. I let go more than an hour with no progress.  I have run the Upgrade Advisor and it's compatible. So, how do the installation to ignore or perform this check?

  Troubleshooting tips to solve common problems when Windows 7 won't install - try everything you did not yet.
   
  1. start Windows Upgrade Advisor to see if there are known issues that might affect the installation and correct them.
  http://Windows.Microsoft.com/en-us/Windows/downloads/Upgrade-Advisor
   
  2 disable any security software: anti-virus, firewall etc. Don't forget to activate the Afterwords.
  3 make sure that your computer has the BIOS and latest drivers. Update of the BIOS can be risky, don't do that if nothing else works.
  4. disconnect all external devices except the keyboard and mouse before installing.
  5. If using a video card and the computer has integrated video use and remove the video card.
  6 unplug the computer from the internet, if you have wireless disable.
  7. RAM (memory) - reduce the amount of RAM. 1 GB if 32-bit installation, 2 GB for 64-bit, then replace RAM if the upgrade was successful. If you added new RAM make sure it is also compatible.
  8. If you have several hard drives remove all except the one that you install Windows 7, and then replace it after Windows 7 is installed.
  9. If you have downloaded Windows 7 and it burned a DVD test burn again at the slowest speed possible. It is also possible the download may have errors, you can try to download it again.
  10. If you click 'Upgrade' to start the installation make sure that you take a supported upgrade path. You can't make a room upgrade: A) XP to Windows 7, B) changing bit type ex: 32 to 64-bit C) change the languages, D) decommissioning editions ex: Vista of the month last 7 Pro, or E) Vista Home Pro 7.
   
  11. check your RAM (memory) to find errors. Can take a long time, don't make that if nothing else has worked.
  (A) Insert the Windows 7 DVD and restart the computer.
  (B) start from the Windows 7 DVD.
  (C) select your language, and then click Next.
  (D) click on "repair your computer" then select the operating system to fix it.
  (E) click on the link of the Memory Diagnostics in the system recovery menu.
  (F) the computer will restart and your memory is checked for errors.
   
  12 turn off startup programs:
  (A) click Start, type MSCONFIG in the search box and press ENTER.
  OK the authorization of user account control and password if necessary
  If you are using XP: click Start, run, and type: MSCONFIG and click OK.
  (B) on the general tab, click Selective startup.
  (C) just below the selective startup, clear the checkbox "Load Startup items".
  (D) click the Services tab, check "Hide all Microsoft Services", and then click Disable all.
  (E) click OK, and then restart the computer.
  (F) try the upgrade again.
   
  (NOTE: If the upgrade fails and you continue to use your rear security software, then also go back into MSCONFIG and under the general Tower XP/Vista tab, click "Normal startup", and then click OK to exit.)
   
   
  Questions about installing Windows 7?
  FAQ - Frequently Asked Questions from Installation Windows 7 & responses

• Windows 7 installation hangs at the end of the installation on Optiplex 380

  Trying to do a fresh install of Windows 7 pro on an Optiplex 380. Installation on a new sata WD 500 hd crashes.

  The pc was purchased from Dell and came with installed Win XP and Win 7 DVD. The only change from the original configuration was to install a Radeon HD 4650 graphics card.

  Although it does not have some puff at the back usb ports, it is otherwise works perfectly well in XP. Latest BIOS uopdated. Anything else that the keyboard usb, usb mouse, video cable dvi and cable network.

  A web search shows a wild range of suggestions - remove this, disable, enable AHCI in the bios

  Thanks for the links.

  Watching the DVD I was using and he was embarrassed to see that he was 4 years old well in its sealed packaging. Of course no SP1 etc. Before trying to update the Sata drivers separately, decided to download a recent iso - http://www.heidoc.net/joomla/technology-science/microsoft/14-windows-7-direct-download-links - try and install it. Went like a charm with no problems whatsoever.

• Windows 7 installation fails during the expansion of the files (27%)

  I am trying to install Windows 7 Home Premium, substituting a clean installation of Windows XP SP3.  Whenever the procedure reached 27% during the "expanding files" step, restarts and crashes, then with "Starting Windows" is displayed.

  The hardware is Pentium IV 2.8 GHz, 2.5 GB RAM, nVidia GS7800 with DirectX 9 .0c

  Frustrating, or what?

  Hard drive controller probably needs you better drivers. Go to the site of the manufacturer of the system for controller Win 7 drivers.

  Messages rating helps other users

  Mark L. Ferguson MS - MVP

• Satellite A100 - BIOS and Windows does not start after the BIOS update

  Hello, I extend my Satellite A100 laptop BIOS.

  After update, I can't start my laptop and the BIOS will not start.

  You see the Toshiba logo?

  Was there a power failure when you updated the BIOS?

  Try to remove the battery and the adapter and leave for a few hours. You can also try reinstalling the RAM.

  If this does not help, you will need to send it to a Service Center for repair.

• can not sync music to any memory card in Windows Media Player due to the error Windows encountered a problem when synchronizing the file to the device.

  Original title: can not sync music to any Windows Media Player memory card

  This has not happened before, but now, whenever I want to sync music to any memory card, it does not work. It makes the whole process, and it did as it syncs, but at the end of that music just does not appear in the memory card. If I go to the status of the synchronization, all songs appear with a RED x next and it says that Windows has encountered a problem during the synchronization of the file to the device. How can I fix it? as I said before, this has not happened before.

  Hi UlloaC,

  See the steps mentioned in the link below that relates to a similar question

  http://www.Microsoft.com/windows/windowsmedia/player/Webhelp/default.aspx?&mpver=11.0.6001.7000&ID=C00D1236&ContextId=211&OriginalID=C00D1179

  See also the link below

  How can I fix sync errors?

• Windows Vista crashes due to the update of windows

  I just reinstalled Windows Vista 32 bit on my Lenovo PC after experiencing problems due to a virus. However, during the execution of that Windows update, I started noticing problems because my computer would freeze randomly. Neither the mouse nor keyboard would allow me an entry stop properly or to restart the computer, so I had to cut the power, whenever this happens. on the way back - turn on the computer, I noticed that the operating system is trying to update something and fails or succeeds every time. I know not why this problem occurs because I have a decent amount of DDR2 RAM (2 GB) and have even stopped to try to alleviate the problem of automatic updates.

  could someone please tell me what I could do to solve this problem, I try to install service pack 2 and see if this corrects the problem even though I have my doubts, it will be

  If you have backed up your data, format your hard drive, and then a clean installed Vista, STOP READING HERE and reply to this message.

  ==============================================

  Backup of personal data (which none should be considered 100% reliable at this point) then do a format and clean install of Windows.  Please note that another repair facility (upgrade AKA on-site) will NOT fix it!

  HOW to do a clean install of Vista: section "If you want to reinstall Windows Vista by running a new installation...". "of http://windows.microsoft.com/en-us/windows-vista/Installing-and-reinstalling-Windows-Vista#section_3

  Once installed the clean, you will have the equivalent of a "new computer" in order to take care of everything on the next page before connecting the machine to the internet or a network otherwise and before using a USB key that is not brand new, or has not been freshly formatted:

  4 steps to help protect your new computer before going online
       http://www.Microsoft.com/security/pypc.aspx

  NB: No matter what Norton or McAfee free trial which is preinstalled on the computer when you bought will be reinstalled (but invalid) when Windows is reinstalled. You MUST uninstall the trial for free and download/run the removal tool before installing updates, Windows Service Packs, or updates IE and before installing your new anti-virus application (which will require WinXP SP3 must be installed).

  Norton Removal Tool
       FTP://ftp.Symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

  McAfee Consumer product removal tool
       http://download.McAfee.com/Products/Licensed/cust_support_patches/MCPR.exe

  See also:

  Measures to help prevent spyware
  http://www.Microsoft.com/security/spyware/prevent.aspx

  Measures to help prevent computer worms
  http://www.Microsoft.com/security/worms/prevent.aspx

  Avoid fake security software!
  http://www.Microsoft.com/security/antivirus/rogue.aspx

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Windows cannot start due to software error: load needed for dll Kerneal

  Okay so a few minutes before I started to write this question I have connected my Xbox 360 controller to my computer. When I did the connection popup Wizard and asked to check the updates of windows to the right files to download to the controller. After that, he finds the correct files and downloaded said files. He then asked me to restart my computer for the software could take effect. Well, after that I did the error message, it's in the title, came on the screen and now my computer will not pass this error.

  Also I know you hear this is a lot but, honestly its really annoying that you don't have a phone number on your website

  MS10-047: vulnerability in Windows kernel could allow elevation of privilege

  http://support.Microsoft.com/kb/981852>

  The repeated failures to install KB981852 suggest very strongly that you see the effects of a rootkit infection W32/Alureon-Variant!

  Following the instructions on this site should help you:

  http://www.bleepingcomputer.com/virus-removal/remove-TDSS-tdl3-Alureon-rootkit-using-TDSSKiller>

  ~ or ~.

  Visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy.  If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.

  Buying to meet problems installing Microsoft security updates also can visit the following page for assistance:https://consumersecuritysupport.microsoft.com/>

  For more information about how to contact your local Microsoft subsidiary for security update support issues, visit the International Support Web site:http://support.microsoft.com/common/international.aspx>

  For enterprise customers, support for security updates is available through your usual support contacts.

• Cannot install Windows 10 because due to an error: 0x800704DD - 0 x 90016

  Upgrade Windows 10. Error code: 0x800704DD - 0 x 90016

  Through these steps that works for everyone who has tried to overcome failures in Windows 10 upgrade