With the help of keys to activate the buttons

Similar Questions

• Switch Cisco 2960/3560 = > recovery password and default settings with the button Mode

  Hi Experts,

  I have some confusion with the button Mode with cisco 2960/3560 switches.

  I read on many forums and articles, but where things are not clear.

  a place given 3 seconds and somewhere is given 7 or 10 seconds.

  Qus1), what is the exact time to press/hold Mode button to perform two following tasks:

  A. password recovery (according to my knowledge 3 sec) good or bad?

  Configuration of the switch (start + run) would be safe

  After the recovery of password? Yes or no

  B. factory default (according to my knowledge 10 dry) good or bad?

  I'm afraid, because if I press mode button more than 3 seconds, then

  It will delete any configuration of cisco switch. Yes or no

  Qus2) I want to recover the catalyst 2960/3560 switch password without

  Start/run configuration to lose. That is my main concern.

  Please tell me how to do this, what will be the time keeping Mode buttom

  in a few seconds?

  Qus3) which means this line

  "If the password recovery mechanism is disabled in switch

  then you will lose all the config.

  This sentence has been given on this forum url

  https://supportforums.Cisco.com/thread/140848

  KS

  Attach a terminal or PC with terminal emulation (for example, Hyper Terminal) port console switch.

  Use the following terminal settings:

  • Bits per second (baud): 9600

  • Data bits: 8

  • Parity: None

  • Stop bits: 1

  • Flow control: Xon/Xoff

  Note: For more information on the wiring and connection of a terminal to the console port, refer to connecting a Terminal to the Console Port of Catalyst switches.

  Unplug the power cable.

  The power switch and take it to the switch: command prompt:

  2900XL, 3500XL, 2940, 2950, 2960, 2970, 3550, 3560, and 3750 switches of the series, to do this:

  Press and hold the mode button located on the left side of the façade, while you reconnect the power cable from the switch.

  2960, 2970

  Release the Mode button when the SYSTEM LED flashes orange and then turns green. When you release the Mode button, the SYSTEM LED flashes green.

  3560, 3750

  Release the Mode button after about 15 seconds when the SYSTEM LED turns green. When you release the Mode button, the SYSTEM LED flashes green.

  The system was interrupted before the flash at the end file system initialization

  loading the operating system software:

  flash_init

  load_helper

  boot

  switch:

  Run the flash_init command.

  switch: flash_init Initializing Flash... flashfs[0]: 143 files, 4 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 3612672 flashfs[0]: Bytes used: 2729472 flashfs[0]: Bytes available: 883200 flashfs[0]: flashfs fsck took 86 seconds ....done Initializing Flash. Boot Sector Filesystem (bs:) installed, fsid: 3 Parameter Block Filesystem (pb:) installed, fsid: 4 switch: !--- This output is from a 2900XL switch. Output from !--- other switches will vary slightly.

  Run the load_helper command.

  switch: load_helper switch:

  Question the dir flash: command.

  Note: Be sure to type a colon ":" after the dir flash.

  Appears in the file system of the switch:

  switch: dir flash: Directory of flash:/ 2    -rwx  1803357                  c3500xl-c3h2s-mz.120-5.WC7.bin !--- This is the current version of software. 4    -rwx  1131                     config.text !--- This is the configuration file. 5    -rwx  109                      info 6    -rwx  389                      env_vars 7    drwx  640                      html 18   -rwx  109                      info.ver 403968 bytes available (3208704 bytes used) switch: !--- This output is from a 3500XL switch. Output from !--- other switches will vary slightly.

  Type rename flash: flash: config.old config.text to rename the configuration file.

  switch: rename flash:config.text flash:config.old switch: !--- The config.text file contains the password !--- definition.

  Issue the boot command to boot the system.

  switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC7.bin"...############################### ################################################################################ ###################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC7.bin" uncompressed and installed, entry po int: 0x3000 executing... !--- Output suppressed. !--- This output is from a 3500XL switch. Output from other switches !--- will vary slightly.

  Enter "n" at the prompt to abort the initial configuration dialog box.

  --- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Continue with configuration dialog? [yes/no]: n !--- Type "n" for no. Press RETURN to get started. !--- Press Return or Enter. Switch> !--- The Switch> prompt is displayed.

  At the switch prompt, type en to enter a mode.

  Switch>en Switch#

  Password recovery

  Type rename flash: config.old flash: config.text to rename the configuration file with its original name.

  Switch#rename flash:config.old flash:config.text Destination filename [config.text] !--- Press Return or Enter. Switch#

  Copy the configuration file in the memory.

  Switch#copy flash:config.text system:running-config Destination filename [running-config]? !--- Press Return or Enter. 1131 bytes copied in 0.760 secs Sw1#

  The configuration file is now reloaded.

  Replace the current passwords that you do not know. Choose a password with at least one capital letter, one number and one special character.

  Note: Replace passwords that are required. You must crush not all passwords listed.

  Sw1# conf t !--- To overwrite existing secret password Sw1(config)#enable secret !--- To overwrite existing enable password Sw1(config)#enable password !--- To overwrite existing vty password Sw1(config)#line vty 0 15 Sw1(config-line)#password Sw1(config-line)#login !--- To overwrite existing console password Sw1(config-line)#line con 0 Sw1(config-line)#password 

  Write the running configuration in the configuration file with the write memory command.

  Sw1#write memory Building configuration... [OK] Sw1#

  For factory reset:

  do not give under the control of factory reset

  Switch#copy flash:config.text system:running-config

  can I copy the running configuration to Flash

  Switch flash running-config #copy:

  Destination file name [running-config]?

  Building configuration...

  [OK]

  Switch #copy running-config startup-config

  Name of destination file [startup-config]?

  Building configuration...

  [OK]

  Review the link for more information below

  http://www.Cisco.com/en/us/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml

  Please note the useful messages.

  Concerning
  Vesta
  "Everybody is genius." But if you judge a fish by its ability to climb on a tree, he will live his entire life, believing that this is stupid. "

• Lightroom 6.6 Menu is not in line with the buttons

  After the upgrade to Lightroom 6.6 part of the menu do not align with the buttons.  For example, when you use the crop and straighten tool, next to the "Aspect" If you click on 'Original', a menu will appear with different options.  Before the menu seems very close to where I clicked, but since this last update it shows up in the lower left corner (essentially the opposite side of the screen).  See the screen capture below attached.

  Note that this happens with everything except menu for windows menu bar items (IE IE file, modify the work correctly, but others such as the Balance of whites, lenses, ect. correction show this problem).

  I don't know if that's a bug or an intervention of the strange apparatus that causes this problem.  I work on a Lenovo Yoga 2 Pro, so the screen resolution is 1800 x 3200.  It is also a touchscreen and 10 Windows running.    Note: I've also uninstalled and reinstalled lightroom, without modification.  Any help with this annoying problem would be appreciated.  Thank you.

  

  A known issue also noted in this thread-

  Some menus pop up in the wrong place

• Progress bar when audio plays on a slide with the button

  Hello

  I use 6 Captivate.

  I have a zipper opening for my demo that introduced the demo. This slide contains 1-3 minutes of audio. On this slide, I have a standard button named 'Start', that the learner must click Start the demo (which is on the next slide). I also have a PlayBar with rewind, Play/Pause, Back, Next buttons and Audio.

  Once the project starts, the Play/Pause button on the playback bar turns into mode 'Play '. This, I believe, is an expected behavior because of the presence of the 'button '. However, it causes me problems because, if the learner clicks on the 'Play' button (instead of the start or next buttons) after the end of the audio to the slide of the opening, the progress on the playback bar bar moves for the duration of the audio, so that nothing changes on the screen.

  Is it possible that I can:

  1. Move the progress bar with the button Play/Pause in "Pause" mode when opening, slide audio playback and switch to 'Play' mode once the audio ends? In this case,.

  a. If the learner pauses the audio by clicking Pause and then click on Play, it must continue with the audio.

  b. If the student click on the play button after the audio ends must take sound to the next slide.

  2. turn off the Play/Pause button so that the learner will not click on it?

  I don't want to hide the PlayBar on this slide as I want to give the Rewind option to the learner so play the audio again if he / she wants.

  Anthony

  A colleague found an easier solution than the one I was talking about earlier.

  He just moved the point to pause the start until the end of the slide button. Now, the progress on the playback bar bar moves with audio and the Play/Pause button passes in "Play" mode when audio stops at the end of the slide. On clicking the play button, the project will move to the next slide.

• Need help with the button mute on my helmet XL-3000 of Microsoft Chat, please!

  Hi all!  Hope everyone is having a good TGIF!  If you use my helmet even, I need help understanding the region button mute in the middle of the rope.  The red light is on or off?  I suppose that if I hit the curve button with the microphone on this subject, and the red light, I'm turn off my mike?

  I did some tests with others on the phone calls.  Sometimes, some other hear me, sometimes they do not have.  BUT I NEVER HEAR THEM!  FOR MY WORK, IT IS IMPERATIVE THAT I MAKE CALLS TO OTHERS!  HELP PLZ!  Thank you very much and have a great wkend!

  Hello
   
  Please follow the links below to troubleshoot the computer.
   
  Method 1
   
  Connect one microphone, music player or other audio device to your computer
  
  http://Windows.Microsoft.com/en-us/Windows7/connect-a-microphone-music-player-or-other-audio-device-to-your-computer
  
  Method 2
  
  Step 1
  
  Troubleshooting: headsets
  
  http://www.Microsoft.com/hardware/en-us/help/support/troubleshooting/headset/microphone-issues
  
  Step 2
  
  Open the troubleshooting of Audio recording
  
  http://Windows.Microsoft.com/en-us/Windows7/open-the-recording-audio-Troubleshooter
  
  Method 3
  
  How to adjust the microphone volume
  
  a. click Start, type mmsys.cpl in the search box and press ENTER.
  b. in the sound dialog box, click the recording tab.
  c. click Microphone, and then click Properties.
  Note Make sure that the work appears under Microphone. If the job does not appear, click Microphone, and then click on set as default.
  d. the Microphone Properties dialog box, click the custom tab.
  e. select or clear the box amp Microphone.
  f. click the levels tab.
  g. set the volume to the desired level, and then click OK.
  h. click OK to close the sound dialog box.
   
  How to adjust the setting of the voice
   
  a. start the game.
  b. connect to LIVE (the Guide).
  c. click personal settings.
  d. click on voice.
  e. make sure that the recording volume level indicator records at a bar when you talk.
  f. click done.

  If you are still facing problems then, I would say that you contact support for Microsoft hardware for more direct intervention.

  http://www.Microsoft.com/hardware/en-us/support

  
  I hope this helps.
  
   

• Help! with the buttons

  Hello
  Scenario #1: I created an image in Flash CS3, I use with Actionscript 2.0. I have 12 small pictures on the chassis that are buttons.
  Scenario #2: In a single frame, I added a clip that is 12 larger images and a description of each in their own framework along the time line.
  
  Try as I might I can't work, how the buttons work. I want the user to click on one of the buttons and for the enlarged image in the clip to appear in the main part of the film.
  Here is a link to some screenshots of what I did.
  http://www.michaeltaylor.biz/Flash/buttons.html
  
  
  Can anyone help, or does anyone know of a tutorials that deal with what I can have a look at.
  
  Thanks in advance
  
  Michael

  It's always a bit difficult to say how you have things set up, but here's a solution possible scenario...

  First of all, you have essentially 13 points, 12 buttons and a movieclip with larger images. Give all instance names in the properties panel.

  Let's say that you named the first button: btn1
  and the movieclip is named: imgs_mc
  and the first image of the movieclip aligns with the btn1 goal...

  Btn1.onRelease = function() {}
  imgs_mc.gotoAndPlay (1);
  }

• Problem with the buttons 'Internet' and ' CD/DVD"on the Satellite X 200 - 22U

  Hello

  I use a laptop Toshiba Satellite X 200 - 22U with Windows Vista Home Premium.
  My problem is: I want to create an application to start with multimedia keys ('Internet', 'Disc'). I registered it with TOSHIBA, but the buttons ' CD/DVD' and 'Internet' do not work. In the TOSHIBA Assist Button Manager software, I see "¥" (yen mark) instead of the "------" (backslash) in the path field. I checked it in REGEDIT, where everything is OK, I see the path correctly. But these two buttons do not work. ' Play/Pause', 'Stop', 'Previous' buttons 'Next' work with Windows Media Player.

  Please, help to solve my problem!

  Thank you
  McLawrence

  Have you installed the latest version of Toshiba Assist?
  To do this, look on the Toshiba site and also check if there is a new BIOS.
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

• RH9 WebHelp problem with the buttons next and previous topic

  The previous topic and next topic buttons do not work as expected. By example, if I navigate to topics and click on the previous topic, I expect to see the most recent section I read (similar to the use of the back button in a browser to see the previous page). However, the previous button is not available or the user to a random topic and next topic never brings up the next topic.

  I inherited this project, my first experience with RH9 and so am not sure something previous author included in the project to check the buttons appear or if these buttons are part of the interface default WebHelp. I looked in properties available to single Source for each output, but do not see any place to specify information on these buttons.

  As you can see in the screenshot, is not on the sequences of travel (I saw that there are other questions about Next and Previous as sequences associated to browse).

  Any help appreciated because this bug was found by QA and they would like to solve the problem in the next update...

  Carol

  Hello

  These buttons above the table of contents are buttons for the navigation sequence. And that might explain their behavior.

  Do you mean any other key? Am I missing something?

  Take a bow

  Willam

• Satellite P300 - problems with the buttons of enlightenment

  First of all, I would like to apologize for my bad English, I'm French actually.

  Hi, I bought a laptop Satellite P300, a couple of days, and already I have a problem with tactile keys (one on top of the keyboard).

  Actually, the only one of the left, which is supposed to turn off the sound used to keep away the keys lights and Satellite logo. One day (and I don't know why), when I pressed her, she actually cut the sound. And now, the first two keys (mute and shortcut of windows media) do not work, but the other four (Media Player control).
  I tried Toshiba Assist, and the tool for the configuration of the pushbuttons (I don't know the English name of this tool) but I couldn't set the keys, they were not on the list "button name".

  So, does anyone have an idea how to solve this problem?

  I apologize again for my English.

  Hello

  I assume you are using Windows Vista because you bought the laptop a couple of days and so I think that you should try to reinstall the Toshiba value added Package. This package determines the buttons of the lighting that you mean and others (for example the FN keys too).

  The latest version, you can download the Toshiba site:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  1. download the latest PPV on the Toshiba site
  2. go in Control Panel > Add/Remove programs. Find the Toshiba value added package and remove it
  3. restart the laptop
  4. download and install CCleaner. This cool cleans up the registry of Windows and system files. He should find some registry keys of Toshiba you should remove with CCleaner.
  5 reboot the laptop
  6. install the PPV that you already downloaded
  7 restart once again

• The sign @ arrives with the ' button and the "comes up with the 2 - How can I fix?"

  The @ sign with the ' key and the 'types of sign with button 2.  How can I fix?

  It looks like your dad keybaord was put at the disposal of the UK.  This can happen if you accidnetally you press a special combination keys that been implemented as the means of getting that deliberately.  Here's what to do: -.

  1 go to Control Panel, region & language, keyboards & languages, Change keyboards, general tab, select the correct keyboard in your area * if isn't one already shown [click on Properties... to see a preview of the keyboard layout] or click Add... & Select a new keyboard from the list [while you are in the list, click on the Preview button to see a preview]. When you have finished adding a new keyboard, move it to the top of the list using the buttons on the dialog box.

  [* The region for which the keyboard was made and for which its route has been set.  [I understand that there is a "US International keyboard" who suffers from this confusion between change quite easily, unless you have a need for special versatility, choose a keyboard layout United States specific instead if you find that this is what has been implemented on your system]

  2 then go into Control Panel, region & language, keyboards & languages, Change keyboards, tab bar of language and, if you regularly change the language settings, make the hidden language bar.

  3 then go to Control Panel, region & language, keyboards & languages, change keyboard, tab Advanced key settings where you can see the shortcut key sequence that could you have this problem by chance. You will also see the change key sequence that you may want to change by clicking on the button change the key sequence and affecting the switch input language & keyboard Switch not [when I changed them, I had to set not to switch input language and accept the change, then return to the dialog box set not to switch keyboard configuration].

• Control edge file animate OAM with the buttons play/pause of Captivate on the skin.

  Hello world

  I worked on a project where I mix a variety of objects and animations.  I do animations animate on board.  The problem I have is that when the user clicks the button pause on the Captivate playback controls, the oam file do not pause.  I found descriptions of how I can make an animation to play/pause the Captivate timeline button on board, but I can't find anything on the use of the Captivate pause button to control the Edge file animate.  Discussions only that I managed to find on that seem to be the answer.  Someone had a bit of luck with this question?

  Any advice would be appreciated.

  Thank you

  Randy

  OK, it's a bit hacky, but it works quite to control the main timeline object in a file of edge of Cape Town, where the Edge file has been imported to Cap 9 as a Web (oam) object. I went seeking answers same like you and came from vacuum, then start to tinker myself and came across the following method.

  Let's use window.postMessage to send a string between Cape document window and document edge iframe window then react accordingly. You can learn more about postMessage accepted battery answer here: http://stackoverflow.com/questions/3076414/ways-to-circumvent-the-same-origin-policy

  In your dashboard file click the support of Actions for the stage object in the timeline and select the compositionReady event. Paste this code into the text window:

  addEventListener for Chrome, attachEvent for IE

  window.addEventListener ('message', receivedFromCaptivate, false);

  window.attachEvent ('onmessage', receivedFromCaptivate);

  function receivedFromCaptivate (event) {}

  switch (event.data) {}

  case "play":

  SYM. Play();

  break;

  case "pause":

  SYM. Stop();

  break;

  }

  }

  Save the file and publish it as an oam, then import the OLS in a slide of Cap, as you normally would. Now, to put in place things of the CAP. Here is a visual aid for the rest of the explanation...

  

  In the PAC file select the control that you use to start playing the chronology of the edge (in the example above the "slide4Play"), select the checkbox 'Use as button' in the properties on the right, select the "Actions" tab, then to the drop-down list for 'Success' choose "Execute advanced Actions." Click the folder next to the selection of Script control and advanced Actions dialog box should appear. Name your action something (for example, "playEdgeSlide4"), then click the 'Add' in the grey bar to add a new action in the queue. In the drop down "Select Action"... ", choose"execute Javascript. "In the drop down menu"select the window... ". ", choose"current ". Then click on the 'Script_Window' button to bring up a window of text Javascript crap. In this window, you can paste this:

  try {}

  $("iframe") [0].contentWindow.postMessage ("play", "*");

  } catch (e) {}

  Console.log (e.message);

  }

  Select 'OK' to close the window of text Javascript crap, then click the 'Update Action' button to save your new action. Now let's do the same for break action - select the control that you use to pause, go through the steps above, the name of the action, implement advanced action in the same way and in the Javascript crap text window, paste the following text:

  try {}

  $("iframe") [0].contentWindow.postMessage ("break", "*");

  } catch (e) {}

  Console.log (e.message);

  }

  Cap incorporates the Edge file in an iframe on the page that has its own document window. In order to communicate between base ceiling windows and the iframe, we use the postMessage call. So when you hit your button Pause/Play in Cape Town, he publishes an event to the function that gets recorded in the iframe on board. And in the event.data is the string we send above the Cap base window in the function postMessage ('play' or 'pause'). We use a simple switch to react to the data string, stop or have fun with the main symbol of the scene at the edge (sym.play(1000) (), sym.stop ()).

  I hope this helps!

• Access of undefined property _btn (problems with the buttons)

  I get this error message:

  Scene 1, Layer 'actionscript', frame 1, line 1

  1120: access of undefined property tennis1_btn.

  Scene 1, Layer 'actionscript', frame 1, line 7

  1120: access of undefined property tennis2_btn.

  Scene 1, Layer 'actionscript', frame 1, line 13

  1120: access of undefined property tennis3_btn.

  Scene 1, Layer 'actionscript', frame 1, line 19

  1120: access of undefined property tennis4_btn.

  Scene 1, Layer 'actionscript', frame 1, line 25

  1120: access of undefined property tennis5_btn.

  Scene 1, Layer 'actionscript', frame 1, line 31

  1120: access of undefined property tennis6_btn.

  Here is a screenshot of my code

  

  I'll also paste below:

  tennis1_btn.addEventListener (MouseEvent.CLICK, gotennis1);

  function gotennis1(event:MouseEvent):void {}

  var gotennis1url:URLRequest = new URLRequest ("juniortennis.php");

  navigateToURL (gotennis1url, "_parent");

  }

  tennis2_btn.addEventListener (MouseEvent.CLICK, gotennis2);

  function gotennis2(event:MouseEvent):void {}

  var gotennis2url:URLRequest = new URLRequest ("adulttennis.php");

  navigateToURL (gotennis2url, "_parent");

  }

  tennis3_btn.addEventListener (MouseEvent.CLICK, gotennis3);

  function gotennis3(event:MouseEvent):void {}

  var gotennis3url:URLRequest = new URLRequest ("http://abbottsports.com/membership/memberships.php#tennis" ");

  navigateToURL (gotennis3url, "_parent");

  }

  tennis4_btn.addEventListener (MouseEvent.CLICK, gotennis4);

  function gotennis4(event:MouseEvent):void {}

  var gotennis4url:URLRequest = new URLRequest ("staff.php");

  navigateToURL (gotennis4url, "_parent");

  }

  tennis5_btn.addEventListener (MouseEvent.CLICK, gotennis5);

  function gotennis5(event:MouseEvent):void {}

  var gotennis5url:URLRequest = new URLRequest ('calendar.php');

  navigateToURL (gotennis5url, "_parent");

  }

  tennis6_btn.addEventListener (MouseEvent.CLICK, gotennis6);

  function gotennis6(event:MouseEvent):void {}

  var gotennis6url:URLRequest = new URLRequest ("tenniscourts.php");

  navigateToURL (gotennis6url, "_parent");

  }

  Please help: I have a couple of them types of menus, but it's the only one that gives me problems.  Here is the site that I use on:

  www.abbottsports.com of work

  http://abbottsports.com/football/football.php Working

  http://abbottsports.com/Motocross/Motocross.php working

  I add another on our page of tennis. I just copied the flash files on my tennis records and renamed all tennis instead of football, including buttons, as you can see on the right side of the page in the photo.

  I'm sure it has something to do with me rename the button, because I never changed anything in the code except substitute the word tennis football in each place. and renamed my buttons to tennis instead of football.

  Thanks for any help.

  Instance names your buttons are 'football1_btn '... 'football6_btn '.

  Rename them to "tennis1_btn"... "tennis6_btn" and you're golden.

• Problems with the buttons (on the area of State/Hit)

  The site I'm getting is:

  http://www.RelicRockBand.com

  If you go to the "Biography" section, you'll see four links that work as buttons of reversal.  Now, if you go to the 'Media' section, you will see 6 links that do not appear to react correctly as buttons of reversal.  They fulfill their function, but it is difficult to get the button to appear in its "underline" in the State.  I don't know if it is a problem with the over State, the status of success or another problem with how I built the site.  If you want to take a look at this, go to:

  http://www.uvm.edu/~nmphilli/Relic_Website/Flash/Relic_Webpage.fla

  to get the FLA for the site.  The concerned items are nested as follows: in scene 1, on the content layer, label image 'Media' (frames, 16-21), you will find Media_Fader, where is Media_Content, in which are several buttons, each with getURL actions that are applied to them.  Any help would be fantastic!  Thank you!

  -Nic

  The question always involves using the textfield links.  Remove the textfields in all settings inside the buttons and your problems should go away.

• How to make a menu with the button this opening fade?

  I have built a menu animated in AE and had added text that melted by layer layers/buttons > still > create button. Once I have import into Encore through hotlinks I can't connect the buttons in the menu application.  I have added a sample.
  
  Basically all I want is the feature of game, selection of scene and credits to be selectable after completing discoloration in @ the: 20 mark. I don't want the menu's loop.

  I tried to do a static menu (from the last image in AE) play after that, but there is an a second gap or two before this static menu plays that look just sticky. I tried this in the preview, and it made on a dvd with the same result.

  All the tutorials I've met really does not answer this question either.

  Any help would be appreciated.
  
  Thank you

  So you're on the right track.

  This departure for a workflow I would try if I did more menus animated.

  http://help.Adobe.com/en_US/encoredvd/4.0/WSA5513911-0AD1-440C-BDAD-2E0E806B425E.html

• Problem with the button 'next' sideshow & amp; Links

  Hello
  
  I am trying to create a slide show that has a 'next' and 'previous' button that allows you to see the next or previous movieclip when you click one of the buttons, and each movieclip contains a link to a Web site. Please see an example of what I've done so far - http://abwebsitedesign.co.uk/flashtest/
  
  The code I used for the links doesn't work, when you click a clip he only takes you the first url (which is the "Greenfield" in this case, but when you're on the image of "Millstock" do not you on 'Millstock' site, still need you to "Greenfield" one). Also, when getting to the last image, then click on 'previous', the 'next' button should appear, but is not, it shows that when you click on the "back" button 2 times. Please let me know if anyone can help with this! Attached, is what my code looks like.
  
  Thank you very much.

  Hello

  I think that your table indexing and counting is a bit off. If you change your managers of button for the code below, you should see your URL works correctly and your next and previous buttons works as it should.