WLC 5 GHz active SSID not visible in the available networks
We use WLC 2504 with 2 AIR-CAP2702I-D-K9Access Points. I am facing a problem of slow performance with customers active wifi (Macbook Pro). As all the clients that we use are computers laptops Macbook Pro who takes supported 802.11ac, I created a new WLAN (SSID) with Radio 802 11 a only to force all laptops to use the 5 Ghz band to check that it makes the difference. The SSID is not visible as a network available on the client if the radio SSID is set to "802. 11 a only"if it is marked to broadcast the ssid. '802.11ac' is also enabled in the network "802.11a/n/ac" categories of wireless.
That means my Access Points do not support the 802.11ac?
Yes, the Country is set to US which is not correct, Does it make any difference?As Leo does, that's the problem. Configure the appropriate country code where this access point works (appropriately by the detail of the AP, India). See below http://www.cisco.com/c/en/us/products/collateral/wireless/access-points/product_data_sheet0900aecd80537b6a.html see this post to see how you can configure https://mrncciew.com/2013/04/07/configuring-country-codes-on-wlc/ HTH Rasika * Pls note all useful responses *.
Tags: Cisco Wireless
Similar Questions
-
BlackBerry Smartphones my caller ID is not visible on the phone of receivers
When I call someone, my number is not visible on the phone receivers. I have enabled Caller ID, but it does not always show.
I have a Bold 9000.
Any suggestions how to solve this problem?
Hiya!
Does show anything at all? or just "Unknown"?
You said that you check what ID caller is activated?
Phone key > Menu key > options > General options > Show My Number is set to 'Yes' and limit my identity is set to 'network '?
-
Operations are not visible in the viewport in the develop module only in the browser window.
1.I have a very strange problem with Lightroom 6.5 and earlier versions had some of the problems (so little reliable, because I don't know what time it will happen again) Lightroom if I work after a while, the following occurs: in the large screen of the applied rendering operations are not visible, only the small window of browser. In the middle of the screen is NOTHING done, so I continued to work on the image in the window of exploitation and not the image disappears, just a gray window remains above. Dan I switch to another view and then be visible again (but operations also do not appear this, only in small browser window displays the changes applied) I have to restart your PC for vouchers, which sometimes does not occur when you restart. Function the GPU turned power off.
2. at this moment, there is a new problem starting.
Lightroom begins only with color boxes in the grid, no image is visible
My system configuration: Windows 7, 64-bit Intel Core i7 - 3770 k CPU 3.50 GHz 16.0 GB RAM ATI RADEON 4800 series
This could be caused by a defective monitor profile.
As a diagnosis too, l and, possibly, a temporary solution, try to set the monitor to sRGB profile.
If this solves the problem, you need to calibrate the monitor with a standard material.
This will create a new profile that accurately describes your monitor.
Press the Windows key + R, type colorcpl, and then press ENTER.
Add the sRGB profile, and then set as default profile.
-
How can I just disable logging in El Capitan? It is not visible in the disk utility when you press alt and file!
Mac OS X: about the logging of system - Apple Support files
Hope this helps, good luck to you.
-
My Hotspot is not visible in the settings
I update my iPhone to iOS 9.3 6s my hotspot is not visible in the parameter I update my iPhone of many other iOS version 9.3.1 to 9.3.3 and 9.3.4 9.3.2,and need help.
Hello
To configure Personal Hotspot, follow the instructions here:
To help to solve problems with your hotspot, follow the steps detailed here:
-
Icon not visible in the browser bar Firefox 40.0 report. Report of uninstalled, installed report 3.6.1507.14; restart the Mac under OS X 10.10.4 Yosemite. Still no report icon. Report NB icon present in Safari 8.0.7 and extras Menu.
I'm not entirely sure about the feature you request on the subject, but here's what I could find:
-
Comments on CNET articles are not visible in the x 64 every night
If you open any page of the CNET article for example URL below, there is a bar with a 'Comments' button and a few other links Twitter/Facebook/etc.
http://News.CNET.com/8301-11128_3-57342036-54/Volvo-plug-in-diesel-hybrid-races-into-Europe/
This bar is not visible from the x 64 Nightly build, even with all extensions disabled. It is visible that if I start Firefox in Mode safe.
I find it strange because apparently it is disable the extensions I've already done manually and turn off any custom parameter and the theme that I don't have.
Looks like a bug on the side of Firefox, as the same page works fine in IE and Chrome, and, as I remember, in the 32 official output x. Any idea?
I see the same thing with the current 32-bit Nightly build on Linux.
Looks like a problem with the JIT compiler.It works if I set javascript.options.methodjit.content to false.
A good place to discuss problems with Firefox nightly builds and Firefox beta builds is the forum mozillaZine Firefox builds.
There is also a thread every day to discuss problems with the last Nightly build on the build from mozillaZine forum.
You must register on mozillaZine forum site to post in this forum. -
Share photos added to the photo library via the menu are not visible on the Photos
Hello
I started using DxO OpticsPro 10 to process Raw files. When I used the share menu in this application to "Add photo" pictures are exported but not visible in the Photos app. I see that they are in the photo library (Show Package Contents > Masters), but they are not visible in the Photos in the Photos app. However if I use "Export to Application" instead of "Add photo" in DxO OpticsPro the Photos app opens and the image is visible.
You can't always do and changes directly to the photo library - you must use the program of Photos to import photos - adding photos to the library has no positive effect (and may even cause problems)
LN
-
DVD/CD drive is not visible in the Device Manager, but it works.
Original title: My dvd/cd drive is not visible in the Device Manager but
This works because I have jst begin with him. I can hear the disc running, but nothing ever comes and when I go to computer its not visible there either.
Hello
See the methods listed in the article mentioned below.
My drive does not appear in Windows Explorer
http://support.Microsoft.com/kb/330140
Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 how to back up and restore the registry in Windows.
See this link to view the hidden devices:
http://msdn.Microsoft.com/en-us/library/Windows/hardware/ff553955 (v = vs. 85) .aspx
I hope this helps!
-
Taché product key
HelloI try to install vista on my laptop but a letter of the key is not visible, all the other parts are very well including the serial code, is there another way to get the key of the other information? The laptop currently has non-OS I've tried to reinstall.
Thank you
Scott
Product keys are bit-agnostic - they don't care if it's 32-bit or 64-bit.
However, cannot legally use the recovery disk from one computer to a different constructor machine - as other licenses are not properly paid..
There is nothing nonetheless to try all possible variations on the absence of character (there are only 25, after all the
) Other than that, your best option is to contact the manufacturer and order a set of recovery disc for the machine. I do no download available for Vista with SP2 - but you can download Vista with SP1 and create the disc.
http://www.heidoc.NET/Joomla/technology-science/Microsoft/57-Windows-Vista-direct-download-links
-
computer Vista Home network is not visible from the XP computers
I have a home network with 4 computers. Both run Windows XP, Windows Vista is running and
It works in Windows 7. Each group can see all the others and can access shared files and printers
with one exception. Vista computer is not visible from the XP computers. It is visible from
the Windows 7 computer. I guess that there is a setting somewhere on the Vista machine
That I need to change, but I'm not.Thank you.
David
Hello
see Help for these links if
Networking of computers running different versions of Windows
http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-home-network
Setting up a network home
http://TechNet.Microsoft.com/en-us/library/bb727037.aspx
Vista File and Printer Sharing
-
typed letters are not visible after the end of the custom field in editfield
class CustomEditField extends EditField {}
CustomEditField (String text) {}
Super("",Text);
}
public void layout (int width, int height) {}
Super.Layout (getPreferredWidth (), getPreferredHeight ());
setExtent (getPreferredWidth (), getPreferredHeight ());
}
public int getPreferredHeight() {}
Return super.getPreferredHeight ();
}
public int getPreferredWidth() {}
return (Display.getWidth () * 2/3);
}
}
It's my edit custom field.
When I type on this field and reached end of the field, can't see the letters after that, but I can type (the only thing is to type letters are not visible after the end of the field)
What is the solution
I'm sure that you must explicitly enable scrolling. See Manager javadocs.
In addition, you limit the scope of your field, which may also fail to scroll.
-
connect with vm via VMRC console is not visible in the self-service portal
Even after providing the actions required, I do not get this option "connect with vm via VMRC console is not visible in the self-service portal. Anyone who can help me in this?
https://www.VMware.com/support/Vcac/doc/vrealize-automation-62-release-notes.html
6.2 additional:
VMware Remote Console (VMRC) is disabled for vSphere machines *.
Action connect using VMRC for vSphere machines has been deleted due to a security breach. Access remote console for machines provided by vCloud Director is not affected. For more details on this topic, see VMSA-2014-0013.
Thank you
Kumaran
-
I finally got CS2 installed on my system. But now the drop-menu background color is black and the elements are not visible until the cursor is over them. It is very difficult to read. How can I change this? I tried to go into change preferences but it does not work
I changed it to the value default them and that worked. Thank you very much
-
Hi - I'm looking for the correction Adobe Illustrator 2014 1.2 update (ou.0.2) for Mac - and it is not visible in the Adobe Creative Cloud Packager (Mac version). The only visible update is Illustrator CC 20141 - that is what introduced bugs.
The only thing I can think that may cause the problems I have a Mac Mini on the Mavericks.
Dave
Hello
I discovered that my question above is a non issue. A user has triggered by watching the below article on Illustrator 2014 17.0.2 cc
http://helpx.Adobe.com/Illustrator/release-note/Illustrator-17-0-2-release-notes.html
He had recently improved to wht, we know now is 18.0 to 18.1, which is the latest version. He has read the foregoing artic
the and assumed that it was a version of fixed a bug for its version - as the number of ov18 v17 is not displayed. It is usually just 2014 CC.
I asked him to post a bug report on Adobe Illustrator CC 20141
Dave
Maybe you are looking for
-
How can I remove keyboard AutoCorrect?
I'm not a developer, just an ignorant American user. I want to disable auto correction of typing
-
Access to the wireless network
All of a sudden I can't access my wireless network that I use for this computer for 2 years. My modem works as I have tested. But it does not find my wireless network.
-
How can I make the CONNECTION wireless at the insertion of the ethernet cable?
I have a Windows 7 computer laptop and a computer laptop Windows 8 . On two laptops, I'm leaving both wireless and wired adapters enabled and on my laptop Windows 8 , when you insert the ethernet cable, the IDEALLY AUTOMATICALLY DISCONNECT wireless b
-
Call APP_TYPE_CAMERA on 4.5 os RuntimeException
try { Invoke.invokeApplication(Invoke.APP_TYPE_CAMERA, new CameraArguments()); } catch (Exception e) { Dialog.inform("Could not start camera."); } Hello! Such a code, I try to start on 4.5 JDE (8700g Simulator). EI As RuntimeException exception with
-
Lenovo x 201 3249cto, 4 GB ram, 128 GB SSD, win7 64-bit Is it better than BIOS upgraded when the new Version of BIOS is made available? My installed Version - the 1.23 New Version available - 1: 31 (do not have) Also, what is the easiest way and inst