Workstation 9.0.1 rather than network (PXE) boot

Similar Questions

• SG300-52. Prefer to send traffic to the default gateway rather than static route? Network stops if I disable ICMP redirects.

  I have 4 switches, each act as their own with a 26 subnet mask. They have static routes for every other switch. The firewall has a static route to each switch. If I unplug the LAN of the Firewall interface, traffic stops the flow of the switches. If I block the side LAN firewall, ICMP redirects, traffic stalls outside.

  So if you are connected to this switch, say that you pull an ip address of 192.168.122.20. Your front door is the 192.168.122.62 switch. If you try to access a server 192.168.127.142, the SG300 sends your traffic to 192.168.127.254 to get an ICMP redirect, rather than simply to communicate directly with 192.168.127.50.

  My network 'basic' is 192.168.127.0/24 vlan1 and the firewall is 192.168.127.254

  This is the route of one of my switches table (which has 192.168.122.0/26 and ports run on vlan122)

   Maximum Parallel Paths: 1 (1 after reset) IP Forwarding: enabled Codes: > - best, C - connected, S - static S 0.0.0.0/0 [1/1] via 192.168.127.254, 73:48:13, vlan 1 C 192.168.122.0/26 is directly connected, vlan 122 S 192.168.123.0/26 [1/1] via 192.168.127.123, 73:48:13, vlan 1 S 192.168.124.0/26 [1/1] via 192.168.127.124, 73:48:13, vlan 1 S 192.168.125.0/26 [1/1] via 192.168.127.125, 73:48:14, vlan 1 C 192.168.127.0/24 is directly connected, vlan 1 

  In any case, what gives? Why the switch would first try to send the stream to the firewall?

  EDIT: Here is the server routing table:

   [email protected]/* */:~$ ip route show default via 192.168.127.254 dev eth0 192.168.122.0/26 via 192.168.127.122 dev eth0 192.168.123.0/26 via 192.168.127.123 dev eth0 192.168.124.0/26 via 192.168.127.124 dev eth0 192.168.125.0/26 via 192.168.127.125 dev eth0 192.168.127.0/24 dev eth0 proto kernel scope link src 192.168.127.142 

  Hi Jonathan,.

  I'm sorry. I misunderstood the routing table you want to accomplish. Your concern seems relevant given that the matching rule more will be selected instead of one: page 275 http://www.cisco.com/c/dam/en/us/td/docs/switches/lan/csbms/sf30x_sg30x/...

  ... "When the routing of traffic, the next hop is decided based on the longest match on the prefix (LPM algorithm). A destination IPv4 address might match several routes in the IPv4 static routing Table. The device uses the matching route with the higher, subnet mask that is, the longest match on the prefix. "...

  So go ahead and report it to the support team so the guys can make the laboratory, confirm it and declare additional:

  http://www.Cisco.com/c/en/us/support/Web/TSD-Cisco-small-business-suppor...

  Kind regards

  Aleksandra

• I downloaded and installed it and TB preconfigured mailbox of my wife rather than create a new one for me. Whats up with that?

  I downloaded and installed it and TB preconfigured mailbox of my wife rather than create a new one for me.
  The first time I ran it, there was his box mailbox and all the msg I whatever it either has no entry for a server, the login or password. IOt just configured everything to his mailbox! He did this IP address or what?

  Network, what type of network? you have a server?

• How can I get my NICs tp pass rather than fail?

  How can I get my NICs tp pass rather than fail?

  Hello

  ·         What exactly are you trying to do?

  ·         What is the exact error message that you meet?

  ·         Since when are you facing this problem?

  ·         Are you able to connect to the network?

  ·         What type of network connection you use (wired or wireless)?

  Please provide details so that we can help you in a better way.

  I suggest you check in SafeMode with network you are able to connect to the network or not.

  a. restart and keep tapping F8 until you reach the start menu.

  b. choose Safe mode with network and press ENTER.

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.

• When you move the cursor, rather than move, the police often changes a size big or too small to see.

  Original title: "when I try to move the cursor, instead of move, the font size often changes to a huge size or one size too small to see. In addition, it can jump to the top or the bottom of the page. »

  More I use Vista, more I hate it!

  It came pre-loaded on my Fujitsu Lifebook. I had heard talk were many complaints about Vista and I wanted to stay with XP or Windows 7.  Each manufacturer of the laptop has been unfortunately Vista preinstallation.

  • When I use the word processor Works Windows, sometimes without warning he automatically becomes italic police without any input from me.
  • If on Windows works WP or on any page of e-mail online, when I starts to move the cursor, a little 'target' - as the icon appears when the cursor was and, either changes in font size of microscopic or 500% or more.
  • On the Internet page of wole can shrink or get huge.
  • At other times, with one touch of the mouse or touchpad, rather than the font change, the cursor may disobey my entry and the end to the top at the bottom of a page where I won't be, or somewhere else. When I get back to the expected location, it can repeat the same action three or four consecutive times before to behave normally again.  This makes typing manuscripts or very frustrating messages sometimes, not to mention a lot of lost time.
  • When you try to type copy from a printed script, if I don't keep control of the screen I can finish with margins stange, italic where they belong or phrases that are moved where they belong.
  • Sometimes when I'm trying the high - lite a word or phrase so I can drag it to another location, it will refuse to high light, making necessary use rear brace to delete the words I want to drag and retype the words to the new desired location.
  • Another problem is that the will of cursor down stubornly and turn several times since the location of the Center to the extreme side so that the rest of the page is covered.  Vista seems to have a mind of your own.

  This set of problems seems to migrate from MS Word to MS Works, Web pages, and e-mail message composition.  I thought it was the new computer initially. I even returned it to Fry's electronics for maintenance two times.  I mean, they just excanged for another new Fujitsu Notebook.  When I got home, the replacement computer have behaved in the same way, which indicates that it's the software, not the hardware.

  Funny thing - now that I complain on this topic in this forum and have written this much, it doesn't have behaved badly again!  The ghost of Vista must have been scared and went into hiding.  ;-)

  Yet once more I use Vista, more I hate it!  -especially since I was in the middle of writing a book for publication.  In light of the frustration and the loss of my precious time because of these persistent bugs in recent months, I wish MS would trade my copy of Vista for Windows 7.  MS seems to be getting a reputation for releasing Beta quality software and call it a finished product.  You would think that MS wakes up to the fact that consumers expect to have for their money.  Everyone has the same problems?

  Are there realistic solutions out there?    Hmm, no spell no checker on this page.  Sorry for the typos. :-)

  You can get in trouble with your mouse device drivers, firmware and/or software.  This may be due to a Microsoft Update or any number of things (and could have happened to these two machines, if you did the same thing in both cases).  Go to the Device Manager by going to start / find and type Device Manager and enter and then double-click on the program icon that appears.  Check each device to a red x, yellow! or white?  These identify devices with problems probably (drivers, but also of conflict or something else).  Click on each for more details and troubleshooting tips.  If you need to get drivers (and you should get for your mouse at the very least and I consider the keyboard as well and make sure they are compatible with your device, and your version of Vista) and all you have time to do - they can help way beyond simply solve this problem) leave the computer dealer or the manufacturer of the device (NOT of Microsoft Updates).  In fact, you must disable automatic updates in Windows Update driver as follows:http://www.addictivetips.com/windows-tips/how-to-disable-automatic-driver-installation-in-windows-vista/. Follow these steps to get the drivers: http://pcsupport.about.com/od/driverssupport/ht/driverdlmfgr.htm.  Once you have the drivers, you can install them via the Manager device as follows:http://www.vistax64.com/tutorials/193584-device-manager-install-driver.html.

  Also, your mouse may have the functionaality to change the font sizes and jump from one end of the screen to another by doing some things.  Read the user manual and/or research through start / Control Panel / mouse to see if this is the case and if so, it may be able to be disabled.  The problem with some of these "features are that if you don't know about them they can cause difficulties when they activate for apparently no cause when you actually not what caused the feature must be enabled." It took me a while to realize the CTRL-0 would change my IE screen at 100% size and I first thought there was something wrong until I discovered the problem by chance.  I say that, because the odds of two computers with the same exact defect are astronomical - it looks more like a problem as described above or a certain type of function you are unaware of (perhaps in combination with a keyboard input that is why I suggested that you update those as well).

  I hope this helps.  If not, I am sorry to say that your best option would be to go back again to see if they can reproduce the problem (you use your way computer in case it is something you do) and either repair or replace again (or change to another computer entirely).

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Drive mapping: How can I get my external drive be mapped to F: (as he was once) rather than g: which is what happens when I turn on now.

  How can I get my external drive be mapped to F: (as he was once) rather than g: which is what happens when I turn on now.  I tried to unplug and power, reboot etc.  There is no F: drive connected to the computer.

  Go to start / Control Panel / administrative tools / computer management / "disk management and select external reader by clicking on it and then right-click on it and select change drive letter and paths."  It should show the letter currently assigned (G I guess).  Click the button change.  To the right will be a drop of drive letters box.  Go ahead and select F and click on OK.  That should do it. If F is not available, then it is used by the system for something else.  Check disk management to see if you can find it.  If it is not, and is not available in the list, I'm afraid, you will not be able to change until find you what is using drive letter F and remove it, or change it to something else.

  I hope this helps.  If this isn't the case, after return and we will try to understand what is using F or why it is not available.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Workstation 9 - broken PXE boot - works with 8 workstations

  VMware Workstation 9 newly released, the PXE boot is broken. It works on the same machine with VMware Workstation 8.

  
  Virtual machine specifications:

  -Windows 7 and Windows 7 x 64

  -Bridged networking

  -2 1 processor cores

  I tried on different hardware, without Windows Firewall, but the PXE boot is broken when you use Workstation 9. Any thoughts as to why her behave this way?

  We are trying to perform a PXE boot and it gets everything stuck by sending requests for the services of pre-launch on the remote server, however, it seems that the return packets are not received. On 8 workstations, these are received and PXE boot works correctly.

  There is no AV installed in the host operating system.

  Wow, okay, just confirmed this seems to be a MAJOR bug in the work station 9, concerning ONLY to run 2 hearts or 2 CPUs. I tested with my cell phone would support all configurations (this is a quad core with hyperthreading). This applies in my case to Novell Zenworks Imaging, but can affect more.

  Results

  Config	PXE
  1 processor, 1 core	Success
  1 CPU, Core 2	In case of failure
  1 CPU Core 3	Success
  1 CPU, Core 4	Success
  1 CPU, Core 6	Success
  1 CPU, Core 8	Success
  2 CPU, 1 core	In case of failure
  2 CPU, Core 2	Success
  2 CPU, Core 3	Success
  2 CPU, Core 4	Success
  4 CPU, 1 core	Success
  4 CPU, Core 2	Success
  8 CPU, 1 core	Success

  Now here it gets crazy. My issue seems to be with the v11.2.0.0 of the Agent Novell PXE (Preboot Execution). It says "Sending queries to xxx.xxx.xxx.xxx" then he received never actually do anything to continue the boot process, but ANY other config except 2 CPU or 2 cores CPU works fine.

• running Linux rather than Windows as host

  Hello

  I'm trying to start learning of VMware and I wonder which version of the operating system, it is best to run it as a host for VM workstation? Inside of the workstation, I'll run 2 instances of ESXi machines so I'll try to save some resources with Linux. Don't you think it's just if I install Linux instead of Windows 7? I really save you 1 GB of RAM, or not? (theoretically for 64-bit Linux, it's 384-512 MB of RAM and Windows 7, it's nearly 2 GB of RAM)

  The bottom line is made the effort running Linux rather than Windows is worthing? Because it's a pain even with Linux.

  Thanks in advance for your advice!

  Catalin

  I think that you run your host operating system with what you are comfortable with.  My choice would be Windows 7 x 64.  ESXi running as a virtual machine in my computer would work fine, just follow a few best practices recommendations.

  Nested VMs running

  The VMware products and material assistance to virtualization (VT-x/AMD-V)

  Troubleshooting problems Intel VT - x

  http://KB.VMware.com/kb/1030283

  http://www.Vladan.fr/how-to-install-ESXi-4-1-inside-of-VMware-Workstation-7-1/

• Install CC Apps rather than the newer versions of the CC 2014?

  Hello

  On my main workstation, I always work with the CC versions. Now, I would like to install on my MacBook, but I can not understand how to download the CC Apps rather than versions CC 2014.

  Thank you

  Pascal

  Pascal please see previous section installation Version and update the apps - https://helpx.adobe.com/creative-cloud/help/install-apps.html for more information on how to install older versions of Adobe Creative Software included with your membership.

• Install ESXi 4.1 see physical disks rather than raid 1

  Data sheet:

  -CPU Intel X 3450

  -Intel S3420GPLC motherboard

  -2 X Seagate ST3750528AS 750 GB (Raid 1)

  I try to install esxi 4.1 on above using the embedded raid controller.

  According to this post (http://communities.vmware.com/message/1393463#1393463) I set the Commission to use "Intel matrix Raid" as the type of controller.  Who is the one who supports Raid 5 so that I would use anyway.

  The problem is when I choose the disc to install VMware shows two physical drives rather than for the raid set.  Installation at one of these BRAKES the raid (not surprising), who then proceeds to try to rebuild his car, but never quite get there.

  Gparted and Win 2008 as bios only list the raid set.

  The Board is listed in the list of compatibility with the following notes:

  1. State power supply not supplied.

  2. total count and status not provided all of the thermal system and temperature sensors.

  3. when the State of system fan not intended to indicate that a fan has been removed.

  4 Intel 82578 DM Gigabit Network Connection not supported.

  Anyone has any advice on what I could try?

  As a general rule, the RAID controllers on board are NOT material (with BBWC) RAID controllers... Therefore, you will not see a picture that you build on them as a single volume, but as their readers (lone) component... ESX/ESXi requires RAID controllers for drives configured in a table in order to present in a table...

  What HCL did the jury on (do not see on the VMware HCL)?

  In addition, given that the NETWORK card is not supported, you need to install a NETWORK card that is supported before you will be able to fully install ESX/ESXi on the system...

  If you really need to have readers in a table (never a bad idea to use RAID 1 or 10), then you will need get a RAID controller that is on the VMware HCL as supported (for installing ESX/ESXi on) and then move on... I'd go with a controller using the LSI MegaRAID chipset (or this LSI controller directly). As you connect SATA drives to the system, you will want to get the RAID controller that is listed as SATA/SAS-RAID, so that it will work properly/entirely with the SATA (and SAS) readers... Newegg has the LSI MegaRAID cards manage up to four drives internally (and are on the VMware HCL) for not much money (~ $300 each)...

  As many people on these boards will tell you, material compatibility is CRITICAL for ESX/ESXi... VMware publishes and updates constantly, their HCL for a reason... If it's on, then it is supported in the configuration also listed... If something is not listed for a certain version/version, then you can pretty much bet that it is not supported and will not work. If you want a stable host and environment, you will have to pay special attention to the HCL in deciding the selection of material...

  VMware VCP4

  Review the allocation of points for "useful" or "right" answers.

• Can I actually delete messages rather than having that they are sent to the Recycle Bin?

  I want to know how I can delete messages rather than the envoys in a junk folder or recycle bin and then delete them from there. I have several filters set up and send them to separate subfolders. But of course, when I look at these and remove them, they go in the trash. Then I can actually delete them so that they're gone, that's what I think delete would do in the first place. Is it possible to do so, to delete messages without moving them to the trash and then remove them from there? It is important that I don't miss any messages, I still sometimes do, but I'll have 50 posts or more per day that are trash. Most of them pass through my filters, but if I do not have a daily interview with a bunch of garbage I'd meet a real nightmare.
  Surely people have requested this, and I've seen some with answers like "it's the way it was designed. Can it be done?

  Thank you, if there is a useful link that send.

  Hold down the SHIFT key when you press DELETE.

• How can I close a tab that has locked up, rather than farm the whole browser to be insensitive?

  I have a bad habit of having several tabs open. If I click on a link that translates the whole browser becomes unresponsive, how do I close the tab offending rather than having to close the entire browser and losing all my tabs?

  It is not a bad habit, it's normal.

  Unfortunately, there is currently no way to 'kill' a single tab without picking up Firefox.

  A few times a week I get "not responding" when I exceed the amount of memory Firefox can use. Usually about 60-90 seconds, I can close Firefox by using the menu, either:

  • "3-bar" menu button > button "power".
  • (menu bar) File > Exit
  • These same keys in order:Alt f x

  Freezes caused by other reasons could not out, in which case you get stuck. Prevention is the best cure.

  This support article covers some common reasons for freezes: Firefox crashes or does not - how to fix.

  Since the Flash plugin can also cause this problem and it is used everywhere around the web, I suggest the following to minimize potential problems with Flash in your troubleshooting:

  (1) to avoid unnecessary pain on the sites where the Flash is not really essential, try to set the Flash on Click-to-Play (Ask 'activation'). This will delay the Flash start on a page, until you approve.

  To set 'Ask to activate', open the page modules using either:

  • CTRL + SHIFT + a
  • "3-bar" menu button (or tools) > Add-ons

  In the left column, click on Plugins. Search 'Shockwave Flash' and always change 'enable' to 'ask to activate '.

  With this setting, when you visit a site that wants to use the Flash, you should see a notification icon in the address bar and usually (but not always) one of the following values: a link in a gray rectangle dark in the page or an information bar sliding between the toolbar and in the page area.

  The plugin notification in the address bar icon usually resembles a little Lego block, dark gray. (If it is red, Flash must update.)

  The delay in the activation of Flash can help distinguish between the problems caused on the initial page load, put in folds and script activation vs Flash/loading bar.

  If you see a good reason to use Flash, and the site looks trustworthy, you can go ahead and click on the notification icon in the address bar to allow Flash. You can trust the site for the time being or permanently.

  But some pages use Flash only for tracking or play ads, so if you do not see an immediate need for Flash, feel free to ignore the notification! He will just stand here in case you want to use it later.

  (2) a common cause of errors in script does not work in Windows Vista and later is the feature of mode of the Flash player plugin. This feature has the security benefits, but it seems to have serious compatibility problems on some systems. You can disable it using the page modules. Either:

  • CTRL + SHIFT + a
  • "3-bar" menu button (or tools) > Add-ons

  In the left column, click on Plugins. On the right side, find 'Shockwave Flash' and click on the link for more. Then uncheck the box for "Enable Adobe Flash protected mode" and try it for a day to see if that helps you.

• How can I set my homepage to a new request tab rather than "suggested" or "white"?

  With the latest updates of Firefox, the tabs have changed. In the past, I was able to have a new tab open to my homepage (google), but seem to now have sites either empty or suggested/frequently visited. Although this sounds like a minor problem, he build a movement additional/click/selection and is a bit of your time and irritating - most of my use of the internet has its source in a research rather than a favorite site.
  Someone knows a way back?
  Thank you very much.
  R

  The preference of browser.newtab.url has been added to Firefox 13. Over the years, he was repeatedly attacked by malware. From Firefox 41, the preference can be changed using an interface programming or, in simpler terms, an extension.

  For example, you can use this extension:

  https://addons.Mozilla.org/firefox/addon/new-tab-override/

  After installing the extension, you must use the Options page to set the new desired tab page (instead of use subject: config).

  Open the page modules using either:

  • CTRL + SHIFT + a (Mac: Cmd + shift + a)
  • "3-bar" menu button (or tools) > Add-ons

  In the left column, click Extensions. Then on the side right, find the new tab override and click the Options button. (See first screenshot attached).

  Depending on the size of your screen, you may need to scroll down to enter the address in the form. (See second screenshot attached). For example:

  • (Default) page thumbnails = > subject: newtab
  • Blank tab = > subject: empty
  • Built-in Firefox homepage = > topic: welcome
  • Any other page = > full URL of the page

  Then tab or click this form field and you can test using Ctrl + t.

  Success?

  Once you have set it as you wish, you can close the Add-ons page (or use the back button to return to the list of Extensions of this Options page).

• I can rearrange the email component and seen to be side by side rather than stacked?

  I can rearrange the email component and seen to be side by side rather than stacked?

  What does that mean?

• How can I force Firefox to access an external web site rather than the site corresponding to the cache on my computer?

  A web site that I regularly access using Firefox has been updated in the last 24 hours. I make Firefox to access the external site updates rather than site updates apparently stored on my memory cache?

  You can reload webpages and ignore the cache to refresh potentially stale or corrupt.

  • Hold down the SHIFT key and click the Reload button
  • Press 'Ctrl + F5' or 'Ctrl + Shift + R' (Windows, Linux)
  • Press 'Command + shift + R' (Mac)