WRT1900AC - brick? having firmware new flash hard

Then my friend tried to put OpenWRT on his WRT1900ac and he thinks that he he bricked. Of course, I'm done with the broken router.

I have two computers available to try to solve this problem, an iMac with El Capitan and a Thinkpad Windows 10. I have a USB-> TTL series adapter and I disassembled the router to access the terminals of series, I tried flashing the new firmware on TFTP but my utility doesn't even know something is connected to the COM (Yes, I have the right drivers)

Here's what it does. I turn on the router, and after a few seconds, the power LED flashes. So, if I have an ethernet cable plugged in, the corresponding led lights up. So many Windows, I put my network settings to force 192.168.1.1 and ping 192.168.1.1 succeeds... but he also managed when I turn off the router. (Yes I turned off all other network connections). When the router is turned on and I open a browser at this address, I get a blank page. The gui of Linksys TFTP cannot connect at all. (I get a message like "router has failed")

From my Mac, it's sort of a different story. I can't find a USB-> COM at all driver, so serial interface is released. But I can manually set my network to 192.168.1.1, ping it when the router is off, don't get no response (good) - I turn on the router, ping, come back successfully 64 bytes (good). I can open 192.168.1.1 in a browser and get the page of "it works!" But if I try to Flash a firmware using the integrated terminal TFTP protocol, I get a time out (as follows...)

tftp 192.168.1.1
tftp> binary
tftp> timeout 120
tftp> put firmware.img
Transfer timed out.

So I am all out of ideas, are too recent for this problem in my operating system? I should go out by the live usb Linux Mint?

Use your computer for Windows 10, it will be easier to update the firmware.

  1. Install the version x 32 or x 64 http://www.jounin.net/tftpd32_download.html tftpd
  2. Then install Tera term https://en.osdn.jp/projects/ttssh2/releases/
  3. Once installed, Tera Term configure it to use the USB port to the port com TTL with the parameters 115200,8, no, 1 no
  4. Power on the WRT1900AC; You should see boot you after the release of text in Tera term; If you do not see the output, it is most likely that you have the RX and TX inverse series. Don't proceed to the next step until you confirm the serial communication is increasing.
  5. Press a key in Tera term during the second pause 5 pause of submarine appears. That you will get a u-boot prompt. Attention here because you can do a hard easy work if you run the wrong commands.
  6. Configure the network card in your computer to the IP 192.168.1.254 netmask 255.255.255.0, no gateway and no DNS.
  7. Connect to the computer via an Ethernet cable to a LAN of WRT1900AC port.
  8. The u-boot prompt, run "ping 192.168.1.254"; If the result is 'living' submarine can connect to the computer.
  9. Make sure your firmware is in the current directory of the tftp server and the tftp server is listening on 192.168.1.254.
  10. To the submarine command prompt run "setenv firmware_name my-firmware - filename.bin" for the WRT1900AC V1 or "setenv firmwareName my-firmware - filename.bin" for the WRT1900AC\ACS\V2 or WRT1200AC
  11. The u-boot prompt, run "run update_both_images" wait for the command to complete.
  12. Then run "reset" or the router power cycle

To display the u-boot firmware load vars courses run the below to the u-boot prompt:

  1. print Ipserver
  2. IPAddr impression
  3. firmware_name printing or printing firmwareName

Tags: Linksys Routers

Similar Questions

  • I propose all the photos on a new external hard drive.  Now, all records have a question mark in them.  How can I find all THE PICTURES at once instead of having to find each photo. I have about 30 000 photos. In Mac Help. LR5

    I've implemented a new external hard drive and Im trying to redirect LR to the new hard drive. I have over 30,000 photos and Im trying to see if there is a way to pictures located without having to go through each folder at a time

    http://www.computer-darkroom.com/lr2_find_folder/find-folder.htm

    See Figure 4

  • New drive HARD & OS errors-> HP 8000 Elite Small Form Factor PC

    New drive HARD & OS errors---> HP 8000 Elite Small Form Factor PC

    Can not install Win XP on another hard drive

    I work with a...
    HP Compaq 8000 Elite Small Form Factor PC

    Original SATA HDD is loaded with Windows 7 Pro.

    In order to install a program using this PC as a digital video recorder
    I installed the video capture PCI card and related software. I had problems
    associated with software and Windows 7.

    I know that the software works with Windows XP.
    Do not want to remove the original HDD, I tried my win7
    to replace the HARD drive and do a clean install of XP.

    I get the same error during the installation of the OS.  I tried different
    SATA and different XP install disks.

    The error I get is shown in this photo.

    Original HP HARD drive is a Hitachi 160 GB

    I tried 2 known to be good SATA drives.
    Seagate 500GB
    WD 80 GB

    I checked the bios settings and even revenue tio rear BIOS
    default settings.

    I get this error even with everything I tried to do.

    This happens during the OS install just after or during the process of the installation of temporary files are current

    written to the HD.

    When I re - install the original HD loaded with Win7, everything works as it
    expected.

    Any ideas on what] s going on here?

    Hello:

    The problem is that you must incorporate the necessary sata ahci drivers for windows XP to see the hard drive.

    Has Windows 7 and XP is too old an operating system to make them.

    Read the info at the link below, section of Intel and then read the downloadable PDF document for instructions on how to integrate all the drivers.

    http://h30434.www3.HP.com/T5/notebook-operating-systems-and-software/SATA-drivers-for-XP-solution-on-0x0000007B-BSOD/m-p/114120#M17758

    The only other way to install XP on this model is to go into the bios, the storage section and change the setting of sata ahci to ide emulation, save the setting here and once again, when you go out.

    The problem is that if you do this, you cannot change the setting for the preferred setting of DCIS, unless you know how to install the correct ahci sata driver after installing XP from the controller.  If you try to just change the setting back on ahci without having to install the controller driver, the PC does not start upward.

    Try "slipstreaming" the drivers first and if you can't swing, install XP in IDE mode and I'll help you get the drivers installed, so you can change the BIOS to ahci setting.

  • I installed a hard drive 500 secondary gig, after re-booting the properties for the new drive hard only show 48.8 GB are available.

    I installed a hard drive 500 secondary gig, after re-booting the properties for the new drive hard only show 48.8 GB are available. where is the rest of the memory?  Its not partitioned to another eather drive

    original title: hard drive problems

    (1) what does your BIOS the drive size?

    ============================================================

    2) disk hard test - find your make and model:
    Speccy - computer/system information in detail
    (More detailed look at your memory and CPU)
    OS, CPU, RAM, card, graphics, hard drive, optical drive
    Audio, peripherals, network.
    Note: Option RAM indicates number of slots, DRAM Timing.
    Works your memory speed (frequency). The nominal frequency of your memory.
    http://www.Piriform.com/Speccy

    Test your player - CD Bootable:
    Ranging from 5 to 20% (depending on the manufacturing) new hard disks are defective. Test your drive with the factory utility. If you have a new hard drive Seagate the very next thing would be to download Seagate Seatools (bootable CD) and check bad sectors:
    http://www.Seagate.com/WW/v/index.jsp?locale=en-us&name=SeaTools&vgnextoid=720bd20cacdec010VgnVCM100000dd04090aRCRD

    For Western Digital readers to download the .iso from WdDiag file: http://support.wdc.com/product/download.asp?groupid=611&sid=30&lang=en

    Samsung Estool: http://www.samsung.com/global/business/hdd/support/utilities/ES_Tool.html
    Samsung Disk Manager software: http://www.samsung.com/Products/HardDiskDrive/utilities/shdiag.htm
    Hitachi Drive Fitness Test Software: http://www.hgst.com/hdd/support/download.htm#DFT
    Diagnostic tool available for use by customers who feel their Toshiba brand Fujitsu hard drive:
    http://SDD.Toshiba.com/main.aspx?path=ServicesandSupport/WarrantySupport/SoftwareUtilities
    Notice of suport Fujitsu disk utility: http://www.fujitsu.com/us/services/computing/storage/hdd/
    Toshiba CD bootable: (BACK Diagnostic Tool version 7.0 for IDE/ATA/SATA hard disks)
    http://SDD.Toshiba.com/main.aspx?path=ServicesSupport/FujitsuDrivesUSandCanada/SoftwareUtilities#diagnostic

    ================================================================

    (3) HD Tune:
    Provides information of the car and has an option (tab scan error) to test your drive.
    http://www.hdtune.com/

    SpeedFan:
    Monitors internal temperatures and has a function of analysis health online (SMART tab) for hard disks drive.
    It displays your drives model number and compares your drive with other discs of the same brand and model.
    http://www.almico.com/SpeedFan.php

    -Partition management utilities-

    Partition Wizard Home Edition:
    http://www.partitionwizard.com/free-partition-manager.html
    Note: There is also a CD bootable or versions of the bootable Flash drive:
    CD: http://www.partitionwizard.com/partition-wizard-bootable-cd.html
    Flash player: http://www.partitionwizard.com/bootable-flash-drive.html
    Among the features and functions: create partition, Delete partition, format partition,.
    A partition resize, move partitions, Partition recovery after an accidental deletion,
    Convert the partition, partition Explore, Hide partition,
    Change the drive letter, a partition active Set, Explorer (content display) of the partition.
    Note: To complete any task use the "Pending Operations" box at the bottom left.

    Alternative to Partition Wizard (a bit easier to use, but Partition Wizard and EASUS have almost identical user interfaces)
    EASEUS Partition Master Home Edition (free):
    http://www.partition-tool.com/
    Partition software ALL-IN-ONE and the most convenient hard disk partition manager Kit
    Includes Partition Manager, Disk & Partition copy Wizard and Partition MBR and GUID partition GPT disk recovery Wizard (table) on Windows 2000, XP, Vista, Windows 7 and Windows Server 2000/2003/2008 (32-bit and 64-bit).
    It allows users to resize/move Partition, drive system extend, copy Disk & Partition, Partition merge, Split Partition, redistribute free space, convert dynamic disk, Partition Recovery and much more.

    J W Stuart: http://www.pagestart.com

  • After copying a machine a host for another vspehere vsphere virtual machine I can not load the VM machine upwards. Can't open the Flash "hard" or one of the disks disk that this depends on

    Here is the error msg I get from vsphere client.

    Cannot open the Flash '/vmfs/volumes/52120f68-3f09e8f0-affd-f01fafcf18af/w2k3SE-base-20101005/Windows w2k3.vmdk' or one of the disks disk that it depends on.

    The system cannot find the specified file

    VMware ESX can not find the virtual disk '/vmfs/volumes/52120f68-3f09e8f0-affd-f01fafcf18af/w2k3SE-base-20101005/Windows w2k3.vmdk '. Check that the path is valid and try again.

    I have ssh client due to vmware ESX.

    ls # vmfs/volumes/52120f68-3f09e8f0-conf-f01fafcf18af/apple

    564d73b4-7443-6b7f-9a70-cd355ad76d3b.vmem Windows XP Professional.vmx.0 Windows w2k3 - s004.vmdk Windows w2k3 - vmware - 16.log s009.vmdk

    Windows XP Professional - 24367b9b.hlog Windows XP Professional.vmxf Windows w2k3 - s005.vmdk Windows w2k3.vmdk vmware - 17.log

    Windows XP Professional.nvram Windows w2k3 - s001.vmdk Windows w2k3 - s006.vmdk hiding vmware - 18.log

    Windows XP Professional.vmsd Windows w2k3 - s002.vmdk Windows w2k3 - 14.log - vmware vmware - 19.log s007.vmdk

    Windows XP Professional.vmx Windows w2k3 - s003.vmdk Windows w2k3 - vmware - 15.log vmware.log s008.vmdk

    It seems that all the files are there. Except that there are some spaces.

    / vmfs/volumes/52120f68-3f09e8f0-AFFD-f01fafcf18af/Apple # cat "Windows w2k3.vmdk".

    # Disk DescriptorFile

    version = 1

    Encoding = "windows-1252".

    CID = 97c834c1

    parentCID = ffffffff

    isNativeSnapshot = 'no '.

    createType = "twoGbMaxExtentSparse.

    # Description of the measure

    RW 4192256 CLAIRSEMES "Windows w2k3 - s001.vmdk.

    RW 4192256 CLAIRSEMES "Windows w2k3 - s002.vmdk.

    RW 4192256 CLAIRSEMES "Windows w2k3 - s003.vmdk.

    RW 4192256 CLAIRSEMES "Windows w2k3 - s004.vmdk.

    RW 4192256 CLAIRSEMES "Windows w2k3 - s005.vmdk.

    RW 4192256 CLAIRSEMES "Windows w2k3 - s006.vmdk.

    RW 4192256 CLAIRSEMES "Windows w2k3 - s007.vmdk.

    RW 4192256 CLAIRSEMES "Windows w2k3 - s008.vmdk.

    RW 16384 SPARSE "Windows w2k3 - s009.vmdk.

    # The database disk

    #DDB

    ddb.virtualHWVersion = "7".

    DDB. UUID = "60 00 C2 91 86 bb a5 - 5 c bc 28 89 75 01 c9 b0 e1"

    DDB. Geometry.Cylinders = "16383.

    DDB. Geometry.Heads = "16".

    DDB. Geometry.sectors = "63".

    ddb.adapterType = 'ide '.

    ddb.toolsVersion = "8228.

    ddb.longContentID = "9d219dcc524591ac1095297d97c834c1".

    and here's a copy of the vmware.log file

    2014-08-14 T 19: 01:56.925Z | VMX | I120: DISKLIB-STRING: "/ vmfs/volumes/52120f68-3f09e8f0-conf-f01fafcf18af/apple/Windows w2k3.vmdk ': cannot open (the system cannot find the specified file).

    2014-08-14 T 19: 01:56.925Z | VMX | I120: DISKLIB-VMFS: ' / vmfs/volumes/52120f68-3f09e8f0-conf-f01fafcf18af/apple/Windows w2k3 - s001.vmdk ": closed.

    2014-08-14 T 19: 01:56.925Z | VMX | I120: DISKLIB-VMFS: ' / vmfs/volumes/52120f68-3f09e8f0-conf-f01fafcf18af/apple/Windows w2k3 - s002.vmdk ": closed.

    2014-08-14 T 19: 01:56.925Z | VMX | I120: DISKLIB-VMFS: ' / vmfs/volumes/52120f68-3f09e8f0-conf-f01fafcf18af/apple/Windows w2k3 - s003.vmdk ": closed.

    2014-08-14 T 19: 01:56.925Z | VMX | I120: DISKLIB-VMFS: ' / vmfs/volumes/52120f68-3f09e8f0-conf-f01fafcf18af/apple/Windows w2k3 - s004.vmdk ": closed.

    2014-08-14 T 19: 01:56.925Z | VMX | I120: DISKLIB-VMFS: ' / vmfs/volumes/52120f68-3f09e8f0-conf-f01fafcf18af/apple/Windows w2k3 - s005.vmdk ": closed.

    2014-08-14 T 19: 01:56.926Z | VMX | I120: DISKLIB-VMFS: ' / vmfs/volumes/52120f68-3f09e8f0-conf-f01fafcf18af/apple/Windows w2k3 - s006.vmdk ": closed.

    2014-08-14 T 19: 01:56.926Z | VMX | I120: DISKLIB-VMFS: ' / vmfs/volumes/52120f68-3f09e8f0-conf-f01fafcf18af/apple/Windows w2k3 - s007.vmdk ": closed.

    2014-08-14 T 19: 01:56.926Z | VMX | I120: DISKLIB-VMFS: ' / vmfs/volumes/52120f68-3f09e8f0-conf-f01fafcf18af/apple/Windows w2k3 - s008.vmdk ": closed.

    2014-08-14 T 19: 01:56.926Z | VMX | I120: DISKLIB-VMFS: ' / vmfs/volumes/52120f68-3f09e8f0-conf-f01fafcf18af/apple/Windows w2k3 - s009.vmdk ": closed.

    2014-08-14 T 19: 01:56.926Z | VMX | I120: DISKLIB-LIB: can't open ' / vmfs/volumes/52120f68-3f09e8f0-conf-f01fafcf18af/apple/Windows w2k3.vmdk' with flags 0xa, the system cannot find the specified file (25).

    2014-08-14 T 19: 01:56.926Z | VMX | I120: Msg_Post: error

    2014-08-14 T 19: 01:56.926Z | VMX | I120: [msg.disk.fileNotFound] VMware ESX can not find the virtual disk "/ vmfs/volumes/52120f68-3f09e8f0-conf-f01fafcf18af/apple/Windows w2k3.vmdk» Check that the path is valid and try again.

    2014-08-14 T 19: 01:56.926Z | VMX | I120: [msg.disklib.FILENOTFOUND] the system cannot find the specified file

    2014-08-14 T 19: 01:56.926Z | VMX | I120: [msg.disk.noBackEnd] cannot open disk ' / vmfs/volumes/52120f68-3f09e8f0-conf-f01fafcf18af/apple/Windows w2k3.vmdk' or one of the snapshot disks it depends on.

    2014-08-14 T 19: 01:56.926Z | VMX | I120: ----------------------------------------

    2014-08-14 T 19: 01:56.939Z | VMX | I120: DISC: discs of opening had 24 ms.

    2014-08-14 T 19: 01:56.939Z | VMX | I120: Module DiskEarly market failed.

    2014-08-14 T 19: 01:56.939Z | VMX | I120: VMX_PowerOn: ModuleTable_PowerOn = 0

    2014-08-14 T 19: 01:56.942Z | VMX | I120: WORKER: asyncOps = 1 maxActiveOps = 1 maxPending = 0 maxCompleted = 0

    2014-08-14 T 19: 01:56.950Z | VMX | I120: Vix: [12787513 mainDispatch.c:3870]: VMAutomation_ReportPowerOpFinished: VarEtat = 1, newAppState = 1873, success = 1 additionalError = 0

    2014-08-14 T 19: 01:56.951Z | VMX | I120: Vix: [12787513 mainDispatch.c:3870]: VMAutomation_ReportPowerOpFinished: VarEtat = 0, newAppState = 1870, success = 1 additionalError = 0

    2014-08-14 T 19: 01:56.951Z | VMX | I120: Past vmx/execState/val of poweredOff

    2014-08-14 T 19: 01:56.951Z | VMX | I120: Vix: [12787513 mainDispatch.c:3870]: VMAutomation_ReportPowerOpFinished: VarEtat = 0, newAppState = 1870, success = 0 additionalError = 0

    2014-08-14 T 19: 01:56.951Z | VMX | I120: Vix: [12787513 mainDispatch.c:3909]: error VIX_E_FAIL in VMAutomation_ReportPowerOpFinished(): unknown error

    2014-08-14 T 19: 01:56.951Z | VMX | I120: Vix: [12787513 mainDispatch.c:3870]: VMAutomation_ReportPowerOpFinished: VarEtat = 0, newAppState = 1870, success = 1 additionalError = 0

    2014-08-14 T 19: 01:56.951Z | VMX | I120: Past vmx/execState/val of poweredOff

    2014-08-14 T 19: 01:56.952Z | VMX | I120: VMIOP: output

    2014-08-14 T 19: 01:56.956Z | VMX | I120: Vix: [12787513 mainDispatch.c:861]: VMAutomation_LateShutdown()

    2014-08-14 T 19: 01:56.956Z | VMX | I120: Vix: [12787513 mainDispatch.c:811]: VMAutomationCloseListenerSocket. Close the socket of the receiver.

    2014-08-14 T 19: 01:56.957Z | VMX | I120: VMX VMDB Flushing connections

    2014-08-14 T 19: 01:56.957Z | VMX | "I120: VmdbDbRemoveCnx: remove Cnx Db for ' / db/connection / #1 /"

    2014-08-14 T 19: 01:56.957Z | VMX | I120: VmdbCnxDisconnect: Disconnect: pipe closed for pub cnx ' / db/connection / #1 /' (0)

    2014-08-14 T 19: 01:56.961Z | VMX | I120: Exit VMX (0).

    2014-08-14 T 19: 01:56.961Z | VMX | I120: AIOMGR-S: o stat = 1 r = 3 w = 0 I = 0 br = 49152 bw = 0

    2014-08-14 T 19: 01:56.961Z | VMX | I120: OBJLIB-LIB: ObjLib cleaning done.

    2014-08-14 T 19: 01:56.961Z | VMX | W110: VMX has left the building: 0.

    Assuming that you have enough free disk space on the host ESXI 5.1 data store, I suggest you that you load the multiextent module as shown in the link, I posted and then clone the virtual disk using the vmkfstools command line utility.

    vmkfstools 'Windows w2k3.vmdk'-i 'clone.vmdk' slim-d - an ide

    vmkfstools EI 'Windows w2k3.vmdk' 'old.vmdk '.

    vmkfstools EI "clone.vmdk" "Windows w2k3.vmdk".

    The first line of the clones of the virtual disk in a virtual drive put in service end format, and the following two lines renaming virtual disks, so that you can delete the "old*.vmdk" files once the VM works as expected.

    Alternatively, you can also run the commands on the host ESXi 4.1 and then copy the new files hard again to avoid loading the multiextent module in the new host.

    André

  • Why force Adobe installs their new Flash drive when it is originally from the browsers play not video?

    Why force Adobe installs their new Flash drive on billions of computers when it is causing so many browsers only play video?

    I had installed the Flash Player 11.2.202.228 28/03/2012 and it worked very well, unlike some of the previous Flash players in several web browsers, so I chose NOT to install a new actors Flash that came after that, all based on experience.

    But last Friday, 22/06/2012, I received a new message to install Adobe Flash Player that came in my office for the new Flash Player v 11.3.300.262 and I chose NOT to install it for the reason I said above... and the look now at all the problems this new Flash player has caused for so many people.

    Now I see glancing at my Add-ons Manager in my Firefox browser, and in my program Panel of Windows 7 in the control panel that the stupid new Flash Player v 11.3.300.262 has been INSTALLED FORCE behind my back, even if I don't install certainly NOT it and I deleted the installation Panel when he came to my office on Friday.

    And now no videos or content Flash will not play in my Firefox browser! Good job Adobe!

    What is the Adobe problem?... why you require the software on our computers that obviously was not installed by the user, and then screw it to the top of our computers.

    How to explain something like that?

    Now, I have to troubleshoot it and try to install my old Flash Player.

    Why?

    Having click on classic view on the left side of the Control Panel window, which should show all of the icons and allow him to see the Flash Player icon.  The alternative is to type 'flash player' in the control panel search box which should be also.

    Note also that change the auto update to "notify me to install updates" will only delay the process of 30 days.  After 30 days, the update will be installed automatically.  You can completely disable this by changing it to "never check", but I would certainly recommend against that.

  • iBook Clamshell detects no no new internal hard drive

    I have an iBook Clamshell (M2453 PC, 300 MHz) and I just replaced the old 6 GB hard drive with a new hard drive 60 GB. The new drive is a regular 2.5 "IDE/PATA drive. I don't know the brand or the rpm of the road, because the seller provides various brands/rpm and I didn't check before installing. I'm guessing this is a Hitachi, Seagate, Fujitsu, etc. either 5400 or 7200 RPM. I don't think that is important, because the drive came in a clean condition and has been formatted. The problem is that when I try to install OS X 10.3 on the new drive hard, it is not detected at all. It does not appear on the screen "Select Destination", the startup disk, or disk utility. Disk utility shows only the OS X install CD, nothing else. I confirm that this isn't for lack of the CD, as I used it many times in the past to install OS 10.3 on other Macs. I tried to reset the NVRAM, PRAM, I even tried the PMU button under the screen, but nothing has worked. However, the old hard drive with OS 9.2 worked perfectly, and I've made sure to connect everything correctly when I replaced the drive, does this mean a new is simply defective, or there at - it another option to try to fix? I don't disassemble the laptop again, but if I have no choice I will do what I must. Thanks in advance.

    If disk utility is not able to detect the hard drive, it could indicate a problem with the drive, the hard drive cable or control circuits in the computer. Disk utility should see at least the reader as such, even if a volume is not displayed.

    As a first step, if you have access to a proper record of the Mac OS (9.x), you can test the configuration of disk utility instead (just to see if the hard drive can be detected at all). Also, disk utility on a PowerPC (https://wiki.ubuntu.com/PowerPCFAQ) to a proper Ubuntu CD version could possibly used for similar drive information research and test operations on your computer.

  • I don't have a 2nd computer.  Is it possible to migrate an external backup, and then on a new drive hard mac?

    I don't have a 2nd computer.  Is it possible to migrate an external backup, and then on a new drive hard mac?

    Use Time Machine or a clone to copy to the outside.

    Time Machine Basics

    Basics of Time Machine (2)

    Time Machine Basics (video)

    Time Machine FAQ

    First Time Machine backup

    Clone - Carbon Copy clone          (Often recommended because it has more features than others)

    Clone-data backup

    Clone-Deja Vu

    Clone - SuperDuper

    Clone - Synk

    Clone - 6 tested Applications Software

    Time Machine from the Clones and Archives

    Commonly used backup methods

  • New drive HARD and OS upgrade on Equium A210

    I want to install a new SATA hard drive more and also upgrade from Vista to Windows 7 is only a problem at all and that I can use a normal Windows 7 disc.

    Hello

    Generally avoid any problem with drive HARD and OS upgrade. If you want to have the exact answer please let us know what model of laptop you have.

  • How to replace a new drive hard satellite 1670cds

    How to replace a new drive hard satellite 1670cds
    do I have to remove the keyboard?
    wath is the GB limit

    Hi Theo,.

    HARD drive is mounted on your machine fest, and it is not easy to change. First you have to remove the keyboard, then view and top of page coverage too. If you want to do it yourself, be careful. If you do something wrong, it can be very expensive.

    It is not easy to say which is the limit of the HARD drive, but I'm sure you can use 10 GB with no problems. Try to contact the after-sales Service of Toshiba partner. Perhaps, they can give you specific information.

    Good bye

  • How can I make the best use of a new external hard drive and a new catalog full of photos just loaded into Photoshop elements 14 Organizer?

    How can I make the best use of a new external hard drive and a new catalog full of photos just loaded into Photoshop elements 14 Organizer?

    Keep all the files on external hard drive image?  Nothing else and no pictures on the desktop?

    Keep all image files both places?

    What is the best way to go through thousands of images in the Organizer to identify and place them in files?

    Once I've placed a file, I just leave it in the entire catalog or a way indicate to me that it has been sorted?

    As overwhelming, any tips/shortcuts/schemes, you can offer are welcome!

    As I only have the version of the EP, here is some info on the organiser:

    https://helpx.Adobe.com/Photoshop-elements/how-to/use-elements-Organizer.html

    Independent of how this feature works, you want to have your photos in one place and have a backup (second copy) somewhere else. All hard drives will not be successful at some point - some more early, some late - never trust to have your files in any safety devices if they are on a single disc. Once you have your sorted, it would be useful that you will organize/name/tag new photos immediately if the task is relatively short and simple. I copy my photos on my internal hard drive for my camera, take a quick look with preview to see who needs some changes and then decide where to put them - either drop them immediately after naming them or bring in an editing application and then file them away.

  • Transfer iTunes library to a new external hard drive.

    I did a few years back, but as for the double control procedure to ensure I would correctly.

    My iTunes music library is stored on an external hard drive. It's almost to capacity, if I want to transfer the files from current music on an external hard drive more.

    I don't want to "lose" my preferences iTunes, settings etc that I have playlists, ratings and other data.

    I understand that the first thing is physical copy music files to the new external hard drive.

    What is the procedure to then "point" to the new hard drive.

    Thank you.

    Copy the iTunes folder whole, not only the media, on the external drive, launch iTunes with the Option key, choose this library and keep a backup on a different drive of it.

    (138343)

  • Replace T420s with a new SSD HARD drive

    Hello

    I wonderd if it is possible to replace with a new SSD HARD drive, while putting the HARD drive in the Bay of Ultra-slot.

    And if so, what SSD model should I buy, and how do I transfer the operating system and the data for the SSD?

    This SSD model will be compatible?

    Corsair neutron Series 120 GB SSD Sata III MLC 2.5 inches Retail

    Thank you very much

    Guy

    Yes, what you are proposing is quite feasible. You will need an adapter Ultabay to organize your HARD drive in the Ultrabay housing on your system. These are available from Lenovo, but are relatively expensive. You can get a much less expensive (~ $ 10) a compatible version on eBay. It is not as well finished as the real issue, but it works well.

    The best way to transfer everything on your SSD is "clone" of your HARD disk using a software as Acronis True Image. If your current HARD drive is made by Western Digital or Seagate you can get a free copy of Acronis on their Web site. Put the SSD in the SATA drive Bay and the HARD disk in the UtlraBay. Set the T520 to start from the Ultrabay, install/run Acronis here and make a clone for the SSD. Then boot from the SSD and you'll be all set.

    With respect to the SSD, many people here have had good success with Crucial M4, 520 Intel and Samsung 830. I guess that Corsair works perfectly as well, but I didn't know all messages from people here who have done so.

    Before ordering a SSD confirm if the HARD drive is 7 mm or 9.5 mm thick. Then order the same thickness SSD. This way, you will be able to use the metal rails caddy and rubber who now hold your HARD drive to contain the SSD.

  • I recently bought a new larger hard drive for my XPS M140 / 630 M.

    I recently bought a new larger hard drive for my XPS M140 / 630 M. I am unable to get windows XP to complete the installation on the new drive. How can I get windows install completely? Thank you!

    Hi A.P.ZG,

    Thanks for posting in the Microsoft Community.

    Since you are facing a problem to install Windows XP on the new drive, it would be useful if you can answer this question to help you further.

    You receive error codes or messages during the installation fails?

    You can read the article and check if it helps to solve the problem.

    How to partition and format a drive hard using the Windows XP Setup program

    Note: If the disc contains all the data, make sure that you back up all your important data before you continue.

    You can also disconnect all the external devices connected to your system (except the keyboard and mouse) and check if it helps.

    If you need further assistance, please answer and we will be happy to help you.

  • When I typed my name on my new doctor hard it doesn't have to enter the [s] in my last. How can I fix it name cela in all the app, on my sys drive.and. ?

    http://answers.Microsoft.com/en-us/search/search?Searchwhen I typed my name on my
    new drive hard o.sit, impossible to copy everything that the letters of my last. How do I fix this?

    Hello

    Try the steps suggested in the link below: http://answers.microsoft.com/en-us/windows/forum/windows_xp-desktop/changed-account-name-but-cant-change-logon-name/e90f81a9-0e5e-4511-b2f9-e286e05589e4

Maybe you are looking for