WRT1900AC seems to limit myself to 10 Mbps when the gateway computer gets directly 100 Mbps

Similar Questions

• My Windows Vista download updates and seem to install but do not configure when the computer restarts. Clues about the problem?

  This has happened since April 12, but I'm just now "getting it." no error messages or numbers.   I saw something on NVIDIAnForce 10/100 Mbps Ethernet problem in another context?

  Hi donorann,

  ·         Did you do changes on the computer before the show?

  ·         Updates (KB numbers) you are trying to install?

  ·         The updates are installed successfully?

  View the history in Windows Update in Control Panel window, or go to installed updates:

  Open installed updates by clicking the Start button, click Control Panel, click programs, and then under programs and features, click view installed updates.

  Follow the steps in the article.

  Error: Failed to setup of the Windows updates. Restoration of the changes. Do not turn off your computer when you try to install Windows updates

  Note: You must take the backup of the data before performing any installation of windows.

  For reference:

  You cannot install some programs or updates

  Understand the automatic Windows Update

• Satellite P30 seems to completely charge the battery only when the unit is turned off completely

  Hi, I have my Toshiba Satellite p30 and only works on battery. This unit operate on sector or only on the battery as after the period of time go down the warning, then closes. The orange light fades in and out, but seems that it will only fully charge when the unit is turned off completely.

  I only just received this unit so bit of a novice.

  MASH

  Hello

  normally, the battery should always charge until it is full when the power is connected.
  If you have an orange light flashes, it means that something is wrong. Maybe your battery is faulty or something else. This should be checked by a technician.

  Good bye

• LIMIT OF THE SERVER COMPUTER (WINDOWS 7 PRO SERVICE PACK 1)

  Hello

  Nice day.

  I have a server with window 7 pro service pack 1 computer. AFAIK, there are up to 20 eligible device to connect to the shared folder.

  However they allow up to 11 computer to access the shared folder on the server computer.

  When the 12 computer tried to access the shared folder on the server computer, it pop of a statement that he said already reach the maximum of the relationship.

  I confuse myself because the connection will not exceed 20 connection and he just stuck the next connection to the folder shared on the server computer.

  Please advise us of the solutions to this problem.

  Thank you and best regards,

  Tony

  Beyond the declaration is the statement you mention?

  However now only 11 device (computer) which connect to the shared folder. So that means that only 11 connection. When 2 or 3 more connections to the folder shared, he pop of a declaration that he State already reach the maximum of the relationship.

  It comes to education, to which I was referring.

  I don't know why you should be unable to do more than 11 connections. In this case, I use Google to search, type the exact error message in the search box. Chances are that someone else has had the same problem and found a solution.

• My MBP 2012 gets very hot on the bottom on occasion.   He also seems to be slow at times especially at the beginning of the session.  I ran a check and here's what I got back 11/4HDD/40000000 SATA (0,0).  Any help on what's going on?

  My MBP 2012 gets very hot on the bottom on occasion.   He also seems to be slow at times especially at the beginning of the session.  I ran a check and here's what I got back 11/4HDD/40000000 SATA (0,0).  Any help on what's going on?

  a quick search brings us to recent threads = the essential so that "SSD or related connection.

  https://www.Google.com/search?q=4HDD%2F11%2F40000000+SATA+%280%2C0%29+site%3Aapple.com& ie = utf - 8 & oe = utf - 8 #q = 4HDD/11/40000...

  Mac Laptops: Apple Hardware Test may report alert 'HDD' - Apple Support

  ...

  ... If the message in addition to the other problems related to the drive to solid state (SSD) or Flash storage disk, go to an Apple Retail Store or contact Apple's Service Providerwith the computer.

  ...

• I Net Nanny parental control installed on my pc and limit myself to give my child access to his Hotmail account to check emails.

  original title: hotmail servers

  Hello

  I Net Nanny parental control installed on my pc and limit myself to give my child access to his Hotmail account to check emails.

  There is an option in Net Nanny (NN) to allow only Web sites, but I have trouble understanding exactly what servers Hotmail uses to run.

  Furthermore, I feel that some server addresses change over time. Is this true? If this is not the case, can you let me know which servers should I use to get a permanent solution for the NN filter.

  Thank you

  Neville

  After all the Hotmail issues in the appropriate forum found here:
  http://windowslivehelp.com/

• What are the causes the limit 2 Gig Ram in m1170n Media Center computer?

  What are the causes the limit 2 Gig Ram in m1170n Media Center computer? It can be corrected? Makes for a much slower PC than it could be. I can update only 1 3/4 Gig and yet it can begin.  I tried the bios update that is available on this site, but it doesn't seem to change anything. It would be much nicer I could date within the limits of the operating system. 4 GB. Don't know what I'll use this 4 PC yet, but this could be the deciding factor.

  Here are the specifications of your HP Media Center m1170n desktop computer and its card mother PTGD1-(Puffer). Based on the specifications, this model has a maximum HP approved limit memory 4 GB (4 x 1 GB = 4 GB). The problem you are experiencing is perhaps due to incorrect memory modules, modules of memory defective or damaged, defective or damaged memorty slots or a very defective or damaged motherboard.

  Run the available at startup BIOS Diagnostics or download "memtest86" and create a bootable media. Then, run the test on each module individually, in the same housing. If all modules pass, rerun the test... this time by adding an additional module... Repeat until all slots are filled and all modules of memory are used.

  Please post back with your results.

  Please click the White Star of KUDOS to show your appreciation

• My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  Hello brooksm549,
  Thank you for using communities of Apple Support.

  I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

  On the use of the battery on your iPhone, iPad and iPod touch

  When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

  Maximize the life of the battery and battery life

  Best regards.

• I reinstalled iTunes for windows and downloaded two albums purchased on the iTunes store. Both albums have digital booklet in it but it seems that it has not downloaded. In the store, it seems certain. How should I download them?

  I reinstalled iTunes for windows and downloaded two albums purchased on the iTunes store. Both albums have digital booklet in it but it seems that it has not downloaded. In the store, it seems certain. How should I download them?

  Try iTunes Store > Quick links > purchase > music > not on my computer.

  If they do not show here, then visit https://reportaproblem.apple.com/

  TT2

• Firefox seems to have recently developed seemingly random usually do not remember bookmarks, particularly when the pc does not stop correctly. Thank you

  Firefox seems to have recently developed seemingly random usually do not remember bookmarks, particularly when the pc does not stop correctly. Thank you

  If Firefox detects that the places.sqlite database is corrupted then Firefox can create a new database file and import bookmarks from a JSON backup that does not contain the most recent bookmarks (a new JSON backup is created when you run Firefox for the first time on a day), then you may lose the bookmarks in such a case.

  You can check for problems with the database places.sqlite file in the Firefox profile folder.

  • http://KB.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox
  • https://support.Mozilla.org/KB/bookmarks+not+saved#w_fix-the-bookmarks-file

• You seem to have lost my iTunes library. The only albums I can find are those recently added

  You seem to have lost my iTunes library. The only available albums are those recently added.

  Turingtest2 CSA user help document: empty/corrupted iTunes after upgrade/crash library - https://discussions.apple.com/docs/DOC-6561

  If you do not see your content after updating to iTunes - https://support.apple.com/kb/HT203225

• I have a problem when I want to print an email page.it shows me an error that seems to come from a program that blocks the appearance windows.thos do sais.what do?

  Question
  I have a problem when I want to print an email page.it shows me an error that seems to come from a program that blocks the emerged Windows.ce do sais.what do? Edit

  Can you check this problem on Firefox 9?

  • getfirefox.com

• I've recently updated to Firefox 8 and since I did, I can't seem to open. Whenever I click on the icon on my desktop to open it, it crashes. What can I do to fix this?

  I've recently updated to Firefox 8 and since I did, I can't seem to open. Whenever I click on the icon on my desktop to open it, it crashes. I tried all the steps in the Firefox crashes article, and I can't understand what is wrong. How can I fix?

  Seems a common problem is Roboform and update to version 7.6.2 arranges.

• Siri doesn't seem to work, he won't answer when I hold the home button?

  Siri doesn't seem to work, he won't answer when I hold the home button?

  Have you checked to see if the settings > General > Siri is on?

• After the last update of the operating system and iMovie it seems I can't create a movie in the PAL standard. Can anyone help?

  After the last update of the operating system and iMovie it seems I can't create a movie in the PAL standard. Can anyone help?

  NTSC and PAL are analog standards and don't apply to the share or export settings in iMovie.

  It creates the same FPS and dimensions as your source file.

  What you trying to create?