XPS M1710 and MIDI?

Similar Questions

• XPS M1710 - Audio hardware problem

  I have a XPS M1710, probably close to 10 years. It has been impeccable in the performance over the years. However, one day my audio just stopped working. There a (!) in Device Manager, next to my card its SigmaTel High Definition Audio CODEC. When I go to properties it says the following.

  I am running Windows XP by the way...

  "State of the device.

  Windows has properly loaded this hardware device driver but cannot very well the hardware device (Code 41)"

  I decided to buy a new motherboard and recently installed new motherboard and I have the same exact error.

  I know that this laptop is super old, but that doesn't make any sense to me why the audio is always a failure. I'm going to uninstall the new motherboard and make sure that all connections seem to be good.

  Any other advice? A dead speaker at risk of this or any other material?

  Thank you

  Hello. A faulty speaker would not cause the error message. You could get the codec failed if it failed both the MB origin and replacement. You can test the codec running audio Dell 32-bit diagnostic tests. If you are testing is no longer, and then follow the instructions here to run the external media.

  If the audio tests pass then it's a software problem. It's probably too late to try the Windows system restore, so I would try to re - install the audio driver according to the normal order of the facility would be used after a new OS:

  1. install the Notebook System Software and restart.

  2 install the Intel chipset driver and restart.

  3 reinstall the driver Sigmatel.

  If still no sound but its past tests, then you should get audio back after the next time you perform a system recovery.

• Internal network card is cut off when I remove my XPS M1710 the docking station

  Hello

  I have a xps M1710 laptop. I normally use a docking station and the internal network card works fine when the laptop is in the docking station. But now when I remove the laptop from the docking station for the network adapter is disconnected.

  I know that it stops when the battery mode to save energy, but it is always closed when I connect to a power supply for laptop. I tried the plug before you turn on the computer and it does make a difference.

  It's not happened before and I have to go to the internet on my laptop earlier, when not to use the docking station.

  Any ideas on how to solve this problem?

  
  

• Update for the Dell XPS M1710 HDD issues

  Hey guys. Just a beginner on these forums since ive ever need a hand with my laptop. And I looked on the forums and couldn't find anything specific to my problem. So I have a XPS M1710 with a 100 GB hard drive at 7200 RPM, under Vista, and I would like to upgrade, especially for a 320 GB 7200 rpm or 200 7200 RPM. I also have a 320 GB external hard drive. First of all, what are the steps I should take to do upgrade, im also really confused on the whole "image" stuff Second, how can I find out what kind of hard drive of my laptop is compatible with? Finally I live in Australia and the site of Dell Aussie exclusively from a like 1 hard disk, so doesn't Dell ship the hard drive of the America to the Australia?

  
  

• No way to prevent "the AC power adapter type cannot be determined" message on XPS M1710? (AC adapter is properly plugged)

  Often, I get the following message between the screens "Dell" and "Windows", when that I start my XPS M1710 when plugged:

  Unable to determine the type of AC power adapter.  The system can start only with a 130 W power adapter or more.  Hit the F1 key to shutdown.  To resolve this problem, try to reconnect the AC adapter.

  This message occurs when the AC adapter is inserted correctly and completely, and that's the Dell adapter supplied with my notebook.  Is there anything I can do (possibly a registry hack) to force the computer to start instead of this message?  Once it gives me this message and I have to press F1 to close it, it takes an extremely long time to go to the "Dell" screen on the chest which follows (1 minute or two).  My battery hold so little cost when that happens, I turn on the laptop when it is plugged in, unplug it when the "Dell" on-screen progress bar finishes, then plug it back when the 'Windows' screen is displayed.

  It is an old laptop and I will soon receive a new, so I won't spend the money to buy a new AC adapter and the battery for XPS M1710, but I'd like to solve this problem, if it can be done otherwise.

  Thank you!

  I used to have this problem until it has just stopped working. Fact of the matter is Dell power supplies are designed for out of normal use. The cable for the tiny pin in the middle is broken inside the brick and was not fixed easily (you'd have to bust open the brick). Horrible design and this officially marks the last machine from Dell, I will never buy. With a registry hack that prevents the audit (ensuring the adapter you are using is Dell to make them more money), adapter is perfectly capable. I have an adapter 130W (XPS L1502X) and because of this my brother (Studio... not sure of the model). Mine came with the laptop at the time of purchase and the power adapter may not be recognized by me or my brothers laptop computer. Now my computer recognizes the cable my brother, but here's the catch: its cable is less common that mine and this can cause serious damage to my machine. When Dell said that it is a "security feature", it is so full of Bull. If that were the case, it would not allow that my brothers cable to go into my machine. Nice one Dell, you have lost a customer and I will make sure that everyone that I go looking for a new laptop does not buy your trash.

  I'm currently waiting on a replacement power brick that I ordered on ebay, so I can charge my laptop once again. Dell will charge you $ 70-80 to do this on eBay it's around $ 30-40 - all avoiding the retail margin.

  I do not throw accusations at Dell for the design of the brick to fail, I'm going off the coast of many positions of electrical engineers who have experienced the same frustrations and have taken it upon themselves to expose this type of scam.

• Drive Blu - ray of XPS M1710 in precision M6300?

  Someone tried to put the Matshita UJ-210 of BD - RE Blu - Ray burner in a Precision M6300? Would really like to be able to burn BD in my accuracy and commercial attaché Dell tells me that the only option for Blu - Ray in the M6300 is a BD burner No.

  The drive listed above is identical to that used in the XPS M1710. Don't know what model of car the M6300 is delivered with which is a non-bruleur. Maybe he will not support the precision MB? Anyone see a reason it would not work?

  The other BD burners that I should consider?

  TIA! : bravohelen:

  Joe

  Message edited by Rubicon-Joe on 23/06/2008 18:25
  
  

• Unable to sync the audio and MIDI

  I only managed to get a sound out X Logic Pro 5.1 surround in a 5.1 Logitech Z-906 - via a card external sound Sound Blaster X - Fi. It's great being about to pan my synths around the surround sound stage and bass is really great. There is a small problem that I can't quite get my head around. The Roland SH-01 synth running at 44.1 Khz (fixed). The Sound Blaster X - Fi works at 48Kz (fixed). No device can be changed these parameters.

  I can play the synth through the speakers without problem, but if I save it on an audio track, LPX complains about the disparity between the mIDI synthesizer and audio - it detects the 48 kHz and I get an error "error trying to synchronize Audio and Midi - sampling frequency of 48 000 recognized." Check the conflict between Logic Pro X and external device. LPX allow me to change the sampling frequency of 44.1 and 48 kHz, it is not available as an option.

  So yes, I'm aware of the conflict but I can't do something. Is there a work around?

  How do you save the Roland, through its audio output L/R in the SB X - Fi?

  The problem as you know, it's the USB output Roland of locks the system to 44.1 while the SB is locked at 48. Round it is to get an external MIDI interface and use DIN 5 pin to old for MIDI input/reading and audio recording via the outputs analog L/R in the SB.

  Another way would be to use Configuration Audio / MIDI (in utilities) and to create a global device.

  How to combine multiple audio interfaces by creating a Global device - Apple Support

  This will allow (in theory) OSX for re - sampled one of the devices to match digital clock speeds, it's a 50/50 crap shoot if it will work or not.

• can I play the guitar and midi keyboards at the same time?

  IM using the 3 main stage, I would like to play guitar and midi keyboards at the same time. I know that I can have more than one keyboard will at the same time, but I can't understand how to play the guitar too. I use a core Alesis 1 plug the guitar and a Keith McMillen 12 Step midi controller, he reads both just fine alone, but they play together. How can I get there? In addition, Im using a MacBook Pro OS X El Capitan.

  Thank you

  Mike

  You add a bunch of audio channels and affect the Core 1 Alesis entry?

  

  

• Why I get this error message: error while trying to synchronize audio and midi?

  I just updated Logic Pro and all of a sudden my lexicon alpha interface does not work correctly.  I get this error message: error while trying to synchronize audio and midi. Check for conflicts between Logic Pro and the external device. Help

  Start by making sure that the project in logic settings are set correctly - I think that the lexicon only supports 44.1 or 48.

  If it is software used to Setup place the lexicon make sure you that the sampling frequency is set to the same logic.

  Sometimes that power and the lexicon solves the problem...

  If none of the help above - make sure you use a multi-out or comprehensive audio device (OS X)

  

• Read the motor current by using the controller PXI-7350 and MID-7604

  I use the PXI-7350 controller and MID-7604 drive to run a motor drive.  I would like to be able to measure the motor current while moving the engines.  This measurement is possible?  If so, what commands are required to read the motor current?

  Hi Casey,.

  the 7604 can limit the current to a value that is selectable by the user and you can activate the current reduction if the axis is stopped, but there is no way to read the current engine. If you want to measure the motor current, you must do it with an external device, but due to the current chopping and multiphase, motor control stepper motors is not a trivial task. Micro step mode the current phase looks like a rough sinus with lots of harmonics signal, so you will need to do a true measure requiring RMS of expensive measurement equipment.

  Anyway. If you need to know the temperature of the motor you should better measure the temperature directly. The most inexpensive device OR do is the NI USB-TC01, but there are many other options available.

  Kind regards

  Jochen

• When you save a file, a message that Ecore: notation and midi has encountered a problem and needs to close.

  Original title: print the problem

  I use Windows xp. and still 4.5 to write and play music.  "When I try to save my score I get a message:" Ecore: notation and midi has encountered a problem and needs to close. Please inform Microsoft problem.  We have created an error report that you can send us' I sent this report several times, but have had no response.  Can you please help.    Thank you very much.   R.Windmill

  Hi R.Windmill,

  Thanks for the reply with the status of the issue.

  I understand that you are unable to download the clean boot article, receive error message: access is denied.

  What browser do you use to download the article?

  If you use Internet Explorer, I suggest to reset Internet Explorer to default values and check if it helps.

  See this link:

  http://support.Microsoft.com/kb/923737

  NOTE: Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.

  Alongside this, perform method 2, 3 of the suggested method in the previous post and we will reply with the results.

• I am trying to print jpeg images simple and every time I try to print the file asking to save to the XPS format, and even then he used to feel. What continues?

  I'm going to print an image

  I select the picture and size and press on print
  The computer then tells me to save it to an Xps file, and it will not print it
  Is happening?

  Hello

  1. Have you tried to open the image in another application (other than stick them in a doc) as standard Windows Picture Gallery and printing from there?
  2. You have installed the Microsoft office program on your computer?

  I suggest to set the default printer and check the status of the issue.

  Change your default printer

  http://Windows.Microsoft.com/en-us/Windows7/change-your-default-printer

• Compatibility M.2 SanDisk SSD X 400 with new XPS 8900 and cloning issues

  I just got a new 8900 XPS running and ordered a Sandisk X 400 1 TB SATA III M.2 drive for her.  I know, adding that a PCIE SSD with adapter would be much faster.  But I'm not a gamer and concentrate more on edge backup and storage.  And the new Sandisk card gets good reviews and should give a nice speed boost.  This will be my first attempt at cloning of a new boot disk and install an SSD.  I went through the forum and found some good information.  A few questions...

  One of the sons said that an SSD with the B and M keys (like this one) may not work.  Searching the Web I found no comments from anyone who has tried this particular SSD in a new XPS desktop.  No compatibility issues?

  Another thread has been posted problems with starting the XPS 8900, when you add a new disk, but the updated BIOS to 2.1.3 seemed to be the solution.  I confirmed that my machine already has this version of BIOS.  Once again, any concerns?

  My plan is to clone again SSD in the computer using Acronis or other software, then set as the boot drive in BIOS.  Is there a reason to delete the operating system of the C: drive, thereafter, or can just stay as a backup if problems occur with the SSD?

  I have already installed a few programs including MSOffice 2007 and Windows Essentials, so I can use the machine, but otherwise it is always very clean.  When I do the clone will be these OK execution since the SSD without much messing around?  And they will have to be uninstalled from the HARD drive?

  Thank you!

  X 8900-2508BLK
  I7-6700 / 3.4 GHz
  16 MB of RAM
  1 TB HARD DRIVE

  I'll answer some of my own questions.  The M400 Sandisk SSD drive arrived today and I found a screw M2x4 at Ace Hardware to install it with.  Installation was super simple.  I used a pair of pliers to hold the small screws in place and then a Jewelers screwdriver to fix it.

  He seemed to take more time for the first start that made me nervous, but all loaded without any problems.  I rebooted and that you press F2 to get into the BIOS and the new SSD was there!  And then let the computer loads Windows and checked Device Manager and it's still there!

  As expected the reader not yet appear in Windows because it was not formatted.  I used under Computer Management disk management to initialize the disk.  And now I have a new drive I: 935 GB free.

  So far so good.  Seems like the M400 Sandisk should work perfectly.

  Next step is to clone.  Always blazing new territory for me... when the drive is cloned it will remain I: or it will be C:?

• XPS-200 [and Dimension 5150C] memory addressable issue...

  I have a question on a very old PC - Dell XPS-200, Intel D 820 2.8 GHz, BIOS A07 - I am fixing to the top for a friend. Windows 7 Professional installed a 64 bit version of the operating system and properties system reports it as a 64-bit system. However, it shows that, although 4 GB of RAM is installed only 3.2 GB is used which is a message that I expect to see on a system 32-bit.

  As the Council and the processor are both 64-bit components I am at a loss as to why he is not seeing all of the 4 GB of RAM. There use a graphics Radeon HD 5450 and BIOS is set to allow only a very small amount of RAM so I don't think that's it.  According to the Intel chip plug the CPU has a 64-bit set statement and supports the extensions of physical memory on 32-bit, which allows him to address more than 4 GB.

  It seems to work OK and I know that if push comes to shove I can install a 32-bit system. But I understand why it is not recognizing all of the RAM and if there is any kind of patch/fix/update available for this machine that allows him to recognize all the 4 GB of RAM.

  When the XPS-200 [and Dimension 5150C] was introduced at Christmas 2005 were not a lot of choice of 64-bit hardware, so it came with a 32 bit OS, but I see he got an update of the BIOS in January 2007 which I would have guessed had to add extra CPU/RAM support but I can't find anything that describes what the A07 update was intended to do.

  Other suggestions from trash, use 32 bit, etc - I already understand these options :) - I hope that someone has enough technical familiarity with this machine/architecture to respond definitively to know if there is anything I can do to get it to recognize all the 4 GB of RAM.

  Thanks in advance for your help,

  Howard
  Redmond, WA

  PENTIUM D 945 chip sets not 5150/E510.   However, it will work well for 64-BIT windows 7 8 or 10 in a precision 380.

  Full 4 GB or 8 GB is fine precision 380 with 955 X chipset.

• Whenever I try to print something from my documents opens and says under xps. file and does not print

  Whenever I try to print something from my documents opens and says under xps. file and does not print. I also tried troubleshoot my computer and it says that my printer is not a driver and whenever he tries to fix it and says that it cannot install a driver. any help would be appreciated

  Looks like you have the default printer configured to be Microsoft XPS Document Writer.  Go to control panel > printers and devices and see which printer is enabled in a green circle.  If this is the XPS Document writer as I suspect, you can right click on your printer and then select "Set as default printer" after you do this, or if you cannot do this, answer with the brand and model of your printer and we are able to help if you have a driver problem.