Z210: Z210: RAID 1: failure of a disk. How to replace?

Similar Questions

• After upgrading RAM, computer stops and gives error when restarting: "DISK BOOT FAILURE, INSERT SYSTEM DISK".

  Original title : OFFICE XP STOPS (MESSAGE of ERROR)

  I get the message "DISK BOOT FAILURE, INSERT SYSTEM DISK". I just added more memory to my 512 RAM. I USED MY XP TO REBOOT DISC, BUT THERE ARE ALWAYS AFTER PRESSING THE KEY 'R '. ONCE IT STARTS AND SE PAST JUST STOPS AND THE ERROR MESSAGE IS POSTER AGAIN UPWARD. I HAVE THE SAME 'MSCONFIGED' IT NORMAL TO SELECTIVE. I WAS ABLE TO GET INTO SAFE MODE, BUT NOW IT WON'T. I GET JUST THE ERROR MESSAGE.       > WHAT AM I DOING WRONG

  Hello

  You can view these methods:

  Method 1: As a first step, check to see if the hard disk becomes detected or listed in the Basic Input/Output system (BIOS). Also, be sure to change the boot order in the CMOS settings so that thehard drive is the first on the list.

  Note: To learn how, see the documentation provided with your computer or contact the manufacturer of your computer.

  Note: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from configuration can resolved BIOS/CMOS settings. Changes to settings are at your own risk.

  Method 2: If the manufacturer has installed the Recovery Console on your computer, perform the check disk to fix this.

  At the recovery console command line, type:

  Chkdsk /r

  When you restart your system, your computer will be scanned for errors and will try to correct them.

  Note: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  For more information, see:

  How to perform disk error checking in Windows XP

  Chkdsk

• Boot failure insert system disk and press enter

  The computer I have was given to me. It has been completely removed with a program called "wipeout." I loaded my OS on it and everything seemed fine at first, but each time the computer restarts I get error boot disk failure insert system disk and press return.  What can I do?

  Initially to verify that the drive is identified in the bios (as soon as you on Btn led pwr hit several times)

  If it is not identified 1) the reader has not 2) an internal connection has departed

• Err1err3 Boot failure Insert system disk and press enter

  OK lets see if you can crack this for me, it started a week ago for me. If I leave my computer on as usual, he would go on the eve, duh. BUT now it would not start up instead of this I have a black screen and reboot I go to the blue HP screen with four options. Well I have tried for some time and managed to get Vista back up...

  Well, after that it started to get really slow and started freezing up during my loadup office. Then, after many hours of scanning and research and reading aid, after a virus scan and even a system restore I couldn't understand the problem and I did what for me was the unthinkable...

  A COMPLETE FACTORY RESTORE... I wiped my computer with the possibility of returning to factory install settings. And for a while, that was good, that he has worked again... TIL yesterday I let go to the screen saver and then sleep mode while I was away, and what to do, I see but once more

  ERR1ERR3 Boot failure Insert system disk and press enter

  so clues as to why this is happening.

  PS right now YES I download the bittorrent to vista repair which had been suggested in another thread pray that it will work, but until it's done, I wanted to share this and ask for anyone who might have an idea of what caused it.

  Hello

  Run the diagnostics and the other utilities that I posted.

  ---------------------------------------------------------

  Starting from your startup disk COMMAND prompt, run these (you can run them in windows, but can be
  more efficient prompt startup disk so I will list two meanings).

  A boot disk command prompt

  Chkdsk /f /r

  RESET

  sfc/scannow

  RESET

  ---------------------------------------------------------

  Inside Windows - regular or Safe Mode

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  --------------------------------------------------------

  Back UP your data NOW!

  Good luck.

  Rob - bicycle - Mark Twain said it is good.

• Disk Boot Failure, Insert system Disk

  Hello

  My HP Pavilion media center m8100n shows "Disk Boot Failure, Insert system Disk"

  I searched on HP support, but I couldn't find a solution from the recovery disk is not available

  Any help would be appreciated

  You are the very welcome.

  Somewhere on the top or side of your PC case, there should be a multicolored Microsoft Certificate label of authenticity (COA) with 25-digit Windows Vista product key.

  It should look like this.

  

  Paul

• SMART FAILURE PREDICTED ON DISK HARD 0: WDC WD2500BEVT-08A23T1-(PM)

  Hello

  I use the Lenovo Thinkpad SL510 with windows 7 ultimate 32 bit authentic. All of sudden my laptop displays the following error during startup:

  SMART FAILURE PREDICTED ON DISK HARD 0: WDC WD2500BEVT-08A23T1-(PM)

  WARNING: Immediately back up your data and replace your hard drive. A failure may be imminent.

  Press F1 to continue.

  I tried to press F1 so many times, but it is not booting. I did tests of difficult diagnosis and he showed the result as "PASS for read & speed test '.

  Please help solve this problem as soon as possible.

  Hey, @sumukhreddy!

  I'm really sorry to hear about your WD drive problems. However, I recommend you to use Data LifeGuard Diagnostics from WD (DOS version) to test again and check on the health and the SMART State it. The DOS version of the utility will allow you to perform diagnostics without having to boot into any operating system. You should be able to find under downloads by product once you select WD Caviar Blue.  You can extend the WD software link and follow the instructions.

  The drive is OEM and most likely came with your laptop, so I recommend you to contact the manufacturer and check the warranty of your laptop. It is always covered, you can RMA and they should be able to provide a repair and the implementation of the defective material.

  Good luck! I hope I've been helpful! :)
  SuperSoph_WD

• replacing a drive RAID 1 failure in PowerEdge T710

  I just got the disk(146GB) of replacement for one of the disks RAID 1 has failed. I would like to know what the best approach is to replace the defective with the new one (same size), now that the spare drive (300 GB) is used by the raid. I want to get the bigger drive and re - assign as a global hot spare, by the original configuration is possible without disconnecting the server?

  Here is my config:

  T710 Server (8 discs - 4 X 146 GB, 4 x 300 GB)

  PERC H700 integrated

  2x146GB drives - RAID 1

  2x146GB drives - RAID 1

  3x300GB drive - RAID 5

  1 x 300 GB disk - hot spare

  Thank you.

  This should work for you. What it will do is essentially the same process I described. When you insert the replacement drive and implement the Member to replace it will fail then the immediate replacement and then start reconstruction on replacement.

• What should I do now? I have a boot failure of the disk (insert system disk). I inserted the disc and it says:

  Compaq sr5127cl vista 32 bit boot disk failure, insert system disk

  I inserted the disc system and got "No drive found" upwards cannot continue

  What should I do now?

  Datsuny wrote: Compaq sr5127cl vista 32 bit boot disk failure, insert system disk I inserted the disc system and got "no drive found" set up will continue what should I do now?

  Hello Datsuny, many times this error means that the hard drive has failed or the operating system on the hard disk is damaged.

  I would tend to think that the hard drive has failed.

• How do I get Windows to reinstall after the total failure of the disk?

  I had to replace my hard drive, but how to get Windows Vista version licensed as was preinstalled on my broken drive?  Thank you

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/default.aspx/KB/326246

  'How to replace Microsoft software or hardware, order service packs and upgrades, and replace product manuals'

  See you soon.

  Mick Murphy - Microsoft partner

• Hard drive failure is imminent and must be replaced

  HP TouchSmart 610-1020 has

  i5 6 GB RAM 64 bit

  Windows 7 Home Edition Premium--> Windows 8

  Hi there, since a terrible week for me I started to receive the error message:

  Hard drive failure is imminent and must be replaced

  only when am re - / from my PC.

  I made a backup already a few days ago (space available was already 85% - did not much), run all those disk cleanup, defragmentation, analyze and verify programs and there was nothing wrong. I ran all possible controls and it had nothing recorded. I've updated / installed Windows 8 which works perfectly without any problems, no computer crash or that it is, but only sometimes receive a message saying that I need to run/shedule a back, etc.

  As I already mentioned, there was no disk error, no other problems known but still get the message "hard drive failure is imminent and should be replaced" and crazy!

  My questions are:

  (1) what on Earth is happening, there is always a problem with touch smart PC; should he stay away all in a desktop PC and just buy older versions - separate screen and tour, etc.?

  (2) I have no problem and continue to use my PC but wonder what will happen; It will be down, it's just a false error message, what should I do?

  (3) if I have to take it to a service, what should I take care of?

  Thank you for taking your time and wil appreciate for your posts about.

  Alp

  Hello

  What has happened is that the CHIP system reports told you that your hard drive will fail little time. It is good that you have saved.  The fault lies not in all of your PC, but in a single component, namely the hard disk. You own your PC like one year standard warranty is longer.

  You need to buy a hard drive with the following specifications. It of time to find your recovery disc as you need to recover your PC in its delivered State and then apply the upgrade 8 to win again. You can install it yourself or have done by a qualified PC store or from an HP Service Technician. The HP service center is the most expensive option.

  You can avoid having to use the recovery disk and upgrade by a clone of your hard drive on a 1.5 TB external drive. You will be able to migrate the clone on the new diskette with a product commercially available as Paragon Hard Disk Manager 12.

  • Size: 1.5 to

• Airport utility in windows 10 detect but wireless internet does not detect the hard disk, how to do?

  Airport utility in windows 10 does not detect the hard disk, how to?, the Office detect wireless internet no hard drive.

  What hard drive? It of a time capsule, or is it a drive connected to an airport extreme?

  What model number is the most convenient airport?

  Any plugged into USB drive must be formatted FAT32 (no other type of FAT as exFAT) or HFS +, IE standard Apple format.

  In addition, not all drives are recognized.

  The internal drive of the TC must be recognized, but there could be problems as well according to the age.

• Forgotten password for XP user account and did not password reset disk, how can I get in

  Forgotten password for XP user account and did not password reset disk, how can I get in

  Michael, Microsoft technical support engineers cannot help you recover the passwords of the files and Microsoft who are lost or forgotten product features. For more information about this policy, please refer to the below sticky... http://social.answers.Microsoft.com/forums/en-us/w7security/thread/39f56ef0-5d68-41AD-9daa-6e6019c25d37

• How to replace a bad IDE disk with a USB Flash drive system - and have all the functionality of XP Pro SP3

  How to replace a bad IDE disk with a USB Flash drive system - and have all the functionality of XP Pro SP3
  Given a PC without hard disk...
  How can you use a flash drive instead?
  So, indeed, the USB key works as an SSD...
  I saw online options that gives partial functionality of the system... and an option that is more than $100 (more than the system's worth)...
  None of these options are acceptable in the circumstances.
  It is an effort to create a machine for a particular use, built from a recycled pc for which hard drive was removed and destroyed by the original owner...
  The criterion is that it must work just like it was a mechanical drive running xp pro sp3 with all updates, etc...
  Thanks for any help.

  You can not install XP on a Flash as his unsupported drive. Your only two options are a traditional hard drive or Solid State Drive (SSD).

  J W Stuart: http://www.pagestart.com

• I have the genuine product key genuine microsoft windows vista business but I have lost the cd/dvd of the windows disk, how to manage another copy of windows vista professional?

  I have the genuine product key genuine microsoft windows vista business but I have lost the cd/dvd of the windows disk, how to manage another copy of windows vista professional?

  If you bought the retail of Windows 7:

  How to replace Microsoft software
  http://support.Microsoft.com/default.aspx/KB/326246

  If Windows is preinstalled with the computer:

  If you do not install disks:

  Contact the OEM computer manufacturer and ask them to send you an installation to your computer disk - they may charge a small fee. Contact information for the manufacturer of your computer can be found here:

  http://support.Microsoft.com/GP/oemphone/

• If I do not have a windows vista sp2 install disk how can I erase all programs and files from the laptop?

  I would remove ALL of my laptop which is running vista Sp2 and I have not a disk to install it from what can do?

  Hello

  Here are the different ways to reinstall Vista

  Contact the manufacturer of the laptop computer and ask them to send you to vista recovery disks to reinstall the operating system back as it was when you bought it

  they do it for a nominal cost of $

  ____________________________________________________________

  also ask them if you have a recovery partition on your hard drive to get back to the way you bought

  you would normally press F8, F9, F10 or F11 or Alt + F10 or 0 to start to start the recovery process according to the manufacturer

  Ask them of the exact key sequence

  __________________________________________________________

  or borrow a vista microsoft dvd; not a HP, Acer recovery disk etc

  Make sure that you borrow the correct 32-bit or 64-bit microsoft dvd to your computer

  they contain all versions of vista

  This is the product key that determines which version of vista is installed

  http://www.theeldergeek.com/Vista/vista_clean_installation.html

  ____________________________________________________________

  How to replace Microsoft software or hardware, order service packs and replace product manuals

  http://support.Microsoft.com/kb/326246