Re: Satellite M100: BSOD at each start of the first up - but ok after that

Similar Questions

• Satellite C660 is unable to start for the first time

  I have a Satellite C660 - PSC0AQ-03C019 + 1B194392K

  For the last year laptop worked fine in the last 2 months, however he had a problem starting. The first starting attempt of the day, it does not start, it is consumed on gets in front of splash screens after the cursor flashing in the top left then hold with a blank screen (not the cursor just a low glow).

  Hold down the power button / turn off and turn on again then the computer will start. sometimes (not always), it will ask to start normally or repair.

  The laptop works perfectly in use does not fall out of mistakes. Restarting the laptop works as expected close and turn on/off after 5 minutes works great.

  If the laptop is left for an hour or more, it starts the same as above. turn off and turn on/off the system will start but with boot normally the question.

  He has not indicated in the error logs files

  I did a full reinstall of HARD drive recovery system.
  I did a full system reinstall from recovery DVDs.
  I did a full system reinstall from DVD disk a hard new recovery.
  I replaced the ram

  I tried to update the bios, but get an error
  BIOS version more than 200
  Battery capacity over 10%
  AC is attached

  Hello

  The description of your problem is, for me, quite confusing, and I do not understand your problem.
  Can your notebook load and start the preinstalled operating system or not?

  Enter the BIOS and set it to default settings. After that restart your laptop and to describe what is happening exactly.

• Using Firefox 4 and Windows 7. Whenever I have to start Firefox from a shortcut to a Web site, what happens with the following error "there was a problem sending the command to the program". The requested site is loaded after that. without any problem.

  Using Firefox 4 and Windows 7. Whenever I have to start Firefox from a shortcut to a Web site, what happens with the following error "there was a problem sending the command to the program". The requested site is loaded after that. without any problem.

  If a shortcut is used while Firefox is already open the error will not occur.

  For me, the problem was the FoxClock extension. Once I disabled it, the problem was gone.

  Hope this helps.

  Olivier

• I accidentally deleted all my settings and the apple iphone 6 s ID. Now I have to activate my phone and start from the beginning. But I don't have my EA sim with me right now and cannot organize any sim EE. How can I activate my phone without sim card?

  I accidentally deleted all my settings and the apple iphone 6 s ID. Now I have to activate my phone and start from the beginning. But I don't have my EA sim with me right now and cannot organize any sim EE. How can I activate my phone without sim card?

  Sorry, but you can't activate an iPhone without a SIM card installed. It is simply not possible to do.

• HP Pavilion Notebook 15-ab083T: laptop upgraded before even starting for the first time = problem?

  Hello!

  I recently bought this laptop with the intention to replace the hard drive (1 TB HDD 120 GB SSD), as well as upgrading the ram from 8 GB to 16 GB. The problem is that I have improved these things before you start for the first time. And now it complains that it cannot find a device boot, even when I insert a USB key with windows 10 iso on it. Or a cd with windows XP. He needs to have the HDD windows 8.1 original in it on first commissioning? It took a while to replace parts...

  Thanks in advance.

  That's very true, I used gparted before checking this again, and it was corrupted. Very well! I ended up installing windows 10 home using a free student license. It's perfect, since I have windows 8.1 before running on the 1 TB hard drive and it was filled with bloatware, thanks to HP (no offense). So, it is nice to have a clean install. Everything works fine now, I had to change some settings of 'Legacy Boot' in the bios to boot from the USB.

• XP does not start on the first try to start

  I just reinstalled XP Pro SP3 on new 250 GB HD HD partitioned C - equal D. DΘmarrage initialization stops and I have to hit reset in order to get Windows to load. Any ideas on what I should do to correct so machine will start on the first try.

  If the CMOS battery on the motherboard is dead, it may take two or three attempts to start re-namely configuration of the BIOS of your system.  If your time is incorrect immediately at startup, this could be another indication.  Look on your motherboard for a button size battery shift.  Check the documentation for the computer from the manufacturer of your Web site.

  You can also try a chkdsk with the repair operation (/ R) option if you have problems with your file system.
  "How to perform disk error in Windows XP check"
    <>http://support.Microsoft.com/kb/315265 >

  HTH,
  JW

• my windows vista starts normally until I have pass the user coice screene. After that, I see the cursor but everything is black. What should I do? Thank you very much!

  my windows vista starts normally until I have pass the user coice screene. After that, I see the cursor but everything is black. What should I do?

  It was probably caused by the removal of any file system as I was scaning the pc for malware and probably deleted some important file. only safe mode works now
  and I need my computer quite urgent for the University.
  Thank you very much!

  Hello

  No saving necessary data and re-installing Windows Vista might be the best option, but here
  are a few others.

  You can save your files by putting the drive in another computer as a 2nd disk (best) or external
  Drive USB enclosure and then backup to removable media such as CD, DVD or other USB drives.
  Of course a real store of the computer or the manufacturer of your system can help to recover the files.

  Or you can use a boot Ubuntu CD to back up data.

  Use Ubuntu Live CD to backup files from your Windows computer dead
  http://www.howtogeek.com/HOWTO/Windows-Vista/use-Ubuntu-Live-CD-to-backup-files-from-your-dead-Windows-computer

  --------------------------------------------------------------

  You can access Mode safe? Repeatedly press F8 as you start? If yes you can try Control Panel - device
  Manager - graphics card - Double click on - driver tab - click on UPDATE driver - then right click
  on devices and UNINSTALL - REBOOT.

  A method to try to get to the desktop (try in normal Windows Mode without failure) is CTRL +.
  ALT + DELETE - Manager tasks and tab process EXPLORER.exe and COMPLETE the PROCESS on this subject - and then
  on the Applications tab - lower right - new task - type in EXPLORER.exe. Safe mode is available by
  repeatedly tapping F8 as you start. CTRL + SHIFT + ESC also begins the Task Manager.

  First check this thread in case it is simple and if not to come back to this thread.

  http://social.answers.Microsoft.com/forums/en-us/vistaprograms/thread/50247d5e-0ae0-446c-A1bd-11287fd1478a

  Black screen problems are extremely difficult to repair and all patch is usually on a base hit or miss.
  That there is no information on a black screen as it is on a blue screen just adds to the
  Difficulty. Often using a restore point or Startup Repair will have no effect. You can try a
  Google to see the proposed repairs, whom some have worked however these cover a wide
  field efforts.

  Here's a video of one of them.

  http://www.Google.com/search?hl=en&q=black+screen+of+death+Vista&btnG=search&AQ=f&OQ=&AQI=G1

  Here's another fix
  http://blogs.PCMag.com/SecurityWatch/2008/12/the_mysterious_black_screen_of.php

  You have a Vista disk? You can try restoring the system to it. If you don't have the disks your
  system manufacturer will sell them at low prices. Or try in safe mode if you can get there.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  You can create a recovery disc or use someone even version (making the system restore it)
  must be bootable).

  How to create a Vista recovery disk
  http://www.Vistax64.com/tutorials/141820-create-recovery-disc.html

  ------------------------------------------------

  These require the correct Vista discs since you can not start safe mode.

  Try the Startup Repair tool-

  This tells you how to access the System Recovery Options and/or with a Vista disk
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  -----------------------------------------------

  Here are a few Google searches where many have found different solutions:

  Vista black screen - check that a 1st
  http://www.Google.com/search?hl=en&source=HP&q=Vista+black+screen&AQ=f&OQ=&AQI=G10

  Vista black screen Solution
  http://www.Google.com/search?hl=en&q=Vista+black+screen+solution&AQ=f&OQ=&AQI

  Vista black screen Fix
  http://www.Google.com/search?hl=en&q=Vista+black+screen+fix&AQ=f&OQ=&AQI

  -----------------------------------------------

  If necessary and you can access all ordinary Windows.

  You can try an In-Place Upgrade (hopefully save programs and data) or a repair installation
  (if all goes well, the data records and need to reinstall programs). Be sure to do a good backup or three.

  You can use another DVD that aren't copy protected but you you need to own
  Product key.

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  If nothing works, you can make a repair facility that must save the data but you will need to
  Reinstall the programs. This also requires correct Vista disks especially for OEM versions. You will be
  need to know your product Code.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-the-recovery-console

  How to perform a repair for Vista Installation
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  ---------------------------------------------------------------------------

  Another method that works sometimes: at the command prompt, type of Vista startup disk:
  (a line type or copy and paste one line at a time and hit enter - enter a bracket)
  or "BOLD")

  c:

  cd\

  CD c:\Windows\System32\winevt (there is a space between cd and C :)

  Ren LogsOLD Logs (there are spaces between ren and newspapers and Logsold)

  RESTART Windows

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• BBM BBM voice - can not hear each other for the first 5 seconds

  Hey. Has anyone else noticed that on BBM (Q10 10.3) calls iPhone BBM, you sometimes can not hear each other for the first five seconds? Don't know if it's in the app or data connection or what...

  J.

  I just recently noticed that he actually said 'connection '. "during about 5 + seconds. So it's ok, I guess I'll wait five seconds.

• Some programs do not correctly start on the first try.

  I don't know when or why it started, I'm leaning towards one of the updates. After this point, some installed programs - date of exit of Atari from the edition of Unreal Tournament 2004 Editor and some games via Steam from Valve application for example - began to refuse to start correctly the first time. But on the second, it will be.

  Here's a breakdown of what's going on.

  1. I click to start a program.

  2. the process is, but the program does not work.

  3. I click a second time.

  4. the progress process begins again and the program starts very well.

  Strange things.

  1 Quiting the first process has no effect on the second attempt of result.

  2. does not occur with Microsoft programs I've used. (

  3. steamed, the problem first start levonorgestrol less often launched from the steam window that shortcuts (always failed the first time through the shortcuts)

  4 steam itself doesn't have this problem.

  5 unreal Tournament 2004 works better (errors are rare) on Windows 7 it works on Vista.

  I have Windows 7 Home Pre - 64 bit

  If using the main .exe in the games installs folder work properly remove current shortcut
  and make a new shortcut to the main .exe.
  R / click on the .exe and select - send to - Office.

  If there are problems with the boot via the Steam client you can find the best suggestions on
  steam or via Steam faq forums.

• For psc 1315: before you can use this feature, OneNote 2010 must start for the first time.

  I installed the downloaded software (Windows 7) for my old psc 1315 (all-in-in-one). It printed the page sample after installation, but when I want to print what this or else it gives me the following message is displayed:

  "Before you can use this feature, OneNote 2010 must start for the first time."

  Restart the PC does not solve the problem either. How can I get the printer to work?

  Hello pietpompies7

  See the following Microsoft Office Blog article. It deals with OneNote arise while you try to print.

  Microsoft OneNote is misuse of your print jobs?

• When I try to start lightroom 6 it opens only the first window, but nothing more. ligthroom closed several times, restarted the computer, update system, nothing. What can I do?, when I try to start lightroom 6 it opens only the first.

  When I try to start lightroom 6 it opens only the first window, but nothing more. ligthroom closed several times, restarted the computer, update system, nothing. What can I do?, when I try to start lightroom 6 it opens only the first.

  Hi silvers.

  Please make sure that your graphics card and Lightroom 6 are up-to-date. Latest version of Lightroom is 6.4.

  Please check the FAQ and troubleshooting of Adobe Lightroom GPU and disable the use of the GPU in Lightroom.

  What is your operating system?

  Kind regards

  Assani

• Hi, I'm rookiee and I just started with the first steps of creating a Web site. the katies-coffee-building file is on my desk and uplouded in the library. That has worked well. Now I'm putting the button in Photo Shop (banner), I have pull down on file/pl

  Message "Hi, I'm rookiee and I just started with the first steps of creating a Web site. the katies-coffee-building file is on my desk and uplouded in the library. That has worked well. Now, I'm putting the button in Photo Shop (banner) in. I pull down on the file Photo Shop button instead and try to select the Banner.psd file. Unfortunately all of the (active) folder is not accessible to all. One is not visibel. Please - need some help here. Thank you.

  @Ach ja, meine Muttersprache ist Deutsch

  You must use the file > Place Photoshop button (Cmd / Ctrl + B).

• Satellite M100-152 does not start

  Title says it all.
  When I'm back from the IGC-pause the screen was empty but of cold cathode (backlight) have been turned on yet.
  Fact a reboot by turning the PHONE works but the screen remains dark with cold cathodes offshore.

  Hard drive starts spinning so the cd rom (with disc inserted i.e.) but nothing happens otherwise.
  The only thing is that cell phone ring 4 times.

  Cannot change the boot sequence / device
  Don't start with the restore cd.

  Any suggestions / ideas what could be wrong?

  > The only thing is that cell phone ring 4 times.
  Looks a bit like a hardware problem. Usually, if the laptop will beep then an error has been detected on the Board!

  Seems that the portable technician should take a look at this machine.

  But have you tried to remove the battery and the AC adapter from the laptop for a while?
  Please check if this help

• Satellite L350-170 - won't start, only the BSOD

  Laptop of my son froze the other night and he had to turn off manually. He started upward once again some time later and this message appears on a BLUE SCREEN.

  * A problem has been detected and Windows has shut down to avoid damaging your computer

  * If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps: *.

  * Make sure any new hardware or software is properly installed
  * If this is a new installation, ask the manufacturer of your hardware or software for the windows updates if you need.*

  * If problems continue, disable or remove any newly installed hardware or software. Disable the BIOS memory options such as implementing caching or shading. If you need to use safe Mote to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode.*

  * Technical information: *.

  * STOP: 0 X 00008086 (0 X 00000000, 0 X 00000000, 0X00000000, 0X00000000) *.

  We have tried to start in safe MODE but nothing seems to work and I was wondering if someone could help?

  Thank you very much

  Dave

  Hello

  If SafeMode doesn't work too, the problem seems to be related material or your Windows installation is damaged. You have something has changed or installed on the laptop? If this isn't the case, I would test the RAM modules with special diagnostics, like Memtest86 tools. Use Google to find (freeware software).

  If Memtest86 can t find mistakes, I would try reinstalling Windows using Toshiba recovery disc.

• Satellite C660-108 does not start if the USB Bluetooth dongle connected

  Hiya,

  I hope you could help me.

  I'm having a problem with my dongle bluetooth and satellite c660-108.
  It all works perfectly. It connects devices via bluetooth and I can do whatever I want.

  But then when I'm mobile stop and turn it on again it will go if the bluetooth dongle is always in the USB.

  I see Toshiba screen and then it hangs with a black screen and a cursor flashing at the top left.
  I have to turn it off, remove the bluetooth dongle and then turn it back on.
  And then windows starts. After that, I put in bluetooth dongle, once again I want to work with her.

  It isn't a huge problem, but it is a bit annoying when I have to leave the bluetooth and put it back again to get the windows began.
  I'm running under win 8.1 but he already had with 8 victory.

  Anyone any ideas?

  > I see Toshiba screen and then it hangs with a black screen and a cursor flashing at the top left.
  Especially the blinking cursor is displayed because the laptop can not find a boot device.

  It seems that the device cannot put on the HARD drive while the USB dongle is connected.
  I would recommend you check the boot order in the BIOS.

  Put the HARD drive in the first place and the USB boot last device.
  Save changes and check if it helps.