15 - an001na: Star Wars Limited Edition 15-an001na Hp laptop

Hello I want to upgrade the laptop with 16 GB of ram, here are the specs of RAM:

HyperX HX318LS11IBK2/16 two 1 x 64-bit (8 GB)
CL11 DDR3L - 1866 MHz SDRAM (Synchronous DRAM) 2Rx8, low voltage, memory, modules from the sixteen elements of FBGA DDR3 512 M x 8 bits per module. Total capacity is 16 GB.
Each module kit has been tested to operate at DDR3L - 1866 MHz at a time of low-latency on 11/11/11 at 1.35v or 1.5V

So, I want to implement SSD with 540mbs/520mbs read/write speeds

My question is is this laptop supports this type of RAM with 1866 MHz and it uses connection sata3 that can support the SSD speeds?

Thank you.

Kind regards
Andrius

Based on my experiences with HP laptop very similar (ab231na) to be exact, you should be perfectly fine. However, I would recommend 8 GB of RAM unless you feel you really need 16 GB, it's your choice to make. For the SSD, I recommend the Samsung 850 EVO, it is powerful for the money and it is Samsung. Yes, the laptop will support SATA III 6 GB/s, which allows for maximum performance of the SSD.

Tags: Notebooks

Similar Questions

  • Pavilion Notebook - 15 t-ab100: Hp star wars limited edition laptop

    I have a Pavilion Notebook - 15 t-ab100 CTO is therefore limited edition Star Wars with touchscreen a 2 TB hard drive. You want to swap hard drive on a 1 TB samsung SSD. Looks like the whole bottom is 1 piece. Not sure how he defeated hard disk access. You remove the screws of the hinge end monitor? When I removed all the screws from the bottom, the bottom base was still on tight at the top of the laptop. So not sure how it is apartment. Other features include a dvd player. Don't want no ro break my new laptop. I took cases for laptops out there before, but this one is a little trickier. Any info is appreciated.

    Hello

    Please download the manual below for your laptop and check page # 49, which shows how to remove the hard drive.

    http://h10032.www1.HP.com/CTG/manual/c04642845

  • STAR WARS 15-an001na HP: slot m2 15-an001na HP STAR WARS SPECIAL EDITION?

    Hello.

    I would like to ask any SSD on my STAR WARS 15-an001na HP, but I can't find record of ditailed to see if the MB has additional location SATA or m2. Can u pls addvise.

    THX.

    Yes, he sees s. 53 of the Manual:

    Star Wars laptop manual

    Remove the bottom cover to access the slot, but it can take a drive SATA M.2 2280 mm module.

    If it's 'the Answer' please click on 'Accept as Solution' to help the other ifnd it.

  • Star Wars™ Special Edition: Restore my laptop

    I have a question about the restoration of my Hp laptop special from star wars edition. If I restore and have it remove all of the files and what not I lose all the features that came with the laptop? as the command centre which has all the star wars related functions and will it take me to get the driver for the led keyboard or anything? Thank you!

    on a side note, I want above all to restore it to return to its original speed and get all the space that I filled out back. I have only about 35 GB spread of TB thanks again!

    BradlyHawke wrote:

    I have a question about the restoration of my Hp laptop special from star wars edition. If I restore and have it remove all of the files and what not I lose all the features that came with the laptop? as the command centre which has all the star wars related functions and will it take me to get the driver for the led keyboard or anything? Thank you!

    on a side note, I want above all to restore it to return to its original speed and get all the space that I filled out back. I have only about 35 GB spread of TB thanks again!

    If you use the plant holder of HP recovery that it comes from the factory with which should be what is was, but if your not sure you need to contact HP support and ask them.
    Contact - HP customer support

  • Star Wars Special Edition Note: This system is not supported

    I need help for the Star Wars content on my laptop special edition of Star Wars.  I had to have my hard drive is erased after it got a virus and for some reason any now when I installed the Star Wars command center it tells me "this system is not supported. What should I do to get back what I lost and how do I get the command center working again?

    Hey @JudyInCT,

    Welcome to the Forums of HP Support!

    I understand that you have some problems with Star Wars software on your laptop. I can help you with that, but I need the model number of your laptop first. You can find the model number in this link. Once I know that I will be better able to help you.

  • Star Wars Special Edition Note: death star icon recycle bin empty

    So my trash was a star of Rush's death, but windows then decided to download an automatic update and now his party back to boring standard basket. How can I get that back? I went into the settings - customization - themes - desktop icon settings, but could not find the icon of anywhere.

    Hi there @TomMJ19,

    Welcome to the Forums of HP Support! It's a good place to find the help you need, other users, HP experts and other support staff. I understand that you have a problem with the recycling bin icon. I'll be happy to help you.

    It is a part of the Microsoft Windows software, and update return by default.

    Here is a link to change the appearance of the Recycle Bin.

    How to change the theme, lock screen & desktop wallpaper in Windows 10 if it was a Star wars theme.

    Please keep me informed of the progress of things.

    If you need help, let me know and I will gladly make all that I can to help you.

    Please let me know if that solves the problem by marking this post as "accept as a Solution.
    To simply say thank you, click the Thumbs up below!

    Thank you.

  • star wars command center problems

    Hello, I just took possession of a portable star wars limited edition, I can open the command center, but I need to know how to raise R2D2 and the small figure in light, thank you very much

    Hi @garyrwhitaker,

    Welcome to the HP Forum! It is a wonderful location to converse with the community, get help and advice. You have a rewarding experience, I would include the following link for your perusal and reference. First time here? Learn how to publish and more.

    I understand you've got a laptop HP from Star Wars limited edition. You can open the command center, but t you want to know how to make appear R2D2.  After some research, I believe you can do it by choosing one of the special themes Windows as we should be R2D2.

    Please let me know the results.

    Thank you for your participation in the Forums of HP! We want to help you as well as others who may encounter a similar problem. "Think about scoring the post that solves your problem as" ","accept as Solution " to help other members of the community! To say thanks for the help, please click "Thumbs Up icon" below.

  • Special Edition of star wars: recovery failed

    Hello

    I have a laptop HP Star Wars Special Edition (15-an001na). After two days of its use for some reason windows stop responding and I coundt find a way to solve it so I tried a recovery of the plant. Manager of recovery is not so I can't do anyting with the laptop now. Any ideas how to solve this problem. Any help is appreciated. THX

    PS. So Exuse my English is bad

    Hi @Cornel_h,

    Welcome to the HP Forums!

    I read your post and wanted to help.

    I understand that the Recovery Manager doesn't have on your laptop. And your laptop crashes or hangs sometimes.

    You can start the laptop into Windows now? If the laptop is unable to start, try the last link on this document: HP - computers perform a recovery of the system (Windows 10) HP

    If you can start the computer normally, try the steps in this document: computers HP - computer crashes upward or freezes (Windows, 10, 8)

    If this post helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me congratulations.

    Kind regards

  • 15 - an051dx: special speaker and backlit keyboard questions about Star War Edition

    Hi guys, I just bought Star War Special Edition laptop with B & O speakers. Is there anyway can I change that in order to get better sound quality on my laptop? In addition, the laptop comes with backlit keyboard, therefore is anyway can I adjust the timing for her? Thank you and have a nice day.

    Hi @StevenChau,

    Please use the following link to create yourself a file number, then call and it can help to expedite the appeal process:

    Step 1. Open the link: www.hp.com/contacthp/
    Step 2. Enter the product number or select Auto detection
    Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
    Step 4. Scroll down and click on: contact HP options - click Get phone number

    File number and phone number are displayed.

    They will be happy to help you immediately.

    You can say thanks for trying to help by clicking on the Thumbs Up below!

    Thank you.

  • Special Edition of star wars HP: Dvd rom starting up/reboot

    Hi everyone I recently bought the laptop HP star wars Special Edition and I just noticed each time I restart the laptop the dvd rom will make a noise happens also after it starts. Is this normal?

    @AntiMatter

    Forums can be with you

    I understand that DVD drive of the laptop makes a noise whenever you have be turn on or off.

    I need some clarification on a specific solution:

    What is excessive noise?

    When was the last time that you did not have this problem?

    Did you install updated BIOS, lately?

    Have you have performed the steps on your own before posting on the Forums of HP?

    If you are unable to reach a resolution, please click on accept the Solution to help others with similar issues.
    If you like my assistance, please click on the thumbs up icon.
    The two icons are below this post.
     
    Have a good day Ahead.

  • Star Wars 15-an002ns: SSD installation socket m2

    Hello

    Recently I bought HP Star Wars Special Edition laptop for laptop - 15-an002n, which comes with 1 TB of HDD. I think it is too slow for the overall power of the rest of the components, and I intend to install a SSD for the OS. Consulted the manual, I see that the laptop has a blank m2 socket and some versions include an SSD there:

    M.2 SATA-3 (NGFF):
    ● SSD 256 GB, 2280, M.2, SATA-3, TLC

    I installed some other SATA III SSD, but never a type m2. My questions are:

    1 are there compatible with lower capacity models? I want to just install the OS here, so it would be enough with M.2 128 GB SSD.

    2 how the BIOS will recognize the new drive as primary drive? I need to change the settings?

    3. I alter anything else in the computer. This update will void the warranty?

    4 is recommended for installed the OS from scratch in the new drive or could I use disk clone software? In this case, which?

    Thanks in advance.

    Currently, there is a problem with end users not being able to get this empty housing to recognize a M.2 WSSD drive added after delivery to the details of the laptop. Technically, the trying to jeopardize the warranty but who never stops the hard core of the valuation. So for the time being, until HP provides an answer as to what is happening with m2 slots, I do not recommend that you do the upgrade. If you want to go faster, I recommend that you install a SATA 2.5 inch SSD in place and place of the mechanical hard drive. Even that, however, will show warranty issues.

  • Star Wars edition an050nr: an050nr drivers

    Where can I get the drivers for Windows 7 64 for the portable edition Star Wars (15-an050nr)?

    When the drivers will be available? They will be available?

    Are there other sources for drivers that work?

    Am very pleased with the amount of data Windows 10 passes with no way to stop it.

    Hello:

    The last one that you listed is the security chip v 2.0 TPM which is not supported for W8 or earlier operating systems.

    So there is no drivers for this device, as they are only included in W8.1 and W10.  Having this device not installed will have no negative impact on the functioning of your laptop in W7.

    I'll post the links to drivers, according to me, you need in the order you posted the ID.  But first, install the smbus controller driver and restart.

    PCI\VEN_10EC & DEV_8136:

    3rd driver on the list...

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1 & PNid = 14 & PFid = 7 & Level = 5 & Conn = 4 & DownTypeID = 3 & getdown = false

    PCI VEN_8086 & DEV_3165:

    2nd driver on the list on the left side of the Web page...

    https://Downloadcenter.Intel.com/download/25510/Intel-PROSet-Wireless-software-and-drivers-for-Windows-7-

    Bluetooth driver for above wireless card...

    https://Downloadcenter.Intel.com/download/25319/Intel-PROSet-Wireless-software-for-Bluetooth-technology-for-Windows-7-64-bit

    PCI VEN_8086 & DEV_9D31 & PCI VEN_8086 & DEV_9D21 must also be installed by the smbus controller driver.

    PCI VEN_8086 & DEV_9D3A:

    FTP://ftp.HP.com/pub/SoftPaq/sp72501-73000/sp72884.exe

    PCI VEN_8086 & DEV_9D23:

    FTP://ftp.HP.com/pub/SoftPaq/sp73001-73500/sp73137.exe

    ACPI\HPQ6007:

    FTP://ftp.HP.com/pub/SoftPaq/sp71501-72000/sp71839.exe

  • Issue with reading limited edition of Medal of Honor war fighter and error DXGI_UNSUPPORTED error message.

    Original title: When I started publishing limited of Medal of honor warfighter I get a message "failed to create of D3D Device to at least 10.1 on graphics card Intel (r) with unknown driver. Error is DXGI_UNSUPPORTED

    I loaded the game on my laptop and when I try to start the game through the original I got the above message. I am looking for help resolve the error message.

    Hello
     
    Thanks for posting your question in the Microsoft Community forums.

    The description of the problem, I see you have a problem with the game Medal of Honor war fighter limited edition and error DXGI_UNSUPPORTED error message.

    I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.

    I suggest you try the procedure described in the article and see if it helps.

    You can check the link for more information:

    How can I tell if a game will work on this computer?
    Let us know the status of the issue after you perform the troubleshooting steps. If you need additional help or information on Windows, I'll be happy to help you. We, at tender Microsoft to excellence.
  • Store the Spanish: Star Wars in English

    A few comments. I am British and live in Spain. I suffer by your Spanish store with her Spanish dubbed movies that sometimes are not available in their original language. Despite the fact that you're the best option I have, the Microsoft store and Google game store had little English movies in Spain. I bought in the ecosystem Apple films last month and so far most of the purchases have been great, but the Star Wars we were horrible. Yes, the film is available in English, but you have committed the horror and betrayal Act to leave the famous Star Wars text roll all in Spanish with English subtitles. Terrible! My iTunes client is fully in English. My OS (Windows 10) is also defined entirely in English. In a digital market these things to note and Star Wars nerds like myself should not be exposed to the HORROR of a foreign language imposed on the Star Wars text roll. Please watch in solve this in the future if I get good English through and through.

    As a story aside, I think you should reconsider your encoding, your version of the movie is ok, but it lacks the detail I saw in other editions of HD film on my TV screen.

    You're talking about other users on these forums of users, no support or Apple iTunes.

    The film studio/holder of rights decides which language (s) and/or subtitles and/or features a particular movie has in the Bank of a country, not Apple. You can try to contact the rights holder

  • HP Star wars, model: 15-AN000: disable Intel Graphics

    Hello

    I have HP laptop special edition of star wars which has two Intel HD Graphics 520 and graphics Nividia 940 M.

    What I want is that completely disable the graphics card intel and using only nividia graphics card.

    First, I checked the bios to no possibility to do so, but found nothing.

    I've updated the bios and always this option isn't here!

    I want to completely remove chart intel from the Device Manager.

    Laptop model: 15-AN000NE

    OS: 10 64-bit Windows

    Help, please.

    Hello

    Please try NIVIDIA Control Panel as mentioned on the next post:

    http://h30434.www3.HP.com/T5/notebook-hardware-and-upgrade-questions/PC-is-using-Intel-graphics-instead-of-built-in-NVIDIA/m-p/5519758#M329296

    Please note: this consumes more battery and the machine may be hot.

    Kind regards.

Maybe you are looking for

  • Mac will not install usb software

    I recently bought a usb converter that would be able to let an ethernet cable to my mac and to activate the usb port, I had to install a program, it has been said that the USB should install it automatically, but there not later, I tried a helmet tha

  • iTunes Store recently added missing purchases

    Since the upgrade to iTunes 12.4.1 my purchases of song/album iTunes Store is no longer appear in the list "recently added". Individual tracks are also not appearing in 'Song' registration and my iTunes game does not synchronize these purchases in an

  • Questions "pin" to the new tab Page

    When I try to "pin" a top site of my favorites (drag and drop), by instructions given by Firefox, it is not pin. It is to open the page in a tab. I was wondering if anyone knew how to fix this? Additional info: I can not also pin the site open becaus

  • PCI-MXI-2 causes w/SP3 Windows XP Pro to freeze

    Here are the specifications of the test machine which is the gel with the PCI-MXI-2. Motherboard: C7P67 (supermicro) Mobo has no embedded video so I've tried three different cards PCIe... Currently installed: Geforce GT 430 DDR3 RAM: VS2GB1333D3 tota

  • Microsoft Visual C++ Runtime library runtime error, core program: C:\Program Files\MSN\MSN files\msn.exe

    Original title: Microsoft Visual Get the following message, then computer: "Microsoft Visual C++ Runtime Library Runtime Error, appeal of pure virtual function for files\msn.exe, R6025, core program: C:\Program Files\MSN\MSN. Anyone know what this me