2 1 modem from comcast networks, cable ISP using 2 linksys wrt routers

Similar Questions

• How to reset AirPort Extreme 10.11.6 OS? How to work with this pinhole? I'm trying to get rid of this flashing yellow light, which began after I installed a new modem from Comcast.

  How to reset AirPort Extreme 10.11.6 OS? How to work with this pinhole? I'm trying to get rid of this flashing yellow light, which began after I installed a new modem from Comcast.

  How to work with this pinhole?

  Usually a paperclip or toothpick or ball pen.

  Stick it in the hole and reset for about 10 seconds until the front led flashes quickly.

  How to reset AirPort Extreme 10.11.6 OS?

  The software method... Unlike the above material method... is to open airport utility and select restore default settings.

  

  Both methods take you to the same place.

  You can also read the manual...

  Reset to a base station AirPort FAQ - Apple Support

• How can I add a network from Windows XP to Windows 7 network. I use a Linksys WRT54G2 router.

  How can I add a network from Windows XP to Windows 7 network.  I use a Linksys WRT54G2 router.

  Try the method here...

  http://www.howtogeek.com/HOWTO/15247/complete-guide-to-networking-Windows-7-with-XP-and-Vista/

• Impossible to connect to the internet using dial-up modem cricket or network cable using the ip address

  tried cricket a600 but dormant, says it is connected but does not work, I tried modem on another computer and it market, tried by cable network using the ip address, same thing, connected but doesn't work, I tried install sp2, don't work, software reinstalled cricket but samething happens, please help

  Hi Aerostargt

  Your modem is compatible with Windows Vista?

  First of all check the compatibility:

  http://www.Microsoft.com/Windows/compatibility/

  Refer to this Article and follow the steps for your Windows Vista system for the issue of the Modem:

  http://support.Microsoft.com/kb/326681

  You can check these links for more information on troubleshooting network problems:

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  http://support.Microsoft.com/kb/956196

  After back and let us know if it helped to solve your problem.

  Thank you and best regards,

  R uma - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• How can I set Up Airport Express with an existing router/modem from the ISP

  I have a wireless modem/router ISP and I want to get the ability to use Air Print using a non-Airprint but the USB printer. I suggest you to connect the printer to the Airport Express A1392 Epson) via a USB port to enable the AirPrint features.  However, I guess the Airport Express must be an ethernet to the modem/router ISP connection and then use the Epxress airport more convenient than my wireless router.

  Issues related to the:

  1. do I need to turn off the function the ISP router's wireless when I plugged as stated above? So I wait.

  2. as the Airport Express only has one ethernet port I assume that I can connect my other ethernet connections using a hub 4 ports connected to the Airport Express Terminal.  It will be always possible to use other ports ethernet on the modem/router ISP as well?

  Doug

  I have a wireless modem/router ISP and I want to get the ability to use Air Print using a non-Airprint but the USB printer.

  You may have received incorrect information, because a non-AirPrint on the USB port on an AirPort Express Terminal... or any other router from Apple also printer... do not make the AirPrint-compatible printer.

  You want to continue nevertheless to check that this is true?

  The AirPort Express can connect to the network wireless router using a wireless connection... or... it can connect to one of the router's Ethernet ports using a wired Ethernet connection.

  Wired connections are always preferable wireless if possible for your Express.  Turn off the wireless router is not necessary if you want to connect to the Express using an Ethernet connection.

• I'm unable to connect to wireless modem, the message's problem is the network cable is unplugged got new cable still

  network cable unplugged wiundows xp

  I'm unable to connect to wireless modem, the message's problem is the network cable is unplugged got new cable still

  Hello Verashanley

  Since how long did begin?
  You have added a new software or hardware to the system?
  If the issue took place recently then you can try the system restore.
  How to perform system restore in Windows XP.
  If you have recently added anything to the system (hardware or software), then remove.
  If the system restore does not then check in Device Manager and verify that the network card is considered and no errors appear.
  To open Device Manager, click Start, and then click Control Panel. Click performance and Maintenanceand then click System. In the hardware tab, click Device Manager.
  Check the type of network card you have and that you try to update the drivers from the hardware manufactures Web site.
  Also, check the connection for the network adapter. Do you see any physical damage. When you plug the NIC saw all the lights on the network card lights up? If not, then you can deal with a hardware problem and need to contact the manufacture of the system and see about obtaining the card replaced.
  Let me know the results. Thank you.

• Why need a cable modem from a router can send and receive information to a computer?

  Why need a cable modem from a router can send and receive information to a computer?

  On Fri, 14 September 2012 17:14:59 + 0000, stuckfree wrote:

  Why need a cable modem from a router can send and receive information to a computer?

  A router is a device that connects computers (or other type of computer
  devices) to each other on a network and you can send files
  from one computer to the other. It does not connect to the internet, and
  you need a device called a modem vaguely to do this. The modem also
  connects to the router and allows the computers on the network
  (those connected to the router) to connect to the internet.

  However, note that there are some available devices that are
  router-modem combination. If your router is of this type, you do not have
  need a modem.

  Ken Blake, Microsoft MVP

• I look at apple tv in illinois, with service from comcast.  but, I'm moving to arizona for 3 months and cox communications is the cable operator. I always look at my apple tv?

  I look at apple tv in illinois with comcast as my ISP.  I'll be in arizona for three months.  Arizona cable provider is cox communications.  is it possible that I can watch apple tv on a big screen tv?

  As long as you have Wifi/ethernet your OK. Regardless of the name of the current provider.

• I have norton antivirus online via my ISP and I had to disable, because it comes with an error that says "cable not connected or missing network adapter" I use dial-up.

  cable not connected network adapter

  I have norton antivirus online via my ISP and I had to disable, because it comes with an error that says "cable not connected or missing network adapter" I use dial-up and do not use any type of router and I'm not on a network. I also tried to disable my network card & it still says the same error. I have an internal network card that came w / the computer (NOT a PCI one) and I wonder if there is a cord or a plug inside my computer that must be plugged. I made some changes on the internal hardware and might have missed an and I didn't have to open my Tower if it wasn't. It's a big hassle! Help, please!

  Hello

  1. Once you get the error message?

  2. do you get the error when you try to disable Norton anti-virus?

  3. are you able to access the Internet explore?

  Temporarily disable the antivirus on the computer running software and check if you are able to install the software.

  Disable the anti-virus software

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  WARNING: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

• AirPort Extreme can disappear from the network

  

  

  I have an airport Time Capsule 802.11ac 3 TB, implemented as my router, connected to a cable modem Comcast.  I also three units AirPort Extreme 802.11ac connected via an Ethernet cable and configure in Bridge mode.  The settings were all made with Apple AirPort Utility, using the default settings.  All devices are new, and have the latest version of the (7.7.7) package.

  My problem is that one of the SSA keeps disappearing from the network.  The AP utility shows all devices, but unity of the 'room' is still "missing in your network.  When I restart the device by unplugging the, the unit seems to work fine for a little while.

  Because the problem occurs on a unit, I think not that it is a question of ISP or OS.

  Has anyone else had a problem like this, and understand you?

  It is not uncommon.

  There is a real problem with apple DNS...

  What modem do you use?

  Actual spending brand and model please... It is probably not related, but it is useful to know the complete network configuration.

  Question I would like to change.

  1. your names are too long and contain spaces.

  Use any short names, without spaces and pure alphanumeric characters. Names must be less than 10 characters... all names... both network name.

  See Pondini for questions that arise with more long names... and that was before Apple changed network SMB.

  http://pondini.org/TM/C9.html

  2. the WAN port on the AC model TC and AE are not reliable.

  In bridge, what do you do better move the connection to one of the LAN ports...!

  3. you have an unreliable ethernet cord or if it is installed in the wall a bad Jack which is down to... This happens especially in that self installed ethernet... and even the ordinary electrician has problems... sometimes wrongly wired a pair of broken. You should test all ethernet correctly and make sure have full gigabit connections.

  4. use static IP via both a dhcp on the TC and AE reservation jumpered on the internet tab. Least IP moves the less work THAT DNS must do to stay.

  If you have still questions after.

• SOLUTION for your HP printer disconnect and/or constantly disconnecting from the network

  If you are having a problem printing, scanning or fax with any HP printer because of this be disconnected and constantly disconnecting from the network, here again is the fix!

  I thought that this all after several failed attempts with HP Support, my Internet access provider and various troubleshooting tasks including reinstall the HP software and more and more.  Well, through self teaching on internet and exhausting search for 6 months, I FINALLY thought to it.  OMG!  I'm a paramedic (not IT) and a little computer but far not an expert.  I have all of you here!  Nobody seems to have the answer, but I'm sure that I'm doing it to 97%.  Whatever it is, if it please answer and let me know that it worked for you!  :-)

  It doesn't matter if your printer is installed cable or wireless.  You don't reinstall your software, no recycling power of your printers or your router/Modem.  Your printer is unstable on the network and continues to log out or disconnect from the network it is NOT because the software is glitched, it isn't a firewall problem by saying, is not a router problem, is not a problem with your power cord, because most networks use a 'Beach' and IP addresses for security reasons This kind of "cycles" the IP addresses of the devices to reduce the risk of an attack.  A printer is not a threat, but the 'network' don't own human intelligence, so he does not know this.  Here are my step by step instructions on how to basically your printer address IP (static IP) instead of change back through a cycle so drop your printer on the network or disconnected.

  Funny, if you're someone who has had the elements in your print queue, they will not print, and you turn your printer off and on again and suddenly your print... well documents, join my club.  The reason it works is that when you turn on the printer, it starts with the same IP address before cycle.  If you are someone who is sitting there for a while and all of a sudden your printed documents without changing you something... it is because through the cycle of change of IP address, it hits your printers IP address and the network would allow him to print.  Not very funny, I know.  It took me forever to figure out why my printer would print sometimes, but not always.  Since I thought at this point, I can SCAN, PRINT, and use all the features of my HP software installed like HP, Photosmart Essentials Solution Center.

  On your printer, go to menu/Setup/network and press OK.  In the network menu, print a "network configuration page" so you can see the IP address and other settings of your printer.

  Now, back to the main menu on the screen of your printers.  Or you can go to your web browser and type the IP address using decimal numbers too and this will take you to the web page of your printers.  Choose: setup\network, then press OK.  Look for the IP settings and press OK. Choose "manual" instead of "automatic". Manually enter the IP address it as well as the default gateway that you can see the Network Setup page you printed earlier.  Note: If you manually set the IP Address of the printer, make sure that it is outside the range of your router's DHCP. Otherwise you might encounter a problem with IP addresses on your network duplicate. (If you don't know how to do this, write back and I'll explain).  Don't forget to click "save changes".  Now, restart your computer, and print just what you want.  :-)

  A trick I often use with DHCP network printers:
  In printers and faxes, right-click on the printer and select "Properties".  Click Add a new port.  Choose standard TCP/IP port configured for the host name of the printer. Read the host name of the network printer configuration sheet.
  
  Using my method means that you always connect to the printer even if its IP address changes (which can happen with the dynamic configuration). This does not jeopardize the security of your network.  It shows just your printer to stay put and stop traveling the highway of IP address.  :-)

  The DHCP range is the range of IP addresses that the router distributes automatically as devices to join the network.  The DHCP range is determined by the router and each brand has a range that is set at the factory (which can be changed by you).

  Default value for the DHCP of your D-link is 192.168.0.100 to 192.168.0.199.  Thus, outside the DHCP range est.2 a.99.200 a.254.

  Is a handy cheat sheet attached.

  You can change this interval by entering the router settings page - type the router's IP address in a browser, enter the login information and access the DHCP parameter area (varies depending on router, hunting around).

• Startup gets "Network cable unplugged" on (new) wireless mini-PCI card

  Repost in the previous topic was locked, but has not been resolved. Original post below, please see previous post for more details

  I recently installed a Netgear DG834GT wireless router and now have intermittent problems connecting my Tecra 9100. If the 9100 has been off for awhile (like overnight), when I restart I get always "Network cable unplugged" for the wireless connection. Reboot several times (anything from 3 upwards) I finally get connected to the router and everything then works fine for hours. Even a quick restart at this point (that is, once that the wireless adapter is connected) does not cause a problem, but as soon as I leave the stop of the machine during a time he fails again on restart.

  There are no errors in the event log.

  I am using wireless mini-PCI cards and have already updated to the latest version of the driver.

  Any ideas gratefully received, for now every morning is a 20 to 30 minutes of rebooting frustration trying to get my connection work.

  (Running Win2K professional)

  Hello

  I have the same problem if I stand for laptop and access point at the same time. If the access point is already in use, the connection is established shortly after. First the access point must establish a connection to the modem. Now the wireless connection is not available.

  I guess after the second reboot, the connection between the AP and the modem is already finished and you can use the network wireless successfully.

  Good bye

• Problems connecting to internet - says network cable disconnected, not sure I have the correct driver installed.

  Had a big storm - got the new modem.  but they said that my drivers where missing or damaged.  Downloaded Marvell Yukon of gateway - to the GT5432 model. Always says cable unplugged network. However, Bishop says peripheral device works correctly. Don't save: no update-unable to connect to the internet.  I uninstalled and reinstalled; rebboted, etc. - still nothing. It has a problem with the PCI connection - no driver, but I don't see anywhere to down load or know what to download. Oh and another adapter on - think 1394 - when I turn that on and off the wonder; It shows the signal for the 1394---400 and does not say his unplugged, but still can not connect to internet.
  The "old" computer to try to find information; noticed that said, unplugged network cable but it allowed me to connect to the internet. When I disabled the 'extra' adapter message there went, speed signal only at 100 than at the 'old' calculation is not any other PCI devices connection listed.

  I'm not sure of what continues.

  The 1st computer was working fine - then picked it up to move it to where it belonged to my office and that's when he went out-made no sense to me!

  Because you seem comfortable opening your computer, have you tried re - a corner of the map (with power off, remove the card and reinsert it into the slot, be sure to exercise static precautions if you are in an environment of low-hu7midity).  If there is an empty slot, you can also move the map Marvell to another location.  See the comments below.

  It's a long shot, because even if you did not provide the complete ipconfig output, the data that you have provided appeared to be normal, but...

  Open network connections (start > run > ncpa.cpl > OK)
  Right-click on the icon for your network adapter, and then select Properties
  You should see a screen like this--> http://screenshots.modemhelp.net/screenshots/Windows_XP/Network_Connections/Local_Area_Connection/Properties/General/Index.shtml
  Issues related to the:
  In the upper area, under 'Connect using' said 'Marvell Yukon 88E8039 PCI-E Fast Ethernet Controller?  If this is not the case, what does say?

  In the second box, what are the items are listed under "this connection uses the following items"?

  The only other thing I can think is that the Marvell Ethernet card was damaged in the same storm that got your original modem/router.

  *******************************************

  According to Gateway, the GT5432 has 4 card slots:
  A PCI Express x 16 (GUI)
  A PCI Express x 1
  Two PCI Conventional

  Your motherboard should look like this:
  

  Orange, top, connector is the PCI Express x 16.  You probably have a video card in this slot.

  The short white connector is the PCI Express x 1 connector.

  Two more long white connectors are the standard PCI slots.

  If I understand your installation, you should have the Marvell Yukon map into the slots of two down and your Agere modem on the other.  As long as you have the SMC1244TX PCI card, why don't just remove you the Agere modem or the card Marvell and insert the card CMS in one of the two PCI slots?  You are not using the modem and the working hypothesis is that the Marvell card does not work, so there is not much to gain by leaving a card in your computer.

  Download the user guide and drivers for the SMC here--> http://www.smc.com/index.cfm?event=viewProduct&localeCode=EN_TUR&cid=9&scid=51&pid=238 map

  Moreover, assuming that your open slot is the short PCI Express x 1 slot, you can buy another Ethernet card that will work in this niche: see--> http://www.newegg.com/Product/ProductList.aspx?Submit=ENE&N=100010064%20600016290&IsNodeId=1&bop=And&Order=PRICE&PageSize=100

  If I were you, I blow up the cheaper models and get the Intel EXPI9301CT $ 36 10 / 100 / 1000 Mbps PCI Express Desktop Adapter Gigabit CT.  Note that this is the same card with a similar name (with close to 400 customers) which sells for $29,94.  The price difference is because the cheaper "BLK" letters in the description, which means that it is "sold in bulk" and has no drivers, user guide CD or anything else in the box.  There are several negative comments from people who do not understand this difference and then had trouble finding the driver for the card on the Internet.

• Cannot establish network connection. Messages on the icon alternate between "Acquiring network address" and "unplugged network cable.

  Original title: cannot establish a network connection

  Very well, a computer can connect to the internet. Another computer using the same modem cable and fixed connection of the router (for example using the port adapter, not wireless) Wireless does not connect. I suspect that there are has some settings somewhere that are not correct. Can you tell me how to understand where is the problem?

  Messages on the icon alternate between "Acquiring network address" and "unplugged network cable. When I run troubleshooting this is what I get:

  Diagnosis of IP Configuration
  Invalid IP address
  Info	Zero (0.0.0.0) detected IP address
  action	Auto repair: renew the IP address
  action	Release the current IP address...
  action	Successfully published the current IP address
  action	Renew the IP address...
  error	Error to renew the IP address: the semaphore timeout period has expired.
  Info	AutoNet address detected: 169.254.225.103
  action	Auto repair: reset the network connection
  action	Disabling the network card
  action	Activation of the card network
  Info	Successfully activated network adapter
  Info	Zero (0.0.0.0) detected IP address
  action	Repair Manual: Reboot modem
  Info	AutoNet address detected: 169.254.225.103
  action	Auto repair: renew the IP address
  action	Release the current IP address...
  action	Successfully published the current IP address
  action	Renew the IP address...
  error	Error to renew the IP address: the semaphore timeout period has expired.
  Info	AutoNet address detected: 169.254.225.103
  Info	Redirect the user to support call

  WinSock status
  Info	All base service provider entries are present in the Winsock Catalog.
  Info	Winsock Service providers strings are valid.
  Info	Entry provider MSAFD Tcpip [TCP/IP] passed the loopback communication test.
  Info	Entry provider MSAFD Tcpip [UDP/IP] passed the loopback communication test.
  Info	Entry provider RSVP UDP Service Provider managed the loopback communication test.
  Info	Entry provider RSVP TCP Service Provider passed the loopback communication test.
  Info	Connectivity is valid for all Winsock service providers.

  Diagnosis of network adapter
  Network location detection
  Info		Using the Internet connection at home
  Identification of network adapter
  Info	Network connection: name = Local 2, Device network connection = Intel(r) 82562V-2 10/100 Network Connection, MediaType = LAN, type = LAN
  Info

  Ethernet connection selected

  State of the network adapter

  Info

  The network connection status: connected

  HTTP, HTTPS, FTP Diagnostic

  HTTP, HTTPS, FTP connectivity

  warn

  FTP (passive): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  warn

  HTTP: Error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  warn

  HTTPS: Error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  warn

  HTTPS: Error 12007 connecting to www.passport.net: the server name or address cannot be resolved

  warn

  FTP (active): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  warn

  HTTP: Error 12007 connecting to www.hotmail.com: the server name or address cannot be resolved

  error

  Could not make an HTTP connection.

  error

  Could not make an HTTPS connection.

  error

  Could not make an FTP connection.

  I found the problem (s), even if I am always left with a few questions.

  During this process, I have disabled the firewall, but that did not help. However, I noticed 'tweaks' accessed via the tab 'Advanced' in 'Microsoft Firewall' which looked like, they must be checked in order to access the internet. I checked these and reintroduced the firewall. After I got things working, I unchecked them and things still worked so I obviously don't understand what these parameters.

  The solution:

  (1) I have to go straight from the modem cable to the computer. I can't have a cable modem, router wireless, computer, even if using hard wire, and even if this same configuration works with another computer. Also, I can't use a cable length to go from modem to the computer. So, it seems to have had a problem of cable length. Power problem? Only connected to this computer devices are the mouse, the keyboard and the Ethernet. Would not this be fixed with an upgrade of the power supply? Or is it due to the quality of the Ethernet hardware on the motherboard? It's a Dell Vostro 200.

  (2) in back and forth between configurations while following the problem, you must think to unplug the modem to reset between each configuration. You may have stumbled upon the solution, otherwise he's not shot. Also, I unplugged the cable from the modem when you reset data cable - do not know if it was necessary. I wanted to limit the degrees of freedom that I had a lot, as it was.

• After a storm, my computer now says that a network cable is unplugged when plugged.

  original title: a network cable is unplugged

  There was a storm in our area recently and since then I can't access the internet.

  I have cable internet via my modem which is also connected via my wireless router.  Both the modem and the router properly.  To make sure, I bi-passe the router and the modem directly connected to the computer.  I also bought new ethernet cables.  None worked.  My ISP says that there may be a problem with my NICK so I uninstalled and reinstalled and it still doesn't work.

  NETWORK card: Realtek RTL8139/810 x Family Fast Ethernet NIC

  Modem: Aris Touchstone Telephony Modem

  Wireless router: D-Link WBR - 2310

  Thank you in advance.

  Hello

  It seems that the network card was damaged after the lightning.

  I suggest you to replace the card (if possible) network & check if the problem persists.

  Hope the helps of information.