200 MB ISP service with port 100 mb TZ100

Similar Questions

• L2l VPN between ASA with the IP address public and CISCO2911 behind the ISP router with port forwarding

  Hi all

  My apologies if this is a trivial question, but I spent considerable time trying to search and had no luck.

  I encountered a problem trying to set up a temporary L2L VPN from a Subscriber with CISCO2911 sitting behind the router of the ISP of an ASA. ISP has informed that I can't ignore their device and complete the circuit Internet on the Cisco for a reason, so I'm stuck with it. The Setup is:

  company 10.1.17.1 - y.y.y.y - router Internet - z.z.z.z - ISP - LAN - 10.x.x.2 - XXX1 - ASA - 10.1.17.2 - CISCO2911 - 10.1.15.1 LAN

  where 10.x.x.x is a corporate LAN Beach private network, y.y.y.y is a public ip address assigned to the external interface of the ASA and the z.z.z.z is the public IP address of the ISP router.

  I have forwarded ports 500, 4500 and ESP on the ISP router for 10.1.17.2. The 2911 config attached below, what I can't understand is what peer IP address to configure on the SAA, because if I use z.z.z.z it will be a cause of incompatibility of identity 2911 identifies himself as 10.1.17.2...

  ! ^ ^ ^ ISAKMP (Phase 1) ^ ^ ^!
  crypto ISAKMP policy 5
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  lifetime 28800
  isakmp encryption key * address no.-xauth y.y.y.y

  ! ^ ^ ^ IPSEC (Phase 2) ^ ^ ^!
  crymap extended IP access list
  IP 10.1.15.0 allow 0.0.0.255 10.0.0.0 0.255.255.255
  Crypto ipsec transform-set ESP-3DES-SHA 3rd-esp esp-sha-hmac
  card crypto 1 TUNNEL VPN ipsec-isakmp
  defined peer y.y.y.y
  game of transformation-ESP-3DES-SHA
  match the address crymap

  Gi0/2 interface
  card crypto VPN TUNNEL

  Hello

  debug output, it seems he's going on IPSEC States at the tunnel of final bud QM_IDLE's.

  What I noticed in your configuration of ASA box, it's that you're usig PFS but not on 2911 router.

  So I suggest:

  no card crypto OUTSIDE_map 4 don't set pfs <-- this="" will="" disable="" pfs="" on="" asa="">

  Then try tunnel initiate.

  Kind regards

  Jan

• HowTo: Define and provide a personalized service with disjoint / port range.

  I have a rv180 and I'm trying to implement a custom service that contains multiple ports two disjoint (some UDP some TCP), as well as a range of TCP ports. This has lead me to a few questions.

  (1) is it still possible to have a unique personalized service with disjoint ports? He'll just have to set several partial service for this?

  (2) is it possible to forward a port range? How to define a service with a range of ports, it is clear, but port forwarding interface table only allows me to select a LAN port side for any service. Is there a secret notation that I do here which will be just forward to the same port LAN side as port WAN-side - NAT effectively a transfer, but just for the selected service?

  Thank you

  Luke

  Hi Luke,.

  (1) Unfortunately, it seems that you have to implement services customized for each set of disjoint ports and then create rules of transfer for each custom port.

  (2) I'm not 100% sure that I follow your question, but I think I got the essential. Port forwarding will forward traffic on the specific port (service) of your wan IP public designated private IP (destination IP) address. You can restrict the access of calendar or IP ('source to users' - by the host or the beach). Because looks like you have several customized services, you must create a configuration for each service of port forwarding.

  I hope this helps.

  Best,

  David

  Please evaluate the useful messages.

• Problem with Port Forwarding (When PPTP is upward) in the WRT-160N

  Hello world!

  I'm looking for more help with Port Forwarding in my new Linksys router. I bought the daysago afew router and was pretty surprised when I discovered that there is no DD - WRT firmware is installed in it (the router was 100% NEW when I bought it). I downloaded latest firmware original and flashed Linksys file successfully.

  But I still have the problem (even that I was on DD - WRT firmware too) with the port forwarding for my DC ++ and Vuze (app from torrents): I wrote port forward for ports 49151 (for Vuze) and 4000 (for DC ++) to pass on to my desktop computer (IP 192.168.1.201) - I saw a post on this forum, that there could be a problem If you transfer to an IP address, which is within the local area of DHCP, so I forwarded to IP.201 (my local DHCPzone is 192.168.1.100-. 149) But does not forwardind (())

  What's wrong?

  My configuration:

  Router IP: 192.168.1.1

  PPTP (I my ISP)

  IP address: 192.168.226.127

  Default gateway: 192.168.226.2

  DNS 1: 192.168.1.1

  2 & 3 DNS: 0.0.0.0

  The IP address of the PPTP server: 192.168.226.2

  User name: *.

  Password: *.

  _____________________

  Simple Port Forwarding:

  Name of the external port application port internal protocol for IP address Enabled

  Vuze 49151 49151 times checked 192.168.1.201

  DC 4000 4000 checked two 192.168.1.201

  As you mentioned in your post that your ISP has provided you with a PPTP connection with an IP address: 192.x.x.x. The IP address that is provided by your ISP is in a private beach, and if you try to transfer all the ports on your router, it will not work, as long as your ISP modem is blocking this port. If you need get a public IP address from your ISP.

  As you get Private IP of your ISP, if this connection is called as NAT behind NAT and your Modem behaves like a router.

  So now you have 2 options, get the public IP address from your ISP or change the type of connection.

• Change the ISP service - Sonicwall TZ 105 W

  We change ISP service and get a new direct IP block.  None of my internal IP addresses change.  We organize our own Web site and e-mail.  Right now I've got round a T1 shared (with phones) and a DSL line to do load balancing.  My question is, it would be easier to do a factory reset and reconfigure from scratch or simply by changing the settings on the WAN interface IP and the public on the objects of my IP address would be easier?  Thanks in advance!

  Personally, I would do a Factory Reset to just save yourself any pain that might come from any left on configs since IP addresses and the previous rules.

  You could go and change everything if you want if you have a simple configuration. Remember for each policy NAT that there is an access rule.

  Thank you
  Ben D
  Reference Dell SonicWall
  #Iwork4Dell

• VWC plugin using sdk 5.1 is broken if running on the web client 6.0 with port 9443 - out could not connect to the Web Client vSphere. Contact your administrator to resolve this problem.

  We did a vwc with sdk 5.1 plugin, now, we want to make it work on the web client 6.0. before the race, we have changed the MANIFESTO. MF and services-config. XML responses such as the following:

  2 important reminders for your plugin 5.5 is compatible with the Web Client 6.0

  After that, we deployed our plugin on web client 6.0

  If access us using the URL with port: https:// < ipaddress >: client/vsphere-9443 /? csp, our plugin arises, our plugin function is also ok.

  If access us using the URL without port: https://< ipaddress > / vsphere client /? csp, our plugin is present, the function is broken (error occurred when flex user interface by calling the java service: "Could not connect to vSphere Web Client.) Contact your administrator to resolve this problem. »).

  Thank you very much

  Please change the CHANNEL_URL in your proxy classes to use 'amf' instead of 'amfsecure '.

  private static const CHANNEL_URI:String = "/" + YOUR_MODULE.contextPath + "/messagebroker/amf"
  

  This should solve your problem.

• Company that multiple instances cannot start with port set to 80

  I have three instances: main forum is for cfadmin site, then, two are my websites.

  cfusion-> site cfadmin - port http < white - > remote port 8014 - host localhost - cluster no

  cfusion2-> site 1 - port 80 - remote port 8012 http - host localhost - cluster no

  cfusion3-> 2 - port 8501 http site - remote port 8011 - host localhost - cluster no

  cfusion2 does not start and the instance Manager page refreshes just without message, and there is no log system or cf with errors. I use the Chrome browser, I gave up on Internet Explorer (event after adding the sites to the safe zone).

  I then configure the third-party site using WSCONFIG in the hope that it will use cfusion3 server but on the contrary it is selected automatically cfusion.

  I could really use some help here. Thanks in advance.

  Well, I received my case running and each with its own windows service. More I don't get the blank page of death, and I did not manually change the configuration files in order to make this work.

  When CF instances are created, it creates a copy of the file cfusion for himself. and so in itself, there's also a runtime/bin folder that contains the WSCONFIG tool. So rather than create a CF Connector for my IIS sites using the main cfusion WSCONFIG tool I had use every tool within each instance. Many of you probably already knew that.

  It was recommended by Anit Kumar to activate the embedded server so that port 8500 is busy before creating instances so that the newly created instances do not automatically pick up port 8500.

  Thanks to Alexis who helped every step of the way and that got my server correctly setup.

  For anyone doing a new installation on windows server, be sure to run the installer with administrator rights. In addition, make sure that your cf installation folder has the appropriate permissions. Initially, I gave everyone full control of my installation folder, then after its installation and work I started to follow the recommendations of Peter CF 11 Lockdown Guide permissions. follow http://www.Adobe.com/content/dam/Adobe/en/products/ColdFusion/PDFs/cf11/cf11-Lockdown-GUID

  Adobe CF, could you guys add some stuff and how simple instructions on the page instance in CF Administrator Manager? He must know that bodies have their own WSCONFIG tool and should be used for the planned sites. Also, I think that additional instances should start with port 8501, 8500 should be left alone for the integrated server option. This could avoid installation problems. Oooh, also if possible in the instance Manager add an action button that opens its own WSCONFIG tool. Action can be called "add a website".

• a service with 2 instance (no cars)

  Hi all
  
  I'm trying to understand why a service has 2 instances when I don't have a CAR. My DB is on a stand-alone server, but it displays 2 instance. This causes no problems, but while testing something I came across this and I wanted to clarify what is happening here... Here is the out put. I'm on 11.2.0.1 and see it on 10g as we... I get the part when he says READY is a dynamic registration and when his UNKNOWN, is a static record. But I only have a single listener...
  
  Here's the listener.ora file
  

  ADMIN_RESTRICTIONS_LISTENER = on
  LISTENER_ORCL =
    (ADDRESS_LIST =
          (ADDRESS =
            (PROTOCOL = IPC)
            (KEY = ORCL.WORLD)
          )
          (ADDRESS=
            (PROTOCOL = IPC)
            (KEY = ORCL)
          )
          (ADDRESS =
            (COMMUNITY = SAP.WORLD)
            (PROTOCOL = TCP)
            (HOST = hostname)
            (PORT = 1535)
          )
    )
  STARTUP_WAIT_TIME_LISTENER_ORCL = 0
  CONNECT_TIMEOUT_LISTENER_ORCL = 10
  TRACE_LEVEL_LISTENER_ORCL = OFF
  SID_LIST_LISTENER_ORCL =
    (SID_LIST =
      (SID_DESC =
        (SID_NAME = ORCL)
        (ORACLE_HOME = /oracle/ORCL/112_64)
      )
    )
  ADR_BASE_LISTENER = /oracle/ORCL/saptrace

  and this is the status which shows 2 earpiece

  lsnrctl status LISTENER_ORCL
  
  LSNRCTL for HPUX: Version 11.2.0.1.0 - Production on 30-MAY-2012 18:26:39
  
  Copyright (c) 1991, 2009, Oracle.  All rights reserved.
  
  Connecting to (ADDRESS=(PROTOCOL=IPC)(KEY=ORCL.WORLD))
  STATUS of the LISTENER
  ------------------------
  Alias                     LISTENER_ORCL
  Version                   TNSLSNR for HPUX: Version 11.2.0.1.0 - Production
  Start Date                22-MAR-2012 22:03:30
  Uptime                    68 days 20 hr. 23 min. 8 sec
  Trace Level               off
  Security                  ON: Local OS Authentication
  SNMP                      OFF
  Listener Parameter File   /oracle/ORCL/112_64/network/admin/listener.ora
  Listener Log File         /oracle/diag/tnslsnr/hostname/listener_ORCL/alert/log.xml
  Listening Endpoints Summary...
    (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(KEY=ORCL.WORLD)))
    (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(KEY=ORCL)))
    (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=server.com)(PORT=1535)))
    (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=xx.xx.xxx.xxx)(PORT=1535)))
  Services Summary...
  Service "ORCL" has 2 instance(s).
    Instance "ORCL", status UNKNOWN, has 1 handler(s) for this service...
    Instance "ORCL", status READY, has 1 handler(s) for this service...
  The command completed successfully

  In fact, you have 2 Oracle Net services with the same instance.

  Reason for this is that you have:

  1 instance of static record with earphone ("status UNKNOWN") because of listener.ora next section:

  SID_LIST_LISTENER_ORCL =
    (SID_LIST =
      (SID_DESC =
        (SID_NAME = ORCL)
        (ORACLE_HOME = /oracle/ORCL/112_64)
      )
    )
  

  2 by default, dynamic record instance with earphone (status "READY") because most likely you have instance to the LOCAL_LISTENER parameter local listener on port 1535.

• Service Console port group

  I have a test box that I started to use a VLan tagging with. Unfortunately, I forgot to place the service console port group. Is there a way to change the port group to service the console kvm CLI console?

  You can define a VLAN with command portgroup esxcfg-vswitch-p - v vlanid

  ---

  VMware vExpert 2009

  http://blog.vadmin.ru

• My iphone shows no service with all networks in Egypt also sometimes works and all this happened all of a sudden

  My iphone shows no service with all networks in Egypt also sometimes works and all this happened all of a sudden

  If your provider supports iPhone

  I'd look for an update to the carrier

  Settings - carrier - it will pop up if available

  And if there is none then speak to the carrier a replacement of the SIM card

• Having problems with ports USB 3.0 in computer option H8 - 1010 T

  Well, I bought the option USB 3.0 ports on top of the computer on the computer mentioned in the Thread object and I have problems with them.

  I tried plugging USB 2.0 devices in these two ports to "test" to see if they work, yet I am not able to get them to work with USB 2.0 devices. USB 2.0 is not compatible with USB 3.0 ports? Or I'm doing something other 'evil' here?

  Unfortunately, I do not have a USB 3.0 device to plug USB 3.0 ports to make sure that it is certainly a problem with ports still.

  The device in question I've tried in the USB 3.0 ports is a Microsoft Wireless Mouse 6000 wireless receiver. If the ports are not connected correctly, I would have assumed that the wireless receiver would have "blown" when I plugged it in, but it still works very well.

  USB 2.0 devices are not compatible with USB 3.0 ports? I know that USB 3.0 devices are backward compatible with USB 2.0 ports (I have a friend who is in this situation), but I also thought that the opposite was supposed to be true as well. Am I wrong?

  @William

  Check out this thread, seems to be the same problem you are having.

  http://h30434.www3.HP.com/T5/desktop-hardware/USB-3-0-ports-on-Pavilion-HP8-1070t-not-working/m-p/792857/highlight/true#M35248

• Why my MBP retina nine come with only 100 GB against 120 GB as shown. (He says 20 GB has been used, but I just bought the laptop) is enough space of 100 GB. I'm not a gamer or anything like that. Just need the computer for College

  Why my MBP retina nine come with only 100 GB against 120 GB as shown. (He says 20 GB has been used, but I just bought the laptop) is enough space of 100 GB. I'm not a gamer or anything like that. Just need the computer for College

  How to report the storage capacity - Support Apple OS X and iOS

  If you bought the Apple MBP, you have 14 days to swap for a most appropriate mac.

  If bought from a different dealer, you will need to contact them about the Exchange / return policy.

• Web services with customer LV

  A typical approach to web services to access the host (a cRIO incorporated, for example) by using a client running in a browser with JavaScript.  All those put in place a LabVIEW client that calls the web services on the host computer?  How this could be done?

  I have a cRIO with a RESTful web service work and I can access it with my browser.  It works very well.  Now, I want to access the same service using a LabVIEW client... Or I could write my own customer by BT if I new how to register the service with .NET, which I did not.  So, it's a fact that LV can be used to create a web service client.  I'm looking to better understand how it can be done.

  The native TCP VIs can perform HTTP requests and call the methods of Service Web LabVIEW (http://zone.ni.com/devzone/cda/epd/p/id/3153 or http://decibel.ni.com/content/docs/DOC-2230).  Using these screws, you can create a customer of LabVIEW.

  Alternatively, you can use an ActiveX control to the browser with the Navigate2 method to call Web Services:

  

  WSDL files are generally used for Web Services using the SOAP Protocol (Developer Zone Tutorial: LabVIEW using SOAP Web Services call).  I know that it is possible to do the same for a RESTful Web Service (LabVIEW deploy services RESTful web), but I don't have any information on how this is done with a simple Google search in addition, it seems that most of the other public forums has rejected the idea, because you just need to build an HTTP request to call a web method.

• Push service with wifi

  HII,

  I'm a programmer and I have developed an application that receive the push. Problem:
  I can´t receive push with my application. I don't have plan data and from what I've seen in all the forums may not receive push. But why Blackberry Messenger, whatsapp, facebook works?
  I have only Wifi available.

  Thank you

  Push will work on all devices, Wifi, but for OS 7.1 you need a BlackBerry service with your carrier plan. Having this plan will push down the necessary maintenance book data so that your device can connect to the infrastructure of the Push. Similarly, social media like BBM on BBOS 7 services also use the service book for the data connection. They may work on wifi, once you have the data in the maintenance book. BBOS<= 7.1="" also="" allowed="" for="" a="" social="" media="" plan="" that="" pushed="" down="" social="" media="" (bbm/facebook/etc)="" service="" book="" data="" to="" enable="" those="" services,="" without="" pushing="" down="" a="" full="" data="" package.="" so="" it's="" entirely="" possible,="" even="" quite="" common,="" for="" someone="" to="" have="" access="" to="" bbm="" over="" cell="" and="" wifi,="" without="" having="" push="" or="" regular="" data="" connectivity="" available="" for="" other="">

  BlackBerry 10 has a completely different architecture without any idea of a maintenance book. Push and BBM will work over WiFi without special plans.

• 'Web Deployment agent service' using port 80.

  Hello community,

  After I uninstalled ampps (alternative to Xampp) and re installed, I get a message that port 80 is used by another application.
  I discovered in "Windows Task Manager" than (NT Kernel & System) was the culprit. After Googling further concluded that "Web deployment agent service" use port 80.

  C:\Program Files\IIS\Microsoft Web Deploy\MsDepSvc.exe' - runService: MsDepSvc

  What I've done so far was out of "MsDepSvc.exe" by spacing it epSvc.exe MsD.

  I want to know is why IIS start using port 80. Because ampps do not complain about it before!

  And what is the solution. How can I change the port for IIS?

  Thank you!

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home