Company that multiple instances cannot start with port set to 80

Similar Questions

• Error message at startup: "cssauth.exe instance cannot start due to an initialization error" and also unable to open help and the file

  Original title: cssauth.exe instance cannot start, help and Support of file disable

  Whenever I connect to my windows XP, it still says cssauth.exe instance cannot start due to an initialization error and I could not open my file help and suppot. Please help me. Thank you before

  Hello

  1 how long have you been faced with this problem?
  2. don't you make changes on the computer before this problem?
  3. What is the brand and model of the computer?
  4. who help and support files are you referring to?
  5. what exactly happens when you try to open it? You get the error message?

  cssauth.exe is related to the Client Security Solution.

  Step 1: Try disabling startup cssauth.exe in the configuration of the system.

  Here's how:

  1. click on start > run.
  2. type msconfig and press ENTER.
  3. click on the Startup tab.
  4 locate cssauth.exe, and clear the check box for this.
  5 restart the computer and check for the issue.

  Step 2: If you still get the same error at startup then perform the clean boot on the computer.

  From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".

  Reference:
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. click on start and then click Run.
  2. type msconfig and click OK.

  The System Configuration Utility dialog box appears.

  3. click on the tab general, click Normal Startup - load all services and device drivers and then click OK.
  4. When prompted, click on restart to restart the computer.

  I would also ask you to contact the manufacturer of the computer because the problem is with the client security software that is provided by them.

• My Dell all-in-one 962 stopped printing all of a sudden. The error messages are that the computer cannot communicate with the printer.

  My Dell 962 All In One Printer suddenly stopped to print. I get an error message that the computer cannot communicate with the printer. The error message suggests that I unplug and plug back the power plug and the USB cable to the printer and make sure that there are no restrictions of firewall to the printer. I did what was suggested and still no printing. I have resinstaled the printer from the CD software, I got with the computer and also installed the latest driver using the software of the software upgrade wizard.

  and also installed the latest driver by using the Software Update Wizard software.

  That would not have been the best idea... but it is unlikely that the cause of your immediate problem.

  The next thread does not make much sense to me, but it describes a situation similar to what you described and the proposed solution is supposed to have worked.  Try it and see--> http://en.community.dell.com/support-forums/peripherals/f/3528/t/19483019

  I suspect that what really happens is that the driver has become corrupted.  In many cases, simply reinstall the driver is not fix things; you have to clean the old corrupt driver before installing the new.  Thus, it is more likely that the part "Uninstall" the related response is what is helping rather than playing with services... but go ahead and follow these directions, just in case.  In fact, I suggest that you run under first antimalware scanners before following the tips in the above link.

  If I had not found the link above, that's what I would have suggested (whichrequires that you have Windows XP):

  Often, but not always, the symptoms you describe are caused by a corrupt print job stuck in the queue or a damaged printer driver.  However before you clean things up, on general principles, that you can download, install, update and run full scans with each of these two free programs.

  MalwareBytes AntiMalware

  SUPERAntiSpyware

  Use the free version, not the free trials of "pro" versions  Pay attention during installation uncheck any prechecked boxes that would install some additional third-party programs.

  Do not run the scans at the same time.  Each scan will take a while.  Start one and go do a non-it chore.  Once the scan is finished, leave the program to deal with anything it finds.

  Once done, you can keep or uninstall programs, or both.  If you keep SAS, I suggest to change its default setting does NOT automatically when Windows starts.

  Uninstall all software from Dell to control panel > Add / Remove programs

  Download Microsoft Fixit 50126 impression: http://go.microsoft.com/?linkid=9662904

  Close all running applications (anything with an icon on the taskbar).

  Run the Fixit routine.  Note: The routine Fixit has two modes, light and complete.  It will run in full mode when you check the box "Reset the spooler to print on values."  This will remove all printers, so if you have any other printer installed, I recommend running the Fixit in full mode.  If you have other printers and you do not (necessarily) want to reinstall them, run the Fixit in light mode (box unchecked).  This may work anyway.  You must restart the computer after you run in full mode; you need not restart after the Chase mode.

  After the Fixit has executed and you have restarted if necessary, make sure that the printer is disconnected from the computer and run the installation software.  You will be asked to connect the printer to a suitable place.  You can use the CD that came with the computer or download the software here (which is relatively hard to find, the claims of the main page of the 962 product support it cannot find the drivers)--> http://www.dell.com/support/home/us/en/19/Drivers/DriversDetails?driverId=R89490

• When I turn on my computer, he told me that the program cannot start because ash.dll base is not available in my PC.how I can solve it this issue.

  Thank you for allowing me to ask my question.

  My question is about the message poster on my PC window indicating that the program cannot start because ash.dll base is missing in my PC.

  So how I can solve this issue.

  This program is for AVAST ANTIVIRUS

  Ash.dll is usually associated with an infection.

  Install/run these two free utilities

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  http://www.Malwarebytes.org/products/malwarebytes_free/

  It could also be the case that Avast detected & removed the infection but left a remnent, this being the case closely check the entries in the msconfig Startup tab

• Apex listener start with port 8080

  Hi all
  If I want the listener of the apex to start with port 8080.How can I do this?
  
  
  -bash-3, $ 2 java-Dapex.images=/home/tomcat/apache-tomcat/webapps/ROOT/i-Dapex.port=8080-jar apex.war
  NEWS: Check out: /apex_4.0.2/apex.war
  See: ' java-jar apex.war - help' for a full range of configuration options
  INFO: Extraction to: / tmp/apex
  SEVERE: method java.lang.System.console with signature (Ljava.io.Console); not found.
  java.lang.NoSuchMethodError: java.lang.System.console method with signature (Ljava.io.Console); not found.
  at ___embedded.___EntryPoint.apexImages(___EntryPoint.java:104)
  at ___embedded.___EntryPoint.main(___EntryPoint.java:91)
  
  What can be the problem...
  
  
  
  
  Best regards
  
  Rafi.
  
  Published by: Rafi (Oracle DBA) August 12, 2011 03:36

  Hey Rafi,

  great to hear you got it working now!
  Please mark this thread as a response if your problem is resolved.

  Thank you

  Udo

• e9280t cannot start with the USB 3.0 card (tried several providers) new version of BIOS e9280t necessary

  Hello...

  I bought a new e9280t year last on the HP site complete with 9 GB of memory (now 16), Blu-ray/DVD writer & reader, tuner TV digital Hauppauge, ATI Radeon 4850 video card bi-ecrans, etc... Since then, I've added more memory and a Firewire 400/800 3 card. His running Win 7 Pro (sp1) and the BIOS is v5.29.

  I bought an external drive to USB 3.0 WD (3 TB) and a StarTech USB 3.0 card (Amazon.com). After installing a USB 3.0 card, the system would be powered on for a second then die and then do it again a few seconds later and the cycle continues until the power cord was pulled. Then, I pulled the USB 2.0 card and tried again only to have the same results. The only cards that remained in the system during the trial was the ATI card and the TV Hauppuage card.

  Thinking that the problem was with the USB 3.0 card, I bought another provider (Rocketfish of BestBuy) and installed. The same problem as with the other card USB 3.0, the system does not start.

  No software driver or other changes have been made to the system before installation tent (according to the vendor's installation instructions).

  Given that all failures occur during the power first sequence and cards have been tried with and without power tied to them, that the problem cannot be fixed with an upgrade of the BIOS for the motherboard of TRUCKEE. I could be wrong, but I'm going on 30 years of experience of material as my framework for this review.

  If anyone else has this same problem, it would be good to rally them around and see if HP notice us.

  Thank you

  Norm

  I upgraded my power supply 650w (thermal take) and it all works - USB 3 controller (Koutech Dual Channel SuperSpeed USB 3.0 PCI Express Card (2 x internal) model IO-PEU232) - he also has a SATA power connector, but it works very well with just a power bus.
  -also updates card reader (put it in the 2nd DVD Bay): internal Koutech IO-RCM630 Multi-in-1 USB 3.0 SuperSpeed Front Panel card reader with a USB 3.0 Port (3.5 ")

• Portege Z930 cannot start with installed RAM module

  My laptop Toshiba Portege Z930-108 has stopped booting with any module of RAM installed in the support.

  If I remove RAM module, laptop computer starts and works fine, but if I install any module of RAM (4 GB 1600 original or a new 4 1600 CL9 or 1600 8 CL11) the computer cannot start.

  The screen stays black and power led flashing two green and two orange and a few seconds later, 3G indicator also on blue.

  This is the only problem I have with this computer, but it's strange.

  I updated the BIOS to the latest version and the problem is not resolved.

  I tried to reset the hardware (http://aps2.toshiba-tro.de/kb0/TSB3B03J90000R01.htm), also I tried to reset the equipment with power button 30 seconds without battery but button without success.

  Any idea on this problem of strage?

  Kind regards
  Lito.

  I guess you used bad RAM or not fully compatible modules.
  It's the only plausible explanation.

  I recommend you to order the RAM modules recommended by Toshiba that are:

  4 GB DDR3 - 1600 PA5037U-1M4G

  2 GB DDR3 - 1600 PA5037U-1M2G

• Server instance cannot start because the Weblogic domain integrated

  Hi all
  
  I use the new version of Jdeveloper. IE 11.1.1.6.0. I get the error "The Server Instance cannot be started because the integrated Weblogic domain has not been built with success." whenever I try to run a page simple jspx.
  
  Please someone help me.

  Hello

  Welcome to OTN.

  You can try the following.
  1. close JDev.
  2 remove the DefaultDomain file under your [url http://tompeez.wordpress.com/tag/system-folder/] file system.
  3. launch JDev
  4. run your jspx page.

  Arun-

• Re: Cannot start with driver USB Satellite A40-271

  Hello

  I have a Toshiba Satellite A40-271 and there was a problem with windows and I can not start, so I decided to start with linux. I tried once with a cd and it worked perfectly, now I try with a usb flash pen and it does not work.

  Can someone help me?

  Hello

  As far as I know the Satellite A40 is very old model laptop and I think that the BIOS does not support booting from a USB flash memory
  I know it of possible to start the USB FDD drive

• Satellite Pro A200 - cannot start with new RAM

  I have two of these laptops, both purchased at the same time.
  I upgraded to 320 GB hard drive and tried to move the RAM to 4 GB as the spec States can be made.

  I used the recommended type of RAM, but the computer does not start with two RAM modules inserted. If I remove one of them, the laptop boots! I thought that I update the BIOS but found the only version available on the download web site is the same as I.

  Does anyone have an idea what could be wrong?

  What RAM you bought? I think that the modules are not compatible or your chipset does not support the 4 GB.
  Check it with CPU - Z!

  You could test the RAM with Memtest86 ([www.memtest86.com]).

  I doubt that a BIOS update will solve the problem. A more recent BIOS does not change the decision-making ability and/or supported RAM.

• Cannot start with any disk

  Hi all,

  Could someone help me because this problem is crazy drivinme!

  They gave me a pc less hard drive, disk and dvd - so I therefore sat last night and put put in a fresh new hard drive and a new drive, then I was ready to go and put XP home on.

  This is a not to do as he would entangled initialize not he manages to come up with either Grub error 17 or 22 so I double checked all settings of the bios as so far, I'm aware that I don't think I missed something... so I tried to start with - 3 other drives xp, ubcd4win, and a startup disc patition magic - and guess that soon one start you the pc it reach not to start and stay on the screen with loading GRUB error 22 Please wait please help!...

  Concerning

  GT4U

  Hi all,

  This problem was a simple solution using startup disk wizard patition and rebuild the M.B.R - master boot record.

  Concerning

  GT4U

• Cannot start with the USB on my hp proliant microserver, why?

  Hello!

  I had a few problems to install esxi 5.5 on my hp proliant microserver... USB keyboard, but I solved that by plugging another keyboard, an old labtec keyboard.

  Seems esxi is not compatible with logitech g510... BUT I have another problem. My server does not start with my installation of esxi usb key longer. It was also like that before I changed the keyboard, so this isn't the issue. Server starts fine and then I get the message: "'remove the disc or the media, press any key to restart" "

  It worked fine a few days ago. The usb boot works OK on my Hp workstation...

  I have a windows server 2008R2, installed on the server, but the usb boot worked fine when this OS is installed... So nothing has really changed, he just stopped wanted for a startup with USB... I loaded the default bios setting... IM lost here please help!

  IV ' e OK installed esxi 5.5 via USB stick

  Follow this link to get the usb boot: http://www.tinkertry.com/rufus-takes-2-minutes-to-create-a-bootable-usb-flash-drive-for-esxi-installation/

  Don't know yet why this work, but I'll know!

• Why the Pan & Zoom Tool cannot start with the frame using photos

  I used the animation panning and zoom in Microsoft Movie Maker - and want the same ease of use in any other program (I find that he does a great job of a soundtrack placement and text/image) see options from the menu below...   I purchased Premiere Elements after watching a short video of the pan & zoom tool - but now I'm trying to use it it falls way short.

  Y at - there a way for me to select the whole photo as the starting frame – in the screenshot below that frame 1 will extend to the entire photo, so I'm going with a cropped image.  I want the full Frame of the photo and then be able to zoom and pan in the direction of faces - while I can still do it with the cropped image I lost part of my picture and the context it provides.

  The Microsoft Movie Maker - very easy options |              Limitation of the first of 13 elements start with the complete picture frame

  

  Found a good explanation of this question in the forum first elements

  Pan and zoom tool

• PXE cannot start with XPS 13 9350

  My company has recently had to buy a few new laptops due to expansion, and the XPS 12 9333 was no longer available, so we sold the XPS 13 9350 instead, having received assurance that it is the same system and everything will be supported as it was with the XPS 12. I ran through the normal steps in the BIOS to ensure a compatibility PXE boot (disable Secure Boot, select Startup inherited, etc. options), but when I hit the F12 key to try to perform a network boot I don't see the option in the start menu. All I see is Windows and the Samsung SSD Boot Manager. Someone at - it else here had this problem and managed to resolve it? We use Ethernet USB21000S2 StarTech adapters suggested, that Dell sold us.

  Trying to deal with their customer support has proven me why I HATE DELL with a passion. Advised to my boss to go with ASUS or Lenovo, but she wanted to go with Dell because of a long-standing commercial relationship. You can not get someone who speaks clear English on line, you will need to explain your problem 10 times before you finally get someone who is able/willing to help. No one seems to understand what I meant by PXE boot or told me he is not allowed on their laptops.

  Hi Rick,

  Thanks for the reply. We have tried all the suggestions that you pointed out, but nothing has been able to get the Startech adapter to work. You don't know if it is related to two USB 3.0 ports or not, but it seems that the Startech USB21000 does not work with the Dell XPS 13 9350.

  I had to buy an adapter Ethernet USB - C, and which went through without any problems. About 1/2 also took time to the Startech adapter took which was a pleasant surprise.

• Satellite Pro P300-19 q - cannot start with a new memory

  So, I want to add 2 GB of RAM to 2 GB existing. I use Windows 7 64-bit. In the BIOS, I see 4 GB of memory, but windows won't start.

  When removing the old memory and leaving the new, the computer isn't even strats. Some info:
  Old memory - Samsung M4 70T5663QZ3-CF7 2 GB DDR2 - 800 DDR2 SDRAM (6-6-6-18 @ 400 MHz) (5-5-5-15 @ 333 MHz) (4-4-4-12 @ 266 MHz)
  New memory - Spectek DDR2 2 GB PC6400 800 MHz 200 pin

  So, what's the problem? And what can I do?
  Thank you

  Hello

  Theoretically, it should be possible to use 4 GB in this notebook.

  The new RAM is the manufacturing of Spectek. This production does not for me. For me, looks not dear noname module.

  I always use Kingston modules to upgrade my laptop. I've never had any problems with these modules, so you should try it to.
  I think that the new module isn't compatible with your laptop.