2911 + VPN + Acl client

Similar Questions

• Easy VPN - acl

  Hello

  There is an "acl" parameter that is not clear to me, it is configured at customer site:

  Crypto ipsec VPN ezvpn client

  connect auto

  Cisco key band EASYVPN

  client mode

  peer 10.0.0.1

  username cisco password cisco

  xauth userid local mode

  ACL 101

  Everything that I added to the ACL 101 tunnel is always present. I found a description:

  Step 6

  ACL {name - acl |}                 ACL-number} Example: Device (ezvpn-crypto-config) # acl acl-list1

  Specifies several subnets in a VPN tunnel.

  "Specifies several subnets in a VPN tunnel".  -what it means, source?

  I tried to use this setting, and I added the access list:

  access-list 123 allow ip 10.10.10.0 0.0.0.255 host 20.0.0.20

  access-list 123 allow ip 50.50.50.0 0.0.0.255 host 20.0.0.20

  where 10.10.10.0 and 50.50.50.0 are source and 20.0.0.20 is the destination.

  When I ping with source 10.10.10.3 (physical int) for 20.0.0.20 - numbers of BA & desc packages grows.

  but when I ping with source 50.50.50.50 (int loop) for 20.0.0.20 - I see that it wasn't to push into the tunnel.

  Could someone explain how the work parameter and for what is it?

  Thank you

  Hubert

  Hubert,

  Ref:

  http://www.Cisco.com/en/us/docs/iOS-XML/iOS/sec_conn_esyvpn/configuration/15-2mt/sec-easy-VPN-rem.html

  in client mode several subnets are not supported, nor what they sense.

  You specify what internal subnets of announcement to the server that are configured behind this device.

  In client mode, the server sees only the assigned IP address.

  M.

• AnyConnect and SSL - VPN without client

  Are there problems in running Cisco AnyConnect and SSL - VPN without client side by side?

  I am currently looking into adding features for an ASA AnyConnect who currently set up to operate without SSL - VPN client. The system without client is not removed. I don't know how to set it up, I wonder if someone has already set up this or if there is no problem with this Setup?

  Hi Daniel

  It's a little complicated if you want a granular authentication and authorization, but it works.

  I'm running an ASA with IPSec, SSL Client and clientless SSL.

  Each of these virtual private networks with user/one-time-password name and certificate based authentic.

  The main challenge is to put in place its own structure of profile cards, connection profiles, group policies and dynamic access policies.

  Feel free to ask questions...

  Stephan

• NAT and vpn acl

  Hello

  I have asa 5512-x

  ASA 9.1 version 2

  ASDM version 7.2 (1)

  I'm not really good with a syntax of cisco, so I use asdm

  I created a split tunnel remote ipsec vpn with cisco vpn client

  the purpose is to allow vpn for LAN traffic

  and to allow the vpn to a public Web site traffic

  so I set the two objects and added to the exemption of split tunnel (the names of the objects: 'LAN', 'Rackspace')

  access to the local network is ok, access to a Web site does not work

  I guess I have some missing nat/ACL,

  can someone explain to me please in the most simple way to do this?

  Thank you very much

  Hello

  What is subnet

  network of the NETWORK_OBJ_172.18.0.0_26 object
  255.255.255.192 subnet 172.18.0.0

  This 'nat' configuration seems strange

  NAT (LAN, WAN1) source static Tunnel VPN VPN Tunnel static destination NETWORK_OBJ_172.18.0.0_26 NETWORK_OBJ_172.18.0.0_26 non-proxy-arp-search to itinerary

  When you see that the source for the "nat" interface is 'LAN' and source networks are those configured under "Tunnel VPN" it seems to suggest that this NAT configuration transmits traffic destined to 'LAN' and 'rackspace' to the 'LAN' interface. It is naturally very good for the subnet configured under 'LAN' , but the 'rackspace' to my knowledge is located behind an external interface of the ASA correct? But I guess I really need to know this as the subnet that I mentioned at the beginning of the post (which is used in this configuration NAT too)

  What is the interface to which the VPN users connect to? WAN1 or DSL? Although the following list what the map interface Crypto is attached

  See the crypto run map

  You can also list the output of the following command

  See the establishment of performance ip local pool

  -Jouni

• Simple router to VPN support - client connection to the database server

  How can I set up a simple VPN using the WAG325N? Is there a step by step guide that doesn't require me to read a book on the VPN to understand each setting? My needs are quite simple: I need to connect a client computer in Windows Server 2003 running Team Foundaion Server - just like allowing a client to connect to SQL Server running in Visual Studio 2008.

  Otherwise, I could buy a new router. However, I have to have the same feature set as my WAG325N and hopefully allow me to back up the existing configuration + restore on the new router. What router you would recommend?

  In reality, the solution has already been provided by Linksys:

  Instructions to set up the VPN between two routers

  It works very well. Problem solved!

• Unable to connect to the ASA vpn Android client

  secHello, I have problem with android client. So I've solved many problems and finally could get the PHASE 1 and PHASE 1 COMPLETED messages in newspapers :). In any case, I have a problem different, even if the client of the phase 1 and 2 completed failed to connect again. Here are the logs:

  | 21456 | *** | 500 | Built of UDP connection entrants for outdoor 600577524: * / 21456 (* / 21456) identity: * / 500 (* / 500)
  | 27262 | *** | 4500 | Built of UDP connection entrants for outdoor 600577567: * / 27262 (* / 27262) identity: * / 4500 (* / 4500)
  Group = ANDROID_PROF, IP = *, automatic NAT detection status: remote endpoint IS behind a NAT device this end is behind a NAT device
  Group = ANDROID_PROF, IP = *, floating NAT - T of * port 21456 to * port 27262
  Group = ANDROID_PROF, IP = *, PHASE 1 COMPLETED
  Group = ANDROID_PROF, IP = *, IPSec initiator of the substitution of regeneration of the key time of 0 to 4608000 Kbs
  IPSEC: Remote access out HIS (SPI = 0x0429CEA7) between * and * (user = ANDROID_PROF) was created.
  Group = ANDROID_PROF, IP = *, the security negotiation is complete for user (Responder), Inbound SPI = 0xc95803fc outbound SPI = 0x0429cea7
  IPSEC: Incoming remote access between HIS (SPI = 0xC95803FC) * and * (user = ANDROID_PROF) was created.
  Group = ANDROID_PROF, IP = *, PHASE 2 COMPLETED (msgid = 9aab13ed)
  | 27262 | *** | 1701 | Built of UDP connection entrants for outdoor 600577657: * / 27262 (* / 27262) identity: * / 1701 (* / 1701)
  L2TP tunnel created, tunnel_id 24, remote_peer_ip is *, 1/ppp_virtual_interface_id, client_dynamic_ip is 0.0.0.0, user name is *.
  Tunnel L2TP deleted, tunnel_id = 24, remote_peer_ip = *.
  IPSEC: Remote access out HIS (SPI = 0x0429CEA7) between * and * (user = ANDROID_PROF) has been removed.
  IPSEC: Incoming remote access between HIS (SPI = 0xC95803FC) * and * (user = ANDROID_PROF) has been removed.
  Group = ANDROID_PROF, IP = *, Session is to be demolished. Reason: The user has requested
  Group = ANDROID_PROF, user name =, IP = *, disconnected Session. Session type: IPsecOverNatT, duration: 0 h: 00 m: 07 s, xmt bytes: 1021, RRs bytes: 955, reason: the user has requested

  As you can see session was demolished immediately, said Android failure. The Android settings:
  Name: ANDROID_PROF

  Type: L2TP/IPsec Psk

  The IPsec identifier: ANDROID_PROF

  Pre-shared key IPsec: cisco

  The ASA config:

  attributes global-tunnel-group ANDROID_PROF
  address IPSEC_RA_POOL pool
  Group-LDAP LOCAL authentication server
  LDAP authorization-server-group
  NOACCESS by default-group-policy
  IPSec-attributes tunnel-group ANDROID_PROF
  IKEv1 pre-shared-key *.
  tunnel-group ANDROID_PROF ppp-attributes
  CHAP Authentication
  ms-chap-v2 authentication

  ANDROID_PROF_GP group policy attributes
  value of DNS server *.
  VPN - 4 concurrent connections
  Protocol-tunnel-VPN l2tp ipsec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list ANDROID_PROF_USERS
  Cisco.local value by default-field
  the address value IPSEC_RA_POOL pools

  Hello

  Your problem is with Android L2TP/IPsec client that connects to the AAS has been caused by: CSCug60492 (Android phone disconnected from l2tpoveripsec and reconnect asa hung)

  It is Android actually issue, not a bug of the SAA. This resolution is based on Android.

  I hope this helps.

  Thank you

  Vishnu

• SSL VPN without client customization

  Hi all

  I'm learning to clientless SSL on ASA 5520 VPN customization, but I can't seem to add a few.

  y at - it a command or a sine qua non before customization? It could be question of java or asdm?

  ciscoasa # sh ve

  Cisco Adaptive Security Appliance Software Version 8.4 (2)

  Device Version 7.0 Manager (1)

  

  "AnyConnect Premium peers: 2 perpetual" is the key bit there. Those are the two included AnyConnect Premium counterparts with the ASAs.

  The VPN peers 'Other' and 'Total' to take into account the fact that you have also up to 10 IPsec VPN (remote access) or site to site over the two remote access client VPN active one any time.

  In general a remote VPN access can be:

  a. clientless SSL (only a browser required by the counterpart, but requires confusedly, AnyConnect Premium license on the SAA),.

  b. full-tunnel SSL (launch browser or directly from the Anyconnect client, requires either AnyConnect Premium or Essentials on the SAA), or

  c. based on IPsec (using the Cisco's IPsec client inherited with IKEv1 (no AnyConnect license required) or 3.0 AnyConnect client or later (with Essentials or Premium license on the SAA) with IKEv2).

  And there will be a test on this.

• VPN ACL & super networks

  This should be a pretty simple question. With a tunnel can VPN you specify a wider range of IP addresses in the list to access such as 10.1.0.0/8 which accepts traffic from smaller subnets in this range like 10.1.3.0/24?

  I don't know if the ACL check just the IP address, or if the subnet mask must be the same one.

  For vpn traffic great nets will be read and processed, in other words if you set an address for correspondence as:

  IP 10.0.0 allow 0.255.255.255 172.16.0.0 0.0.255.255

  This will include the whole 8 subnets of 10 and 16 all of the subnets of the 172 to send on this tunnel.

  Be careful when you use this part of the traffic you want to can be on this game.

• double authentication with Cisco's VPN IPSEC client

  Cisco VPN client (the legacy IPSEC client) does support dual authentication with RSA token AND ActiveDirectory credentials?

  I know that AnyConnect supports it and the commandsecondary- authentication -Server- group' is only for ssl connections, but must be confirmed.

  Kind regards

  Mohammad

  Hi Mohammad,.

  What is double authentication support for Cisco VPN Client?

  A. No. Double authentication only is not supported on the Cisco VPN Client.

  You can find more information on the customer Cisco VPN here.

  As you said the only client that supports dual authentication is the Cisco AnyConnect secure mobility Client.

  Please note and mark it as correct this Post!

  Let me know if there are still questions about it!

  David Castro,

• VPN routing clients

  I have an ASA 5510 with IPSec VPN installation. VPN clients receive 172.17.0.0 addresses and access to the 172.16.0.0 network (inside the interface the SAA is 172.16.1.1). I need these customers to achieve 172.20.0.0 via an internal router (172.16.3.7).

  How do I configure this? Currently the traffic sends just the 172.20.0.0 customer on its internet connection as split tunneling is enabled. I tried to use a static route on the client which did not work.

  Any ideas would be greatly appreciated.

  Rick

  you have a road to each 172.20.0.0 of the asa network via 172.16.3.7 bridge?

  I would check that.

  1 - asa, a route to reach net 172.20.0.0.

  2-If asa has a route, does 172.16.3.7 router knows how to get to your VPN to the pool?

  3-access list asa to allow/permit pool to the 172.20.0.0 network vpn network.

• ASA 5510 - SSL VPN without CLIENT - remote desktop

  Is it possible to make a desktop connection remote clientless SSL VPN with a browser? I know that I can do with client anyconnect SSL but I can do without a customer?

  Yes it is possible, you must first make sure that you have transferred to the ASA RDP plugin. When you are editing you bookmarks, you will see an option for RDP.

• Adding networks to the tunnel VPN ACL

  Hello. On a remote location, I have to add additional networks access to our networks to the central location and I was wondering is it as simple as the addition of these networks to ACL on both sides of the tunnel to allow access or is there something more to do? I just want to be sure because it is so simple.

  VPN is the site to site.

  Thanks in advance for any help.

  Add traffic to your acl crypto of interesting traffic and your nat exemption acl.

• PIX - PIX VPN and Client VPN - cannot access core network

  I hub and spoke PIX and a VPN Client that connects to speak it PIX, much the same as the example configuration here: -.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00800948b8.shtml

  This example shows the client VPN access to the network behind PIX RADIUS. I want the client to also be able to access the central network, i.e. the client connects to the pix speaks via vpn, and traffic is routed through the vpn to PIX - PIX to the central site.

  How this would change the configuration contained in the example?

  See you soon,.

  Jon

  You can not do this, the PIX cannot route a package back on the same interface, it is entered in the. The only way to do that is to have the client connect to the hub PIX, but then they would not be able to get to the network behind PIX distance either.

  Or that the customer would connect on a different interface in the PIX of distance, but this would mean another connection ISP on this PIX. Example of config is here: http://www.cisco.com/warp/public/110/client-pixhub.html

• VPN without client, RDP Audio

  Hello.

  I use the VPN client without client to connect to our ASA5510 to 8.3. I use remote desktop to connect to an internal machine. It works very well with the ActiveX and Java.

  One thing I want, is to leave the room audio to the remote computer.

  Is there a command line for this switch? As "geometry", "console" and so on.

  Peter

  Hi Peter,.

  RDP Audio redirection exists but only for the ActiveX version of the plugin, not the Java one.
  
  Here is how you should define your bookmark if you want to use this feature:
  
  

  rdp:///?audio=X

  
  
  Where X can be:
  
  

  0: Redirect remote sounds to the client computer.

  1: Play sounds at the remote computer.

  2: Disable sound redirection; do not play sounds at the remote server.

  Kind regards

  Nicolas

• ASA 5510 worm. 8.2 (5) access through VPN without client management?

  Hi all

  I am completely new to networking Cisco and virtual private networks, I'm working on to the ASA 5510 8.2 (5) 46.  Currently, the unit is set up very very little.  Access to the administration are accessible from my home network to 192.168.2.1.  I'm trying to enable management access remotely by VPN.  I created a clientless SSL VPN, which, during the wizard process, access to the specified administration was the/admin adding to the VPN https url.  Add the/admin in the url for VPN is not me the VPN connection, and by using the/admin url from the portal returns a message "not available".  Also, from the portal I can't access the ASDM using inside IP network management, it also returns the message as "unavailable".  Again, I'm new to this, any help would be greatly appreciated.  Here is my config.  and thank you!

  : Saved : ASA Version 8.2(5)46 ! hostname ALP5510 enable password 8Ry2YjIyt7RRXU24 encrypted passwd 2KFQnbNIdI.2KYOU encrypted names ! interface Ethernet0/0 nameif outside security-level 0 ip address 99.66.203.148 255.255.255.248 ! interface Ethernet0/1 shutdown no nameif no security-level no ip address ! interface Ethernet0/2 shutdown no nameif no security-level no ip address ! interface Ethernet0/3 nameif inside security-level 100 ip address 192.168.2.1 255.255.255.0 ! interface Management0/0 nameif management security-level 100 ip address 192.168.1.1 255.255.255.0 management-only ! boot system disk0:/asa825-46-k8.bin ftp mode passive dns domain-lookup inside dns server-group DefaultDNS name-server 68.94.156.1 name-server 68.94.157.1 same-security-traffic permit inter-interface pager lines 24 logging asdm informational mtu outside 1500 mtu inside 1500 mtu management 1500 ip local pool vpn 192.168.2.10 no failover icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-714.bin no asdm history enable arp timeout 14400 global (outside) 101 interface nat (inside) 101 0.0.0.0 0.0.0.0 nat (management) 101 0.0.0.0 0.0.0.0 route outside 0.0.0.0 0.0.0.0 99.66.203.150 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy http server enable http server session-timeout 20 http 192.168.1.0 255.255.255.0 management http 192.168.2.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.2.0 255.255.255.0 inside ssh timeout 5 console timeout 0 management-access inside dhcpd address 192.168.2.3-192.168.2.10 inside dhcpd dns 68.94.156.1 68.94.157.1 interface inside dhcpd enable inside ! dhcpd address 192.168.1.3-192.168.1.10 management dhcpd dns 68.94.156.1 68.94.157.1 interface management dhcpd enable management ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn enable outside enable inside group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn webvpn   svc ask enable group-policy eng internal group-policy eng attributes vpn-tunnel-protocol webvpn webvpn   url-list value EngineerBookmarks username user1 password mbO2jYs13AXlIAGa encrypted privilege 15 username user1 attributes vpn-group-policy eng webvpn   url-list value EngineerBookmarks tunnel-group test type remote-access tunnel-group test general-attributes address-pool vpn tunnel-group Engineering type remote-access tunnel-group Engineering general-attributes default-group-policy eng ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters   message-length maximum client auto   message-length maximum 512 policy-map global_policy class inspection_default   inspect dns preset_dns_map   inspect ftp   inspect h323 h225   inspect h323 ras   inspect rsh   inspect rtsp   inspect esmtp   inspect sqlnet   inspect skinny    inspect sunrpc   inspect xdmcp   inspect sip    inspect netbios   inspect tftp   inspect ip-options   inspect icmp ! service-policy global_policy global prompt hostname context no call-home reporting anonymous Cryptochecksum:05f3afe3383542c8f62b1873421a7484 : end asdm image disk0:/asdm-714.bin asdm location 99.66.203.150 255.255.255.255 inside no asdm history enable 
  
  
  			 
  I'm TAC if you give me a number I can help you, I think we will extend that if we continue on the support forum