Easy VPN - acl

Similar Questions

• Cisco 831 - easy VPN server

  Hello

  I am trying to create an easy VPN server on Cisco 831. When I "test" the easy VPN he said that it tested successfully, but when I try to VPN in the router of the built in Windows XP VPN client, I'm unable to connect.

  Does anyone have recommendations for how to configure easy VPN? I basically just selected all the default options. I was not able to find tutorials in the Cisco online documentation.

  Do I need to have the Cisco VPN client to connect to the Cisco router?

  Other thoughts?

  Your IP address pool you are trying to assign to remote users is part of your local network, which is not the best way to assign the ip address to the VPN Clients, and I've seen a lot of problems in the past were route it not forwards the packets to the client. This allows you to change the POOL of something other than your LAN. E.g. 192.168.1.0/24.

  Also, make sure that you re - configure your 102 ACL accordingly.

  Once you make changes, try to connect again and let me know how it goes.

  Kind regards

  Arul

  * Please note all useful messages *.

• Help with 1921 SRI Easy VPN remote w / Easy VPN Site-to-Site access

  I have two 1921 ISR routers configured with easy site to site VPN.  I configured VPN each ISR ACL so that all networks on each site can communicate with the private networks of the other site.   I have a 1921 SRI also configured as an easy VPN server.

  Problem: when a remote user connects to the easy VPN server, the user can only access private networks on the site of the VPN server.  I added the IP network that is used for remote users (i.e. the Easy VPN Server IP pool) to each VPN ACL 1921, but the remote user still cannot access other sites private network via the VPN site to another and vice versa.

  Problem: I also have a problem with the easy VPN server, do not place a static host route in its routing table when he established a remote connection to the remote user and provides the remote user with an IP address of the VPN server's IP pool.  The VPN server does not perform this task the first time the user connects.  If the user disconnects and reconnects the router VPN Server does not have the static host route in its routing table for the new IP address given on the later connection.

  Any help is appreciated.

  THX,

  Greg

  Hello Greg,.

  The ASAs require the "same-security-traffic intra-interface permits" to allow through traffic but routers allow traversed by default (is there no need for equivalent command).

  Therefore, VPN clients can access A LAN but can't access the Remote LAN B on the Site to Site.

  You have added the pool of the VPN client to the ACL for the interesting site to Site traffic.

  You must also add the Remote LAN B to the ACL of tunneling split for VPN clients (assuming you are using split tunneling).

  In other words, the VPN router configuration has for customers VPN should allow remote control B LAN in the traffic that is allowed for the VPN clients.

  You can check the above and do the following test:

  1. try to connect to the remote VPN the B. LAN client

  2. check the "sh cry ips his" for the connection of the VPN client and check if there is a surveillance society being built between the pool and Remote LAN B.

  Federico.

• How to put all through traffic the easy vpn client VPN server

  Hi people

  I want to ask you, how to put all of the server the easy vpn client VPN traffic through.

  I mean, I have a server vpn at home, and if I connect to the vpn from outside server, to be with an IP address of my home.

  There is the configuration up to now. Where is the problem?

  ROUTER1 #sh running-config

  Building configuration...

  Current configuration: 5744 bytes

  !

  ! Last configuration change at 19:51:18 UTC Wed Sep 4 2013 by cska

  !

  version 15.1

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  no password encryption service

  !

  ROUTER1 hostname

  !

  boot-start-marker

  usbflash0:CVO boot-BOOT Setup. CFG

  boot-end-marker

  !

  !

  !

  AAA new-model

  !

  !

  AAA authentication login ciscocp_vpn_xauth_ml_1 local

  AAA authorization ciscocp_vpn_group_ml_1 LAN

  !

  !

  !

  !

  !

  AAA - the id of the joint session

  !

  Service-module wlan-ap 0 autonomous bootimage

  Crypto pki token removal timeout default 0

  !

  Crypto pki trustpoint TP-self-signed-1604488384

  enrollment selfsigned

  name of the object cn = IOS - Self - signed - certificate - 1604488384

  revocation checking no

  !

  !

  TP-self-signed-1604488384 crypto pki certificate chain

  certificate self-signed 01

  3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 04050030 A0030201

  2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30

  69666963 31363034 34383833 6174652D 3834301E 170 3133 30383239 31313539

  32395A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D

  4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 36303434 65642D

  38383338 3430819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101

  8100CD 57 F1436ED2 8D9E8B99 B6A76D45 FE56716D D99765A9 1722937C F5603F9F

  528E27AF 87A24C3D 276FBA1C A5E7C580 CE99748E 39458C 74 862C 2870 16E29F75

  7A7930E1 15FA5644 D7ECF257 BF46C470 A3A17AEB 7AB56194 68BFB803 144B7B10

  D3722BDD D1FD5E99 8068B77D A1703059 9F0578C7 F7473811 0421490D 627F25C5

  4 HAS 250203 010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355

  551 2304 18301680 141B 1326 C111DF7F 9F4ED888 EFE2999A 4C50CDD8 06 12301

  03551D0E 04160414 1B1326C1 11DF7F9F 4ED888EF E2999A4C 50CDD812 300 D 0609

  2A 864886 04050003 81810096 BD0C2B16 799DB6EE E2C9B7C4 72FEAAAE F70D0101

  FF87465C FB7C5248 CFA08E68 522EA08A 4B18BF15 488D D53D9A43 CB400B54 8006

  CB21BDFB AA27DA9C C79310B6 BC594A7E D6EDF81D 0DB7D2C1 9EF7251B 19A 75403

  211B1E6B 840FE226 48656E9F 67DB4A93 CE75045B A986F0AD 691EE188 7FB86D3F

  E43934FA 3D62EC90 8F37590B 618B0C

  quit smoking

  IP source-route

  !

  !

  !

  !

  CISCO dhcp IP pool

  import all

  network 192.168.1.0 255.255.255.0

  DNS-server 195.34.133.21 212.186.211.21

  default router 192.168.1.1

  !

  !

  IP cef

  No ipv6 cef

  !

  Authenticated MultiLink bundle-name Panel

  license udi pid CISCO892W-AGN-E-K9 sn FCZ1530C209

  !

  !

  username privilege 15 secret 5 cska $1$ $8j6G 2sMHqIxJX8MQU6vpr75gp1

  !

  !

  !

  !

  !

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  !

  Configuration group customer isakmp crypto VPNGR

  vpngroup key

  DNS 212.186.211.21 195.34.133.21

  WINS 8.8.8.8

  domain chello.at

  pool SDM_POOL_1

  ACL 120

  netmask 255.255.255.0

  ISAKMP crypto ciscocp-ike-profile-1 profile

  match of group identity VPNGR

  client authentication list ciscocp_vpn_xauth_ml_1

  ISAKMP authorization list ciscocp_vpn_group_ml_1

  client configuration address respond

  virtual-model 1

  !

  !

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  !

  Profile of crypto ipsec CiscoCP_Profile1

  security association idle time 86400 value

  game of transformation-ESP-3DES-SHA

  set of isakmp - profile ciscocp-ike-profile-1

  !

  !

  Bridge IRB

  !

  !

  !

  !

  interface Loopback0

  192.168.4.1 IP address 255.255.255.0

  IP nat inside

  IP virtual-reassembly in

  !

  interface BRI0

  no ip address

  encapsulation hdlc

  Shutdown

  Multidrop ISDN endpoint

  !

  interface FastEthernet0

  !

  interface FastEthernet1

  !

  interface FastEthernet2

  !

  interface FastEthernet3

  !

  interface FastEthernet4

  !

  interface FastEthernet5

  !

  FastEthernet6 interface

  !

  interface FastEthernet7

  !

  interface FastEthernet8

  no ip address

  Shutdown

  automatic duplex

  automatic speed

  !

  type of interface virtual-Template1 tunnel

  IP unnumbered Loopback0

  ipv4 ipsec tunnel mode

  Tunnel CiscoCP_Profile1 ipsec protection profile

  !

  interface GigabitEthernet0

  Description Internet

  0023.5a03.b6a5 Mac address

  customer_id GigabitEthernet0 dhcp IP address

  NAT outside IP

  IP virtual-reassembly in

  automatic duplex

  automatic speed

  !

  wlan-ap0 interface

  description of the Service interface module to manage the embedded AP

  192.168.9.2 IP address 255.255.255.0

  ARP timeout 0

  !

  interface GigabitEthernet0 Wlan

  Description interface connecting to the AP the switch embedded internal

  !

  interface Vlan1

  no ip address

  Bridge-Group 1

  Bridge-Group 1 covering-disabled people

  !

  interface BVI1

  IP 192.168.1.1 255.255.255.0

  IP nat inside

  IP virtual-reassembly in

  !

  local IP SDM_POOL_1 192.168.4.3 pool 192.168.4.245

  IP forward-Protocol ND

  !

  !

  IP http server

  local IP http authentication

  IP http secure server

  overload of IP nat inside source list 110 interface GigabitEthernet0

  IP nat inside source static tcp 192.168.1.5 3389 interface GigabitEthernet0 3389

  IP nat inside source static udp 192.168.1.5 3389 interface GigabitEthernet0 3389

  IP nat inside source static tcp 192.168.1.5 21 interface GigabitEthernet0 21

  IP nat inside source static udp 192.168.1.5 21 interface GigabitEthernet0 21

  IP nat inside source static tcp 192.168.1.4 3389 interface GigabitEthernet0 3390

  IP nat inside source static udp 192.168.1.4 3389 interface GigabitEthernet0 3390

  overload of IP nat inside source list 120 interface GigabitEthernet0

  IP route 0.0.0.0 0.0.0.0 dhcp

  !

  exploitation forest esm config

  access list 101 ip allow a whole

  access-list 110 permit ip 192.168.1.0 0.0.0.255 any

  access list 111 permit tcp any any eq 3389

  access-list 120 allow ip 192.168.4.0 0.0.0.255 any

  !

  !

  !

  !

  !

  !

  !

  control plan

  !

  Bridge Protocol ieee 1

  1 channel ip bridge

  !

  Line con 0

  line 2

  no activation-character

  No exec

  preferred no transport

  transport of entry all

  transport output pad rlogin udptn ssh telnet

  line to 0

  line vty 0 4

  privilege level 15

  preferred transport ssh

  entry ssh transport

  transportation out all

  !

  Thanks in advance

  To do this you must make the following changes:

  (1) disable split Tunneling by deleting the ACL of your configuration of the client group.
  (2) enable NAT for VPN traffic by adding 'ip nat inside' to your virtual model of the client network to the ACL that controls your PAT.

  Edit: Theses are the changes to your config (also with a little cleaning):

  Configuration group customer isakmp crypto VPNGR

  No 120 LCD

  !

  type of interface virtual-Template1 tunnel

  IP nat inside

  !

  no nat ip inside the source list 120 interface GigabitEthernet0 overload

  !

  access-list 110 permit ip 192.168.4.0 0.0.0.255 any

  no access-list 120 allow ip 192.168.4.0 0.0.0.255 any

  Sent by Cisco Support technique iPad App

• Cannot connect to the easy VPN server

  Hi *.

  I have a stupid problem with my easy VPN server. I took the following configuration to configure the VPN: click on

  Successfully, I can ping 192.168.99.1 but when I start AnyConnect (enter this IP address as serveraddress) on my IPhone, it first says that the server certificate is not valid (I ignore because it is self-signed..) and when I press continue it says that no link could be established.

  What can be the problem?

  It is very likely that you have a configured PAT-pool and simply use the Word key "overload" when from your external interface. In this command, you reference an ACL (or an ACL in a road map) where we need to ensure that your VPN-pool in included in the traffic using a NAT.

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• Easy VPN not able to access the local network

  Hi guys,.

  little hope can help me, I'll give you a run down on the config.

  I have a border router that is a no. 2851 connected to the No. 2851 is a switch cisco 3750 running Routing inter - vlan with four VLANS.

  I have easy VPN server on the edge router No. 2851 I am able to connect remotely from a client vpn cisco with a problem but I can't access the local network on the server, I tried everything with no luck.

  I have a cisco VPN client installed on a 64-bit windows system 7 and I also tried with windows xp 32-bit system and still no luck.

  Please I need help I need to get this race to end of trading today.

  I will be copying and pasting the edge router config please if someone get review and see if the config is good.

  You need to change your ACL PAT of standard to extend and to deny traffic to be translated to the Pool of VPN:

  access-list 120 deny ip 10.10.10.0 0.0.0.3 10.10.50.0 0.0.0.255

  access-list 120 deny ip 192.168.XX.0 0.0.0.255 10.10.50.0 0.0.0.255

  access-list 120 deny ip 172.16.XX.0 0.0.0.255 10.10.50.0 0.0.0.255

  access-list 120 deny ip 172.1X.20.0 0.0.0.255 10.10.50.0 0.0.0.255

  access-list 120 deny ip 192.168.XX.0 0.0.0.255 10.10.50.0 0.0.0.255

  access-list 120 allow ip 10.10.10.0 0.0.0.3 all

  IP access-list 120 permit 192.168.XX.0 0.0.0.255 any

  IP access-list 120 permit 172.16.XX.0 0.0.0.255 aniy

  IP access-list 120 permit 172.1X.20.0 0.0.0.255 any

  IP access-list 120 permit 192.168.XX.0 0.0.0.255 any

  overload of IP nat inside source list 120 interface Dialer0

  no nat ip within the source of the list 1 overload interface Dialer0

  clear the ip nat trans *.

  Hope that helps.

• SDM & easy VPN server problem

  I'm having a problem setting up an easy VPN server using Cisco Security

  Device Manager Version 2. 0a on a router in 1711 with IOS 12.3 (7) XR3.

  I have reset the router to the factory defects since the opening screen of SDM.

  Connect to 10.10.10.1

  User: cisco

  Password: Cisco

  Start SDM for the initial router configuration dialog box.

  Don't use CNS

  On basic configuration screen:

  Hostname set to router

  Domain: test.com

  Synchronize time with local PC

  Change the user name

  New user name: root

  password: xyzzy123

  password: xyzzy1234

  The LAN Interface Setup screen

  IP address set to 10.1.1.1

  Subnet: 255.255.255.0

  Active DHCP server

  Start IP: 10.1.1.50

  End IP: 10.1.1.70

  DNS Configuration screen

  Primary: 45.45.45.45

  Secondary: 45.45.45.46

  Use for DHCP Clients

  WAN Configuration screen

  Ethernet selected without Encapsulation PPOE

  No dynamic (DHCP Client) host name

  Advanced options screen

  Selected for VLAN1 port address translation

  After reading the summary, I chose the FINISH. Asked if dialog box I have

  you want to set up a basic firewall, I selected YES. I left all the

  secure by default items selected. I clicked FINISH. SDM detected that the

  DHCP client on the untrusted external interface and asked if I wanted to

  allow DHCP traffic through the firewall. I selected YES. The configuration

  has been delivered.

  Save the running-config startup-config and reloaded the router.

  Released and renewed my ip address and then reconnected in 1711 from new

  user name and password. SDM restarted.

  Has begun the task of configuration and choose to set up an easy VPN server.

  The opening screen had a command prompt to enable AAA. I launched the selected task

  After that the AAA commands have been delivered to the router.

  I chose the interface FastEthernet0 menu drop-down

  IKE proposals - selected default all the

  Transform set - selected default all the

  Group authorization / policy research - Selected Local only

  Add the user name: User1

  Password: local1

  Encrypt with MD5

  Privilege: 2

  Group permission/User Group Policies

  Add political group: tunnel

  Preshared key: sharedkey

  Selected new address Pool: 10.1.1.80 to 10.1.1.90

  Test after you have configured the selected button.

  Exit this screen, there was a warning SDM on the NAT with ACL rules

  have to be converted into NAT rules with course maps. I clicked YES to let

  SDM convert rules.

  Tests successful Easy VPN Server and client screen displays a warning

  on the "crypto ipsec df - bit clear' needing to be defined." He was not a

  way to put it in SDM and the search function had no success.

  I copied the running-config to the startup-config and tested the router from a

  connect remotely using a different ISP.

  The results:

  The SDM monitor shows the client connection, but the client cannot ping

  any host on the LAN of the router. No one on the LAN can easy ping of VPN client

  Assigned IP of VPN, but they can ping the client using the asigned IP ISP

  address.

  It seems that SDM not correctly configures the 1711 to route of the

  VPN interface to the local network.

  I enclose my 1711 Running Configuration generated by SDM.

  Hello

  I think that the reason why the ping is not successful is that your LAN IP address (connected to the VLAN interface) and the pool of IP addresses assigned to the client are in the same network.

  You can try assigning a pool of IP addresses for VPn clients that is in another subnet (say 10.1.2.80 to 10.1.2.90) and then try to ping?

  You can change the pool by means of configure-> additional tasks-> local swimming pools.

  You can then disconnect the client on the Monitoring page and connect again.

  Kind regards

  Ravikumar

• PlayBook & cisco Easy VPN Server 831

  I don't seem to be able to connect to my router 831 cisco easy vpn server is configured by using my Blackberry Playbook.  Looking at the console of the router I can see Debugging but don't know what it means.  I have attached debugging as well as glued my setup, if someone is able to help me at all it would be much appreciated.  Thank you very much.

  Current configuration: 2574 bytes
  !
  version 12.3
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  router host name
  !
  enable secret 5 $1$ FM71$ y4ejS2icnqX79b9gD92E81
  enable password xxxx
  !
  username privilege 15 password 0 $1$ W1fA CRWS_Ritesh $ o1oSEpa163775446
  username privilege 15 secret 5 shamilton wFLF $1$ $ 8eRxnrrgVHMXXC0bXdEGi1
  AAA new-model
  !
  !
  AAA authentication login default local
  AAA authentication login ciscocp_vpn_xauth_ml_1 local
  AAA authorization exec default local
  AAA authorization ciscocp_vpn_group_ml_1 LAN
  AAA - the id of the joint session
  IP subnet zero
  no ip Routing
  !
  !
  audit of IP notify Journal
  Max-events of po verification IP 100
  No ftp server enable write
  !
  !
  !
  !
  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  ISAKMP xauth timeout 15 crypto

  !
  ISAKMP crypto client configuration group ciscogroup
  (deleted) 0 key
  DNS 172.16.60.246 172.16.60.237
  pool SDM_POOL_3
  ACL 100
  Save-password
  include-local-lan
  !
  !
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  !
  crypto dynamic-map SDM_DYNMAP_1 1
  game of transformation-ESP-3DES-SHA
  market arriere-route
  !
  !
  card crypto SDM_CMAP_1 client authentication list ciscocp_vpn_xauth_ml_1
  map SDM_CMAP_1 isakmp authorization list ciscocp_vpn_group_ml_1 crypto
  client configuration address map SDM_CMAP_1 crypto answer
  map SDM_CMAP_1 65535-isakmp dynamic SDM_DYNMAP_1 ipsec crypto
  !
  !
  !
  !
  interface Ethernet0
  IP 172.16.60.241 255.255.255.0
  IP nat inside
  no ip route cache
  !
  interface Ethernet1
  DHCP IP address
  NAT outside IP
  no ip route cache
  automatic duplex
  map SDM_CMAP_1 crypto
  !
  interface FastEthernet1
  no ip address
  Shutdown
  automatic duplex
  automatic speed
  !
  interface FastEthernet2
  no ip address
  Shutdown
  automatic duplex
  automatic speed
  !
  interface FastEthernet3
  no ip address
  Shutdown
  automatic duplex
  automatic speed
  !
  interface FastEthernet4
  no ip address
  automatic duplex
  automatic speed
  !
  local IP SDM_POOL_1 172.16.60.190 pool 172.16.60.199
  pool of local SDM_POOL_2 192.168.1.1 IP 192.168.1.100
  local IP SDM_POOL_3 172.16.61.100 pool 172.16.61.150
  IP nat inside source overload map route SDM_RMAP_1 interface Ethernet1
  IP classless
  !
  IP http server
  no ip http secure server
  !
  Remark SDM_ACL category of access list 1 = 2
  access-list 1 permit 172.16.60.0 0.0.0.255
  Note access-list 100 category CCP_ACL = 4
  access-list 100 permit ip 172.16.60.0 0.0.0.255 any
  public RO SNMP-server community
  Enable SNMP-Server intercepts ATS
  !
  Line con 0
  no activation of the modem
  line to 0
  line vty 0 4
  exec-timeout 120 0
  password xxxxx
  length 0
  !
  max-task-time 5000 Planner
  !
  end

  Stace,

  *Mar  1 06:40:15.258: ISAKMP: transform 1, ESP_AES
  *Mar  1 06:40:15.258: ISAKMP:   attributes in transform:
  *Mar  1 06:40:15.262: ISAKMP:      SA life type in seconds
  *Mar  1 06:40:15.262: ISAKMP:      SA life duration (basic) of 10800
  *Mar  1 06:40:15.262: ISAKMP:      encaps is 61443
  *Mar  1 06:40:15.262: ISAKMP:      key length is 256
  *Mar  1 06:40:15.262: ISAKMP:      authenticator is HMAC-SHA
  *Mar  1 06:40:15.262: ISAKMP (0:14): atts are acceptable.
  *Mar  1 06:40:15.262: ISAKMP (0:14): IPSec policy invalidated proposal
  *Mar  1 06:40:15.262: ISAKMP (0:14): phase 2 SA policy not acceptable! (local 14
  

  The other end offers AES 256 and SHA IPSec transform set.

  While you have configured:

  crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac

  Suggestion:

  Add a new set of transofrm and apply it under crypto map.

  HTH,

  Marcin

• Help with the easy VPN server with LDAP

  Hello

  I used to be able to set up our easy VPN server with local authentication.

  But now, I'm trying to use LDAP authentication to match with our policies.

  Can someone help me please to check the config and tell me what is wrong with him?

  My router is a Cisco1941/K9.

  Thank you in advance.

  Ryan

  Current configuration: 5128 bytes
  !
  ! Last configuration change at 13:25:16 UTC Tuesday, August 28, 2012, by admin
  ! NVRAM config update at 05:03:14 UTC Monday, August 27, 2012, by admin
  ! NVRAM config update at 05:03:14 UTC Monday, August 27, 2012, by admin
  version 15.2
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  router host name
  !
  boot-start-marker
  boot-end-marker
  !
  !
  !
  AAA new-model
  !
  !
  AAA group ASIA-LDAP ldap server
  Server server1.domain.net
  !
  AAA authentication login ciscocp_vpn_xauth_ml_1 local
  AAA authentication login ASIA-LDAP-AUTHENTIC ldap group ASIA-LDAP
  local VPN_Cisco AAA authorization network
  Group ldap AAA authorization network ASIA-LDAP-ASIA-LDAP group authorization
  !
  !
  !
  !
  !
  AAA - the id of the joint session
  !
  !
  No ipv6 cef
  !
  !
  !
  !
  !
  IP domain name domaine.net
  IP cef
  !
  Authenticated MultiLink bundle-name Panel
  !
  Crypto pki token removal timeout default 0
  !
  Crypto pki trustpoint TP-self-signed-765105936
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 765105936
  revocation checking no
  rsakeypair TP-self-signed-765105936
  !
  !
  TP-self-signed-765105936 crypto pki certificate chain
  certificate self-signed 01
  30820229 30820192 A0030201 02020101 300 D 0609 2A 864886 F70D0101 05050030
  2 060355 04031325 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 30312E30
  69666963 37363531 30353933 36301E17 313230 36323630 39323033 0D 6174652D
  355A170D 2E302C06 1325494F 03550403 32303031 30313030 30303030 5A 303031
  532D 5365 6C662D53 69676E65 642D 4365 72746966 69636174 652 3736 35313035
  06092A 86 4886F70D 01010105 39333630 819F300D 00308189 02818100 0003818D
  C1B7E661 4893D83A EFE44B76 92BAA71A 6375 854 C 88 D 4533E51A 49791 551D8EF7
  F82E2432 E65B401D 27FE4896 2105B38A CB1908C1 9AE2FC19 8A9393C3 1 B 618390
  EE6CB1CC 5C8B8811 04FA198E 16F3297B 6B15F974 13EE4897 97270547 31 74270
  4590ACA6 68606596 97C5D4D5 462CACA0 CDDAC35A 17415302 CFD4E329 8E7E542D
  02030100 01A 35330 03551 D 13 51300F06 0101FF04 05300301 01FF301F 0603551D
  23041830 1680142E FF686472 569BCCF1 552B 1200 1 060355 5B660F30 D35060DB
  1D0E0416 04142EFF 9BCCF155 68647256 2B1200D3 5060DB5B 660F300D 06092 HAS 86
  01010505 00038181 00558F64 05207 D 35 AA4BD086 4579ACF6 BCF6A851 4886F70D
  1D0EA15B 75DBFA45 E01FBA5C 6F827C42 1A50DD11 8922F1E5 3384B8D8 8DD6C222
  0187E501 82C1C557 8AD3445C A4450241 75D771CF 3A6428A6 7E1FC7E5 8B418E65
  74D265DD 06251C7D 6EF39CE9 3 D FE03F795 692763 AE865885 CFF660A5 4C1FF603
  3AF09B1E 243EA5ED 7E4C30B9 3A
  quit smoking
  license udi pid CISCO1941/K9 sn xxxxxxxxxxx

  ISM HW-module 0
  !
  !
  !
  secret admin user name of privilege 15 5 $1 rVI4$ WIP5x6at0b1Vot5LbdlGN.
  ryan privilege 0 0 pass1234 password username
  !
  redundancy
  !
  !
  !
  !
  !
  !
  !
  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  !
  Configuration group customer isakmp crypto VPN_Group1
  xxxxxxxxxxxx key
  DNS 10.127.8.20
  pool SDM_POOL_1
  ACL 100
  netmask 255.255.255.0
  ISAKMP crypto ciscocp-ike-profile-1 profile
  match of group identity VPN_Group1
  authentication of LDAP-ASIA-AUTHENTIC customer list
  whitelist ISAKMP ASIA-LDAP-authorization of THE
  client configuration address respond
  virtual-model 1
  !
  !
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  !
  Profile of crypto ipsec CiscoCP_Profile1
  game of transformation-ESP-3DES-SHA
  set of isakmp - profile ciscocp-ike-profile-1
  !
  !
  !
  !
  !
  !
  !
  interface Loopback0
  IP 10.127.15.1 255.255.255.0
  !
  the Embedded-Service-Engine0/0 interface
  no ip address
  Shutdown
  !
  interface GigabitEthernet0/0
  IP xxx.xxx.xxx.xxx 255.255.255.224
  automatic duplex
  automatic speed
  !
  interface GigabitEthernet0/1
  IP 10.127.31.26 255.255.255.252
  automatic duplex
  automatic speed
  !
  type of interface virtual-Template1 tunnel
  IP unnumbered Loopback0
  ipv4 ipsec tunnel mode
  Tunnel CiscoCP_Profile1 ipsec protection profile
  !
  local IP SDM_POOL_1 10.127.20.129 pool 10.127.20.254
  IP forward-Protocol ND
  !
  IP http server
  local IP http authentication
  IP http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  !
  IP route 0.0.0.0 0.0.0.0 GigabitEthernet0/0
  IP route 10.0.0.0 255.0.0.0 10.127.31.25
  IP route 10.127.20.128 255.255.255.128 GigabitEthernet0/0
  !
  Note access-list 100 category CCP_ACL = 4
  access-list 100 permit ip 10.0.0.0 0.255.255.255 everything
  !
  !
  !
  !
  !
  !
  !
  LDAP attribute-map ASIA-username-map
  user name of card type sAMAccountName
  !
  Server1.domain.NET LDAP server
  IPv4 10.127.8.20
  map attribute username-ASIA-map
  bind authenticates root-dn CN = xxx\, S1234567, OU = Service accounts, OR = Admin, OU = Acc
  DC = domain, DC = net password password1
  base-dn DC = domain, DC = net
  bind authentication-first
  !
  !
  control plan
  !
  !
  !
  Line con 0
  line to 0
  line 2
  no activation-character
  No exec
  preferred no transport
  transport of entry all
  output transport lat pad rlogin lapb - your MOP v120 udptn ssh telnet
  StopBits 1
  line 67
  no activation-character
  No exec
  preferred no transport
  transport of entry all
  output transport lat pad rlogin lapb - your MOP v120 udptn ssh telnet
  StopBits 1
  line vty 0 4
  transport telnet entry
  !
  Scheduler allocate 20000 1000
  end

  Router #.

  Ryan,

  It seems that you are facing the question where it is indicated in the section:

  Problems with the help of "authentication bind first" with user-defined attribute maps:

  * Then you are likely to see a failure in your authentication attempt. You will see the error message "Invalid credentials, result code = 49.  The newspapers will look something like the journals below: *.

  Which is the same error you see. Go ahead and replace in your attribute map and test again.

  If you remove the command "bind-first authentication' configuration above, everything will work correctly.

  https://supportforums.Cisco.com/docs/doc-17780

  Tarik Admani
  * Please note the useful messages *.

• CANNOT ACCESS THE LAN WITH THE EASY VPN CONFIGURATION

  Hello

  I configured easy vpn server in cisco 1905 SRI using ccp. The router is already configured with zone based firewall. With the help of vpn client I can reach only up to the internal interface of the router, but cannot access the LAN from my company. I need to change any configuration of ZBF since it is configured as "deny everything" from outside to inside? If so that all protocols should I match?   Also is there any exemption of NAT for VPN clients? Please help me! Thanks in advance.

  Please see my full configuration:

  Router #sh run
  Building configuration...

  Current configuration: 8150 bytes
  !
  ! Last modification of the configuration at 05:40:32 UTC Wednesday, July 4, 2012 by
  ! NVRAM config updated 06:04 UTC Tuesday, July 3, 2012 by
  ! NVRAM config updated 06:04 UTC Tuesday, July 3, 2012 by
  version 15.1
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  router host name
  !
  boot-start-marker
  boot-end-marker
  !
  !
  Passwords security min-length 6
  no set record in buffered memory
  enable secret 5 xxxxxxxxxxx
  !
  AAA new-model
  !
  !
  AAA authentication login default local
  AAA authentication login ciscocp_vpn_xauth_ml_1 local
  AAA authorization exec default local
  AAA authorization ciscocp_vpn_group_ml_1 LAN
  !
  !
  !
  !
  !
  AAA - the id of the joint session
  !
  !
  No ipv6 cef
  IP source-route
  no ip free-arps
  IP cef
  !
  Xxxxxxxxx name server IP
  IP server name yyyyyyyyy
  !
  Authenticated MultiLink bundle-name Panel
  !

  parameter-map local urlfpolicy TSQ-URL-FILTER type
  offshore alert
  block-page message "Blocked according to policy"
  parameter-card type urlf-glob FACEBOOK
  model facebook.com
  model *. Facebook.com

  parameter-card type urlf-glob YOUTUBE
  mires of youtube.com
  model *. YouTube.com

  parameter-card type urlf-glob CRICKET
  model espncricinfo.com
  model *. espncricinfo.com

  parameter-card type urlf-glob CRICKET1
  webcric.com model
  model *. webcric.com

  parameter-card type urlf-glob YAHOO
  model *. Yahoo.com
  model yapo

  parameter-card type urlf-glob PERMITTEDSITES
  model *.

  parameter-card type urlf-glob HOTMAIL
  model hotmail.com
  model *. Hotmail.com

  Crypto pki token removal timeout default 0
  !
  Crypto pki trustpoint TP-self-signed-2049533683
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 2049533683
  revocation checking no
  rsakeypair TP-self-signed-2049533683
  !
  Crypto pki trustpoint tti
  crl revocation checking
  !
  Crypto pki trustpoint test_trustpoint_config_created_for_sdm
  name of the object [email protected] / * /
  crl revocation checking
  !
  !
  TP-self-signed-4966226213 crypto pki certificate chain
  certificate self-signed 01
  3082022B 30820194 02111101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
  2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43647274 31312F30
  69666963 32303439 35323236 6174652D 3833301E 170 3132 30363232 30363332

  quit smoking
  encryption pki certificate chain tti
  for the crypto pki certificate chain test_trustpoint_config_created_for_sdm
  license udi pid CISCO1905/K9 sn xxxxxx
  licence start-up module c1900 technology-package datak9
  username privilege 15 password 0 xxxxx xxxxxxx
  !
  redundancy
  !
  !
  !
  !
  !
  type of class-card inspect entire tsq-inspection-traffic game
  dns protocol game
  ftp protocol game
  https protocol game
  match icmp Protocol
  match the imap Protocol
  pop3 Protocol game
  netshow Protocol game
  Protocol shell game
  match Protocol realmedia
  match rtsp Protocol
  smtp Protocol game
  sql-net Protocol game
  streamworks Protocol game
  tftp Protocol game
  vdolive Protocol game
  tcp protocol match
  udp Protocol game
  match Protocol l2tp
  class-card type match - all BLOCKEDSITES urlfilter
  Server-domain urlf-glob FACEBOOK game
  Server-domain urlf-glob YOUTUBE game
  CRICKET urlf-glob-domain of the server match
  game server-domain urlf-glob CRICKET1
  game server-domain urlf-glob HOTMAIL
  class-map type urlfilter match - all PERMITTEDSITES
  Server-domain urlf-glob PERMITTEDSITES match
  inspect the class-map match tsq-insp-traffic type
  corresponds to the class-map tsq-inspection-traffic
  type of class-card inspect correspondence tsq-http
  http protocol game
  type of class-card inspect all match tsq-icmp
  match icmp Protocol
  tcp protocol match
  udp Protocol game
  type of class-card inspect correspondence tsq-invalid-src
  game group-access 100
  type of class-card inspect correspondence tsq-icmp-access
  corresponds to the class-map tsq-icmp
  !
  !
  type of policy-card inspect urlfilter TSQBLOCKEDSITES
  class type urlfilter BLOCKEDSITES
  Journal
  reset
  class type urlfilter PERMITTEDSITES
  allow
  Journal
  type of policy-card inspect SELF - AUX-OUT-policy
  class type inspect tsq-icmp-access
  inspect
  class class by default
  Pass
  policy-card type check IN and OUT - POLICIES
  class type inspect tsq-invalid-src
  Drop newspaper
  class type inspect tsq-http
  inspect
  service-policy urlfilter TSQBLOCKEDSITES
  class type inspect tsq-insp-traffic
  inspect
  class class by default
  drop
  policy-card type check OUT IN-POLICY
  class class by default
  drop
  !
  area inside security
  security of the OUTSIDE area
  source of security OUT-OF-IN zone-pair outside the destination inside
  type of service-strategy check OUT IN-POLICY
  zone-pair IN-to-OUT DOMESTIC destination outside source security
  type of service-strategy inspect IN and OUT - POLICIES
  security of the FREE-to-OUT source destination free outdoors pair box
  type of service-strategy inspect SELF - AUX-OUT-policy
  !
  Crypto ctcp port 10000
  !
  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 2
  Group 2
  !
  ISAKMP crypto client configuration group vpntunnel
  XXXXXXX key
  pool SDM_POOL_1
  include-local-lan
  10 Max-users
  ISAKMP crypto ciscocp-ike-profile-1 profile
  vpntunnel group identity match
  client authentication list ciscocp_vpn_xauth_ml_1
  ISAKMP authorization list ciscocp_vpn_group_ml_1
  client configuration address respond
  virtual-model 1
  !
  !
  Crypto ipsec transform-set TSQ-TRANSFORMATION des-esp esp-md5-hmac
  !
  Profile of crypto ipsec CiscoCP_Profile1
  game of transformation-TRANSFORMATION TSQ
  set of isakmp - profile ciscocp-ike-profile-1
  !
  !
  !
  !
  !
  !
  the Embedded-Service-Engine0/0 interface
  no ip address
  response to IP mask
  IP directed broadcast to the
  Shutdown
  !
  interface GigabitEthernet0/0
  Description LAN INTERFACE-FW-INSIDE
  IP 172.17.0.71 255.255.0.0
  IP nat inside
  IP virtual-reassembly in
  security of the inside members area
  automatic duplex
  automatic speed
  !
  interface GigabitEthernet0/1
  Description WAN-INTERNET-INTERNET-FW-OUTSIDE
  IP address xxxxxx yyyyyyy
  NAT outside IP
  IP virtual-reassembly in
  security of the OUTSIDE member area
  automatic duplex
  automatic speed
  !
  interface Serial0/0/0
  no ip address
  response to IP mask
  IP directed broadcast to the
  Shutdown
  no fair queue
  2000000 clock frequency
  !
  type of interface virtual-Template1 tunnel
  IP unnumbered GigabitEthernet0/0
  ipv4 ipsec tunnel mode
  Tunnel CiscoCP_Profile1 ipsec protection profile
  !
  local IP SDM_POOL_1 172.17.0.11 pool 172.17.0.20
  IP forward-Protocol ND
  !
  no ip address of the http server
  local IP http authentication
  IP http secure server
  !
  IP nat inside source list 1 interface GigabitEthernet0/1 overload
  IP route 0.0.0.0 0.0.0.0 yyyyyyyyy
  IP route 192.168.1.0 255.255.255.0 172.17.0.6
  IP route 192.168.4.0 255.255.255.0 172.17.0.6
  !
  access-list 1 permit 172.17.0.0 0.0.255.255
  access-list 100 permit ip 255.255.255.255 host everything
  access-list 100 permit ip 127.0.0.0 0.255.255.255 everything
  access-list 100 permit ip yyyyyy yyyyyy everything
  !
  !
  !
  !
  !
  !
  !
  !
  control plan
  !
  !
  !
  Line con 0
  line to 0
  line 2
  no activation-character
  No exec
  preferred no transport
  transport of entry all
  output transport lat pad rlogin lapb - your MOP v120 udptn ssh telnet
  StopBits 1
  line vty 0 4
  transport input ssh rlogin
  !
  Scheduler allocate 20000 1000
  end

  A few things to change:

  (1) pool of IP must be a single subnet, it is not the same subnet as your subnet internal.

  (2) your NAT ACL 1 must be changed to ACL extended for you can configure NAT exemption, so if your pool is reconfigured to be 10.10.10.0/24:

  access-list 120 deny ip 172.17.0.0 0.0.255.255 10.10.10.0 0.0.0.255

  access-list 120 allow ip 172.17.0.0 0.0.255.255 everything

  overload of IP nat inside source list 120 interface GigabitEthernet0/1

  No inside source list 1 interface GigabitEthernet0/1 ip nat overload

  (3) OUT POLICY need to include VPN traffic:

  access-list 121 allow ip 10.10.10.0 0.0.0.255 172.17.0.0 0.0.255.255

  type of class-card inspect correspondence vpn-access

  game group-access 121

  policy-card type check OUT IN-POLICY

  vpn-access class

  inspect

• Easy VPN - excluded network list

  List of excluded network seems not valid for customers of material.

  I have to site vpn to the other side being dynamic ip would be and tunnel of everything, except a single destination. I am not able to find any information on this... I can configure easy vpn and get all tunnel but I need to exclude a certain destination

  In the acl and acl split tunnel No. - nat, you can add to the very first lines to deny the excluded subnets or ip hosts that you do not want to go through the tunnel and allow all ip ranges 10.0.0.0/8, 172.16.0.0/12, 192.168.0.0/16.

  Have you tried this method?

  Thank you

  Rizwan James

• Cisco easy VPN + loopback interface. static ip address for the client

  Good day people.

  I have a couple a question and answer on which I can't google for a period. BTW I maybe simly use bad aproach to choose keywords.

  Thus,.

  (1) is it possible to assign the same IP to the same customer every time that it authenticated, preferably without using DHCP? Definely im sure it is possible, but can't find match configuration examples (my camera's 1921 Cisco IOS 15.0.1).

  (2) is it possible to assign the dynamic crypto map to the loopback interface (to make EASY VPN Server accessible through two interfaces - maybe you recommend another approach instead?) - that I move the map workingcrypto of int phy loopback - I can not connect with reason "SA Phace1 policy proposal" not accepted

  Hello

  (1) you can attach to the same IP to the same username using RADIUS

  (2) If you have 2 outside interfaces

  Then, you would use

  mymap-address loop0 crypto card

  int gig0/0

  crypto mymap map

  int g0/1

  cryptp map mymap

  By doing so, the local address would actually be the loop0 but Cryptography card HAS to be applied on physical output interfaces

  See you soon

  OLivier

• Easy vpn remote

  I have a router 2611 with ios:c2600 - I - mz.120 - 10, DRAM/FLASH is 26624 K / 6144 K

  and the compact flash is 4966520.

  It would support the easy vpn remote feature? If this isn't the case, what IOS/DRAM/FLASH might be appropriate?

  Hello

  Use feature Navigator find IOS appropriate for different platforms:

  http://Tools.Cisco.com/ITDIT/CFN/JSP/index.jsp

  HTH

  Sangaré

• Cannot access the internal network with Cisco easy vpn client RV320

  I have a cisco RV320 (firmware v1.1.1.06) and created a tunnel easy vpn (= split tunnel tunnel mode), then I installed the cisco client vpn v5.0.07.0290 in Windows 7 64 bit, I can connect to the vpn, but I do not see the other pc ping nor them, no idea?

  Thank you

  Hello

  1. is the firewall on the active Windows 7 computer? If so, please disable it

  2. can you check that you get a correct IP address in the range of the POOL of IP configured?

  3. When you perform the tracert command to access an internal server, it crosses the VPN¨?

  4. is the tunnel of split giving you access to internal IP subnets defined?

  5. on the RV320 you see the user connected and sending and receiving bytes?

  Don t forget to rate and score as correct the helpful post!

  David Castro,

  Kind regards

• With an interface easy VPN client only

  Hi guys,.

  I have an ASA 5505 configuration as simple Client VPN. Current configuration uses two interfaces: inside and outside. I tested the connection to the server and works very well.

  For reasons of site specific I'm limited to a single interface, you can call it inside, lan, whatever. So I need to connect clients to the remote site behind this interface and also use it to reach the easy VPN server. Is it possible in the first place?

  Of course, I will put the default route through the Interior of interface and another router will provide the Internet connection.

  It's so hard to make it work you should consider the answer is no.

  Specifically, you need to have one inside and outside interface or EasyVPN will not come to the top.