32 Vista BSOD problem getting the error '1000008e.

Similar Questions

• A security update for windows vista (KB2665364) cumulative hotfix for Kiibits (KB2647518) Activex and update Windows vista ((KB2679255) I get the error codes 800736B 3 and B 8007371)

  A security update for windows vista (KB2665364) cumulative hotfix for Kiibits (KB2647518) Activex and update Windows vista ((KB2679255) I get the error codes 800736B 3 and B 8007371)  I can't find answers and I'm not tech saavy.  Every day for a month updates failed to install

  Hello

  I would suggest trying the following methods and check if it helps.

  Method 1:

  In the following article from Microsoft Fixit to reset Windows Update components and check if the problem persists, run the fixit.

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

  Warning: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://windows.microsoft.com/en-US/windows-vista/Back-up-the-registry

  Method 2:

  Put the computer in a clean boot state, and then try to install the updates and check if it works.

  How to troubleshoot a problem by performing a boot in Windows Vista or Windows 7:

  http://support.Microsoft.com/kb/929135

  Note: once you have completed troubleshooting, try the procedure described in step 7 to reset the computer to start as usual.

  Method 3:

  Try to download updates from the Microsoft Downloads Web site and check.

  http://www.Microsoft.com/download/en/default.aspx

  Hope the information is useful.

• I just bought Windows 7 upgrade Windows Vista. I get the error message: operation is not supported on this platform. What should I do to get this latest version in my computer?

  The upgrade from Vista to Windows 7

  I just bought Windows 7 upgrade Windows Vista. I get the error message: operation is not supported on this platform. What should I do to get this latest version in my computer?

  Have you tried to do an upgrade installation or a custom installation?  A custom installation requires you to back up your files and settings with Windows Easy Transfer and then reinstall everything after installing the new.  If an update install does not install work, you need to do a custom.

  In addition, a Windows 7 Anytime Upgrade will not work and you get a message from a platform if you have bought a UA and tried to use it with Vista.  Vista upgrade requires a detail, a copy in the Windows 7 box.

• Microsoft Office 2010 on Vista program and get the error message 1406

  I am trying to download Microsoft Office 2010 on Vista program and get the 1406 - Setup cannot write the value to the registry key. 13DE4A42 etc. I get the message on 1406 error and it say the usere has no full control access.  I have change the access if the user has an option of full control. But the error message 1406 always happens.  What can I do else?

  What do you mean 'upload '?

• I can't download the updates on my VISTA computer, I get the error 80246008 No. I tried everything, but it does not help. HELP Please

  I went to the services but I have no shoes click on I tried what was in the help section, but it did not help I am new to the computer and was completely lost what to do you if someone can help please help system is Vista, I get the answer as I am not short , but I'm on the internet. Thank you

  Hello

  Thank you to contact the community Microsoft and we will be happy to help you with your concern.

  According to the description, it looks that you are facing a problem during the installation of Windows update.

  This problem may occur if some of the windows update components are corrupt, so we will try to reset the windows update components and find the number.

  It would be great if you could answer these questions.

  1. have you made changes on the computer before this problem?

  2. What are the troubleshooting steps you have tried?

  I would suggest trying the following methods and check if it helps.

  Method 1:

  I suggest you perform a SFC Scan and check if it helps.

  The tool (SFC.exe) System File Checker scans missing or system corrupted files and repairs them.

  How to use the System File Checker tool to troubleshoot missing or corrupted system files on Windows 7: http://support.microsoft.com/kb/929833

  Method 2:

  Open the Windows Update troubleshooting tool: http://windows.microsoft.com/en-US/windows7/Open-the-Windows-Update-troubleshooter

  Method 3:

  Reset Windows update components, and then check if it helps.

  How to reset the Windows Update components? http://support.Microsoft.com/kb/971058

  Note: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://windows.microsoft.com/en-US/windows7/Back-up-the-registry

  Method 4:

  If you are still having the problem then I suggest you run the system update tool and check if it helps.

  Description of the system update tool for Windows Vista, Windows Server 2008 for Windows 7 and Windows Server 2008 R2: http://support.microsoft.com/kb/947821

  We would be more than happy to help you if the steps above did not solve the problem.

• While trying to install the Kodak printer all-in-one on my Vista computer, I get the error "2147287035" system

  Original title: 2147287035 system error

  Hello

  Tried to install Kodak all in the printer software, then I got the error database error 2203 2147287035 tracking system - windows/installer\a720de.msi.

  Can you please help

  Thank you

  Hello

  If I understand correctly you have a problem with installing the Kodak all in a printer on your Windows Vista computer drivers. I would like to know more information on the issue, so that we can help you better.

  1. What is the error message or an exact error code?

  2. What is the Kodak printer model number?

  Let us try the following methods and check if it works for you.

  Method 1:

  Try installing the driver in a clean boot state. Place the computer in a clean boot state will help you to install programs without any interference from third-party program/application.

  Step 1: How to troubleshoot a problem by performing a boot in Windows Vista or Windows 7:

  http://support.Microsoft.com/kb/929135

  Note: once you have completed troubleshooting, try the procedure described in step 3 to reset the computer to start as usual.

  Step 2: Find and install printer drivers:

  http://Windows.Microsoft.com/en-us/Windows-Vista/find-and-install-printer-drivers

  Method 2:

  Try to install the printer driver in the Compatibility Center.

  Make older programs run in this version of Windows:

  http://Windows.Microsoft.com/en-us/Windows-Vista/make-older-programs-run-in-this-version-of-Windows

  Please respond with the State of the question, so that we could help you better.

• When i proform windows update on the "update for Windows Vista (KB972145)' I get the error code: 80070020 __what I can do to fix this? ____

  I did everything here
  http://social.answers.Microsoft.com/forums/en-us/vistawu/thread/407b76bc-2BBA-42d4-9e9d-34dab373979c

  Error 0 x 80070020 when you use the Windows Update Web site or the Microsoft Update Web site to install updates:
  http://support.Microsoft.com/kb/883825

  Quote your full version of Windows (for example, Vista SP1;) Vista 64 - bit SP2) when you post in a forum or a newsgroup. Please do it in your next reply.

  What application or antivirus security suite is installed and your current subscription?  What anti-spyware (other than Defender) applications?  What third-party firewall (if applicable)?

  A (another) Norton or McAfee application has already been installed on the computer (for example, a free trial version which is preinstalled when you bought it)?

  Have you met either of the two scenarios described in the Symptoms section of http://support.microsoft.com/kb/972145?

  Have you tried to install the update manually by using the link in KB972145 to download the installation program?

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Cannot log on to vista Home premium, get the error "the Group Policy client service has no journal, access is denied."

  Unable to connect, password ok, children with message "the Group Policy client service has no journal, access denied" completely locked, they had tried to access and configure windows media center via the xbox 360 but had problems too. any advice appreciated

  Hello

  
  1. how many user accounts have been created on the computer?
  
  2 how many computers are connected to your network home?
  
  Please follow the links below to solve the problem.
  
  Method 1
  
  If you have a hand (main) user account then log on to the main user account and solve the problem by following the link below.
  
  Step 1
  
  Difficulty of a corrupted user profile
  
  http://Windows.Microsoft.com/en-AU/Windows-Vista/fix-a-corrupted-user-profile
  
  If the previous step fails, then the same try starting in safe mode.
  
  Step 2
  
  Start your computer in safe mode
  
  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode
  
  You can also try to change the standard administrator and restart corrupted account Type and check.
  
  http://Windows.Microsoft.com/en-us/Windows-Vista/change-a-users-account-type
  
  Method 2
  
  Follow the suggestions posted by the user in the community
  " . m - shaggy " to help solve the problem.
  
  http://social.technet.Microsoft.com/forums/en-us/itprovistaapps/thread/c88515b4-4be7-4f6f-9988-80f8a5683b41
  I hope this helps.

• Try to do the Vista system restore, get the error saying the disabled protection system.

  According to the instructions on how to turn it on, it is already stated as on.  Also noticed last restore point listed as on 30/03/2011, even if I run windows update automatically and should have several retores points since then.  How can I fix it?

  Hello

  I suggest you to follow these steps and check if that helps:

  Method 1:
  If you have installed a security software on the computer, then I suggest you try to disable temporary and check to see if the same problem happens. Make sure that you enable security software back once the diagnosis is made to prevent the computer from virus attacks.

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Method 2:
  I suggest you try to run the System File Checker. System File Checker tool will solve the problems of missing or corrupted system files on Windows. It determines which file is causing the problem, then replace the file.
  http://support.Microsoft.com/kb/929833

  It will be useful.

• Starting problems, get the error "there is no disk in the drive. Please insert a disk into drive \Device\Harddisk1\DR1.

  1st problem: yesterday I started getting a popp window with the text following formulation - "there is no disk in the drive. Please insert a disk into drive \Device\Harddisk1\DR1' I have no idea what this introduced him or how stop it.  Any suggestions?

  2nd problem: whenever I restart my computer or shut it down and then power up the white bar that moves from left to right only moving to halfway through and then stops. I then have to hold the power button in until the computer turns off again and then rehit the power button. When it starts to power back up the white bar is always in the Middle, but then begins to finally complete the passage to the far right of the box. This problem started when I loaded the software for my printer Canon MX870 new that I bought and installed in October 2010 and has been done since then. I removed and reloaded the software of the printer on three different occasions but the problem persists.

  Hi frankb911,

  Please see the thread with a similar problem and fix possible:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-performance/there-is-no-disk-in-the-drive-please-insert-a-disk/b9a130b2-4261-4385-a51f-28005f209a1d

  I hope this helps!

• My Windows 7 task scheduler has problems getting the error 'Planner services is not available.

  When I opened my task scheduler, it says "selected task (0) no longer exists", said then "Scheduler service is not available" and it can then reconnect, what I'll do. can anyone help. PLEASE, I BEG YOU!

  Hi Abuh_986,

  Because you are always faced with the question, try to perform a repair installation (upgrade on-site) to solve the problem.

  When you perform an upgrade on the spot, it takes the same amount of time to do the upgrade as to reinstall the operating system. In addition, some of your custom Windows settings may be lost through this process.

  Run a repair installation will restore the current installation of Windows to the version of the installation DVD. It also requires the installation of all the updates that are not included on the installation DVD.

  Note: a repair installation will not damage files and applications that are currently installed on your computer. However, you can take a backup of the data.

  You can check the article to perform a repair installation after you close all running applications:

  How to perform an upgrade on the spot on Windows Vista, Windows 7, Windows Server 2008 & Windows Server 2008 R2

• When itunes download get the error, does not have a valid digital signature that verifies the publication server

  I can not download itunes. I have windows vista.  I get the error message: does not have a valid digital signature that verifies the publication server

  Hi klofcc,

  1. are you able to download and install other applications without any problem?

  2. What is the full error message?

  I suggest that you try the steps from the following links to the article and check if it helps:

  Problem installing iTunes or QuickTime for Windows

  I hope this helps.

• I'm having a problem sharing back and forth between xp and vista & get the error that I don't have permission to access files

  original title: sharing of Vista with XP

  I'm having a problem of sharing back and forth between xp and vista.  I've set up the sharing, but I still get the error message that I don't have permission to access files

  Kill / disable the Vista password protection option. If you have installed a separate firewall, configure it.

• Windows Vista crashes, I get the 'Blue screen of Death' and I have to restart. Different errors each time it crashes.

  Windows Vista crashes, I get the 'Blue screen of Death' and I have to restart. Different errors each time it crashes. I tried to reinstall vista without success of the problem being fixed

  Hello

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------
  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
  Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
  codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during "blue screen of death," collisions
  Displays information on all the "crash" of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.

  You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
  system installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
  smile, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Windows Vista Service Pack 2 (KB948465) I get the error code 80092004 and it was not able to load.

  Windows Vista Service Pack 2 (KB948465) I get the error code 80092004 and it was not able to load.

  Free unlimited installation and compatibility support is available for Windows Vista, but only for Service Pack 2 (SP2). This support, initially planned to end on November 26, 2009, has been extended until February 26, 2010. Availability of support chat or messaging differs depending on your location. Some questions may require that more support for which he is advanced a charge.  Go to http://support.microsoft.com/oas/default.aspx?prid=13014&gprid=582034 & select appropriate category (i.e., download problem;) Installation problem; Problems after installing a service pack). ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft