4540 proBook s win8 64-bit driver missing

Similar Questions

• 4540 proBook s: Win8 only DVD - new installation language

  Hello
  
  I'm not sure if I send this message to the right forum, but here goes...
  
  VERY SHORT VERSION
  
  About six weeks ago, I bought a 4540 of HP Probook which seems to be a well designed system and which came with pre-installed Win8. Are there instructions available on how to install a new version of Win8 (including partitioning and Recovery, System EFI Win and MS Reserved partitions, formatting etc.) using the DVD titled:
  
  HP
  The operating system DVD
  Windows 8 unilingual (EM)
  
  I found how to install Win8 you use others install DVD and partitioning tools which I did not. Thank you.
  
  LONG VERSION
  
  After encountering a problem starting HP Support kindly sent me a single language of Win8 installation DVD. (As they would send me a recovery DVDs, but I asked if they could send media that would allow me to choose my own partitioning etc. during installation.) However I can't find all the instructions concerning the use of it & it appears Win8/UEFI systems is very different from earlier versions of Windows/BIOS I have previously installed.
  
  UEFI does not seem to see the DVD of SL Win8 bootable in the following scenarios:
  (a) native UEFI. Start secure; Quick start
  (b) native UEFI; Start secure; Disabled quick start
  
  UEFI does see the DVD bootable under the following scenario:
  (c) native UEFI; Secure boot disabled; Disabled quick start
  
  With each of the above scenarios, if I hit F9 to start then select "Boot from EFI file" there are anything on the hard drive.
  
  After starting as per c & selection language element, OS & license I get a display screen partitions. Drive C was on the 4 UEFI system partition, but by selecting the score (or other) gives me the warning:
  
  -Windows cannot be installed on the partition of drive 0 4.
  -Windows cannot be installed to this disk. Hardware may not support booting to this disk. Ensure that the drive controller is enabled in the computer's BIOS menu.
  
  Maybe this post looks at the UEFI BIOS settings mentioned above (and maybe I chose the wrong settings).
  
  If I go ahead and install it even when the system still will not boot. It is perhaps not surprising because I suspect that the problem is the UEFI boot somewhere - process even if the (in fact all partitions of original 6) EFI system partition always exist and seem to have readable file systems.
  
  I also tried to install Win8 with other UEFI parameters with a lack of similar success. For example. I think that Legacy mode allows to boot from the DVD but does not allow the installation to proceed.
  
  Any help about installing Win8 SL with associated EFI & other partitions would be greatly appreciated. Thank you.

  The solution is to
  http://h30499.www3.HP.com/T5/notebook-HP-ProBook-EliteBook/ProBook-4540s-WIN8-single-language-DVD-fresh-install/m-p/6414166#M178375

• Qosmio G30-177 and Win7 64 bit - driver missing for TV tuner

  Hello

  I had a problem with my TV tuner.
  I didn't find the right driver for my TV tuner.
  I tested the Vista 64 bit drivers but it doesn t work. I had a yellow exclamation mark behind my TV Tuner.

  I want to start TV with windows media Center, but he says that it doesn't work.
  Can someone help me? What can I do?
  What program can I use to watch TV?

  Thanks for sharing this!

• WIN8 64-bit driver Intel Rapid Storage v.11.6.0.1030, A00 XPS 8500 download fails

  Material: XPS 8500, OS: Windows 8, 64 - bit.

  I am trying to download the latest driver Intel rapid storage (v.11.6.0.1030, A00) for 64-bit Windows 8 from the page downloads and drivers, because the version currently installed (11.5.0.1207) has a memory leak in the service of IAStorDataMgrSvc.exe (it is close to 2 GB of memory using at present and continues to increase). Intel forums suggest the update or revert the driver.

  When I try to download driver Intel Rapid Storage v.11.6.0.1030, A00, called RST_Intel_W84_A00_Setup - 5GPDD_ZPE.exe, the option 'Download single file' gives the error message:

  "Sorry, the requested file could not be downloaded.

  An internal error has occurred. Please try again later. »

  
  

  When I try to download with the option "Download Manager", it gives the error message:

  "The file has been corrupted during the download."

  Please can you advise me how to do a download of this driver?

  You can also get this file here: Intel IRST.  Dell sometimes has trouble with his page drivers and downloads.

  EDIT: by the way; someone seems to have noticed the problem as there are has now two links to the file on the page downloads and drivers.  The first link seems to work, while the latter leads to the page you originally found.

• 4540 proBook s: drivers missing

  Hi, I have a few questions.

  I formatted my computer laptop hp ProBook s 4540 with windows 7 64 bit and I noticed that my laptop is no longer permitted to detect all internet. I did some reading on it and looks like missing the following drivers. I've never done this before, and I guess I need a USB driver download and load them up on my laptop?

  The following drivers are missing:

  Base system device

  Base system device

  Ethernet controller

  Network controller

  PCI Simple Communications controller

  Standard VGA Graphics Adapter (Note: there are two of them and one of them says that the driver is missing.)

  I guess as long as I have my ethernet or my controller network still work once I can just "Update" the other riders and they will work?

  Either way, my network controller hardware ID is -.

  PCI\VEN_168C & DEV_0032 & SUBSYS_1785103C & REV_01

  PCI\VEN_168C & DEV_0032 & SUBSYS_1785103C

  PCI\VEN_168C & DEV_0032 & CC_028000

  PCI\VEN_168C & DEV_0032 & CC_0280

  Hope someone can clarify this for me. Thank you.

  Hello:

  Yes, you can put on a USB drivers and allows to run on your 4540 s.

  Here are links to the drivers you need...

  Standard VGA adapters... this driver will install both of them.

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5229457 & swItemId = ob_105419_1 & swEnvOid = 4059

  X 2 base system device:

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5229457 & swItemId = ob_124666_1 & swEnvOid = 4059

  Ethernet controller:

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5229457 & swItemId = ob_123192_1 & swEnvOid = 4059

  Network controller:

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5229457 & swItemId = ob_108191_1 & swEnvOid = 4059

  PCI Simple Communications controller:

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5229457 & swItemId = ob_124514_1 & swEnvOid = 4059

• ProBook 6550 b: driver missing Base system device

  After you have reinstalled Windows 10 on a Probook 6550 b I can't find the correct driver for both devices.

  -Driver missing Base System Device 1:
  Device PCI VEN_1180 & DEV_E852 & SUBSYS_146D103C & REV_01\4 & 1089976f & 0 & 02E2 requires installation.

  -Lack of pilot system of Base 2 device:
  Device PCI VEN_1180 & DEV_E230 & SUBSYS_146D103C & REV_01\4 & 1089976f & 0 & 01E2 requires installation.

  Is it possible to put me in the right direction?
  
  Thank you very much.

  Lennard

  Hello

  Try to install the Windows 7 version of the Ricoh Media Card Reader Driver.

  Kind regards

  DP - K

• 4540 proBook s mdt2012 net driver

  I searched high and low for a solution and tried several different things, all for nothing will do. We have several new portable 4540 probook s and I'm looking to deploy using MDT 2012 windows7x86. I have uploaded the drivers to my host to deploy and rebuilt my images of pe, but winpe does not connect to my deployment share - error - the following pΘriphΘrique ParamΘtrage did not have a driver installed. I have double and triple checked the driver's inf file and it matches the PCI\VEN id on the material in the factory responsible for the OS. DRVLOAD refuses to load this driver when pointed at it. I use sp59118 for the realtek gigabit lan adapt. I tried the driver for our old 4530 s, and even if she is charged, I was still unable to see an inface or connect to the deployment share. Can anyone help with this? Please? My sanity hangs in the balance on this one. Thanks in advance.

  John

  Hello

  I had replied to your post earlier, but apparently it never went through.

  I tried my 4540 s here with my team multidisciplinary-2012 and it works very well. My litetouch.wim mdt is based on windows 4 and I to use the winpe driverpack sp60861 hp.

  Note that there is also a winpe 3.x SP58992 form.

  Could you let me know what version of winpe, comes your litetouch.wim?  WinPE 3or 4 x 86 or x 64

  To try to reproduce your issue tro I tried the following:

  1. Extract p59118
  2. Has taken a fresh winpe 3.1 without any additional driver added
  3. Use dism to mount
  4. Then add the driver c:\swsetup\sp59118\WIN7\NDIS6\32\hp86win7.inf
  5. commit the changes and unmount the image wim

  I then started the 4540 s that wim has successfully loaded the driver for the CARD, and I could connect to my server mdt-2012.

  I also tried to start my 4540 s fees, vanilla, winpoe 3.1 x 86, then use drvload to load the hp86win7.inf driver does load successfully and again once I could connect to the server mdt-2012

  So, I am sure that this driver is OK.

  Could you tell me what version of winpe, you use?  3 or 4 also x 86 or x 64?

  You can check that the correct driver is loaded in your Michael boot.wim file?  Use dism to get a list of driver and check if you see correctly rt86win7.sys

  In addition, when you boot your mdt boot media, press F8 to get a cmd command prompt and do an ipconfig to check whether you are connected or not.

  Also if you want you could send me (I can give you an ftp site) your wim file bootable and I could watch and I hope to resolve this.

  Let me know

• WIN8.1 64-bit driver for my laptop

  Hello

  I want Windows 8.1 Enterprise 64-bit driver for HP Pavilion dv6-6c50se

  please hurry

  Sorry my bad English

  If not replay and give me any driver, I'm not suggestion bar to buy HP...

  This is NOT official HP customer service and I, like most other people on this forum do not work for HP. It is a forum for users of peer-to-peer supported for class for the HP consumer products. HP maintains no official presence on this forum and it is unlikely that HP will respond in an official capacity. Response of an employee of HP represents his own opinion and not that of HP.

  Sorry, but the HP Pavilion dv6-6c50se is a consumer computer that originally shipped with the installation of Windows 7. NO driver Windows 8.1 will be made available by HP for this model.  In addition, you should have bought a HP class computer business if you want support for an operating system of "enterprise".

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• ProBook 6640b: driver missing for 'Base system device' XP Pro on a Probook 6640 b

  Greetings-

  I get two error messages that read "Base system device" driver missing.  The hardware for the first is ID:

  PCI VEN_1180 & DEV_E230 & SUBSYS_1726103C & REV_01

  PCI VEN_1180 & DEV_E230 & SUBSYS_1726103C

  PCI VEN_1180 & DEV_E230 & CC_088000

  PCI VEN_1180 & DEV_E230 & CC_0880

  And the other is:

  PCI VEN_1180 & DEV_E852 & SUBSYS_1726103C & REV_01

  PCI VEN_1180 & DEV_E852 & SUBSYS_1726103C
  PCI VEN_1180 & DEV_E852 & CC_088000
  PCI VEN_1180 & DEV_E852 & CC_0880

  Any guidance would be appreciated!

  Thank you.

  Hello:

  You need this driver that will install two devices...

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=4149986&swItemId=ob_79991_1&swEnvOid=1093

• 4540 proBook s (H6D81ES #ABF): problem of fingerprints

  4540 proBook s (H6D81ES #ABF) 10 64-bit Windows

  Hello, first of all I want to know whether or not that thing in the picture is the fingerprint. If yes why I see something biometric on Device Manager or the BIOS even after I installed the validity sensor driver and chipset one.

  Also I don't have Windows Hello after setting the PIN too.

  

  @Wajdikh

  Wajdikh wrote:
  

  4540 proBook s (H6D81ES #ABF) 10 64-bit Windows

  Hello, first of all I want to know whether or not that thing in the picture is the fingerprint. If yes why I see something biometric on Device Manager or the BIOS even after I installed the validity sensor driver and chipset one.

  Also I don't have Windows Hello after setting the PIN too.

  

  4540 s laptop HP ProBook

  The fingerprint reader is an optional component of your laptop.

  The image you posted shows the Notepad in the image doesn't have a fingerprint reader; small empty coverage shows where the player would be installed.

  Identify components

  Specifications

  How to add a PIN to your account in Windows 10

  Assign a PIN to use with Windows 10 login is no by-itself provide Windows Hello facial or fingerprint login - Windows Hello requires a device to use: 'properly' (high quality) camera, fingerprint reader

  Learn more about Windows Hello and put in place

  What is Windows Hello?

  When you see a post that will help you,

  Who inspires you, gives a cool idea,

  Or you learn something new.

  Click the 'Thumbs Up' on this post.

  Fixed / responded? Click this post accept as Solution to help others find answers.

• Driver missing for windows 7

  I just installed windows 7 on a Hp 6653 CL. The operating system seems to work very well, but there are 2 drivers in the Device Manager screen which I seem not to be able to identify. the hardware for the devices ID are:

  PCI\ ven_1180@dev_0592@subsys_30cc103c@rev_12
  
  PCI\ ven_1180@dev_0843@subsys_30cc103c@rev_12

  I was wondering if any of the residents gurus have an idea what driver is missing.

  Thanks in advance.

  It is the 5 in 1 Ricoh card reader

  PCI VEN_1180 & dev_0592 & subsys_30cc103c

  Vista 64-bit driver (should work on Win 7, if it installs)

  http://h10025.www1.HP.com/ewfrf/wc/softwareList?OS=2100 & LC = on & DLC = in & CC = US & lang = to & Product = 3650971

  Vista 32-bit driver (should work on Win 7, if it installs)

  http://h10025.www1.HP.com/ewfrf/wc/softwareList?OS=2093 & LC = on & DLC = in & CC = US & lang = to & Product = 3650971

• Pavilion 15-n201sk: driver missing

  computer hp laptop pavilion 15-n201sk windows 7 64-bit

  driver missing for:

  1 - Ethernet controller

  2 - Bluetooth controller

  3 Intel (r) 8 series xHCI HC - 9 c 31

  4. PCI device

  5 - video controller

  6 - unknown device

  Hello:

  You should be able to use the W7 x 64 drivers and the software of this model to yours except the BIOS and firmware files.

  http://support.HP.com/us-en/product/HP-Pavilion-15-N100-notebook-PC-series/5436989/model/6422011/drivers

• Satellite L650 - Win8 cannot find driver for ATI mobility Radeon HD5650

  Hi all

  I have Toshiba laptop Satellite L650-1pe psk1je system & I can't find the driver for Windows 8 for my graphics ati mobility radeon hd 5650!

  Help please.

  Thank you

  Hello

  It is not easy to find the drivers but I found one in the U.S. Toshiba download page. This is the model of laptop similar but with the same graphics inside.

  I put t know if this will help but check it out here.

  Choose Win8 (64-bit) and the display driver, so you should find it there.

  Please post comments.

• Basis of HP probook 6460 b system device driver

  I ve hp probook 6460 b. There 'base system device' driver missing. the hardware id of the device is

  PCI\VEN_197B & DEV_2392 & SUBSYS_161C103C & REV_30

  PCI\VEN_197B & DEV_2392 & SUBSYS_161C103C
  PCI\VEN_197B & DEV_2392 & CC_088000
  PCI\VEN_197B & DEV_2392 & CC_0880

  Please give the link where I can find the driver for the device. any other suggestion is highly appreciated.

  Thank you and best regards.

  Hello

  Download and install the card reader driver JMicron from the following link.

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5045594&prodNameId=5045596&swEnvOID=4055&swLang=13&mode=2&taskId=135&swItem=ob-115197-1

  Kind regards

  DP - K

• 4540 proBook s: black screen

  My 4540 probook s graphics has intel and amd card... when installing drivers intel on my 10 windows, screen turns black... I need help

  anyiego

  If your PC is preinstalled with Win10, there is no reason why you would be installing video drivers because the good ones would already be in place.

  If you have improved your PC to Win10 yourself, the problem is that your PC seems to have switchable graphics, and in this case, MS has a history I'm sorry bad video drivers installation.

  You should see if the graphics drivers from the product page HP for your PC, for 64-bit Win10, fix this problem: http://h20564.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=5229456&swLangOid=8&swEnvOid=4192

  Good luck