6 GB/s SAS HBAS do not post on a R720

Similar Questions

• UCS C240 M4 will not start from the HARD local using MegaRAID SAS HBA 12 GB disc

  I have a new server C240 M4 with 12 GB of MegaRAID SAS HBA. I have configured a key virtual bootable (VD0) with 2 SSDS and disks SAS TB in a RAID 5 Virtual Drive (VD1) + global hot spare with 5 1.

  I installed ESXi on VD0 without any problem, but the system doesn't VD0 as bootable.

  I tried adding a local HARD drive in the boot order using the MMIC, but it seems not to be inserted in the selection of boot device.

  Any help would be appreciated.

  The configured boot order corresponds to the real boot order in the MMIC?

  "I tried to add a local HARD disk to the boot order using the MMIC, but it seems not to be inserted in the selection of boot device."

  Ensure that the RAID controller is enabled in the BIOS Boot Options:

  b

  

  Also ensure that the PCIE slots are enabled:

  q

  

  If you still have trouble, let me know.

  -Wes

• RAID works using MD1200 r.620 and 6 GB/s SAS HBA?

  We have a r.620 with Dell SAS HBA already in which is attached to a tape of 124 t library.

  Just got a MD1200 and I plugged in the other port on the SAS HBA.  I can see the drives in Windows Disk Manager.  I can also see Open Manage, but there is no option to use RAID functions or create virtual discs.  Should there be?

  In fact, OpenManage said "Connector 0 (no RAID)" with regard to the SAS 6 GB/s HBA.   I searched online for drivers for this card that allow RAID and can not find.  Am, I watered?   How the RAID to work on the MD1200?

  Hello wardog25,

  For the MD1200 you use a PERC card because it will allow that you create a raid array. The SAS 6hba that is used for your 124 t isn't a raid card, so you will not be able to create a raid on this map. For a MD1200, we recommend that you use a PERC H800. Here is a link to the Guide of interoperability for the MD1200 & if you look at page 2, it lists the supported raid controllers. FTP://FTP.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_powervault/PowerVault-md1200_Reference%20Guide_en-us.PDF

  Here is a link to buy a PERC H800 if you need.

  Please let us know if you have any other questions.

• Reference Dell 6gbps SAS HBA and Powervault TL4000

  Hello.

  We have a server Poweredge R620 with Windows 2008 R2, two Dell 6gbps SAS HBA cards installed and Simpana software backup R2 9.0.

  We also have a TL4000 with two IBM drives, all firmwares are up to date.

  Each SAS HBA card is connected to each drive in the library via a single cable SAS.

  I can see the cards in the Server Device Manager.

  The library works, but when I monitors the status of the disk in the web interface of the ilbrary, the two ports and B seem to 'not ready, not connected. "

  I tried to use Simpana to detect the library. But it cannot detect anything after dozens of tests and scenarios.

  What I am doing wrong? I can provide all of the information you want.

  Thanks in advance.

  Problem has been resolved with the help of Bestami Bayramoglu of Dell Technical Support team.

  I took some pictures of the rear of the server and the library and sent them to Bestami.

  They analyzed and was told that the SAS cards were not inserted and locked properly.

  These cables are equipped with a locking mechanism and they do not work if they are not inserted and locked properly.

  Another question for readers; SAS cards inside my server r.620 part number is j53x3. Crack of metal of this card is not compatible with my server in a rack. The correct we reference number is 3ddjt.

  Bestami told me about this and we will order correct.

  Thank you for your support.

• SAS HBA or Raid for R905 for external storage?

  So I got a R905 used off ebay.  I wanted to use it for a storage server.  Unfortunately, the LSI SAS HBA or the Areca 1883 work in one of the 7 pci-e slots.  The cards are seen and their bios are launched and start automatic and other tests.  Two of them crash during initialization (it is not a matter of waiting a few minutes - in a trial, let him so all day while I was out).  I know that the slots are not dead, like the map 4-port gbe enet provided with it works great, just like a connection-x 2 infiniband card.  I confirmed that the bios and bmc firmware are the latest and best.  It's a kind of dell 'we do support the controllers dell' thing?  If so, I guess I agree with the purchase of a dell SAS HBA connector sff-8088 with random (since that's what jbod I want to connect using...)  Any thoughts appreciated...

  Hello.

  No Dell non-certified controllers are not validated to work properly on Dell servers. But this does not mean that may not work, it's a 50-50 chance. I recommend using certified Dell SAS HBA card such as: manufacturer: 7RJDT | Dell reference: 342-0910. Not so sure on the type of connector

• HP SAS HBAS with IBM Storage and SAS SAN vs iSCSI SAN

  Hello, I am working on a project, and I have to add a SAN solution to my client infaestructure. My client already has a HP Server and we wanted to add another server, but an IBM one. I thought I'd add storage IBM (DS3200) that has two SAS interfaces. The problem is that the Distributor IBM says who does not know if the HP Server will be able to communicate with the SAS IBM storage. So, one possibility was to put on the server HP HP SAS HBA Controller. The second option is to put a SAS HBA Controller IBM. I think that the SAS is a standard, it doesn't matter what brand I use of HBA. Should not it works anyway?

  There is another option which adds instead of SAS one iSCSI storage. The problem is that I do not know the performance than the iSCSI storage. I want to put inside it's VM with Exchange Server (50 mailboxes), an ERP (for 50 users) with it's SQL Server, a computer file virtual, a virtual machine server with Active Directory.

  So, the questions are:

  1 - does anyone have experience with iSCSI storage to see if its performance if goog enough (I intend to use a dedicated to the iSCSI network gigabit switch)?

  2 does anyone know if I use different brands of servers (in this example an IBM and HP) with a SAS storage IBM? Who be it already done? The HP SAS HBA are compatible with the IBM iSCSI storage? IBM SAS HBA are compatible with HP servers?

  3. in the case of being able to do what I say to question 2, that do you suggest? Put a HP SAS HBA within the HP Server or upgrade an IBM SAS HBA inside HP Server?

  Of course the option I want to use is the addition of SAS IBM storage instead of using an iSCSI one, but I'm not sure of their compatibility between HP and IBM storage servers.

  Thanks in advance.

  In this case, the reason why I wouldn't use SAS is that your application requires this level of performance and the cost as not justified. You can configure iSCSI and direct savings in most important features such as snapshot, replication and dedup. If you were available to this solution with the DS3200 spend you 10K and that none of these features. Performance is very good, but you will find that the system is not yet warmed up with this load. The SAS Protocol can support high IO, but is not what provisions IO, is the number of disks and the RAID mode that defines your ability to e/s. I put 40 K terraced small IOPS / s on a single caching of 1 GB iSCSI target, so he can make the e/s. flow is not as high , but do you really need it. In the future you can profitable move to 10Gbe if you find insufficient bandwidth, which would be faster than the SAS 3 GB limit that is uneconomic to upgrade 3 + times.

  Kind regards

  Mike

  http://blog.laspina.ca/

  vExpert 2009

• LSI SAS HBA Boot disabled R720

  How can we disable LSI SAS HBA to start? I JBOD connected to it and do not want to analyze and attempt to start on reboot or start the process

  I believe that you can accomplish this by entering in BIOS and under integrated devices click on the invalidity of the slot. For the specific PCIe slot set the invalidity of the slot to "Boot driver disabled. This will allow the slot be visible to the OS, but it is not available as a boot device.

• Z210 and SAS HBA: those that will work?

  I have an Z210 with the processor E-1240 and 16 GB of RAM, Win7 64-bit.  I have a few hard drives SAS 15 K HP's and I want to install on this machine - but the Z210 has no integrated SAS controller. I discovered that there is an Avid Certified version of this computer, and it uses a controller LSI SAS SAS9200-8F to hang the external storage drives. LSI SAS9200 - 8 used to be available in a version of the internal interface (LSI SAS 9200-8i), but that is only apparently now deployed for IBM and there are no Windows 7 drivers.

  I want to install an INTERNAL SAS HBA. and I noticed that there is an older model, the LSI SAS3041e, which has drivers for Windows7 64-bit available. So, I think that this cheap SAS HBA could be a good candidate for my Z210.

  Has anyone any how SAS HBA in an Z210 properly installed? Specifically the SAS3041e LSA? I think that the issue could boil down to how you install drivers and access the HBA for the boot BIOS...

  DRM for your collective wisdom!

  Well, after much research, I decided that the LSI SAS3041-e (non-RAID) controller was a likely candidate. They are available on eBay for almost nothing.

  I just installed one in my Z210 and it was as easy as possible: Although the technical docs of LSI a several step process to load the drivers Windows 7 Pro 64-bit with Service Pack 1 installed, the drivers are already present in Windows 7 Pro. I plugged the controller, hooked to a pair of HP SAS 15 K disks and booted from the disc of Windows 7 HP system recovery.

  The controller immediately recognized Z210 installed the BIOS and I was off and running. Installation of Win 7 completed smoothly and when the machine finally started in a new Win 7 system, everything was fine and my two new hard drives SAS have been properly formatted and correctly recognized. You should be aware that you will need a pair of "bizarre" SATA cables to use these discs 'battleship-quality '. Cables have a conenctor unified at one end to connect the SAS drives, and the other end is a plain old SATA drive connector and a SATA power plug.

  Even if SAS 15 K drives are slightly slower than a disc of 6 GB/S SATA III, the practical speed difference is trivial, these drives have a superior quality construction regular SATA HD, I think.

• Satellite A300 - towers, but do not post

  Hello

  I hope that someone has had the experience of a similar question to mine, I have a * Toshiba Satellite A300 * which is a couple of years old, but has been problem free until the last two weeks.

  The question:
  -Laptop turn on but does not post, power tubes, display work etc.
  -Let the battery fully discharged and now the power button for 60 seconds will sometimes allow the laptop to work again, but this work around less frequently works all the time.
  -The problem is the same with or without battery
  -Probably adapter works as the laptop occasionally works and works of battery/power LED

  Why the laptop power it will prevent start from time to time?
  Tips or advice would be great, apparently not a major hardware problem and it certainly doesn't seem to justify a replacement yet.

  Thank you
  Chojin81

  Hello

  Hmm... I guess that if only sometimes maybe it's a malfunction of the equipment. If your computer doesn't start it has nothing to do with Windows so it of not a software problem.

  Do you have the hardware upgrades to the last time? Perhaps the new RAM module is not compatible or something else.
  You can see the RAM modules to find errors using Memtest86.

  In the worst cases, the error is related to the motherboard and it is an expensive part of notebook.
  Is your laptop under warranty? Whether an ASP can repair free of charge.

• Z820 with LSI 2308 sas controller will not publish with intel PCIe SSD installed.

  Z820 with LSI 2308 sas controller will not publish with intel PCIe SSD installed. The system works fine with Sata 600 pro SSD for windows and WD 4 TB Black seagate for storage. When the Intell 900 PCIe SSD drive is installed the system hangs at the LSI Mini OROM screen remains white. is there a way to put the LSI controller to jump the PCIe slots for boot devices?

  2 X Xeon 2695, 64 GB Ram, graphics Nvidia Quadro K5000, 2 X Intel 10 GB Ethernet card.

  Thanks for the reply. In fact I've disabled the LSI controller and connected to the integrated SATA controller and the Z820 starts and works perfectly with the PCIe SSD installed.

  Thank you.

• Payment is in AP but not posted in General Ledger

  Helloo everyone,

  I have a problem.

  Some payments were recorded in the AP. However when querying account book in general nothing is found.

  

  As you can see on the statement in detail above was treated and GL date is February 26, 2015, however the same information is not found in the GL.

  Grateful if someone can identify with the scripts or docs oracle for this problem because it has implications for the process of reconciliation.

  This issue should be closed now,

  Please post (or the facility and annex) accounting machine to capture these inputs into account analysis and the Trial Balance reports

  From r12.0, account analysis report replaces Ledger of account by account in r11i

  Account analysis report provides detailed information on the movement on a special account for a period or periods. It includes only the transferred log entries to and posted to the General Ledger. However, this report does not show the posted and unposted items like what was in the report of the 11i version.

  Currently, there is an emergency room for this report: Bug 6450291 : ACCOUNT ANALYSIS REPORT SHOULD HAVE OPTION DISPLAYED, not POSTED AND TRANSACTIONS

  
  

  Thank you
  

• Why can I not post in Adobe Story community

  I can post in other communities are sounds, but when I try to post a question in the history of adobe forum there is not to "Start a Discussion" Option in the action taking place...

  Why can I not post in there?

  Thank you!

  Thank you... Yes-sorted

• SHARED-UNKNOWN-ERROR: 22-What does this mean? can not post the site that this error when I try.

  SHARED-UNKNOWN-ERROR: 22-What does this mean? can not post the site that this error when I try.

  Hello

  Please sign of Muse and identify yourself again and try to publish.

  You have the option of disconnecting help > Sign Out

  In the case that do not fix the issue made me know.

  Concerning

  Vivek

• Storage - SAN iSCSI 1Gbit o 6Gbit SAS HBA

  Ciao,.

  scusate ragazzi, serve my e find the retta via...
  GIA conosco iscsi sas e-tra rant...
  Proposte che mi sono arrivate familières grossomodo configurazioni stessa, con due nodi, my ognuna di interconnettersi allo storage prevedere to was different.
  The SAN PS4100 of mi DELL offers
  The IBM mid DAS (SAN) DS5300 offers.
  Adesso, considerazioni IOPS / s a parte che ho gia fatto e ad incidere vanno solo dei sulla configurazione brain (tipo, e number raid)... I wanted to concentrarmi sulla parte interconnessione.
  Ho come idea percorrendo the DELL mi ritrovi imprigionato strada che... Imprigionato dal fatto di avere una con 2 connessioni sole di rete ridontate entrylevel SAN da 1 Gbit. (4 + 2 management totali)
  Percorrendo strada IBM invece ho impressed di avere a canale nice technologist e veloce. 2 SAS HBA controller per ogni nodo di 6Gbit. (4 SAS HBA + 2 NIC management).
  Non lo so is mi must impressionare questi valori, mi'd leggere it vostro punto di vista.
  IO non riesco a choose.
  THX

  Luca Dell'Oca ha scritto:

  Resterei sul discorso di Francesco did, SAS e molto più easy da configurare, my live attach no you andare oltre 4 Server substitutes i can usually; iSCSI ha invertiti pro e contro.

  Ciao, Luca

  rispondendo All allowed:

  preferirei sentirmi più libero di add server dedicated negoziazioni difficolta di configurazione... che queste TR % in some modo.

  Ben più difficult it could essere superare no problema "fisico.

  Giusto?

  ForSE no, siamo capiti SAS in DA e moooolto più semplice da configurare. In the HBA AI controller nel modo product, ISP he lun masking e hai finito. You can max 4 host collegare.

  Con iSCSI which prevedere 2 eth level di certo UN, configurare correctly switch VLANs, LACP, trunking, jumbo ecc. ECC.

  Potrai collegare tutti I server che nel degli limit you want to switch.

  All'aumentare degli host treatment probabilmente raggiungerai degli index degli storage limits.

  You quanti host ESXi you want to employ? Hai anche altri tipi di collegare host da? Linux o Windows.

  Hai weather di crescita per I 4/5 of next years?

  Ciao

• ESXi 3.5 on Dell Poweredge 2950 and Dell 6 GB/s card SAS HBA?

  Hello.

  I'm under ESXi 3.5 u4 on a Dell poweredge 2950 machine.

  I recently bought a Dell Powervault 124 t. autoloader with a HBA SAS 6 GB/s card.

  I installed the card SAS in the PE 2950, but now I can't seem to see in ESXi.

  Can someone help me with this?

  Thank you very much.

  I'm afraid that the Dell technician is correct.

  Someone at - it a link on ESX support not directly connected devices?

  This isn't the issue. The question is: do you have a link that shows devices supported?

  Reference Dell does support the autoloader Powervault 124 t. on ESXi 3.5?

  Have you checked the VMware HCL already, if the SAS controller is included/supported for ESXi version, you are running?

  There are a few articles which have tape readers running with Adaptec SCSI controllers, I don't see anything for ESXi 3.5 with a SAS controller still...

  Maybe there's a better chance to make this work with ESX 4.x with VMDirectPath

  André