887VA hit in Rommon mode

Similar Questions

• I can't delete files in Access Point 1602 ROMMON mode

  Hello:

  I want to know if it is possible to remove files or directories that are currently allocated in the flash memory. As you can see in the following output, I'm in ROMMON mode and one of the images cannot start propoerly.

  AP: dir flash:
  Directory of flash: /.

  10 drwx 832- ap1g2-k9w8 - mx.153 - 3.JBB
  7 - rwx 230 env_vars
  drwx 5 0 ?
  6 - rwx 1048 private-multiple-fs
  39 384 drwx configs
  8 drwx 64 ap1g2-k9w7 - mx.152 - 4.JB6
  41 drwx 832 ap1g2-k9w7 - mx.153 - 3.JD
  265 - rwx 349557 crashinfo_20160705-223838-UTC

  7404544 bytes available (24531456 bytes used)
  PA:

  Best regards.

  OK, let's do this easily.

  If independent IOS, this is what you want the PA to start with, the more simple (and fast) to get this race is to format the flash of the AP (command: format flash :).)

  When formatting is finished, load the standalone IOS using the method of the Mode button.

• Want to update IOS through the Rommon mode in router Cisco 881

  Hi all

  I'm not able to upgrade IOS via mode Rommon in Cisco 881 router as FE 4 port is in router only L3 and rommon mode it supports of 0 - 3-way only.

  So please confirm for me that is there any other way or Cisco 881 router will not support IOS via Rommon upgradation.

  Kindly help.

  Hi charrier you do not give the ip address of the router interface he gets in rommon so it should not matter what interface, as long as your pc and peripherals, same subnet to push the tftpdnld - see doc

  http://www.Cisco.com/c/en/us/TD/docs/routers/access/800/software/CONFIGU...

  EDIT: See this too good examples even syntax for 800

  https://supportforums.Cisco.com/document/12441/tftpdnld-ROMMON-command-r...

• ROMMON mode

  Today, sometimes early in the morning. Not able to access the router. Since the console port that what he says.

  What should I do?

  ================================================================================

  System Bootstrap, Version 12.3 T9 SOFTWARE (8r), LIBERATION (fc1)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 2004 by cisco Systems, Inc.

  IVC version 0 x 10

  GIO ASIC version 0 x 127

  c1841 processor of 131072 KB of main memory

  Main memory is configured for 64-bit with disabled parity

  ReadOnly initialized ROMMON

  device does not contain a valid FS

  boot: cannot open "flash:

  init: cannot determine the first name of executable file on the device "flash:

  System Bootstrap, Version 12.3 T9 SOFTWARE (8r), LIBERATION (fc1)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 2004 by cisco Systems, Inc.

  IVC version 0 x 10

  GIO ASIC version 0 x 127

  c1841 processor of 131072 KB of main memory

  Main memory is configured for 64-bit with disabled parity

  ReadOnly initialized ROMMON

  ROMMON 1 >

  I think you SEE is defective.

• Airplane mode / phone access

  Hello

  This has been bothering me for some time now and I wanted to post to see if anyone had any ideas on that.

  So now, if your phone is stolen, the person with the phone can put your phone in airplane mode without actually going into the phone, just in gestering upward and hit the airplane mode button.  Once this done, your phone is not visible and cannot be followed by find my phone.

  Is there any fixes for this?  It's something that should only be allowed if your logged in the phone via your code or fingerprint recognition.

  Thank you all.

  To prevent this, go to settings > control center > disable allow access to the lock screen.  -AJ

• Why the pdf links don't work for Muse in preview mode?

  I want to add PDFs on my Muse site, but they are not opening in preview mode. I have the PDF files loaded as files in my property and make them related to the text on the page. But, when I hit the preview mode, the links do not work. Any tips? They were always open when the site is published?

  They will not work if you use the file > Preview in browser or file Page > Site overview in the browser. They do not work for the preview window integrated into the Muse.

• 501 PIX password recovery problems

  Greetings,

  I read the paper on password recovery, unfortunately, the orders contained in the document are not available in the PIX that I use.

  Only commands that I see are:

  Enable

  opening of session

  Logout

  pager

  quit smoking

  I can see as well

  checksum

  curpriv

  history

  pager

  Version

  I can't go to one of the commands to connect to the tftp server as described in the instructions to the:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_password_recovery09186a008009478b.shtml

  I have the .bin file of recovery password that I can't seem to get it on the PIX. Any help is greatly appreciated.

  Thank you

  Hi Brian,.

  The command that you see in the RFSO are in rommon mode, not in the normal PIX config mode, you must reload the PIX, when IP is starting, keeping hitting the ESC key and it will take you to the rommon mode. Then, you can find these commands.

  I hope this helps.

  Thank you

  Varun

  Please evaluate the useful messages.

• Cisco ASA 5510 - IOS upgrade 7.0 failing. Not found Flash BIOS

  Hello everyone

  I have a Cisco ASA 5510 in a lab with none of the configurations environment what so ever.

  Objective: upgrade the IOS current version 7.0 (8) to 7.1.1 (possibly go to 8.2 until memory upgrade on the SAA: 256 MB to 1 GB and then move to the latest version of 8.2 IOS).

  Output to see the attached Version.

  Output Flash attached show.

  asa711 - k8.bin is the file that has been copied from a TFTP server to flash.

  The following commands have been executed in order to update the IOS

  ciscoasa (config) # boot flash system: / asa711 - k8.bin
  INFO: Conversion of flash: / asa711 - k8.bin to disk0: / asa711 - k8.bin
  ciscoasa (config) #.
  ciscoasa (config) # end
  ciscoasa # write memory
  Cryptochecksum: aaaa08ce ccde38f2 19c42e08 dea24cbd
  2713 bytes copied in 1,450 dry (2713 bytes/s)
  [OK]
  ciscoasa # reload
  

  PROBLEM: the device ASA goes in an infinite loop (guard restart). This is the message on the console:

  The system boot, please wait...

  CISCO SYSTEMS
  Embedded BIOS Version 1.0 (11) 15:11:51.82 5 08/28/08
  Memory: 631ko
  Memory: 256 MB
  PCI device table.
  Bus Dev Func VendID DevID class Irq
  00 00 00 8086 2578 host Bridge
  00 01 00 8086 2579 PCI to PCI bridge
  00 03 00 8086 PCI bridge to PCI 257 b
  00 1 00 8086 PCI bridge to PCI 25AE
  1 d 00 00 8086 25A 9 Serial Bus 11
  1 00 01 8086 25AA Bus series 10 d
  1 d 00 04 8086 25AB system
  1 d 00 05 8086 25AC IRQ controller
  1 d 00 07 8086 25AD Bus series 9
  1E 00 00 8086 PCI bridge to 244th PCI
  1F 00 00 8086 25A 1 ISA Bridge
  1F 00 02 8086 25 IDE controller has 3 11
  1F 00 03 8086 25A 4 Bus series 5
  1F 00 05 8086 25A 6 Audio 5
  02 01 00 8086 1075 Ethernet 11
  03 01 00 177 D 0003 encrypt/decrypt 9
  03 02 00 8086 1079 Ethernet 9
  03 02 01 8086 1079 Ethernet 9
  03 03 00 8086 1079 Ethernet 9
  03 03 01 8086 1079 Ethernet 9
  04 02 00 8086 1209 Ethernet 11
  04 03 00 8086 1209 Ethernet 5
  Evaluate the BIOS Options...
  Launch of the BIOS Extension installation ROMMON
  Cisco Systems ROMMON Version (1.0 (11) 5) #0: Thu Aug 28 15:23:50 CDT 2008
  Platform ASA5510
  Use BREAK or ESC to interrupt the boot.
  Use the SPACE to start boot immediately.
  Start the program boot...
  Startup configuration file contains 1 entry.

  Load disk0: / asa711 - k8.bin... The starting...

  256 MB OF RAM
  Total of SSMs found: 0
  Total cards network found: 7
  mcwa i82557 Ethernet to irq 11 MAC: 0024.974a.65af
  mcwa i82557 Ethernet to the irq 5 MAC: 0000.0001.0001
  Not found BIOS flash.
  Reset...

  The only way for me to do things to normal is if I BREAK the sequence starting with ESC and go into ROMMON mode. I then issue a start command for the SAA to start with 7.0 (8) default IOS Image.

  Please can someone explain what is the problem here?

  Apologies if I'm missing something obvious that I'm not an expert of the SAA.

  Looks like that the ASA is hitting a field notice: fn62378. The FN, it's because of the incompatible version of hardware and software. Please upgrade to version 7.1.2 instead of 7.1.1. If you plan to spend in 8.2. So instead of going 7.1.2 you could go to 7.2.5 (recommanded), then 8.2.5

  http://www.Cisco.com/c/en/us/support/docs/field-notices/620/fn62378.html

  It will be useful.

  Kind regards

  Akshay Rouanet

  Remember messages useful rate.

• How can I resolve 'Incompatible IP Settings' NI Max?

  Hi all, I'm using LabVIEW 2012 SP1, my hardware is a NI 3110 industrial controller, which connects to various Beckhoff EtherCAT Terminals.

  I'm having a problem with 'Incompatible IP Settings' NI Max when I try to connect to my goal of RT (NOR-3110 industrial controller). I am able to connect to the target without problem, but be it via DHCP or static IP address, I keep getting 'Inconsistent IP Settings'. I downloaded a few screenshots to imgur album, you can see here. Here is a list of things I've tried (and various combinations):

  1 / flipped "IP Reset" switch on the controller, reset it and put the ip of the PC to a static IP address on the same subnet.

  2 / hit the 'Safe Mode' switch the Safe Mode boot target and connect.

  3 / formatting of the target and reset network through MAX cards.

  4 / DHCP configuration where the target has it of own IP assigned automatically and is visible on my network of the University.

  To be clear, I am * not * having a problem connecting to my target, it is very easy to connect via DHCP and static IP, but I can't seem to get rid of incompatible IP settings.

  I have read many topics Forum and knowledge base articles that suggest that this is usually the result of the IP address of the target and the PC is on a different subnet. However, as far as I can tell this is absolutely * not * the case. The IP address of the target is 10.158.20.8, and the host PC is 10.158.20.x (this varies) and the subnet mask is 255.255.255.0 for IP addresses * are * on the same subnet. I even put it in one of these subnet calculators just to be absolutely sure.

  One thing that stood out to me, is when I have the controller connected to the network with DHCP on and it automatically 10.158.20.8, he has a strange subnet mask (see image 4 here), I assumed it would be 255.255.255.0 as when I do ipconfig at the command prompt. Could it be the cause of the inconsistency? If so, can I change?

  Also, every time I reset the target thanks to MAX (after the change of the DHCP server to the static IP, or vice versa) MAX does not connect to it again automatically, I have to delete the target and MAX of refreshment and it records again.

  The finals 2 screenshots in the imgur album (found here) are the video output of the controller (just connect a monitor with a VGA cable with an adapter). Picture 5 is what I * currently * see and the last image is a screenshot of old, what it * should * look like. In the first splash screen image, the message "error boot disk program initialization" sticks out, which indicates some kind of hardware malfunction? I don't remember when I see a message like this when I originally set up this system.

  So in summary, I get 'Incompatible IP Settings' - I tried all the usual suspects, all IP addresses are on the same subnet, etc., it seems that there is some * other * problem which is at the origin of the incompatible IP settings that I can not detect. Any help is greatly appreciated, since I have this error I can't install software to the target, which means that I can not install NI-industrial Communications for EtherCAT, aka I can't do anything until I have fix this. Please let me know if there is additional information, that I can provide as well.

  All the best,

  PS, I've created a report to technical support at MAX and it attached in case it is useful for your comments!

  Hey thanks for your reply. The images were in an album of imgur related to the position. I tried actually all to connect to the controller, I made sure that my network card has had to function to automatically detect the crossover (apparently it is the industry standard for Gigabit Ethernet cards). I even managed to try two controllers, a colleague had a spare, and finally the problem turns out to be an incompatibility of the software. I borrowed a laptop of University Department and installed the same software I have on my original laptop and tried to connect to the controller and it worked fine, no incompatible IP settings.

  From there I could say that the problem was related to the original laptop, since settings incompatible IP was not on the borrowed laptop. I actually ended up completely reinstall LabVIEW on the laptop original just in case it was somehow a facility damaged from somewhere. However, I noticed that a colleague had updated the Configuration of the system NOR to 15.0. If I remember, it is usually backward compatibility to the previous 3 versions of LabVIEW, sort of version 15 with a LabVIEW 2012 SP1 works very well. However, during this new LabVIEW installation (before I updated day NOR Sys Config 15) I checked the controller, and I connected to it fine, no errors. Then I installed the version 15 of the Sys Config and * then * got parameters incompatible IP. The better I can understand, is that it is some sort of bug in verses backward compatibility between OR System Configuration 15 on a LabVIEW 2012 SP1 install. That, or it is related to the fact that the controller I use is waaaay out of fashion and unsupported by certain aspects of our days.

  Thanks for your reply anyway, I forgot to post the solution I found here, so I hope that if anyone has this problem, they can check their compatibility of versions and things like that!

• Slide show auto refresh? PLEASE HELP, NECESSARY FOR THE EVENT!

  I want to download images in a folder on my network server and have them come on the other cpu screen savers without having to hit refresh in mode slideshow screen saver. or y at - it a program that will allow me to do this? and who? How? etc.

  You must share the folder of photos with write permissions so that you can copy files to it.
  http://support.Microsoft.com/kb/304040

  What about encouraging them to display on the screen saver, I don't think this is possible without him back on – you can certainly test it to see if it works for sure. If it doesn't work, you can find a different screen saver.

• Cisco 1921 router default password invalid

  Hi all

  I am facing a weird problem where after the reset of the router Cisco 1921, I am trying to connect using the default name "cisco" and the password "cisco".

  and I get the error message no valid password.

  I hard reset the router using the key in the back.

  Can someone help me solve this error. Its frustrating when you can't even connect on a new router

  Thank you!!

  Some devices are configured with the old password. If you log on to these credentials and save the configuration, the default password is cleared. If you have set a new password, you'll end up with an inaccessible area. This avoids the production of devices with the default manufacture password and being exposed.

  You need to do a password recovery procedure.

  (1) connect the console to the device
  (2) turn on the device
  3) press ctrl + break until you are in rommon mode

  Type confreg 0 x 2142 to the rommon 1 > fast to boot from Flash.

  This step allows you to bypass the startup configuration where passwords are stored.

  Type of reset to the rommon 2 > prompt.

  The router restarts, but does not take into account the stored configuration.

  Type no after each Setup question, or press Ctrl-C to skip the initial configuration process.

  Type for the router > prompt.

  You are in enable mode and should see the Router prompt #.

  Because this is a new router without previous configuration is not really necessary to restore the last saved configuration. But if you'd: copy start run

  WARNING: Do not enter the copy running-config startup-config or write. These commands erase your startup configuration.

  Type configure terminal.

  The hostname (config) # prompt is displayed.

  Type enable secret in order to change the enable secret password. For example:

  hostname (config) secret #enable YourPassword

  Restore the previous value of the conf-reg:
  hostname (config) #config - register 0 x 2102

  If you did a copy start run, you must also configure a new user:

  Youruser yourpassword username secret

  And of course: save your configuration

  Do not forget to rate helpful messages ;)

  Sent by Cisco Support technique iPad App

• Help to install a new OS on Cisco router

  Hey all,.

  I recently inherited a Cisco 2620 router, which seems to have been completely flashed/corrupted (see output below), because it can only boot into rommon mode and the "dir" command that all return "bad device name" or a file name of nonsense like "y". Baud unemployment has been altered to 112500 while the tests, normal settings are 9600

  

  Q1) Firstly, I correctly interpret this output?

  My plan is to revive this router with a new IOS ' c2691-adventerprisek9 - mz.124 - 25c.bin "which seem to be taken in charge by the 2600 series.

  However, I do not have:

  a TFTP server

  a USB port on the router

  access to the internet (on the 2620)

  I have:

  The file ' c2691-adventerprisek9 - mz.124 - 25c.bin "on my desktop (Windows 7 PC)

  a connection of the 2620 by using a serial USB RS232 adapter console

  NETGEAR N900 connected to an Ethernet home with a free Ethernet port

  Looking at the above, my conclusion was to use the xmodem command and manually transfer "c2691-adventerprisek9 - mz.124 - 25c.bin" in the directory 'flash' via the serial cable.

  Q2) is xmodem it the best way to revive this router with my resources?

  Finally assuming xmodem is the way to go, I have reviewed the following guide:

  http://www.Cisco.com/c/en/us/support/docs/routers/2600-series-multiservice-platforms/15085-Xmodem-generic.html

  (Q3) is it possible to complete step "3") in the guide above without using hyperterminal (for example using mastic instead)?

  Thanks a lot for your help

  James

  Hello

  You said that you do not have a TFTP server, but you have a computer connected to the Internet.

  I would say to download on your computer (free) tftpd32 because the transfer an IOS via TFTP will be faster than xmodem.

  If you need assistance for IOS via TFTP transfer when in ROMMON, you can consult the documentation of Cisco here: http://www.cisco.com/c/en/us/support/docs/routers/2600-series-multiservi....

  One you download tftp tool and IOS, you can connect the router through copper directly to your switch directly on your computer.

  If you really want to go with xmodem, I use teraterm program to do all the stuff.

  Thank you. Hope this helps

• Problems to start a 3750 X-24 p-S

  I've recently updated firmware in a Cisco C3750X-24 p-S: replaced c3750e-universalk9 - mz.122 - 55.SE3.bin with a c3750e-universalk9 - mz.152 - 1.E.bin.

  Once the switch has been reloaded, there was the following in the console error message:

  'Flash:/c3750e-universalk9-mz.152-1.E.bin' file, unzipped and installed, point of entry: 0 x 3000

  execution of...

  Boot process failed...

  The system is unable to boot automatically. The envirmnment INITIALIZATION variable need to be set on a bootable image.

  switch:

  Command Show boot confirmed that the switch had a boot appropriate pointing to an existing firmware file configuration.

  Suspecting that the new firmware file was damaged, I decided to copy it again. Unfortunatelly the network is not uvailable even after setting all vatiables environment as IP_ADDR etc. When an active device was connected to the ports, there is no light on the same network ports. I decided to copy the firmware via XModem - 1 K. Unfortunately, the process has failed (the switch has been operated and when). Now, the switch would not start at all. I tried the following procedure to enter ROMMON:

  Unplug the power cord.

  Hold the MODE button while you reconnect the power cable from the switch.

  The MODE button is on the left side of the front panel.

  Release the MODE button after the LED above Port 1 x turns off.

  Note: The LED position can vary slightly, depending on the model.

  You are now on the switch: command prompt.

  However Port1 nor any other port comes on or off during the power on procedure: all network ports are empty all the time. Immediately after powing on the switch, SYSTEM light starts flashing green/Orange for about 20 seconds, then turns off for half a second and then starts flashing with green alone indefinitely. As he "boots", some random characters appear in the console. Is it possible to boot into ROMMON mode now?

  You may need to check that someone else has not set speed console X 3750 to some other settings.

  If you have checked all the settings and you can't do anything, then RMA unit.  You should still be able to get coverage out of it.

• Air-cap2702i-a-k9 flashing blue and red, suggestions?

  any suggestions on the question

  Got a air-cap2702i-a-k9 flashing blue and Red

  When I access the console cable

  a: the ap

  command prompt

  Thanks in advance for all

  advice/suggestions

  Hello

  This message means that the AP is in Rommon mode, and he needs to start with the IOS to work properly. In rommon mode you can check variables initialization to next recharge and try reloading the AP. For example, the set command will tell you the next boot image, you must ensure that this underlines the IOS of AP 2700.

  AP: the value

  Boot=Flash:/C1140-k9w7-tar.124-21A.JY

  You can manually set all initialization variables as above, IOS ip address, gateway, and you can also push new IOS image after download of EAC, if it is not an image valid. See the link below to learn more:

  https://supportforums.Cisco.com/document/56156/access-point-ROMMON-RECOV...

  Concerning

  Delphine

  * Please note the useful messages *.

• Ask the Expert

  Hello

  I have a question with our switch main catalyst 4507. a couple of months I had this experience that I can't access my password in my catalyst 4507. i have a password management document. After trying my password assigned for many times that he has been unsuccessful. When I tried using the other reference cisco password, I was able to connect using the password "cisco". for security reasons change us password from time to time, but by regular coins. Just this day, yet once I can't access my password for this device only I also try password by default but not able to connect. My question is, how did this happen? How can I access the configuration of my catalyst 4507 without interruption of service of causes in my network connection. don't forget it's my coreswitch and we are 24 hours a day 7 days a week. Help, please! forward the responses received.

  Thank you and best regards.

  Pete

  Hi Pete,.

  I fear that you will not be able to recover the password without using the ROMmon mode, for which you will need to power cycle the unit which in turn causes a network failure. You will need to make arrangements for a window of maintainace and recover the password.

  I mentioned below the link that gives you the procedure step by step for password recovery:

  http://www.Cisco.com/en/us/products/hw/switches/ps663/products_password_recovery09186a00800945f7.shtml

  P.S.: Please mark this thread as answered if you feel that your query is resolved. Note the useful messages.

  Kind regards

  Sooraj