Cisco 1921 router default password invalid

Hi all

I am facing a weird problem where after the reset of the router Cisco 1921, I am trying to connect using the default name "cisco" and the password "cisco".

and I get the error message no valid password.

I hard reset the router using the key in the back.

Can someone help me solve this error. Its frustrating when you can't even connect on a new router

Thank you!!

Some devices are configured with the old password. If you log on to these credentials and save the configuration, the default password is cleared. If you have set a new password, you'll end up with an inaccessible area. This avoids the production of devices with the default manufacture password and being exposed.

You need to do a password recovery procedure.

(1) connect the console to the device
(2) turn on the device
3) press ctrl + break until you are in rommon mode

Type confreg 0 x 2142 to the rommon 1 > fast to boot from Flash.

This step allows you to bypass the startup configuration where passwords are stored.

Type of reset to the rommon 2 > prompt.

The router restarts, but does not take into account the stored configuration.

Type no after each Setup question, or press Ctrl-C to skip the initial configuration process.

Type for the router > prompt.

You are in enable mode and should see the Router prompt #.

Because this is a new router without previous configuration is not really necessary to restore the last saved configuration. But if you'd: copy start run

WARNING: Do not enter the copy running-config startup-config or write. These commands erase your startup configuration.

Type configure terminal.

The hostname (config) # prompt is displayed.

Type enable secret in order to change the enable secret password. For example:

hostname (config) secret #enable YourPassword

Restore the previous value of the conf-reg:
hostname (config) #config - register 0 x 2102

If you did a copy start run, you must also configure a new user:

Youruser yourpassword username secret

And of course: save your configuration

Do not forget to rate helpful messages ;)

Sent by Cisco Support technique iPad App

Tags: Cisco Network

Similar Questions

Configuration Cisco 1921

I am configuring a Cisco 1921 router to connect with my cable modem. The router gets an IP address from the DHCP server and I can ping resources on the internet on the router. The router distributes DHCP addresses to clients, but clients are unable to access the internet. I'm missing something simple. Here is my config:

R1-1921 #sh run
Building configuration...

Current configuration: 6236 bytes
!
! 19:11:22 EST configuration was last modified Thursday, November 5, 2015 by *.
version 15.3
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
hostname R1-1921
!
boot-start-marker
boot system flash: c1900-universalk9-mz. Spa. 153 - 3.M6.bin
boot-end-marker
!
!
logging buffered 51200 warnings
enable secret 5 $1$ F3oi$ EtowSjpBITAVsWVxr4EDM.
activate the password *.
!
No aaa new-model
No process cpu extended history
No pork process autoprofile cpu
iomem 10 memory size
clock timezone IS - 5 0
clock to summer time EDT recurring
!
!
!
!
DHCP excluded-address 192.168.1.1 IP 192.168.1.100
DHCP excluded-address IP 192.168.1.201 192.168.1.254
DHCP excluded-address 192.168.2.1 IP 192.168.2.100
DHCP excluded-address 192.168.2.201 IP 192.168.2.254
DHCP excluded-address IP 10.10.10.1 10.10.10.100
DHCP excluded-address IP 10.10.10.201 10.10.10.254
DHCP excluded-address IP 192.168.20.1 192.168.20.100
DHCP excluded-address IP 192.168.20.201 192.168.20.254
!
IP dhcp pool vlan2_Home_DHCP
network 192.168.2.0 255.255.255.0
F104.0a0a.140b hexagonal option 43
domain name *.
Server DNS 8.8.8.8 8.8.4.4
default router 192.168.2.254
Rental 7
!
IP dhcp pool vlan10_Home_DHCP
Network 10.10.0.0 255.255.0.0
F104.0a0a.140b hexagonal option 43
domain name *.
default router 10.10.10.1
Server DNS 8.8.8.8 8.8.4.4
Rental 7
!
IP dhcp pool vlan20_Home_DHCP
network 192.168.20.0 255.255.255.0
F104.0a0a.140b hexagonal option 43
domain name *.
Server DNS 8.8.8.8 8.8.4.4
default router 192.168.2.254
Rental 7
!
IP dhcp pool vlan1_Home_DHCP
network 192.168.1.0 255.255.255.0
F104.0a0a.140b hexagonal option 43
domain name *.
Server DNS 8.8.8.8 8.8.4.4
by default-router 192.168.1.254
Rental 7
!
!
!
IP domain name *.
IP cef
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
Crypto pki trustpoint TP-self-signed-2424561219
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 2424561219
revocation checking no
rsakeypair TP-self-signed-2424561219
!
!
TP-self-signed-2424561219 crypto pki certificate chain
certificate self-signed 01
3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
69666963 32343234 35363132 6174652D 3139301E 170 3135 31313032 31383034
35395A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
4F532D53 5369676E 656C662D 43 65727469 66696361 74652 32 34323435 65642D
36313231 3930819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
81008E99 C46CD1DA 4626A4A1 614268 HAS 4 FC70E1B0 66E4D691 6F1DDA9E EE15D3D6
44469CAF D9EB6EAF B155D164 5E75CD1E B0541204 98C7BC8A E973A18A 852F7BC3
09B33BDB C4C63C75 4C8B7A60 BA3BB4E7 C980BDFA 35F50803 C92973F4 19A 90217
48E993E3 BFC1EE4D C9A8ABE7 C094E89B 9629195A 0763605 A D577278C B8C39AB9
010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355 0CEF0203
551 2304 18301680 14B9ECCC A5378EAC C33EA600 3A11948F 56021544 74301 06
03551D0E 04160414 B9ECCCA5 378EACC3 3EA6003A 11948F56 02154474 300 D 0609
2A 864886 05050003 81810046 FC666C70 E65C191B 951D69CC BE68D6D1 F70D0101
B5EC7175 ED432B26 7C44E882 1 C 04F30A7C 006392 E782CB04 CC898FD4 2B5F9085
A84DB5BA 0996408A 46D36AE7 20A4BADA D418EC0D F7A94E46 08782215 C7EEF16F
998E78F0 17026E9A 0705D4F7 FCEEED19 AB467E35 6A8E2CED A35BD0C3 236CF87D
76F3BF78 45D940EF DF0A8934 D411F3
quit smoking

udi pid CISCO1921/K9 sn license *.
!
!
!
redundancy
!
!
!
!
!
property intellectual ssh time 60
!
!
!
!
!
!
!
!
!
interface Loopback0
172.40.59.1 the IP 255.255.255.255
!
the Embedded-Service-Engine0/0 interface
no ip address
Shutdown
No cdp enable
!
interface GigabitEthernet0/0
no ip address
automatic duplex
automatic speed
No cdp enable
No mop enabled
!
interface GigabitEthernet0/0.1
encapsulation dot1Q 1 native
IP 192.168.1.253 255.255.255.0
No cdp enable
!
interface GigabitEthernet0/0.2
encapsulation dot1Q 2
192.168.2.253 IP address 255.255.255.0
No cdp enable
!
interface GigabitEthernet0/0.10
encapsulation dot1Q 10
IP 10.10.10.1 255.255.0.0
No cdp enable
!
interface GigabitEthernet0/0.20
encapsulation dot1Q 20
address 192.168.20.1 255.255.255.0
No cdp enable
!
interface GigabitEthernet0/1
DHCP IP address
no ip redirection
no ip proxy-arp
NAT outside IP
IP virtual-reassembly in
automatic duplex
automatic speed
No cdp enable
!
IP forward-Protocol ND
!
no ip address of the http server
local IP http authentication
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
IP nat inside source list 1 interface GigabitEthernet0/1 overload
IP default-network 192.168.1.0
IP route 0.0.0.0 0.0.0.0 dhcp 20
!
no routing capabilities-Manager service
not run cdp
!
!
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 2 allow to 192.168.10.0 0.0.0.255
access-list 2 allow 192.168.20.0 0.0.0.255
access-list 2 allow 192.168.30.0 0.0.0.255
access-list 2 permit 192.168.40.0 0.0.0.255
access-list 2 allow to 192.168.1.0 0.0.0.255
access-list 2 allow 10.10.20.0 0.0.0.255
access-list 3 Let 192.168.10.0 0.0.0.255
access-list 3 allow 192.168.20.0 0.0.0.255
access-list 3 allow 192.168.30.0 0.0.0.255
access-list 3 permit 192.168.40.0 0.0.0.255
access-list 3 Let 192.168.1.0 0.0.0.255
access-list 23 allow 10.10.10.0 0.0.0.7
!
control plan
!
!
!
Line con 0
exec-timeout 0 0
local connection
line to 0
line 2
no activation-character
No exec
preferred no transport
transport output pad rlogin lapb - your MOP v120 udptn ssh telnet
StopBits 1
line vty 0 4
privilege level 15
local connection
transport of entry all
line vty 5 15
privilege level 15
local connection
transport of entry all
!
Scheduler allocate 20000 1000
!
end
Your modem might need routes to subnets and the NAT configuration for these subnets.

However, another way to do it is NAT CBC all IP addresses to the IP of the interface gi0/1 looks you can try to do.

If you don't then.

(1) you must add 'ip nat inside' to every subinterface

(2) the ACL for your NAT made reference only 192.168.1.x customers while your other ACL refers all subnets.

If you want to have all subnets access the internet turn it into NAT reference one another ACLs

(3) don't know what you're doing with the statement "ip default-network 192.168.1.0.

Just remove it and use the default route you have in your configuration and you don't need to add an ad at the end.

Jon

Cisco 871 routing problem

Hello.

I have a Cisco 871 router with this network diagram

10.218.10.117 host - 10.218.10.118 4 | CISCO 871 | 172.18.122.5-FE0 - 172.18.122.6 host

I want the 172.18.122.6 host can do ping to the 10.218.10.117 host at the other end of the router, but its does not work, what is the problem with this config? could someone give me a hand?

With the help of 1222 off 131072 bytes

!

version 12.4

no service button

horodateurs service debug datetime msec

Log service timestamps datetime msec

no password encryption service

!

hostname ALCALÁ-CNT-UIO

!

boot-start-marker

boot-end-marker

!

enable secret 5 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

activate the password XXXXXXXXXXXXXXX

!

No aaa new-model

!

resources policy

!

IP subnet zero

IP cef

!

!

!

!

!

!

interface FastEthernet0

!

interface FastEthernet1

!

interface FastEthernet2

!

interface FastEthernet3

!

interface FastEthernet4

IP 10.218.10.118 255.255.255.252

automatic speed

full-duplex

!

interface Vlan1

IP 172.18.122.5 255.255.255.0

!

router RIP

redistribute connected

10.0.0.0 network

network 172.18.0.0

!

IP classless

!

!

no ip address of the http server

no ip http secure server

!

Dialer-list 1 ip protocol allow

!

!

control plan

!

!

Line con 0

no activation of the modem

line to 0

line vty 0 4

password XXXXXXXXXXXX

opening of session

!

max-task-time 5000 Planner

end

Better compliance

The f

Jeff,

Each host can ping their side? You have default gateways configured on the hosts?

HTH,
John

Please note all useful messages *.

Cisco 850 routing issues

I am trying to configure a cisco 850 router but I can't do a ping to the outside world of Vlan1. show running-configLooks follow

Current configuration : 5563 bytes!! Last configuration change at 15:33:02 UTC Sat Aug 13 2016 by ciscoversion 15.2no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname fw2.myfw.tld!boot-start-markerboot-end-marker!!logging buffered 51200 warnings!aaa new-model!!!!!!!aaa session-id commonwan mode ethernet!!!ip dhcp excluded-address 10.10.10.1ip dhcp excluded-address 192.168.1.1ip dhcp excluded-address 129.x.x.5!ip dhcp pool ccp-pool import all network 192.168.1.0 255.255.255.0 dns-server 8.8.8.8 8.8.4.4  default-router 192.168.1.1  lease 0 2!         !         !         ip domain name mydomain.tldip name-server 8.8.8.8ip name-server 8.8.4.4ip cef    no ipv6 cef!         !         !         !         crypto pki trustpoint TP-self-signed-1017650632 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-1017650632 revocation-check none rsakeypair TP-self-signed-1017650632!         !         crypto pki certificate chain TP-self-signed-1017650632 certificate self-signed 01  3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030   31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274   69666963 6174652D 31303137 36353036 3332301E 170D3135 30343037 31303536   30375A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649   4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 30313736   35303633 3230819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281   81008B15 A50BCE53 C1A10611 78247737 97E31A5D 653AF401 024B244B F96B48E0   0A1B41EE 16FBFDD1 46F2E1E2 1329D2C6 EEFBCF5B 217DE650 7D2729B0 266008F3   AC4565EA 53D7FA5B 35761F14 6FBDCFAC 24994667 CB0311A9 7FE25580 7D9564C3   BFE10A4A F5F57C4F C4E18EC9 19874BCA 03127F56 252D04B8 9465A23F FBB9045B   D9EF0203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603   551D2304 18301680 146EAE54 B0C95DC2 0561F596 BC47E94B EF80617E F9301D06   03551D0E 04160414 6EAE54B0 C95DC205 61F596BC 47E94BEF 80617EF9 300D0609   2A864886 F70D0101 05050003 81810014 F5B63E51 AD80D4A0 3230E94D 3D1BE457   5D7CF78D 3C911F32 C7238D24 4A8C84D5 D5D4F744 EA2FFD5C 4A40E7A1 A517BFE3   10CC6078 5F446A15 F60EA41E 08C688AF A7834485 0991C739 F3CA38FE CFAA31E2   C72031C1 BAEFA756 719E4903 705C98A7 E20CB004 6FC82D22 D4E62E0C DBA54481   F6A68B3D AA905352 DD76B19F CD4190        quit!         !         username cisco password 0 somepasswordusername admin privilege 15 secret 5 $1$JJZR$kw8yTTHkjUGKIfB8sQiyJ0!         !         controller VDSL 0 shutdown !         ip telnet source-interface Vlan1ip ssh port 2222 rotary 1ip ssh source-interface Vlan1ip ssh rsa keypair-name 1024!         !         !         !         !         !         !         !         !         !         !         !         interface ATM0 no ip address shutdown  no atm ilmi-keepalive!         interface Ethernet0 no ip address shutdown !         interface FastEthernet0 no ip address!         interface FastEthernet1 no ip address!         interface FastEthernet2 no ip address!         interface FastEthernet3 no ip address!         interface GigabitEthernet0 no ip address!         interface GigabitEthernet1 description PrimaryWANDesc_WAN interface ip address 129.x.x.5 255.255.255.0 duplex auto speed auto!         interface Vlan1 description $ETH_LAN$ ip address 192.168.1.1 255.255.255.0 ip helper-address 192.168.1.254 ip nat inside ip virtual-reassembly in ip tcp adjust-mss 1412!         ip forward-protocol ndip http serverip http access-class 23ip http authentication localip http secure-serverip http timeout-policy idle 60 life 86400 requests 10000!         !         ip dns serverip nat inside source list nat-list interface GigabitEthernet1 overloadip route 0.0.0.0 0.0.0.0 GigabitEthernet1!         mac-address-table aging-time 15no cdp run!         !         !         banner exec ^C% Password expiration warning.-----------------------------------------------------------------------

Cisco Configuration Professional (Cisco CP) is installed on this device and it provides the default username "cisco" for  one-time use. If you have already used the username "cisco" to login to the router and your IOS image supports the "one-time" user option, then this username has already expired. You will not be able to login to the router with this username after you exit this session.

It is strongly suggested that you create a new username with a privilege level of 15 using the following command.

username <myuser> privilege 15 secret 0 <mypassword>

Replace <myuser> and <mypassword> with the username and password you want to use.

-----------------------------------------------------------------------^C        banner login ^C-----------------------------------------------------------------------Cisco Configuration Professional (Cisco CP) is installed on this device. This feature requires the one-time use of the username "cisco" with the password "cisco". These default credentials have a privilege level of 15.

YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE  PUBLICLY-KNOWN CREDENTIALS

Here are the Cisco IOS commands.

username <myuser>  privilege 15 secret 0 <mypassword>no username cisco

Replace <myuser> and <mypassword> with the username and password you want to use.   

IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.

For more information about Cisco CP please follow the instructions in the QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp -----------------------------------------------------------------------^C        !         line con 0 no modem enableline aux 0line vty 0 4 access-class 23 in privilege level 15 transport input telnet ssh!         scheduler allocate 60000 1000!         end

I am connected via the port console of the router and can ping the outside world only from port GigaEthernet1 whose IP address129.x.x.5

Clients that connect on VLan1 get IP addresses in the range of 192.168.1.0/24 and these clients can ping each other, the gateway that is 192.168.1.1 and the GigaEthernet1 that has the intellectual property129.x.x.5

What's not in this case? Any suggestion is appreciated the most.

@[email protected] / * /;

Thanks for your post. I had a look at your configuration, and it is great that you are a few short steps on your NAT is why it does not work. Please follow the steps below in order to get this work properly.

1. first of all, let us remove the old configuration NAT then back to a clean slate with the following commands.

no ip nat inside source list nat-list interface GigabitEthernet1 overloadclear ip nat translation *

2. now, we will create a list of access control allows for NAT traffic and create the new NAT statement for that tie together. * NOTE: If the version of IOS, you are running requires mask rather than generic then change 0.0.0.255 to 255.255.255.0.

access-list 100 permit ip 192.168.1.0 0.0.0.255 anyip nat inside source list 100 interface GigabitEthernet1 overload

3. the next step is to specify the logical role of the interfaces in question, whether they are 'inside' or ' outside'.

interface vlan1 ip nat inside exitinterface GigabitEthernet1 ip nat outside exit

4. Finally, save us the configuration and reload.

copy run startreload

After the unit is returned as a result of charging, please try again. In some cases - depending on the version of the IOS, you have to ping the outside world from a computer on the local network rather than just sourcing of the interface VLAN. Try this back and forth, and let me know how get you there. I can't wait to hear back.

Kind regards

Luke Oxley

Please evaluate the useful messages and mark the correct answers.

Cisco 1921 - how to configure VPN multiple Tunnels to AWS

I have a router VPN Cisco 1921. I managed to create tunnel VPN Site to Site with AWS VPN Tunnel 1. AWS offers 2 tunnels, so I created another card Crypto and attaches to the existing policy. But the 2nd tunnel won't come. I don't know what I'm missing... is there a special setup that needs to be done to allow multiple IPsec vpn tunnels on the same physical interface? I have attached a picture and included the configuration of my router, if it helps.

VPN - 1.jpg

C1921 #sh run
Building configuration...

Current configuration: 2720 bytes
!
! Last configuration change at 02:12:54 UTC Friday, may 6, 2016, by admin
!
version 15.5
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
hostname C1921
!
boot-start-marker
boot-end-marker
!
!
logging buffered 52000
enable secret 5 $1$ jc6L$ uHH55qNhplouO/N5793oW.
!
No aaa new-model
Ethernet lmi this
!
!
!
!
!
!
!
!
!
!
!
!
Research of IP source-interface GigabitEthernet0/1 domain
IP cef
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
!
license udi pid CISCO1921/K9 sn FTX1845F03F
!
!
username admin privilege 15 password 7 121A0C041104
paul privilege 0 7 password username 14141B180F0B
!
redundancy
!
!
!
!
!
!
!
crypto ISAKMP policy 10
BA aes
preshared authentication
Group 2
lifetime 28800
ISAKMP crypto keys secret1 address 52.35.42.787
ISAKMP crypto keys secret2 address 52.36.15.787
!
!
Crypto ipsec transform-set AWS - VPN aes - esp esp-sha-hmac
tunnel mode
!
!
!
map SDM_CMAP_1 1 ipsec-isakmp crypto
Description Tunnel 1 to 52.35.42.787
defined by peer 52.35.42.787
game of transformation-AWS-VPN
PFS group2 Set
match address 100
map SDM_CMAP_1 2 ipsec-isakmp crypto
Description 2 to 52.36.15.787 Tunnel
defined by peer 52.36.15.787
game of transformation-AWS-VPN
PFS group2 Set
match address 100
!
!
!
!
!
the Embedded-Service-Engine0/0 interface
no ip address
Shutdown
!
interface GigabitEthernet0/0
Description connection Wan WAN - ETH$
IP address 192.168.1.252 255.255.255.0
automatic duplex
automatic speed
map SDM_CMAP_1 crypto
!
interface GigabitEthernet0/1
Description of the connection to the local network
IP 192.168.0.252 255.255.255.0
automatic duplex
automatic speed
!
IP forward-Protocol ND
!
IP http server
local IP http authentication
no ip http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
IP route 0.0.0.0 0.0.0.0 192.168.1.254 permanent

!
recording of debug trap
host 192.168.0.3 record
host 192.168.0.47 record
!
!
Note access-list 100 permit to AWS Tunnel 1
Access-list 100 CCP_ACL category = 20 note
access-list 100 permit ip 192.168.0.0 0.0.0.255 any what newspaper
Note access-list 101 permit to AWS Tunnel 2
Note access-list 101 category CCP_ACL = 4
access-list 101 permit ip 192.168.0.0 0.0.0.255 any logexit
!
control plan
!
!
alias con exec conf t
SIB exec show int short ip alias
alias exec srb see the race | b
sri alias exec show run int
!
Line con 0
exec-timeout 0 0
Synchronous recording
line to 0
line 2
no activation-character
No exec
preferred no transport
transport output pad rlogin lapb - your MOP v120 udptn ssh telnet
StopBits 1
line vty 0 4
privilege level 15
local connection
transport of entry all
transportation out all
!
Scheduler allocate 20000 1000
!
end

There should be no second tunnel.

I use either a peer or the other, but not both at the same time.

To display both at the same time, you need to use the Tunnel interfaces. Amazon would have you sent pretty much the exact commands to copy and paste into.

Cisco 2611 router and RADIUS

Greetings. First of all, let me start by saying that I am a fool, I know I am a fool and I apologize for wasting everyone's time. In fact, I do RTFM, RTFMs a lot, and I've yet to find a resolution.

Secondly, I am setting up a RADIUS server in my test network. I installed Yopougon RADIUS on a Windows 2000 System. I have the following Setup on my Cisco 2611 router:

With the help of 2297 off 29688 bytes

!

! 17:20:27 PDT configuration was last modified Tuesday, May 20, 2008

! NVRAM config update at 17:20:29 PDT Tuesday, May 20, 2008

!

version 12.1

no single-slot-reload-enable service

horodateurs service debug datetime localtime show-timezone msec

Log service timestamps datetime localtime show-timezone msec

encryption password service

!

host Tester name

!

logging buffered debugging 10000

AAA new-model

RADIUS AAA server group RadiusServers

ACCT-port of the server 172.26.0.2 auth-port 1812 1813

!

Group AAA authentication login default local RadiusServers

AAA authentication login local localauth

AAA authentication ppp default if necessary to group local RADIUS

AAA authorization exec default local radius group

RADIUS AAA authorization network default local group

AAA accounting delay start

start-stop radius group AAA accounting exec by default

start-stop radius group AAA accounting network default

AAA process 6

Select the secret xxx

!

test username password xxx

!

clock timezone PST - 8

clock summer-time recurring PDT

IP subnet zero

no ip domain-lookup

!

no ip bootp Server

!

interface Loopback0

the IP 192.168.0.1 255.255.255.0

!

interface Ethernet0/0

Description for the main network

address IP X.X.X.X 255.255.255.128

no ip redirection

no ip unreachable

no ip proxy-arp

NAT outside IP

full-duplex

No cdp enable

!

interface Ethernet0/1

Description of network internal

IP 172.26.0.1 255.255.255.0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

load-interval 30

full-duplex

No cdp enable

!

IP nat pool test X.X.X.X-X.X.X.X netmask 255.255.255.128

IP nat inside source list 3 pool overload test

IP nat inside destination list 3 pool test

IP classless

IP route 0.0.0.0 0.0.0.0 X.X.X.X

no ip address of the http server

!

radius of the source interface Ethernet0/1 IP

access-list 3 permit 172.26.0.0 0.0.0.255

not run cdp

public RO 15 SNMP-server community

secret key of acct-port 1812 auth-172.26.0.2 - RADIUS server host port 1813

RADIUS server retransmit 3

key secret RADIUS server

!

Line con 0

password xxx

Synchronous recording

line to 0

line vty 0 4

access-class 10

1234567890 7 password

Synchronous recording

!

NTP-period clock 17208108

Server NTP 192.43.244.18

end

My RADIUS server is in place and respond to queries, but my router does not seem to be transferring applications to authenticate to it. In fact, when I connect to the router using HyperTerminal, it expires, and I find myself authenticate locally.

I don't really like if my Cisco equipment authenticates with the RADIUS server, but I have to get set up to authenticate my users so that I can follow their time online. What I missed in my router configuration? Therefore no transfer requests to the RADIUS Server user authentication.

Thanks for any assistance, you may be able to provide.

If you explore the authentication Proxy and it works, it could make you forget the PPPoE fast enough.

If you decide to pursue PPPoE, the following link is probably where you will find most of the information on the configuration of Cisco PPPoE:

http://www.Cisco.com/en/us/Tech/tk175/tk819/tsd_technology_support_protocol_home.html

"Providers" of Cisco forums could provide some guidance if PPPoE is achievable with your platform and environment?

Cisco Wireless router model WRT120N guard give up Internet connection

My wireless router will work for 6-8 hours, and then remove the connection to the internet. I switch the modem and the router several times to re-establish the connection. I'm also using a Netgear Access Point.

I use:

Charter high-speed Internet

Motorola Modem

Model Cisco WRT120N router

Parameters

Mixed-mode

Channel Auto width - 20 MHz or 40 MHz

Security - Personal WPA2

Disabled SSID broadcast

Firmware Version v1.0.04

Automatic connection Type - Conf DHCP

Beacon interval - 50

Fragmentation threshold 2304

RTS threshold 2304

All other settings are default.

When I unplug the modem to the router and plug it on the desktop I have internet service.

The connection is also falling only on wired or wireless?

Try to update the firmware on your router.
Connect to the computer with the Ethernet cable to the router.
Download the latest firmware from the site Web of Linksys and save it to your computer. Open the router configuration page. Click the Administration tab and switch to the sub tab upgrade the Firmware through the firmware file that you have already downloaded and update on your router.
After upgrading the firmware on the router, it is recommended that you must reset the router and reconfigure. Press and hold the reset button on the router for 30 seconds. Release the reset button and wait 10 seconds. Power cycle the router and reconfigure.

Cisco 1921 / K9

Hi all

1: my Corp Office, I installed a K9 Cisco 1921, I want to know that how IPSec VPN Tunnel Cisco 1921 /k9 can support and what is the IPSec VPN throughput?

2: I have connected a link bandwidth (150 Mbit/s Download and 25 Mbit/s upload) to my Cisco 1921/K9, I want to know if Cisco 1921/K9 is able to manage bandwidth 150Mbps?

3: If one of my retail site runs on 10 Mbps of bandwidth on Cisco RV220W connect to Cisco 1921/K9 for the Corp. Office. How much bandwidth IPSec tunnel will use?

4: I have 200 points of sale and each have 5 computers, wifi and son (Mix few are on wifi and little are wired) that is block to install to the location of the retail of Cisco RV325 Cisco RV220W or 3.

Thank you

Sandy

For retail locations, I would watch the series 880 s. They are available with built-in ADSL/VDSL modems and also wireless. The WIFI network can be controlled by a WLC.

Management is the reason why I use RV-devices. As far as I know, they have still any IOS-like. The AP can be controlled with a WLC which also makes very easy to manage.

For the router to 4000, I know that what is stated in the data sheet and the part of the config guide of license (the last router Cisco 4000 I used performed a decade... ;-)).

But there are more feature-licenses like DRY/SSEC you need.

It seems that the performance is entirely controlled by the license and the 100 / 300 Mbps is the performance of the services. But without the HSEC license, you are limited (as for many cisco routers) to 85 Mbps encrypted 225 tunnels and bandwidth.

Sqlplus cannot log in with the default password
Hello

I tried to log in as a user I in order to run a script (I read that the default password is the same as the schema name I in this case), but it gives the error:

SQL > connect
Enter the user name: I
Enter the password:
ERROR:
ORA-01017: name of user and password invalid. connection refused

Any ideas what could be the default password, or how to change it as sysdba?

Thank you
Please see category 6 in these docs. Schema (ABM... product passwords ZX) must be changed using FNDCPASS.

Configuration Guide for Oracle E-Business Suite 11i [ID 189367.1]
Configuration Guide for Oracle E-Business Suite Release 12 [403537.1 ID]

Thank you
Hussein

[nQSError: 43126] Failed authentication: username/password invalid, how to avoid?
Hello

I met following error: [nQSError: 43126] failed authentication: username/password invalid.
When I started weblogic server and server used in the judgment.

After poking around on the net, came across this blog: http://obiee11gqna.blogspot.com/2011/09/obiee-11g-errors-nqserror-43113.html

Find password for MDS & BIPLATFORM has 'expired', managed to solve my problem and my presentation Services have been up & running.

My question is, how to avoid the password SDM & BIPLATFORM to have expired in the future?

Kind regards
Jitendra
Hi Jitendra,

Check it out, http://www.artofbi.com/index.php/2011/03/oracle-11g-rdbms-password-expiration-default-possible-impact-on-obi-11g/

Rgds,
DpKa

Name of user and password invalid connection denied
Hi all
I installed the Oracle 11 g server and I use forms 6i oracle as front end. while I tried to connect my application to 11g I get the message name to username/password invalid connection refused
After I get my application open but while I am trying to open each form in an application, I get this message. Is any particular setting in oracle 11g.

Thanks in advance
Aneesh
By default, Oracle 11g passwords are case-sensitive: make sure you use the correct case of password.

ReadyNAS Ultra 6 OS reinstall appears to have not reset admin default password

I had my ReadyNAS Ultra admin access, but went to test the admin password recovery tool to ensure that the program was configured ok. The recovery email was never received, and test the recovery nuked tool the password admin defined earlier. So I lost my ReadyNAS Ultra 6 admin access.

I have more of these procedures for a reinstallation of the OS:

http://KB.NETGEAR.com/app/answers/detail/A_ID/22818

http://KB.NETGEAR.com/app/answers/detail/A_ID/21107

The operating system reinstall appers to have updated the FW according to display NAS, but I can not connect with credentials "admin" and "password" even after that.

I can always go up the SIN of my network. I don't have admin access any longer.

What should try this item to retrieve the ID of the admin?

Try the default password "netgear1" (without the quotes). "password" is the default password for OS5/OS6, not for OS4.

Revo Center RC111 default password

Is there any user/owner Revo Center RC111-ER10H Windows Home Server 2011 there?

I've lost my restore disk and could not remember the admin password.

Anyone remember what is the default password?

Thanks to a bouquet.

Yes, I try really, really hard, but could not still remember.

But my wife said something that bring back old memory. From there on, the attempts of fourth said.

Thank you

HP LaserJet MFP M127fn Pro: How to reset the password or what is the default password

I have a M127fn of MFP HP LaserJet Pro, I can't access the menu, he continues to ask for a password and for the life of me I'm not rember defining one. Is there a way to reset it and if so what is the default password.

Thank you

Hello

Please see the sent private message now.

You can see by clicking on the icon of the envelope at the top right of this page

LAN does not work when the Cisco E1000 router hangs

Original title: Download sp3

Remember - this is a public forum so never post private information such as numbers of mail or telephone! I bought recently a new Cisco E1000 router. My computer is a laptop model Lenovo 0769.

I am running windows XP with sp2. The cisco software requires sp3. I called support of cisco and even they couldn't get to download sp3. My network is wireless on the router and I had to install from another laptop computer on the system. My LAN does not work when hooked. What do you suggest to me.

Ideas:
- You have problems with programs
- Error messages
- Recent changes to your computer
- What you have already tried to solve the problem
Hi mdenrique,

1. what exactly do you mean by LAN (Local Area Network) does not work? You get the error message?

If you have not installed Service Pack 3, try the following steps:
Step 1: Download Service Pack 3
see How to obtain the latest Windows XP service pack .
b. scroll the window and click on "Download now the Windows XP Service Pack 3 package" to download the service pack.
c. save the file on the desktop.

Step 2: Install Service Pack 3
a. open the file downloaded and follow the instructions in the wizard to complete the installation.
b. restart the computer once the installation is complete.

For more information, see steps to take before you install Windows XP Service Pack 3

Note: Once you have installed service pack 3, install the router and check if the problem persists.

Step 3: To troubleshoot LAN, run home and small Office Networking Troubleshooter
a. Click Start and then click Help and Support.
b. under Pick a help topic, click Network and Internet.
c. under network and the Web, click on resolution of networking or Web problems and then click on home and small Office Networking convenience store.
d. answer the questions in the troubleshooter to try to find a solution.

For more information, see the following articles:
1 see How to troubleshoot a network in Windows XP
2 see two resources to solve the problems of connection network in Windows XP

Visit our Microsoft answers feedback Forum and let us know what you think.