A loop of reboot after upgrade

Similar Questions

• loop of reboot after upgrade to 9.3

  Hello

  I did the upgrade to 9.3 this morning and my curls by restarting since phone. I only see a black screen with a white head and a white screen with a black Apple. Even a hard reset (Home button + button for 10 seconds to STOP) has not solved the problem.

  Some may see this behavior as well?

  BR

  Florian

  If the update did not complete properly, put your phone in recovery mode and restore with iTunes.

  If you are unable to update or restore your iPhone, iPad or iPod touch - Apple supports

• Satellite C660 stuck in an infinite loop of BSOD after upgrade to win 10

  Wow what a disaster, this is a machine under windows 7-32 bit Satellite C660 PSC1GA-01E01M stuck in an infinite loop of BSOD.

  The lappy said that it was ok to upgrade to windows 10 so... Yes, I did.
  Now its stuck in a loop without end of BSOD.

  So I decided to use the recover option and reinstall windows 7 and then move from there.
  After mega downloads updates and finally got to the stage where there was no update on the left to get, so I decided to upgrade to windows 10 even once.

  Now stuck in an endless loop of BSOD again.

  Can someone point me to the driver who is a failure, I can get into SafeMode ok, Device Manager has 2 problems

  (1) is under OTHER DEVICES is an unknown device
  (2) is generic pnp monitor

  I tried from Toshiba Web site for updates of drivers for 32-bit windows 8 thinking this could be the best step but the links are bad and the page Web said sorry loser at home...

  Also no network, if I try to logging for the safe mode with networking, he returned to the screens of BSOD...

  HELP PLEASE

  Toshiba has released a list with all Toshiba models supported for upgrading to Windows 10
  http://win10upgrade.Toshiba.com/swup...SPX?region=TEG

  Satellite C660 PSC1GA is not in the list, which means that this model is not supported to win 10 and will not get win 10 drivers.

  However the Win 10 must run on this device, because it meets the essential physical requirements.

  I guess the BSOD loop arise due to some drivers which are not entirely compatible Win 10 and probably these drivers must be removed before making the Win 10 update.

  To check the compatibility follow this procedure:

  • Right-click on the icon 'Get Windows 10' (on the right side of the taskbar), then click on "Check the status of your upgrade".
  • In the app to get Windows 10, click on the menu: (3 lines) and then click on "Check your PC.
  • Now you should see the list of compatibility issues

  Also this kind of problem could be fixed by Microsoft update, as mentioned in this article:
  http://www.Forbes.com/sites/amitchow...s-reboot-loop/

• loop of reboot after trying to reinstall sp2

  I have a 7550 Presario with Windows XP, which has been updated at least SP2 and IE8... after the infamous 10 updates / 02 / 10, my computer to bike to the safe mode screen... I couldn't get Mode safe, instead, she would simply keep a backward loop.

  Had no other choice than to go into the system recovery, which, after a reboot reloaded a problem so that I got a year - does not allow me to open the program files.
  I went in Safe Mode, once again, right Clicked Program Files and changed ownership to me (to another profile named Administrator, with 's'. This re - enabled me to open files.

  Finally rebooted, but the SP1 and the best Windows I have now is IE6.

  If I try to download the basics of security, then SP2, I get an error indicates a Windows file is damaged or missing after SP2 install - I return to the loop to restart, the screen of "Presario" factory, giving me the choice (or chance) to make a recovery of the system (F10).

  Because after the recovery, I was still able to get safe mode and the Console recovery (but NOT from a boot disk) I tried the fix posted from the WINDOWS command line /: CHDIR $NtUninstallKB977165$ \spuninst - then - BATCH spuninst.text - then - exit

  It sent me to the loop to restart with the option "Presario" of output or F10 Recovery (research so that he went to loading Windows for about 5 seconds).

  I am currently in SP1 and IE6 that presents only the basic features, but is extremely unstable (tempremental).

  Norton has been deleted, so all the other preloaded junk factory.

  I noticed that I have about 20 "WINDOWS XP PATCHES including abot 6 or 7 containing (SP2) in their name" in the Remove programs in the control panel section. I have not deleted one of these.

  Can anyone help?

  I would back up all your important data so that you are always been lucky, and then perform a reinstall of the OS, etc.. It appears from your description, that you have made a resumption of non-destructive control that allows at least back up your files, etc. before doing a complete restoration.

  I know that's not what you want to hear. TaurArian [MVP] 2005-2010 - Update Services

• Computer goes to a loop of reboot after Windows update

  After a complete restoration of the PC, tried to install the update to windows, my computer goes to a restart and stuck loop installation of updates stage 3 of 3 so went ahead and made a factory again restore but the windows updates causing the problem, it is stuck in a reboot loop suggestions. Is it because of damaged hard drive files?

  Perform a restart from a hard stop. Press the f8 key until you get to the screen asking questions on safe mode. Select repair. Then, you should find a system restore option. Select it. Spend until it gives you a choice of dates, then select a date before the update. This worked like a charm and does not lose any data. Turn off your automatic installation of updates option.

• SG500-52 infinite reboot after upgrade

  I tried to upgrade my passage to the new version of code and firmware of the boot, but the device is now in an infinite reboot loop, does not respond to the connection of the serial console and will not be reset to the original image when I press and hold the reset button.

  How can I get my switch back?

  Hi Brendan,

  There's not much you can do without access to the switch. Please make sure that when you test the switch is not connected to the network where the cause of the problem is related to network traffic.

  You should be able to get the connection console if:

  1 speed is fixed at 115 200 baud

  2. using the serial cable that was in the package

  Kind regards

  Alkesandra

• RESOLVED: Loop of reboot after installing new disks in RAID of PERC S100

  A customer has a Dell T110 (with a PERC S100 RAID controller) running Windows 2008 R2. The system has two disks: a reader not RAID (C :) running the operating system and a RAID1 drive (E :) sharing data with network folders.) We need to install again, larger disks for the RAID.

  I thought I could backup the data on the RAID drive existing (e), install new disks, built a new table in the S100 (VDM) virtual disk boot manager, boot into the operating system, create the new partition for the data replaced E: drive and copy the data back. This was not the case. After installing the new disks and the new array of construction (which is reported as "READY (R/W)" when starting, Windows starts all the way in "press CTRL-ALT-DEL to log". After two or three seconds, the system reboots. The same thing happens when I try to start safe mode. The system IS NOT automatically booted to the Recovery Console. He never seems to know that an error occurred and the system was not shut down normally.

  I booted into the Recovery Console, installed the drivers for the PERC S100 and run recovery to start without success. Also in the Recovery Console, I ran 'chkdsk /f E:\. ' (remarkably, the drive letter for the data drive remained the same), and no error has been reported. I also reinstalled drivers S100 of the recovery using DISM Console, but that changed nothing.

  I started to 8.1 Windows PE, installed drivers S100, formatted the virtual disk, copied the data which he, and everything works fine. The only problem is when I try to boot from the system drive (which has no problem) with the new installed disks.

  When I put the old records, the system boots normally with no reconfiguration required. The VDM to start automatically remembers the discs and the table. Nothing shows up in the logs event indicating that there was an error during startup. (Ntbtlog.txt) start-up newspaper, after several boots with the new drives in place, indicates that the system restarts at various times during loading drivers. There is nothing coherent in the startup log to indicate what the problem is.

  The only clue I have is that, during the startup, the VDM reports the virtual drive of origin as 'NORMAL (R/W)' and the new virtual disk as "READY (R/W)", but I'm not sure of the significance of this difference or if it suggests a solution.

  I can't find clues in all the newspapers about what may be the problem. If anyone has any suggestions, I will be grateful. I'll be especially grateful for the wacky suggestions.

  I ran it. Nothing appeared unusual. However, I does not solve the problem.

  I connect the new readers to the same SATA ports as the old records. When I connect one of them to the SATA port that had not been used as part of the original painting, the VDM S100 reported the original failed array, because readers were is more connected and showed the new table as a LOAN. The operating system then started normally.

  The trick, it seems that you should remove the old virtual disk before connecting the new disks on the same ports.

• Satellite P500 - loop of reboot after using the Toshiba Recovery disk

  Hello

  I have a problem recovery SATELLITE P500. I did the recovery disks. It starts ok on the recovery disk and format the hard drive and copy the disks to the hard drive. Then, he begins installing windows and restarts.

  He then goes to a loop
  (1) marketing and says "Setup is preparing your computer for first use.
  (2) Toshiba banner saying please wait... Second installation may take several minutes. Pleae do not interrupt or shut down the computer!
  (3) Windows logo
  (4) close...
  (5) restarts and goes to 1)

  It would be great if someone could help me with this.

  Thank you very much
  Softari

  Hello

  I noticed the same thing on my Satellite P500, but I must say it s not a problem, it of quite normal. The computer will restart several times (10 times or more) to complete the installation.

  You know that a lot of drivers/tools will be installed and some restart is required to configure everything properly.

  So don t interrupt the installation of recovery, just wait a little longer and a coffee. Everything is done automatically and your laptop is reinstalled with the factory settings. :)

• MacBook pro stuck on reboot after upgrade

  Try to install the 10.11.4 last updated on 2015 MacBook pro. All went well until the reboot. Status is stuck slightly more at halfway, I'm afraid to stop - but it has been in the same place for more than an hour (white bar just above the "n" in "restart")

  Never mind.  Powered down, rebooted and it seems to work very well.

• loop of reboot after update

  Windows Server 2008 R2 - after you install an update, the server restarts, says it is to complete the update and then restarts again and forever.

  Hi Michael,

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  Hope this information helps.

• Endless loop of reboot after Win Update. How can I get out of it?

  I just ran Windows Update to update my Acer 3680 running Vista Basic. Downloaded 33 installed files some, then went into a reboot.  The computer keeps indicating "configuration of updates: Stage3 3-0% complete.". Do not turn off your computer. ', then turn around and restarts in the same message.

  I suspect tries to run a corrupt file, it cannot go beyond enforcement of the boot file which has been modified to run it.  F8 boot options (safe mode, etc.) just go back to the same thing.

  Hi Lmmohr,

  ·         You are trying to install updates?

  Try the procedure described in the following article:

   

  An update is not installed successfully when you try to install the update in Windows Vista and Windows 7

   

  http://support.Microsoft.com/kb/949358

  I hope this helps.

• Loop Finder crash after upgrading to El Capitan.  'Finder close unexpectedly when you use the plug-in finder' - the message really is in Norwegian, so it may be different for the English operating system.

  'Finder close unexpectedly when you use the plug-in finder' - the message really is in Norwegian, so it may be different for the English.  The e is a compatibility issue with dropbox or Google drive in El Capitan?  Those are the plug-ins only that I could find.  Thank you very much.

  Please launch the Console application in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  Step 1

  For this step, the title of the Console window should be all Messages. If it isn't, select

  SYSTEM LOG QUERIES ▹ all Messages

  in the list of logs on the left. If you don't see this list, select

  List of newspapers seen ▹ display

  in the menu at the top of the screen bar.

  In the upper right corner of the Console window, there is a search box to filter. Enter the name of the application crashed or process. For example, if Safari has crashed, you would enter "Safari" (without the quotes).

  Each message in the journal begins with the date and time when it was entered. Select the messages since the time of the last fall, as appropriate. Copy to the Clipboard by pressing Control-C key combination. Paste into a reply to this message by pressing command + V.

  The journal contains a large amount of information, almost everything that is not relevant to solve a particular problem. When you post a journal excerpt, be selective. A few dozen lines are almost always more than enough.

  Please don't dump blindly thousands of lines in the journal in this discussion.

  Please do not post screenshots of log messages - text poster.

  Some private information, such as your name, may appear in the log. Anonymize before posting.

  Step 2

  In the Console window, clear the search box, and then select

  DIAGNOSIS AND diagnostic USE information reports ▹ user

  (not diagnose them and use Messages) in the list of logs on the left. There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points downwards. You will see a list of reports of incidents. The name of each report begins with the name of the process and ends with ".crash". Select the most recent report on the process in question. The content of the report is displayed at right. Allows you to copy and paste to validate all of the content, text, not a screenshot.

  I know that the report is long, perhaps several hundred lines. Please report all this anyway. If the report is only a few lines, make sure that you have disabled the search box.

  If you don't see any report, but you know, he had an accident, you have chosen diagnostic and using the list of Log Messages. INFORMATION on the USE of DIAGNOSTIC AND choose instead.

  In the interest of privacy, I suggest that, before posting, you change the UUID ' anonymous, ' a long string of letters, numbers and dashes in the header of the report, if it is present (it cannot be). "

  Please do not post other types of diagnostic report - they are very long and rarely useful.

  When you post the journal excerpt or the accident report, you might see an error message on the web page: "you have included content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the forum software. Thanks for posting the text on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

• After upgrading Office 2003 to Office 2010, when rebooting, open a window of choce of windows update, if you select do not do updates, wauclt.exe runs and the pigs, cold start pc is required

  After upgrading Office 2003 to Office 2010, when rebooting, open a window of choce of windows update, if you select do not do updates, wauclt.exe runs and the pigs, cold start pc is required to restart or allow time (about an hour) for wuauclt stop execution and free PC - our aim here is to bundle 2010 via ZEN na enter the beam perfectly - this popup must be eliminated

  Hi Pops1148,

  ·         Is the question not confined with updated Microsoft Office?

  Follow the suggestions below for a possible solution:

  Method 1: You can follow the steps in the article in the Microsoft Knowledge Base and check if it works.

   

  Troubleshooting Windows Update or Microsoft Update when you are repeatedly offered an update

  http://support.Microsoft.com/kb/910339

  Method 2: Try the SFC (System File Checker) scan on the computer.

  To run the System File Checker tool, follow these steps:

  a. click Startand type cmd in the box start the search .

  b. right click on cmd in the list programs, and then click run as administrator.

  c. If you are prompted for an administrator password or a confirmation, type your password or click on continue

  d. at the command prompt, the following line and press ENTER:

  sfc/scannow

  Reference:

  Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)

  http://support.Microsoft.com/kb/310747

   

  File system (CFS) Checker

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/system_file_checker.mspx?mfr=true

  Method 3: I also suggest that you scan your computer with the Microsoft Security Scanner, which would help us to get rid of viruses, spyware and other malicious software.

  The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.

   

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

   

  Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

  Important: While hard disk analysis if bad sectors are found when scanning try to repair this area, all available on which data can be lost.

  Let us know if that helps.

• Loop of reboot upgrade Vista to stage 3 of 3

  Hello. Problems after upgrade to Windows Vista (Ultimate). He stops at the step 3 of 3, 75%, then restarts over and over again. I tried to restart in integrated security mode and I tried to restart in the last known configuration that worked - nothing helped.

  I hope someone can help - thank you

  "Of the problems after an upgrade of Windows Vista (Ultimate). He stops at the step 3 of 3, 75%, then restarts over and over again. »

  You haven't really done the upgrade.

  http://Windows.Microsoft.com/en-AU/Windows-Vista/products/system-requirements

  Vista system requirements.

  Vista Upgrade Advisor is no longer available from Microsoft to see what the cause of the problem!

  You do the upgrade of a Vista operating system?

  Try disabling/uninstalling your antivirus.

  And just as mouse, keyboard and screen connected.

  See you soon.

  Mick Murphy - Microsoft partner

• Problems syncing notes app after upgrading to iOS 10

  Hi all

  I hear a lot of people having the same problem on the web.

  After upgrading my iPhone 6 s more and iPad Pro iPad 9.7 ", kept perfect notes that I saved in the Notes application (like my MBP / iMac too), while on my iPhone, I've known many sync problems and even lost notes and records.

  1. I tried to pass and on the synchronization of Notes in the iOS iCloud preferences, with a reboot between stocks. Nope. No synchronization, and when I turned on sync I lost almost all of the notes previously saved in my iPhone, so I now 15 notes instead of 175. This ONLY happens on my iPhone, while iPad / MBP / iMac yet.

  2 - I tried to create a new folder in my MBP or in my iMac, hoping to "stimulate" a new event to Resync through all my devices. Not for the iPhone, but synchronized on my iPad / MBP / iMac.

  3. today, I made a backup of my iPhone, reinstalled the iOS 10, then restored the backup.

  Nope.

  Any ideas, guys?

  Thank you

  Luca

  EDIT: actually sync problems seems to occur exclusively on the side of the iOS. This also includes the iPad. Fortunately, I didn't have the great idea to disable the synchronization of Notes in iCloud on my iPad, as I did on the iPhone.

  I'd lose certainly all currently stored notes in my iPad too.