loop of reboot after trying to reinstall sp2

Similar Questions

• Computer Toshiba laptop does not start after trying to install SP2 for vista 32 bit

  Tried to install SP2 for vista updates, it stagnates at 12%, message saying a problem has been detected and windows has been closed to protect the computer. At the bottom of the error message screen, it reads, technical info-stop OXOOOOC1F5. Windows doesn't start at all now, has tried running safe mode, pilots seem to load, then it returns to the screen error message with the same problem said. Nothing seems to work, tried same recovery disk came with the computer, it says it is loading files, then it returns also to error message screen. Computer came with vista pre-installed, so I don't have this drive to try. Someone at - it solutions? Very frustrating, how do I search problem when the computer will not start at all? Help!

  Follow the info below to try a Startup Repair:

  As is the case with most computers/laptops these days, they do not come with good Vista disc to repair only the recovery disks.

  If yours falls into the category above, download the ISO on the link provided and make a bootdisk of it.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  You can make a tool to restart system, System Restore, etc. with it.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista repair disc.
  You can do a system restart tool, system, etc it restore.
  There is not a disk of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  Mick Murphy - Microsoft partner

• Computer goes to a loop of reboot after Windows update

  After a complete restoration of the PC, tried to install the update to windows, my computer goes to a restart and stuck loop installation of updates stage 3 of 3 so went ahead and made a factory again restore but the windows updates causing the problem, it is stuck in a reboot loop suggestions. Is it because of damaged hard drive files?

  Perform a restart from a hard stop. Press the f8 key until you get to the screen asking questions on safe mode. Select repair. Then, you should find a system restore option. Select it. Spend until it gives you a choice of dates, then select a date before the update. This worked like a charm and does not lose any data. Turn off your automatic installation of updates option.

• A loop of reboot after upgrade

  My Windows Vista-based computer through an automatic upgrade last week.   After installing the upgrade, I was necessary to reboot the machine to complete the installation of the command.  When the computer restarts, it will show the Microsoft Logo and then arrive at a screen indicating that it finishes the installation.  After 10 seconds, it will reboot the machine and restart the process.  He only stopped when I turned off the machine.  I was able to get to a DOS command prompt and can access the hard drive, the material seems correct.  However, when I try a system recovery, it will say that it does not find a recovery before installing the upgrade.  Any suggestions on what I can do to try to short to reformat the entire hard drive or reinstalling Vista?

  Phil

  the update is not installed successfully, you receive a message, and the computer restarts when you try to install an update in windows vista and windows 7

  http://support.Microsoft.com/kb/949358

• System won't do anything after trying to reinstall the Windows operating system.

  installation of XP + esc hit by mistake

  When installing on a new drive. I tried 'agree' and F * hit several times. Nothing happened and then I hit ESC once and the computer stopped everything. I tried several times so that it can reboot but nothing.

  Help, please.

  Cliff

  When installing on a new drive. I tried 'agree' and F * hit several times. Nothing happened and then I hit ESC once and the computer stopped everything. I tried several times so that it can reboot but nothing.

  Help, please.

  Cliff

  You mean that you can not BOOT from the CD and start the installation above?

  Do and start with a Darik Boot and Nuke CD, wipe off the NEW drive (make sure that it is the only one in there and you want NOTHING on it) and after you have wiped it off, start your process (boot CD, etc.).

• RESOLVED: Loop of reboot after installing new disks in RAID of PERC S100

  A customer has a Dell T110 (with a PERC S100 RAID controller) running Windows 2008 R2. The system has two disks: a reader not RAID (C :) running the operating system and a RAID1 drive (E :) sharing data with network folders.) We need to install again, larger disks for the RAID.

  I thought I could backup the data on the RAID drive existing (e), install new disks, built a new table in the S100 (VDM) virtual disk boot manager, boot into the operating system, create the new partition for the data replaced E: drive and copy the data back. This was not the case. After installing the new disks and the new array of construction (which is reported as "READY (R/W)" when starting, Windows starts all the way in "press CTRL-ALT-DEL to log". After two or three seconds, the system reboots. The same thing happens when I try to start safe mode. The system IS NOT automatically booted to the Recovery Console. He never seems to know that an error occurred and the system was not shut down normally.

  I booted into the Recovery Console, installed the drivers for the PERC S100 and run recovery to start without success. Also in the Recovery Console, I ran 'chkdsk /f E:\. ' (remarkably, the drive letter for the data drive remained the same), and no error has been reported. I also reinstalled drivers S100 of the recovery using DISM Console, but that changed nothing.

  I started to 8.1 Windows PE, installed drivers S100, formatted the virtual disk, copied the data which he, and everything works fine. The only problem is when I try to boot from the system drive (which has no problem) with the new installed disks.

  When I put the old records, the system boots normally with no reconfiguration required. The VDM to start automatically remembers the discs and the table. Nothing shows up in the logs event indicating that there was an error during startup. (Ntbtlog.txt) start-up newspaper, after several boots with the new drives in place, indicates that the system restarts at various times during loading drivers. There is nothing coherent in the startup log to indicate what the problem is.

  The only clue I have is that, during the startup, the VDM reports the virtual drive of origin as 'NORMAL (R/W)' and the new virtual disk as "READY (R/W)", but I'm not sure of the significance of this difference or if it suggests a solution.

  I can't find clues in all the newspapers about what may be the problem. If anyone has any suggestions, I will be grateful. I'll be especially grateful for the wacky suggestions.

  I ran it. Nothing appeared unusual. However, I does not solve the problem.

  I connect the new readers to the same SATA ports as the old records. When I connect one of them to the SATA port that had not been used as part of the original painting, the VDM S100 reported the original failed array, because readers were is more connected and showed the new table as a LOAN. The operating system then started normally.

  The trick, it seems that you should remove the old virtual disk before connecting the new disks on the same ports.

• Satellite P500 - loop of reboot after using the Toshiba Recovery disk

  Hello

  I have a problem recovery SATELLITE P500. I did the recovery disks. It starts ok on the recovery disk and format the hard drive and copy the disks to the hard drive. Then, he begins installing windows and restarts.

  He then goes to a loop
  (1) marketing and says "Setup is preparing your computer for first use.
  (2) Toshiba banner saying please wait... Second installation may take several minutes. Pleae do not interrupt or shut down the computer!
  (3) Windows logo
  (4) close...
  (5) restarts and goes to 1)

  It would be great if someone could help me with this.

  Thank you very much
  Softari

  Hello

  I noticed the same thing on my Satellite P500, but I must say it s not a problem, it of quite normal. The computer will restart several times (10 times or more) to complete the installation.

  You know that a lot of drivers/tools will be installed and some restart is required to configure everything properly.

  So don t interrupt the installation of recovery, just wait a little longer and a coffee. Everything is done automatically and your laptop is reinstalled with the factory settings. :)

• Stuck on the screen saying 'Shutting Down' after trying to install SP2 on Vista

  So I got problems with my Windows Vista. The day passed or it would freeze completely, all programs not responding. I looked around, and he said that a possible solution would be to install SP2. So I did. As he installed the first of 3 updates, it got stuck at 44% for an hour. Then, she moved to say Shutting Down, which was during the last two hours.

  I don't know what to do now. During the installation, he said do not put off your computer, and while it is said that is no longer, I'm still hesitant to do. Any ideas on what I should do? In addition, would set the gel I described previously by SP2? Or do you know of anything that could be causing it?

  Thank you

  Free unlimited installation and compatibility support is available for Windows Vista SP2 questions until February 26, 2010. Availability of support chat or messaging differs depending on your location. Some questions may require that more support for which he is advanced a charge.  Go to http://support.microsoft.com/oas/default.aspx?prid=13014&gprid=582034 & select appropriate category (i.e., download problem;) Installation problem; Problems after installing a service pack). ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Endless loop of reboot after Win Update. How can I get out of it?

  I just ran Windows Update to update my Acer 3680 running Vista Basic. Downloaded 33 installed files some, then went into a reboot.  The computer keeps indicating "configuration of updates: Stage3 3-0% complete.". Do not turn off your computer. ', then turn around and restarts in the same message.

  I suspect tries to run a corrupt file, it cannot go beyond enforcement of the boot file which has been modified to run it.  F8 boot options (safe mode, etc.) just go back to the same thing.

  Hi Lmmohr,

  ·         You are trying to install updates?

  Try the procedure described in the following article:

   

  An update is not installed successfully when you try to install the update in Windows Vista and Windows 7

   

  http://support.Microsoft.com/kb/949358

  I hope this helps.

• loop of reboot after update

  Windows Server 2008 R2 - after you install an update, the server restarts, says it is to complete the update and then restarts again and forever.

  Hi Michael,

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  Hope this information helps.

• loop of reboot after upgrade to 9.3

  Hello

  I did the upgrade to 9.3 this morning and my curls by restarting since phone. I only see a black screen with a white head and a white screen with a black Apple. Even a hard reset (Home button + button for 10 seconds to STOP) has not solved the problem.

  Some may see this behavior as well?

  BR

  Florian

  If the update did not complete properly, put your phone in recovery mode and restore with iTunes.

  If you are unable to update or restore your iPhone, iPad or iPod touch - Apple supports

• Windows does not load after trying to reinstall Windows 7 Windows 10

  We did not want Windows 10 but he force installed.  It was far too slow, so we decided to go back to Windows 7.  Now our computer does not start in Windows.  He performs a repair of the system, but says it can't finish: unknown error checking: the 7th. Is not = 0 error Code x 490.  It is the second time that this happens and I can't wait to have to pay to get the fixed computer again.  I don't have the Windows 7 startup disk.  At this point, we'll go to Windows 10 - just need to get the computer working again for business.  I can install Windows 10 at this time or I will lose all my data?

  Hello Diane,.

  I would like to know some information about the problem so that we can help you better.

  What is the brand and model of your computer?

  Thank you for details on the question and your efforts to resolve.

  I also realize the inconvenience that you are experiencing due to error error checking . I will definitely help you.

  Bug SYSTEM_THREAD_EXCEPTION_NOT_HANDLED control has a value of 0x0000007E. This bug check indicates that a system thread threw an exception that the error handler did not.

  I suggest you use the steps in this article and check if it helps.
  Reference:
  (Content developer) Bug Check 0x7E: SYSTEM_THREAD_EXCEPTION_NOT_HANDLED
  https://msdn.Microsoft.com/en-us/library/Windows/hardware/ff559239 (v = vs. 85) .aspx

  Important notes:
  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• After a new reinstall of xp sp2 can not upgrade to sp3

  After a new reinstall of xp sp2 is unable to upgrade to sp3. get this message: the site has encountered a problem and cannot display the page you are trying to view

  Thanks for the info on this problem.
  I installed the patch (KB953356) and installed sp3 and the PC is up and running.

  Download the update for Windows XP (KB953356) package now.

  Thanks again.

• I tried to reinstall yosemite OX since yesterday after I wipe the drive and it froze.  It is said bark 2 hours and 7 minutes since last night.  What can I do?

  I tried to reinstall yosemite OX since yesterday after I wipe the drive and it froze.  It is said about '2 hours and 7 minutes' since last night.  What can I do?

  Try to turn off the computer with the power switch, and then restart.

• After trying to install the updates. my computer is now stuck in constant reboot mode while showing "Configuring updates 3 of 3 0%, do not turn off your computer.

  Visa update problem

  After trying to install the updates.  my computer is now stuck in constant reboot mode while showing "Configuring updates 3 of 3 0%, do not turn off your computer.  I tried to follow the instructions provided here because it seemed to be the same problem.  But when I restart and hold down the F8 key so I can boot into safe mode, I tried selecting safe mode and I get the same results, and I tried again by selecting the option 'Disable automatic reboot' which seems to be an option on the same page with the option of safe mode.  Whatever it is, the same message comes back and I can never get to where I can see my desktop to click 'start '.  I can't get out of this cycle.  I installed the update because it said I needed to install it.

  *************************************************************************************************************************************************

  Turn off your computer by holding the power button for about 20 seconds.
   
  Start your computer in safe mode: press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears
   
  Disable the automatic restart in the event of system failure:
   
  • Click Start
  • Click on Control Panel
  • Click on system and Maintenance link.
  • Click on the system link
  • In the left pane, click Advanced system settings
  • Locate the startup and recovery area, click the settings button.
  • In the startup and recovery window, uncheck the box next to automatically restart.
  • Click OK in the startup and recovery window
  • Click OK in the System Properties window
  • Close the system window
   
  After that... While STAYING in safe mode I do a system restore and maybe try a manual install of the update later.
   
  For the sake of space I refer you to the article about how to proceed.
   
  System restore
  http://windowshelp.Microsoft.com/Windows/en-us/help/9f6d755a-74bb-4A7D-A625-d762dd8e79e51033.mspx
   
  Windows updates: http://windowshelp.microsoft.com/Windows/en-US/Help/8f259118-0d61-4c7a-8c56-24987e87a8171033.mspx
   
  Please let us know if this solution works for you

  Theresa
  Microsoft Answers Support Engineer

  Hello

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/