AAA authentication sequence
We have following commands configured on the 2950
AAA new-model
AAA authentication login default local radius group
the AAA authentication enable default
RADIUS group AAA authorization exec default authenticated if
localuser username secret 5 *.
When you try to access the switch it's mark to the RADIUS server, but it is not authenticated.
And then he gets authenticated with the local user name.
Here is the log of the RADIUS server
It shows the correct user name and correct the source of the switch IP address.
Authentication provider = Windows
Authentication server =
Policy-Name =
Authentication type PAP = EAP-Type =
Code motif = 16 Reason = authentication was not successful because an unknown user or bad password name has been used. In principle it was expected that as long as the switch is able to connect to the RADIUS server, it will not use the local username for authentication. But the switch uses the local username even if he can contact the RADIUS service. Please share the experience. Thank you Subodh Hello Indeed, I've recreated the issue when authenticating against a RAQ. My switch is running a newer version, however, it always reports the error of decryption on newspapers when the shared secret is incorrect. Shared secret configured as "cisco" on the switch and as "cisco123" relating to the registration of the IAS RADIUS client. Got the following text: Priv15 of the user has been denied access. Fully-qualified-user name = CAMEJIA\priv15 NAS-IP-Address = x.x.250.12 NAS-identify = Station called = identifier Calling-Station-identifier = Client-Friendly-Name = x.x.250.12 Client-IP-Address = x.x.250.12 NAS-Port-Type = Async NAS-Port = Proxy-policy-Name = use Windows authentication for all users Authentication provider = Windows Authentication server = Policy-Name = Authentication type PAP = EAP-Type = Code motif = 16 Reason = authentication was not successful because an unknown user or bad password name has been used. On the debugging switch: * 06:02:13.600 Mar 2: RADIUS: receipt id 1645/6 x.x.250.20:1645, Access-Reject, len 20 * 06:02:13.600 Mar 2: RADIUS: 24 84 60 FA B8 43 3rd A9 authenticator - AC 55 72 70 CE 34 BA 70 * 06:02:13.600 Mar 2: RADIUS: authenticator response decrypt fault, len 20 pak * 06:02:13.600 Mar 2: RADIUS: package dump: 03060014248460FAB8433EA9AC557270CE34BA70 * 06:02:13.600 Mar 2: RADIUS: digest expected: D22363698E8862015AC91213B540D77C * 06:02:13.600 Mar 2: RADIUS: authentic response: 248460FAB8433EA9AC557270CE34BA70 * 06:02:13.600 Mar 2: RADIUS: ask authentic: 32B4A229A7EB982A61EB31E29A24AA47 * 06:02:13.600 Mar 2: RADIUS: response (6) could not decipher Please, create a new RADIUS client for the switch only and use a single key as "cisco" on both sides. Do not forget that we should not hit the space bar when you configure the key on the IOS since it will space as a valid shared key figure. I hope this helps. Kind regards. Tags: Cisco Security I have configured the banner authentication aaa and aaa fail message on a router running 12.1 (15) - authentication is done by ACS 3.0.2 which works very well. Problem - the banner of authentication does not appear (nothing is outside of "username:"-don't not even 'check' user access) If you enter a wrong password, but the failure message. If I console in and unplug the interface while the two messages very well. Workaround solution - if I set up a connection "banner" then everything works fine too, but I can't work out why does not display the "banner of aaa authentication." I suspect ACS prevents the message, but I can't work out how - can anyone suggest a solution? Thank you very much! By the way that the command "radius-server administration '? It doesn't seem to be documented, and it has no effect or not. The banner command does not work if you make the RADIUS authentication, it will not work if you do a RADIUS/local/etc. This is normal, cause with Ganymede you can have the sending server banner and guests down (even if with all I don't think that you can do) and so if you have configured authentication GANYMEDE the router does not take into account the banner command and waits to see if she gets a new one from the server RADIUS itself. If it is not it will simply display the usual guests. As for the 'radius-server admin' command, honestly, I have no idea, never seen anyone use. Online help says "start the daemon of Ganymede management administrative messages", but what really I don't know, maybe someone else can help. the AAA authentication enable default group Ganymede + activate I implement CSACS 4.0. First of all on the client, I will apply aaa authenticatio / authorization under vty. The issure if I use the followin command the AAA authentication enable default group Ganymede + activate What happens if I connect via the console? I need to enter a name of user and password? Here is my configuration AAA new-model Group authvty of connection authentication AAA GANYMEDE + local the AAA authentication enable default group Ganymede + activate authvty orders 15 AAA authorization GANYMEDE + local RADIUS-server host IP Radius-server key Ganymede IP source interface VLAN 3 AAA accounting send stop-record an authentication failure AAA accounting delay start AAA accounting exec authvty start-stop group Ganymede +. orders accounting AAA 15 authvty power group Ganymede +. AAA accounting connection authvty start-stop group Ganymede +. line vty 0 15 connection of authentication authvty authorization orders 15 authvty authvty connection accounting accounting orders 15 authvty accunting exec authvty Any suggestion will be appreciated! It should work because it is a guest message.banner whenever you try to connect (console/vty). I set it up on my router. If you have banner motd, it will appear as well (see below). So, I have to remove it to get only the aaa banner & prompt is displayed: ************************************************************ Username: cisco, password: cisco (priv 15f - local) *. ************************************************************ Any unauthorized use is prohibited. Enter your name here: User1 Now enter your password: Router #. The configuration more or less looks like this: AAA new-model AAA authentication banner ^ is forbidden to use CUnauthorized. ^ C AAA authentication password prompt "enter your password now: AAA-guest authentication username "enter your name here: Group AAA authentication login default RADIUS local authentication AAA CONSOLE connection HTH AK AAA authentication in Cisco router I want to create the user name and password with the level of prévilige for each user in the Cisco 3640 router. I don't have any authentication server, and I want to use the local database of the Cisco router to do this. Can someone suggest me how should I proceed. Thanks in advance Hello If you want to create users in the local database of the router, you must use the following command username cisco password privilege 5 test AAA new-model AAA authentic login default local AAA exec default local author Thank you Sujit The AAA authentication configuration We have ACS server 3.1 to AAA for authentication for all routers and switches. I want each person to connect the router using its own id, password password and activate. If the ACS server is unavailable, I want to have different id, password and enable password for console and telnet access. What is the right way to do this? I also want to follow all orders entered on the router. That's what I have: AAA new-model AAA authentication login default group Ganymede + local enable AAA authentication login no_tacacs the AAA authentication enable default group Ganymede + line AAA authorization exec default group Ganymede + local AAA authorization commands 15 default group Ganymede + local AAA accounting exec default start-stop Ganymede group. orders accounting AAA 15 by default start-stop Ganymede group. ! username admin password 7 xxxxxxxxxxxxxxxx ! ! Line con 0 connection of authentication no_tacacs line to 0 line vty 0 4 password 7 xxxxxxxxxxxxxxxxxxxxxxxx ! Yes, it's Joy on the right. Thank you, Renault http using aaa authentication when Ganymede server is down I installed AAA using Ganymede and everything works well except for authentication http through a browser or a network Assistant when the RADIUS server is down. For console and telnet connections, the default authentication line when Ganymede is out of service. AAA new-model AAA authentication login default group Ganymede + line AAA authorization exec default group Ganymede + authenticated if AAA accounting update newinfo AAA accounting exec default start-stop Ganymede group. only AAA 0 default stop accounting controls group Ganymede +. only AAA 1 default stop accounting controls group Ganymede +. accounting AAA commands default 15 stop only Ganymede group. ! aaa IP http authentication ! radius-server host 10.161.161.20 111111 radius-server key It must be something with the fact that on http or ANC, it connects to the router at level 15, but I have played with all sorts of orders of different authorization and cannot operate. Paul What you want to do for authentication if the RADIUS server is down? For telnet and console access you can use the line as a backup method because it is possible to configure a password for the line on the console and vty ports. Which type of backup method you want for HTTP? The one that seems most logical to me would be to a local authentication in order to cover the situation where the server is down. To use local authentication, you must do the following: -create a definition of the local user (maybe more if you need extended security). -specify a special method for authentication of the aaa. -specify that http, using the special method. The configuration might look like this: password user tech1 tech1 AAA authentication login http_auth group Ganymede + local IP http authentication aaa - authentication of the connection http_auth Or you can decide to use the secret to activate (or password that is configured in office). The config might look like this: AAA authentication login http_auth group Ganymede + activate IP http authentication aaa - authentication of the connection http_auth If you want a different backup method, let us know what it is and we'll see how it could be implemented. HTH Rick No AAA authentication for switch I'm intrigued by my question. I have a switch on 9 that cannot authenticate with our server GANYMEDE. The configurations are the same as any other switch, but when I try to open a session using the account GANYMEDE + access is denied. This is the configuration for the AAA/GANYMEDE on the switch. AAA new-model AAA authentication login default group Ganymede + local radius-server X.X.33.XX host I deleted the aaa configuration and then reconfigured it as well as the information from the server RADIUS and no authentication Ganymede. I gave the Ganymede interface should use, but same result. Any ideas? Thank you Robert Robert, Please make sure following -Radius server is accessible from the switch and port 49 is not blocked. S ' it is layer 3 switch, then make sure to configure the interface source ip Ganymede XXXX (Interface IP set in radius server) -Check the secret key If the problem is still there then please get Debug aaa authentication debugging Ganymede Kind regards ~ JG AAA authentication and privilege-mode I want to configure authentication aaa with accounts of local user on the switch. The idea is to come directly into the "privilege" without the enable command mode. I have configured the following commands: AAA new-model AAA authentication login default local What other commands (permission) are necessary to obtain the command of privilege? Thank you Pascal Dear Sir For the console you must issue to order more. There is a hidden within IOS command you will need to apply: "authorization aaa console. Who should fix it Kind regards ~ JG Note the useful messages Excluding the lines of Terminal Server in the AAA authentication Hi all Hope you can help, I'm trying to find a solution to exclude only the following line port by using the AAA authentication (ACS GANYMEDE +) on a map of Terminal Server on a Cisco 2600 router. Does anyone know how to do this, or point me in the right direction to solve? I've included the output below: AAA authentication login default group Ganymede + local line 41 Is it a question of disabling the command line or using a defined group? Thanks a lot for your help. Jim. Hi Jim You may need to create another group for authentication to the and send your AAA configuration line to 0 connection of authentication aux_auth AAA authentication login aux_auth line You can also configure a username local/pw and map it on the group to here... Console and telnet would still use the configured default group, or you can specify specific groups: Line con 0 console login authentication line 4 vty0 vty authentication login and specify the aaa authentication settings individually... I hope this helps... all the best REDA Here is the config, I have a switch: AAA authentication login default group Ganymede + local AAA authentication login vtylogin group Ganymede + local AAA authentication login conlogin group Ganymede + activate none the AAA authentication enable default Ganymede + activate Now, here are my questions: 1. when I have my login of Ganymede console connection works, but when I type 'enable' and try to use my password to Active Directory, it does not work. So I try the enable password, don't worry. However if I change the 4th line "aaa authentication enable the Activate by default", I can now by using the enable password. 2. my second question is when I SSH into the switch, I want only that it uses the RADIUS server and use only the database local when the Ganymede is not available. However while Ganymede is available, I am still able to login using the local user account. I guess that's by design? Is there a way to prevent this if it isn't design? When you use the local user account to connect to the device, can you check if you can see the log in "past the authentication attempt" on the box of the CSA? If so, the same account could you please check your local ACS DB user to see that it was created by a fake? The AAA authentication and VRF-Lite Hello! I encountered a strange problem, when you use authentication Radius AAA and VRF-Lite. The setting is as follows. A/31 linknet is configured between PE and THIS (7206/g1 and C1812), where the EP sub-si is part of a MPLS VPN and VRF-Lite CE uses to maintain separate local services (where more than one VPN is used..). Access to the this, via telnet, console etc, will be authenticated by our RADIUS servers, based on the following configuration: --> Config start<> AAA new-model ! ! Group AA radius RADIUS-auth server Server x.x.4.23 auth-port 1645 acct-port 1646 Server x.x.7.139 auth-port 1645 acct-port 1646 ! AAA authentication login default group auth radius local enable AAA, enable authentication by default group RADIUS-auth ... touch of 1646-Server RADIUS host x.x.4.23 auth-port 1645 acct-port
touch of 1646-Server RADIUS host x.x.7.139 auth-port 1645 acct-port
... source-interface
---> Config ends<> The VRF-Lite instance is configured like this: ---> Config start<> VRF IP-10 RD 65001:10 ---> Config ends<> Now - if I remove the configuration VRF-Lite and use global routing on the CE (which is OK for a simple vpn installation), AAA/RADIUS authentication works very well. "" When I activate transfer ip vrf "10" on the interface of the outside and inside, AAA/RADIUS service is unable to reach the two defined servers. I compared the routing table when using VRF-Lite and global routing, and they are identical. All roads are correctly imported via BGP, and the service as a whole operates without problem, in other words, the AAA/RADIUS part is the only service does not. It may be necessary to include a vrf-transfer command in the config of Group server as follows: AAA radius RADIUS-auth server group Server-private x.x.x.x auth-port 1645 acct-port 1646 key ww IP vrf forwarding 10 See the document below for more details: http://www.Cisco.com/en/us/partner/docs/iOS/12_4/secure/configuration/guide/hvrfaaa.html AAA authentication problemssss Hello When I use commands below aaa and attempt to authenticate, I am able to authenticate with GANYMEDE +, but further then when I do "sh run" I get message "command failed authorization." Please notify. Test-Switch #sh run Authorization of command failed. AAA new-model AAA authorization exec default group Ganymede + authenticated if AAA accounting exec default start-stop Ganymede group. the String key of the host IP radius-server line vty 0 4 BUT as soon I just changed the aaa as configuration below I'm able to run sh run commands as usual without any error. AAA new-model AAA authentication login default group Ganymede + local AAA authentication login no_tacacs local activate the default AAA authentication no AAA authentication login default group Ganymede + line AAA authentication login no_tacacs line authorization AAA console AAA authorization exec default group Ganymede + local authenticated by FIS AAA authorization exec default group Ganymede + authenticated if AAA authorization exec local no_tacacs authenticated by FIS AAA authorization commands 0 no_tacacs no AAA authorization commands 1 no_tacacs no AAA authorization commands 15 no_tacacs no AAA accounting exec default start-stop Ganymede group. orders accounting AAA 15 by default start-stop Ganymede group. orders accounting AAA 0 arrhythmic default group Ganymede +. AAA - the id of the joint session Please advise, thank you. its urgent To approach the issue from a slightly different angle - your original set of commands instruct the router to send the application for leave to GANYMEDE for each command to level 15, which includes see the race. Your GANYMEDE server was not configured to allow your use to see the race and if your attempt to show performance was rejected. Your revised set of orders doesn't send application to GANYMEDE for level 15 commands (or other classes of orders by the way) and so there is no question here to see the race. As far as I can say that your revised set of orders do not permit for orders. You can achieve this result just as easily (and with fewer complications in your configuration) If you delete just aaa authorization command from your config lines. HTH Rick The AAA authentication not working method and 'by default' list Guys, I hope someone can help me here to the problem of the AAA. I copied the configuration and debugging below. The router keeps using username/password local name even if the ACS servers are accessible and functional. To debug, it seems he keeps using the method list 'default' ignoring GANYMEDE config. Any help will be appreciated Config ********************************** AAA new-model ! username admin privilege 15 secret 5 xxxxxxxxxx. ! AAA authentication login default group Ganymede + local the AAA authentication enable default group Ganymede + activate authorization AAA console AAA authorization exec default group Ganymede + local AAA authorization commands 15 default group Ganymede + local AAA authorization default reverse-access group Ganymede + local orders accounting AAA 0 arrhythmic default group Ganymede +. orders accounting AAA 15 by default start-stop Ganymede group. Default connection accounting AAA power Ganymede group. ! AAA - the id of the joint session ! RADIUS-server host x.x.x.x RADIUS-server host x.x.x.x RADIUS-server host x.x.x.x RADIUS-server host x.x.x.x RADIUS-server application made RADIUS-server key 7 0006140E54xxxxxxxxxx ! Ganymede IP interface-source Vlan200 *************************** Debugs 002344: 5 Dec 01:36:03.087 ICT: AAA/BIND (00000022): link i / f 002345: Dec 5 01:36:03.087 ICT: AAA/AUTHENTIC/LOGIN (00000022): choose method list "by default". 002346: Dec 5 01:36:11.080 ICT: AAA/AUTHENTIC/LOGIN (00000022): choose method list "by default". core01 #. 002347: Dec 5 01:36:59.404 ICT: AAA: analyze name = tty0 BID type =-1 ATS = - 1 002348: Dec 5 01:36:59.404 ICT: AAA: name = tty0 flags = 0 x 11 type = 4 shelf = 0 = 0 = 0 = 0 = 0 channel port adapter slot 002349: Dec 5 01:36:59.404 ICT: AAA/MEMORY: create_user (0 x 6526934) user = "admin" ruser = "core01" ds0 = 0 port = "tty0" rem_addr = "async" authen_type = service ASCII = NONE priv = 15 initial_task_id = '0', vrf = (id = 0) 002350: Dec 5 01:36:59.404 ICT: tty0 AAA/AUTHOR/CMD (2162495688): Port = "tty0" list = "service = CMD 002351: Dec 5 01:36:59.404 ICT: AAA/AUTHOR/CMD: tty0 (2162495688) user = "admin". 002352: Dec 5 01:36:59.404 ICT: tty0 AAA/AUTHOR/CMD (2162495688): send service AV = shell 002353: Dec 5 01:36:59.404 ICT: tty0 AAA/AUTHOR/CMD (2162495688): send cmd = AV set up 002354: Dec 5 01:36:59.404 ICT: tty0 AAA/AUTHOR/CMD (2162495688): send AV terminal = cmd - arg 002355: Dec 5 01:36:59.404 ICT: tty0 AAA/AUTHOR/CMD (2162495688): send cmd - arg = AV
002356: Dec 5 01:36:59.404 ICT: tty0 AAA/AUTHOR/CMD (2162495688): found the 'default' list 002357: Dec 5 01:36:59.404 ICT: tty0 AAA/AUTHOR/CMD (2162495688): method = Ganymede + (Ganymede +) 002358: Dec 5 01:36:59.404 ICT: AAA/AUTHOR/TAC +: (2162495688): user = admin 002359: Dec 5 01:36:59.404 ICT: AAA/AUTHOR/TAC +: (2162495688): send service AV = shell 002360: Dec 5 01:36:59.404 ICT: AAA/AUTHOR/TAC +: (2162495688): send cmd = AV set up 002361: Dec 5 01:36:59.404 ICT: AAA/AUTHOR/TAC +: (2162495688): send AV terminal = cmd - arg 002362: Dec 5 01:36:59.404 ICT: AAA/AUTHOR/TAC +: (2162495688): send cmd - arg = AV
Enter configuration commands, one per line. End with CNTL/Z. core01 (config) #. 002363: Dec 5 01:37:04.261 ICT: AAA/AUTHOR (2162495688): permission post = ERROR 002364: Dec 5 01:37:04.261 ICT: tty0 AAA/AUTHOR/CMD (2162495688): method = LOCAL 002365: Dec 5 01:37:04.261 ICT: AAA/AUTHOR (2162495688): position of authorization = PASS_ADD 002366: Dec 5 01:37:04.261 ICT: AAA/MEMORY: free_user (0 x 6526934) user = "admin" ruser = "core01" port = "tty0" rem_addr = "async" authen_type = ASCII service = NONE priv = 15 core01 (config) #. Ganymede + accessible servers use source vlan 200. Also in the Ganymede server + can you check if the IP address for this device is configured correctly and also please check the pwd on the server and the game of this device.
As rick suggested sh Ganymede would be good as well. That would show the failures and the successes HTH Kishore GANYMEDE + Queueing AAA authentication Hello I've recently updated the IOS on my 3560 X 15.0 (2) SE3 and I can't get GANYMEDE works correctly. It worked properly on this device until I updated the IOS so I don't know what happened. I've made a few other changes as well (management IP change and clean the other config) so I'm not 100% sure what the issue was with the IOS. I have this same exact config on several other Cisco devices and it works fine. Any thoughts are appreciated. Config: AAA authentication login default group Ganymede + local AAA authorization exec default group Ganymede + local Ganymede IP source interface Vlan1 radius-server host Ganymede IP source interface Vlan1 Debugs: MORE: Queuing request authentication AAA 88 for the treatment I never spent queuing. I can't find a way to clear the queue either. I have to disable the uplink port and reboot the switch to not even enter the port of the console. At this point, I get 1 authentication attempt (debugging below) before entering the queue messages. 21:34:36.864 Mar 29 CDT: % LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed State to 21:40:48.068 Mar 29 CDT: MORE: Queuing AAA request authentication 47 for the treatment 21:40:48.068 Mar 29 CDT: HIGHER: processing id authentication of demand beginning 47 21:40:48.068 Mar 29 CDT: MORE: authentication start package created for 47(**USERNAME**) 21:40:48.068 Mar 29 CDT: MORE: using the 10.x.x.x server 21:40:48.068 Mar 29 CDT: HIGHER (0000002F) / 0/IDLE/68F4CBC: started 5 sec timeout 21:40:48.077 Mar 29 CDT: HIGHER (0000002F) / 0/IDLE/68F4CBC: got immediately connect on the new 0 21:40:48.077 Mar 29 CDT: HIGHER (0000002F) / 68F4CBC/WRITING/0: started 5 sec timeout 21:40:48.077 Mar 29 CDT: T +: 192 (0xC0) Version, type 1, seq 1, encryption 1, SC 0 21:40:48.077 Mar 29 CDT: T +: session_id 912650955 (0x3665F2CB), dlen 32 (0x20) 21:40:48.077 Mar 29 CDT: T +: type: AUTHENTIC / START, priv_lvl:1 action: ascii LOGIN 21:40:48.077 Mar 29 CDT: T +: svc:LOGIN user_len:11 port_len:4 (0x4) raddr_len:9 (0 x 9) data_len:0 21:40:48.077 Mar 29 CDT: T +: user: (* USERNAME *) 21:40:48.077 Mar 29 CDT: T +: port: tty1 21:40:48.077 Mar 29 CDT: T +: rem_addr: 10.y.y.y 21:40:48.077 Mar 29 CDT: T +: data: 21:40:48.077 Mar 29 CDT: T +: end of packet 21:40:48.077 Mar 29 CDT: HIGHER (0000002F) / 0/WRITING: write to 10.x.x.x failed with errno 257 ((ENOTCONN)) 21:40:48.077 Mar 29 CDT: MORE: authentication start package created for 47(**USERNAME**) 21:40:48.077 Mar 29 CDT: HIGHER (0000002F): start write failed 21:43:01.976 Mar 29 CDT: % SYS-5-CONFIG_I: configured from console by dcmorris on console 21:43:08.057 Mar 29 CDT: MORE: Queuing AAA request authentication 48 for the treatment 21:45:24.842 Mar 29 CDT: MORE: Queuing AAA request authentication 49 for the treatment 21:48:52.494 Mar 29 CDT: MORE: Queuing AAA asks 50 for processing authentication You might want to take a look here https://supportforums.Cisco.com/message/3965551#3965551 Jatin kone -Does the rate of useful messages- Activate the ASA system context AAA authentication Hello! We have ASA configured in multiplayer in context with 8.4 (2) software configured for AAA Configuration is admin context as follows: AAA-server TAC Protocol Ganymede +. host of the TAC AAA-server 10.162.2.201 (management) key *. Console to enable AAA authentication LOCAL TAC TAC LOCAL console for AAA of http authentication AAA authentication serial console LOCAL TAC authentication AAA ssh console LOCAL TAC Because of the multiple context, after the connection we enter in the system context. Console port authentication works very well except access to the privileged mode when you connect through the console port. After the show 'enable' command ASA accepts only configured activate secret in context and change ID of user system for enable_15, so we are unable to do accounting and authorization of user level control. It seems that the ASA in the context of the system is not aware of all the configurations of AAA, and it is not a command to configure AAA in the context of the system. Is there a way to configure enable AAA authentication in the context of the system? Thanks in advance! Hello It looks like you hit this known issue that follows: Symptom: In multi-mode configuration, the user to enter privileged mode credentials Conditions: ASA/PIX is in multi mode. serial console and activate the console authentication Workaround solution: Option 1: Configure enable password in the system context. Option 2: Avoid the use of the interface of the console series and rely on telnet When authentication is enabled for the serial console and activate console in Hope that clarifies it. Unfortunately there is no solution for this problem. Kind regards. Several entries of stream serial I try to display the results of two RS-232 different instruments that operate asynchronously with no handshake. Each counter (a scale of weight one and the other a DVM) update at different speeds. I want to enjoy them every 100mS and show the value PXI-6704, parallel to the measurement of the resistance Hello I'm in show two separate circuit analysis procedures. First of all I would like to provide two pins with current and measure the response of circuit elsewhere, and second, I want to test the total resistance not fueled between those two pins. I How can I stop my computer to open windows in safe mode? I just intalled norton security as I had no security for a while, since this window opens in safe mode but it seems oninstallation of security scanning all the risks have been removed how to get back to normal windows mode How to change the sound scheme I work with windows vista, and I want to change my sound scheme to something other than what is on the menu drop down. How can I get different sounds? Looking for AIO 3240Similar Questions
authorization AAA console
AAA authorization exec default group Ganymede + local
radius-server key 7?
AAA authorization exec default group Ganymede + local
AAA accounting exec default start-stop Ganymede group.
AAA accounting network default start-stop Ganymede group.
AAA accounting default connection group power Ganymede
AAA accounting system default start-stop Ganymede group.
AAA - the id of the joint session
session-timeout 20
decoder location - XXXXXX XXXXXX BT
No banner motd
No exec-banner
absolute-timeout 240
Modem InOut
No exec
transport of entry all
StopBits 1
Speed 38400
AAA authentication login NETWORK_ACCESS group Ganymede + local activate
the AAA authentication enable default group Ganymede + activate
default 15 AAA authorization commands group Ganymede + none
orders accounting AAA 15 by default start-stop Ganymede group.
transport input telnet ssh
authentication of the connection NETWORK_ACCESS
exec-timeout 10
GANYMEDE-server host 10.x.x.x key *.
Admin context allow mode compared to the context system DB credentials
(enable mode) via the serial console is not sent to an external server
role of authentication.
are configured to use external aaa server in the context of the admin.
or ssh console access. SSH or telnet consoles, tries to enter
active mode is authenticated as specified by the configuration of aaa in
the context of "admin".
Other Description of the problem:
Executive admin via an external aaa Server (for example: radius or Ganymede +), series
Console OmniPass is against the external aaa server, but the mode
credentials are compared with enable db in the context of the system.Maybe you are looking for