AAA for PIX 7.2 (2)

Similar Questions

• Backup AAA for PIX

  I have a PIX with the following configuration:

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + (inside) host 192.168.1.1 77777 timeout 5

  RADIUS Protocol RADIUS AAA server

  AAA-RADIUS (inside) host 192.168.1.1 Server 77777 timeout 10

  AAA-server local LOCAL Protocol

  AAA authentication GANYMEDE serial console +.

  AAA authentication enable console GANYMEDE +.

  order of AAA for authorization GANYMEDE +.

  AAA accounting correspond to aaa_acl inside RADIUS

  Everything works fine when the RADIUS server is available. When he is not available, I can log in with the username "PIX" and "password". The problem is, once I connected, I can't get permission to execute orders. Does anyone know of a command that is similar to the "if-certified" for routers that I can use?

  There is no method of backup for authorization for the PIX. As you know, if the RADIUS server is down, you can connect with "pix" and the password enable, but it doesn't help a permission. The only thing you can do is wait the GANYMEDE server back to the top. I'm sorry.

• Where Smartphones blackBerry is my memory last? Ugh! No memory for pix!

  Hello

  I tried to take a few pictures with my storm last night when I was at a party and when I tried to do, I got an error message.

  I can't show you a picture, you cannot add attachments, but the error message reads:

  (letter i icon) File system error

  (the folder icon) / Device memory/home/user/photos

  Name: IMG0007-200... (name of the photo)

  I looked everywhere that I have air...

  I went to the Options... Memory and looked at what I had available. Here's what I found:

  Application memory

  Free space: 9.6 MB

  The device memory

  Total area: 879.2 MB

  Free space: 0.0 KB

  Multimedia card

  Total space: 7.3 GB

  Free space: 5.6 GB

  Of course, the glaring problem is that I don't have ANY free space on the device.  Where everything is?  I have a 8 GB memory card and I have uploaded about 150 songs in my Storm. However, I have not downloaded photos or anything else. What happened to all the memory?   Where everything is?

  I tried a couple things like turn market, pulling out the memory card, etc... I tried to attach the storm and then sneaked in the records themselves and the only things I could find in ALL files was my MP3 files.

  Anyone know what's happened here?

  Thank you!

  Rob

  I just thought the "battery pull" solution, but how do I make my memory card a 'default' location for pix?

  Thank you!

  I will go ahead and try this battery pull and tell you how it goes...

• What version of PDM for PIX 6.3 (4) on a 515E?

  I loaded the last PDM bin 4.1 (1) for PIX os ver 6.3 (4) but I get an error message when I try to access the new PDM:

  "Cisco PDM 4.0 for FWSM does not work on PIX. Please install Cisco PDM 3.0 on your PIX"

  Hmmm a Pix Device Manager which does not work on PIX? The links were wrong on the cisco.com page that pointed me to this location?

  http://www.Cisco.com/cgi-bin/tablebuild.pl/PIX

  Are these compatible versions?

  Here's my version:

  Cisco PIX Firewall Version 6.3 (4)

  Cisco PIX Device Manager Version 4.1 (1)

  Yes, this message is absolutely right, version 4.x PDM is just for the firewall Switch Module and is not supported by the device of PIX. FWSM supports Transparent firewall features that the PIX does not now support.

  Version 3.0.2 PDM.

  There will be a new PDM with the PIX OS 7.0 version in the first quarter of 2005.

  sincerely

  Patrick

• Q for PIX-525 spec (failover FE) and the GBIC

  Qestion for PIX-525 spec.

  1 PIX-525-UR-GE-BUN(2GE + 2FE). I want to use 2GE as inside and outside interface and failover FE. I found a doc who must use the GE model 535 failover. Is it supports statefull failover FE model 525?

  2 PIX-1GE-66 map PIX 525, is the built in card GBIC interface, or do I module GBIC order (ex, WS-G5484) to put into the card?

  Thank you

  1. the restriction on the use of a dynamic rollover interface that corresponds to the fastest interface on the PIX is the PIX 535. The PIX 525 cannot switch the line traffic GE rate if this restriction is lifted on the 525 platform. You can use a link FE on a PIX 525 as the dynamic link even if you have GE links as other interfaces.

  2. the GE on the PIX interface card contains a multimode SC connector. No GBIC not necessary... just of cables.

  I hope this helps.

  Scott

• can I use aaa for telnet access to a pix?

  It's a 6.2 (2) the 506e running. I have all my routers and switches use Ganymede authentication. is it possible on with the pix? useful links or instructions?

  Thank you

  YES, you can control access to pix via Ganymede or any aaa server. Here is the link perfact explaining config etc for

  http://www.Cisco.com/warp/customer/110/authtopix.shtml

• The AAA for PIX515E 6.3 rules (5)

  Hello. If I wanted to configure the PIX for the authentication of an ACS server (for the purpose of management of PIX), what else would need apart from what follows:

  AAA-server Admin-FW Protocol Ganymede +.

  AAA-Server Admin-FW max-failed-attempts 3

  AAA-Server Admin-FW deadtime 10

  !

  AAA-Server Admin-FW (inside) host 192.168.2.9 access timeout 10

  !

  console series FW-Admin-AAA authentication

  Console telnet authentication AAA Admin-FW

  authentication AAA ssh console Admin-FW

  As far as I KNOW, I did not specify which IP addresses can someone telnet from to connect on the PIX. I tried the following, but I do not know I did not provide the correct instructions:

  the AAA authentication include telnet inside 192.168.0.0 255.255.0.0 Admin-FW

  ... and I have a username / password to invite him on the PIX but it keeps asking for a user name and password. I know my account GANYMEDE is good because I can connect on the routers with the same details as what I use to authenticate on the PIX.

  I also ran a debugging on the PIX when I was trying to authenticate. The output is attached.

  Thank you

  Timothy

  Hi Tim,.

  There is no need to order,

  the AAA authentication include telnet inside 192.168.0.0 255.255.0.0 Admin-FW

  Try it now and see if you get hits on ACS. Incase it is not working, pls get again him debugs.

  Thank you

  Jagdeep

• Remove the aaa in pix server configuration

  I have pix 515 with version 6.x cisco and me configured RADIUS vpn connection client authenitcation. The radius server is windows 2003 and I have the following commands

  RADIUS protocol AAA-server test

  AAA-server test (inside) host x.x.x.x1 password timeout 10.

  The vpn works great, now I want to change the radius server and I want to delete the order and add new, but I get errors of

  When I give

  clear the aaa-server test, Iget an error message

  You must remove all corresponding entries before AAA

  removing the last server in the test group

  When I give

  No server aaa test (inside) host x.x.x.x1 password timeout 10. I get

  You must remove all corresponding entries before AAA

  removing the last server in the test group

  When I give

  no RADIUS protocol aaa-server test I get

  AAA servers configured! Cannot delete server_tag.

  I'm in a loop. Can some one adivce me how to remove the aaa tag test the firewall server

  Thanks in advance

  you are probably still referencing it in the vpn setting somewhere.

  for example

  card crypto mymap TEST client authentication

  You must remove this first

• cmd key does not not for pix not adjacent selection

  Cmd key doesn't work is not for the nonadjacent selection of pix. Worked in iPhoto, but not since the 1.0.1 Photos.

  It works in other ways as being one by design or just a default keyboard?

• LDAP AAA for VPN configuration

  Preface: I'm all new to Cisco Configuration and learn as I go.

  I'm at the stage of configuration LDAP to configure a VPN on ASA 5520, software release 8.3 (1).  Previously the programme installation and RADIUS authentication successfully tested, I tried to use similar logic to implement the LDAP authentication/authorization.  I have acquired a service account that queries the pub for the identification of the registered user information.  My main resource was the following Manual: Cisco ASA 5500 Series Configuration Guide using the CLI Software Version 8.3.  I did initially configurations by using ASDM, but could not get tests to succeed.  So I amazed the ASDM configs and went to the CLI.  Here is the configuration.

  AAA-server AAA_LDAP protocol ldap
  AAA-server host 10,20,30,40 (inside) AAA_LDAP
  Server-port 636
  LDAP-base-dn domain.ad
  LDAP-scope subtree
  LDAP-naming-attribute uid
  LDAP-login-password 8 *.
  LDAP-connection-dn cn = commonname, OU = ou01, or = ou02, dc = domain, dc = ad
  enable LDAP over ssl
  microsoft server type
  LDAP-attribute-map LDAP_ATTRIB

  ---

  type tunnel-group ASA_DEFAULT remote access
  attributes global-tunnel-group ASA_DEFAULT
  authorization-server-group AAA_LDAP

  ---

  LDAP attribute-map LDAP_ATTRIB
  name of the MemberOf IETF Radius-class card
  map-value MemberOf "VPN users' asa_default

  ---

  I tested all the naming-attribute ldap alternatives listed with the same results.

  When I test the authentication using this configuration, I get the following error: ERROR: authentication server does not: AAA Server has been deleted

  When I test authorization using this Setup, I get the same error (except for the word permission instead of authentication).

  I am at a total loss.  Any help would be appreciated.

  I would use ldp.exe to see if you can make sure that the sytnax of your ldap-connection-dn is just as you have in your config, it really helps just copy and paste.

  The problem I see is the following:

  [210] link as st_domadm
  [210] authentication Simple running to st_domadm to 10.20.30.30
  [210] simple authentication for st_domadm returned credenti invalid code (49) als
  [210] impossible to link the administrator returned code-(1) can't contact LDAP er

  I suppose your ldap-connection-dn is st_domadm and you try to test with the administrator account?

  Thank you

  Tarik

• ACS 5.4 ASA 8.2.5 disable AAA for the particular user

  Hello!

  I want to disable journaling Ganymede + for the particular user. This user is used only for automated (python script) pooling of vpn tunnel ASA (limited command set - permission on ACS) group to verify the number of users authenticated via VPN. The problem is that this user generate a bunch of logs according to authentication authorization and accounting on ACS. Is there a solution, disable Ganymede + newspapers on ACS for this particular user? Maybe it is possible to modify the AAA on ASA to not connect this particular user?

  Thanks in advance.

  Hi Pawel,

  You can create filters collection for that specific user. When you configure monitoring filters & Report Viewer does not record these events in the database.

  Navigate to: Configuration of the analysis > System Configuration > filters Collection > add a filter

  What follows is the attributes that can be used. You must use the user.

  -Access service

  -User

  -Mac-add

  -Nas - IP

  Example: We get several hits of ASA by 'user' and we want ACS to ignore it. Create a filter by using the user. ACS must now ignore any attempt from the IP Address of the NAS.

  Jatin kone
  -Does the rate of useful messages-

• allowing permission aaa on pix / asa

  I managed to get authentication on easy enough but now finds it difficult to get permission to work properly. I auth/author enabled for my IOS stuff so any connected Tech will have rights based on what I give them about secure ACS. However, I can't the same thing to work on the code of PIX. I can connect fine with sign aa, but still, he invites me to the enable password. End result is that I want to be able to connect only once (and active). The white papers that can tell me the right way?

  Hello

  What you want to do, it is possible, try following the instructions in the attached PDF file.

  And you want to give access ASDM, then make sure that you leave Assistance user privilege to execute all display orders, i.e. show-(check) permit unmatched arguments.

  Let me know.

  Kind regards

  Prem

• Select orders accounting aaa for all levels of privilege?

  Here is the syntax of the command:

  AAA accounting {auth-proxy | system | network | exec | login | orders level} {default | name-list} {arrhythmic | stop only | none} group [broadcast] name of

  The accounting type 'command' must include the privilege level of the orders that you log on. How can I connect all orders?

  Consider the following example:

   aaa accounting commands 15 default start-stop group mygroup

  If I run this command will mean that command that the user runs which have a level of less than 15 privilege are not registered? Or only commands that require exactly the privilege level 15 will be connected?

  How can I connect all orders regardless of the privilege level?

  Hey red,

  If you customize the command privilege level by using the command of privilege, you can limit who commands the unit accounts for by specifying a minimum privilege level. The security apparatus does not account for orders that are below the minimum privilege level.

  The default privilege level is 0. So if you do not specify a level of privilege then all should be counted.

  You can find the details of the order to. It's good for the SAA.

  http://www.Cisco.com/c/en/us/TD/docs/security/ASA/asa80/command/referenc...

  Kind regards

  Kanwal

  Note: Please check if they are useful.

• NPS Windows Help for authentication of aaa for Cisco router - is it safe?

  I am very confused about how all this works and was hoping someone could help me.

  I followed a bunch of tutorials online for authentication RADIUS of installation on a Cisco router and he did to a NPS Windows Server. Now I can ssh into the router my AD account.

  Now that I got it to work, I go to the settings to make sure everything is secure.

  On my router, the config is pretty simple:

  aaa new-modelaaa group server radius WINDOWS_NPSserver-private 123.123.123.123 auth-port 1812 acct-port 1813 key mykeyaaa authentication login default local group WINDOWS_NPS
  
  ip domain-name MyDomcrypto key generate rsa
  
  (under vty and console)# login authentication default
  On the NPS Windows:
  I created a new RADIUS client for the router.
  Created a secret shared and specified Cisco as the name of the seller.
  Created a new strategy of network with my desired conditions.
  And now the frame of the configuration of the network policy that worries me:
  
  
  So initially I thought my AD credentials were being sent over the wire in plain text, but I did a capture and saw this:
  
  
  
  capture.jpg
  
          
      
  
  
  How is my password being encrypted and how strong is the encryption?
  
  Another thing is how can I configure aaa authentication with mschapv2? The documentation I saw for mschapv2 uses the "ppp authentication ms-chap-v2" command, but I'm not using ppp I'm using aaa with a radius server.
   
  			 
  Hello
  RADIUS encrypts the password, but sends the username in clear. GANYMEDE encrypts the user name and password.
  You can find the encryption used by RADIUS in the RFC scheme:
  https://Tools.ietf.org/html/rfc2865#page-27
  MS-Chap-V2 is used for the authentication of users such as the remote access and vpn, not management switch
  Thank you
  John
  		   

• Permission from AAA on PIX

  I've implemented authentication and authorization on the PIX. Authentication works, but omits the authorization. I'm trying to debug nothing appears (on PIX or ACS), but it does if debug authentication

  Make sure you have enable authentication,.

  authentication AAA ssh console LOCAL GANYMEDE

  Console Telnet AAA authentication RADIUS LOCAL

  Console to enable AAA authentication RADIUS LOCAL

  GANYMEDE LOCAL AAA authorization command

  Incase it does not work pls get aaa config

  Kind regards

  ~ JG

  Note the useful messages