Acer Aspire on reformatting receives an error "not customize Windows re to recovery utility.

Similar Questions

• I can't stream the video of my Acer Aspire 5742 on my Sony Bravia KDL-55NX720 Windows 7

  I can't stream the video of my Acer Aspire 5742 to my Sony Bravia KDL-55NX720, Windows 7

  Hello

  1. what happens when you try Acer laptop to Sony Bravia TV videos?

  2. do you receive any error messages?

  3. it worked before? If Yes, did you changes to the computer before the show?

  4. you use a wired connection or wireless to connect TV and laptop?

  I suggest you provide more information about the issue so that we can better help you.

• I installed Windows 7 64 bit on my Acer Aspire one D255, but I can not install the vga intel now more.

  could someone help me please?

  Hello
  1. what happens when you try to install the VGA?
  2. you receive an error message?
  3 - is an installation problem only intel VGA or also with other applications?
  Follow the suggestions and then check out.

  Method 1

  Download from the link below and check if it works very well.

  http://www.Acer.co.UK/AC/en/GB/content/drivers

  Method 2

  Check to see if the problem exists in a clean boot state.
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: After a troubleshooting follow step 7: reset the computer to start as usual

• Acer Aspire 5750 G hard Driver Error 0x00000e9

  Hell everyone! There are a few days accidentally I drop my laptop and after that he start to becomes extremely slow... I tried everything, but a few hours later, I had no access to the window and the message 0x00000e9, again and again! I open bios just to have a look and HARD drive disappeared...

  I contact Acer and told them my problem... After that, I asked what HDD should I expect because I'm not interest in obtaining the same like the old!
  I would like to buy a better one (more RPM. Capacity and Sata 3 ofc) but they told me that I should buy the same thing! :-/

  Can someone tell me what I need to do? For sure the former were not :-(

  My laptop is Acer Aspire 5750 G i7 and the hard driver was Toshiba MK7559GSXP 750 G Sata 2 and Code KH.75004.001

  I would like to know if mobo can support Sata 3
  If I buy a new HARD drive different from what Acer suggest me to or it will be a bad deal for me and my laptop cannot support the new hardware?

  You may have dropped the HARD drive or memory loose when you dropped it. I open the doors on the bottom and check them. I hope it will be as simple as that.

• ACER ASPIRE 5610 EQUIPPED WITH BATHROOM OR NOT?

  Hello!!!     I HAVE LAPTOP ACER ASPIRE 5610 BLUETOOTH NOT APPEAR IN THE DEVICE! IT IS EQUIPPED WITH A BTH OR NOT?

  Thank you

  I can't find any reference to bluetooth for your model, sorry.

• Acer aspire 5742 laptop computer g does not start or it does not charge

  When I plug the laptop to the charger the light to signal that the laptop is does not load computer up.the light laptop too turns not on. I tried to remove the battery and wait five minutes before turning back, but it still does not work I don't know what to do.please help me!

  Hello

  If the screen is not an Acer Aspire Logo appears when you try to turn on your laptop, remains empty, something is wrong with the hardware.

  If at all, nothing appears on the screen and no lights work contact Acer or a repair shop, local. :

  http://support.Acer.com/us/en/default.aspx

  See you soon.

• Help! -Acer Aspire all-in-one touch screen after upgrade Windows 8 Pro

  Hi all!

  This is a rather confusing questions and about * me off no end!  I know that some of you may have encountered this already and could have a potential solution?

  I have an Acer Aspire all-in-one, AZ5101 (Aspire Z5101), with 4 GB of RAM, etc..

  Since the Developer Preview of Windows 8 came out, I've been running Windows 8 perfectly.  I completely uninstalled (each time itself) and run the following:

  Windows 8 Developer Preview, 64-bit

  Windows 8 Preview of consumer, 64-bit

  Windows 8 Preview, 64-bit version

  In any case, on this PC worked perfectly - y INCLUSIVE of the TOUCH SCREEN.  I never had a problem.

  So far so good.  Then, they finally released updates Windows 8 Pro official licensed by download.  I bought the upgrade and downloaded.  Just like in * ALL * other cases, upgrade, I chose "keep nothing" of the old system (I never really got all the important data on here), and do the upgrade itself.

  After the upgrade was complete, and ALL Windows 8 Pro updates have been applied by Windows update, I have a system where the screen is clear and precise, everything works, and all devices in Device Manager, show the Greens well, it works fine - NO ERRORS.  HOWEVER - NO CONTACT!  No touch no screen function at all.  The screen now has this time as a standard monitor.

  I tried the driver Idéacom - no luck.  Anyone know (please? LOL) how to get the touch screen to work again?  Thank you very much!  I really appreciate any help you can give.  Microsoft technical support had NO idea and no reply emails from Acer! Laughing out loud

  Thanks again,

  Mike

  [edited to conform to the guidelines]

  Hello Mike

  I sent the pilot. Please test and advise.

  Kind regards

  FReeZA

• I have an acer aspire 3690 and I am trying to restore windows xp to its factory settings how to do that

  I have an acer aspire 3690 I am trying to restore to factory settings and is only let me go back to a certain date all I want on that, that's what org. came on the computer and the internet I do not have any disk

  Page 28 of the manual of your system describes how use the built in Acer eRecovery Management software to restore your system to factory settings.

  Doing so will scan all your personal data and when you did, I think you need to configure your Internet connection again since the factory settings are unlikely to know everything about your current installation of Internet.

  If you experience a problem with your system, I think I would fix rather whatever is the problem, but here's what Acer has to say about it:

  The manual is here:

  http://support.Acer.com/us/en/product/default.aspx?modelId=5

  This article reads as follows:

  Recovery and restore features allow to restore or restore the system
  a factory default image, leave a user created image or previously
  created backups of CD and DVD. You can also reinstall applications and drivers for your Acer system.

  1. press on + or select Acer eRecovery Management of the
  From Empowering Technology toolbar to start Acer eRecovery Management.

  2. position yourself in the restoration and recovery page by selecting the button restore.

  3. Select the point of backup you want to restore from. You can also
  choose to restore the system from a factory, to retrieve a default image
  already created CD/DVD or reinstall applications and drivers.

  4. follow the on-screen instructions to complete the process.

• Error not allowing Windows not start

  My computer with Windows Vista, will not start.  It tells me that there is an error in my Windows application and allow me only so that it starts in repair mode.  In this mode, request a "another user name" and password... There is not a game I know.  If I hit F8 to try to start in safe mode with guests he brings me the same startup repair... help!  Thank you!

  Hello

  If you can get into the BIOS, I suggest you follow the steps in the following article to boot from the drive:

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-from-a-Windows-7-installation-disc-or-USB-flash-drive

• Error when starting Windows Vista and recovery system, 0xc00000f

  When I restarted my laptop, Windows Error Recovery appeared.

  None of these options (for example, Safe Mode) worked to solve the problem.

  The next page (Windows Boot Manager) appeared subsequently.

  Message from windows:

  Windows could not start. A recent hardware or software change might be the cause.

  File: \Windows|system32\config\system

  Status: 0xc00000f

  Info: Windows could not load because the system registry file is missing or corrupt.

  I tried to recover my windows using Recovery DVD of ASUS N2034 V1.0 15G3560310C0, but facing the error in the middle of the recovery process. I chose Windows recovery on partition 1 of the HD, because I don't want to lose my data in another partition. Message from Windows:

  Cannot open the WIM file

  Big red error message

  Hello

  1. who is the manufacturer of your computer?

  2 were there any hardware or software changes made on the computer before this problem?

  Try to start the computer in recovery options and then make a form of system restore it and check if it helps:
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

  Need to do a fresh install, it would be useful to know what was last removed or installed before this started.

  It will be useful.

• HP envy 17 can not boot windows or using recovery DVDs after the replacement of the motherboard

  Hi all, I need your help

  first of all sorry for my English but I'm from Greece. I really don't know a lot about the mobile only very basic computer.

  I have a hp envy 17 3d 2080en with windows 7 Home premium which, after overheating, chips to the motherboard. I ordered and installed a used motherboard from China (part 630793-001 hp number).

  After that I tried to start the laptop, but when he opens he said probably due to the change of the material he cannot start windows normally. After reading a lot on the internet, that I tried using the recovery DVDs I had prepared before the problem, but they will not start just yet. Then, I tried to use the cd system repair but again no luck.

  I looked in the bios as some people say on the internet and realized that the product number and serial number are different from those of my laptop and it's maybe part of the problem, but I don't know. I looked in other posts about similar problems, but did not get a definitive answer and this is why I post for your help.

  Thanks to you all

  Nikos

  IF YOU HAVE AN HP LAPTOP (MINE IS HP ENVY 3D 2080EN) THAT YOU HAVE CHANGED THE MOTHERBOARD WITH ANOTER ONE (MINE WAS FRIED OVERHEATING) AND AFTER REPLACING YOUR LAPTOP DOES NOT START AND YOU CAN'T FIX IT WITH SYSTEM REPAIR DISC OR DOES NOT PERFORM A CLEAN WINDOWS INSTALL OR DON'T LISTEN NOT A RECOVERY CD/DVD RECOVERY THEN EXPERTS HP WHO KNOW NOTHING. LOOK IN YOUR BIOS, AND IF YOU SEE THE PRODUCT NUMBER OR SERIAL NUMBER DIFFERENT THAN THOSE APPEARING ON YOUR COMPUTER (USUALLY IN THE BATTERY COMPARTMENT) THEN GO TO A HP SERVICE ALLOWED AND TELL THEM TO HAVE YOYR TATTOOED BIOS. WITH THE TATOO (COST US $ 40), THEY WILL REPLACE THE NUMBER OF BAD PRODUCT AND/OR THE SERIAL NUMBER WITH YOUR MOBILE PHONE NUMBERS AND YOUR PROBLEM IS SOLVED. MY MOTHERBOARD HAS BEEN FRIED TO OVERHEAT AND I BOUGHT A USED ONE FROM CHINA. AFTER I REPLACED IT THE LAPTOP WOULDN'T START AND WOULD NOT ALLOW ME TO REPAIR DVD HE OR EVEN THE USE OF RECOVERY. I CALLED HP SUPPORT, I EVEN JOINED THE HP FORUM TO ASK FOR HELP AND I GOT ONE EXPERT WAS USUALLY TRY THIS OR TRY THIS. DON'T LISTEN TO THEM. FINALLY, I READ AN ARTICLE FROM THE INTERNET THAT EXPLAINED THAT WHEN YOU CHANG THE MOTHERBOARD / SYSTEM BY ANOTHER THEN THE BIOS REFERS TO THE NEW PRODUCT NUMBER, MOTHERBOARDS AND/OR THE SERIAL NUMBER AND THIS WAY THERE IS INCOMPATIBILITY WHICH DOES NOT ALLOW WINDOWS TO START, YOU CAN NOT REPAIR WITH SYSTEM REPAIR DISC OR IT DOES NOT PERFORM A CLEAN WINDOWS INSTALLATION OR A RECOVERY CD/DVD RECOVERY. ONCE YOU TATOO THE BIOS THATS IT. THE LAPTOP WORKS. I HOPE THAT THIS MESSAGE WILL HELP SOME PEOPLE WAISTING THERE TIME AND SPEND THE MONEY FOR NOTHING

• Receive an error message that Windows can not retrieve information about the disk when I try to put upgraded Windows XP to Windows 7.

  XP Home to Windows 7 upgrade Peoblems

  I can't update my laptop to windows 7, that he will enter the upgrade options, then it will say cannot retrieve information about this disk of computers. What should I do I deleted all leave them and still get this error. Thanks Chris

  It's a little late for this, but anytime you do an upgrade, you must be sure that your computer is compatible. My guess is your drive for windows 7 is a DVD and you have a CD or a witch of CD - RW drive can not read CD

  http://Windows.Microsoft.com/en-us/Windows/downloads/Upgrade-Advisor

• Acer Aspire E1 - 572 G Bluetooth does not work after update to 8.1 Windows

  After the upgrade to Windows 8.1 x 64 bit, my bluetooth does not detect and cannot be detected by other devices (my laptop). In Device Manager, I have NO yellow exclamation points with triangles, when I search automatically updates, windows says everything is up to date (see photo below), so everything looks very well and running. Bluetooth is on, but after research found no devices (even if the phone is also activated bluetooth). Could someone help me please? Thank you very much.

  

  Uninstall the BT adapter, right click on the Device Manager and select uninstall.

  then restart and install this drivers in support of Acer:

  http://global-download.Acer.com/GDFiles/driver/wireless%20LAN/wireless%20LAN_Atheros_10.0.0.263_W81x...

• Acer Aspire S7 - 391 modernized, external mouse not recognized.

  It does not recognize the optical mouse that comes with it, should have a usb receiver?

  I got it yesterday. I bought it with the cupons to use collective emachine. It does not include a usb receiver, but he may not need one? I did an installation of a new search for the device. He didn't find. It is also my first time with windows 8, so I may be missing something?

  I accidentally found! Under the battery door is a button to make it sinc. Thanks it works now!

• During the installation of a program, receive the error message that Windows Installer is not installed properly on Vista

  I tried to install a program and I got an error message that says "Windows Installer" is not installed correctly and I need to contact the support staff.  I get also a message when I log that says steetings.ini is occupied by another program and it will not allow the sidebar to come.

  Try the Windows Installer Cleanup utility to troubleshoot the problem with Windows Installer:http://www.softpedia.com/get/Security/Secure-cleaning/Windows-Installer-CleanUp-Utility.shtml.

  For the issue of the Sidebar, do a boot minimum http://support.microsoft.com/kb/929135.  If the problem goes away then it's just a matter of tracking down the culprit at the origin of the problem.   Follow the procedures described in the article.  Once found, remove, delete, disable or uninstall.  Once remember to put Vista in normal status, as described in the procedures. If the problem occurs in clean mode then just restore the system to normal and reboot - this solution will not work.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.