Acer still support the Aspire M1610?

Similar Questions

• Do you still support the edition of Adobe Photo Album starter

  Do you still support the edition of Adobe Photo Album starter?

  Laughing out loud

  This product has been replaced by photoshop elements, now in version 11.

• CS5 will still support the MCE Blu - ray on Mac Pro Player?

  It's basically my question:

  CS5 will still support the MCE Blu - ray on Mac Pro Player?

  It is y harly any info the hardware on the web site of Adobe support more. It's just all hype sales!  They used to tell you which disks have been supported, but now that still seems to just be an afterthought in CS5, there is not ehardware in detail everything that is taken in charge and what is not...

  This new MCE Blu - ray player looks like a wonderful solution, but only if Encore CS5 on Mac would support it.

  Thank you!

  I am positive that your Mac Pro has the connectors. The SATA cable it can be somewhat difficult if you're not comfortable deleting some parts with a screwdriver, but I found it very easy.

  Cables SATA sitting around, I had had a little long boxes on the ends of the connector forcing me to have to remove a small amount of plastic from the piece of fan housing. I think that if you buy a kit from OWC cable they include cables that are lower profile but whatever it is, it's not too bad. I just use a dremel to remove a small piece about 1 "x 1" directly above the ports. "

  Here are some instructions I found: http://www.newertech.com/downloads/nwtmpqxe32.pdf (Note: the pages in this guide are all mixed!) These guys here sell a kit that delivers these unused ports of SATA to eSATA ports.

  You will see that they have low profile cable I was referring to that and so they didn't need to cut the case fan at all. I would say just OWC (www.macsales.com), because they know what you are looking for and you can sell a kit that has the cables you need, including 4-pin-power to SATA power. I recommend you to install the two cables while you're here, so if you later decide to add another SATA drive or an SSD, you will not need to take off again. BTW, add an OCZ Vertex 2 60 GB SSd drive as my boot drive for the OS and applications has been the single most visible upgrade I did and makes the Mac Pro just smoke! Same value as I just pasted the small SSD up there in the optical Bay without a mounting kit, and it works great!

  In all honesty, theough, the external enclosure for Blu - Ray works well and is easier to access the drive, because it is now located on my desktop. If you're uncomfortable to disassemble your machine just get quadruple housing interface with the chip set Oxford 934DSB that I can guarantee you that it works out of the box. It cost $140 for the whole machine, not bad compared to the alternatives.

  The reader is this: LG WH10LS30. Looks like it's still on sale for Newegg $79 until the end of the year.

  Housing I have is the following: BYTECC ME535-Limited-BK. Another $60. The OWC, looks a lot prettier in a Mac environment but costs $40 more for the same features all in brushed aluminium.

  I've been creating and burning with yet but Roxio Toast 10 Titanium burns and the authors of the Blu - Ray just wanted to make a CD/DVD

  Good luck!

• Photosmart Printer 6520: Is the driver for Photosmart 6520 still supported by Mac OS Sierra, until I update?

  Is the driver for Photosmart 6520 still supported by Mac OS Sierra, until I update?

  Hello @JeffVirant - greetings!

  Thank you for visiting the Forums from the HP Support! It is a wonderful location to converse with the community, get help and advice.

  Printer HP Photosmart 6520 is compatible with MAC OS Sierra. Please go ahead with the upgrade

  You can download the MAC Sierra drivers for your printer from here: http://hp.care/2feP2V6

  Please let me know if that solves the problem, or if you need assistance.

  See you soon

  Please click on 'acceptable' on the post that solves your problem to help others to find the solution. To show gratitude for my help, please click the 'Thumbs Up icon' below!

• I downloaded version 5.7 of Lightroom in order to support the captive capture on my Nikon D750 and its still does not. More when I was invited to give my serial number for the update that was not the case that are on my Adobe profile, although I purchas

  I downloaded version 5.7 of Lightroom in order to support the captive capture on my Nikon D750 and its still does not. More when I was not invited to give my serial number for update is no where on my Adobe profile, although I bought and pays every month for my creative cloud for photography. Help, please

  Your subscription to cloud shows correctly on your account page?

  If you have more than one email, you will be sure that you use the right Adobe ID?

  https://www.adobe.com/account.html for subscriptions on your page from Adobe

  If Yes

  Some general information for a subscription of cloud

  Cloud programs don't use serial... numbers you, connect you to your cloud account paying to download & install & activate... you may need to sign out of the cloud and restart your computer and log into the cloud for things to work

  Sign out of your account of cloud... Restart your computer... Connect to your paid account of cloud

  -Connect using http://helpx.adobe.com/x-productkb/policy-pricing/account-password-sign-faq.html

  -http://helpx.adobe.com/creative-cloud/kb/sign-in-out-creative-cloud-desktop-app.html

  -http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html

  -http://helpx.adobe.com/creative-suite/kb/trial--1-launch.html

  -ID help https://helpx.adobe.com/contact.html?step=ZNA_id-signing_stillNeedHelp

  -http://helpx.adobe.com/creative-cloud/kb/license-this-software.html

  If no

  This is an open forum, Adobe support... you need Adobe personnel to help

  Adobe contact information - http://helpx.adobe.com/contact.html

  -Select your product and what you need help with

  -Click on the blue box "still need help? Contact us. "

• where can I find firefox for Windows 10 who support the JavaScript and Norton

  I had problems all this Sunday can not enter in the emails. bankAccounts or facebook because allways firefox41 tell me I need to install and activate JavaScript. I have Windows installed 10. My laptop is 1 year old HP. I also prefer to use Norton. What can I do? Can Andy I find an older version of Firefox in Norwegian?
  Thanks for listening.
  Michele your

  Firefox's JavaScript should be enabled by default. Can you provide more information about the messages that you have found on this subject?

  At the same time, to examine the question of Norton and your language:

  Norton has been a big topic of communication of updates for Firefox via LiveUpdate a few days before each new version of Firefox is available. But that changed with Firefox 41. Due to the change in Firefox (which was originally going to be in 40 Firefox but was delayed at the request of Norton and maybe a few other companies), the toolbar needs major changes and they are still not available yet. Norton issued a statement on this subject: https://support.norton.com/sp/en/us/home/current/solutions/v115161915_EndUserProfile_en_us

  If you want to use an updated version of Firefox that allows to run the current Norton Toolbar, there are another option. You might consider a different variant of Firefox called the Extended Support Release (ESR) for the moment. ESR is designed for businesses that require a cycle time longer between changes to the features, but anyone can run it.

  ESR is currently based on Firefox 38. It will get updates of security over the coming months, but not to get new features, so changes in Firefox 41 concerning the compatibility of the add-on will not be out for a good time.

  Norton is likely to continue to support the ESR until the new update of toolbar. After that, I don't know what they will do because normally they don't take over a small range of versions.

  If you decide to try it, here's how I suggest to install:

  Clean reinstall it

  We use this name, but it isn't about deleting your settings, this is to ensure that the program, files are clean (not incompatible, corrupt or exotic code files). As described below, this process does not disrupt your existing settings. Don't uninstall NOT Firefox, that does not need.

  (A) download a fresh Installer for Firefox 38.3.0esr of https://www.mozilla.org/firefox/organizations/all/ in an ideal location. (Scroll down your preferred language).

  (B) the release of Firefox (if any).

  (C) to rename the program folder, either:

  (Windows 64-bit folder names)

  C:\Program Files (x86)\Mozilla Firefox
  

  TO

  C:\Program Files (x86)\Fx41
  

  (Windows 32-bit folder names)

  C:\Program Files\Mozilla Firefox
  

  TO

  C:\Program Files\Fx41
  

  (D) run the installer downloaded to (A). It should automatically connect to your existing settings.

  Success?

  Note: Some plugins can only exist in the old folder. If it is missing something essential, present in these files:

  • \Fx41\Plugins
  • \Fx41\browser\plugins

• 'webplugin' does not support the maximum safety level of safari plugins

  Last night, I got connected to my Svat security system using Safari and left the computer with the browser showing all the security cameras. Early in the morning about 3 or 04:00 I was awake by restarting the computer I noticed that the OS has been updated.

  For now, I am trying to connect to my security system and Safari can not access the server. I went into properties and noticed the ['webplugin' does not support the maximum safety level of safari plug-ins] my security system stop working in windows because of the plugins for a long time so my only option is to use my mac-mini to access the system and now what happens.

  The name of the plugin in the security system is called HiDVRPlugin.dmg and the system is Svat. I tried to go to Safari preferences and enabling the plugin, but it still does not work.

  Any ideas on how to re activate or difficulty this plugin?

  Thank you

  Go back to an earlier version of Mac OS X is not an option? Or may be using a different browser?

• Cannot turn on FileVault 2: "some disc formats do not support the recovery partition" version of the OS - 10.11.4

  Hello

  I went to turn on FileVault encryption for the first time, and when I click on restart (by FileVault guests) I got a error message that says "FileVault can not be enabled for the drive. Some disc formats do not support the required encryption recovery partition. To use encryption, reinstall this version of Mac OS x on a reformatted drive. »

  I found an article from apple support for this problem with El Capitan who recommended first aid running in disk utility.  I tried this but then received the same error message.

  a little history:

  -Mac OS 10.11.4 installed running on the brand/model ADATA SP 550 SSD

  -This SSD is a 250 GB drive partitioned into two, with one of these partitions being my OS

  -J' ran this BONE of a Bay external thunderbolt

  -ssd is formatted as HFS journaling +.

  I am really confused about this error message and couldn't find much online about it.  I use a fairly recent OS install.  I installed the operating system clean and made all my preferences and install so that I can encrypt and then back up this pristine OS environment in time machine so that I could always go back to it on the line in case where things are bunk too upward.  I'd have to install yet another OS to clean and do all my long software installs and system preferences settings... SIP.  I don't know if that makes a difference, but this version of the OS that I have been cloned by superduper to this SSD partition.

  What is the brand of SSD that I?  Might that matter?  I appreciate all the comments.  I'm really scratching my head...

  Thank you very much

  To enable FileVault, you need a recovery partition, which you don't have. You can create one by reinstalling OS X.

  If you do not already have a current backup, please backup all data, and then reinstall the OS. * you don't need to erase the boot volume, and you won't need the backup unless something is wrong. If the system has been upgraded an earlier version of Mac OS X, you may need to the Apple ID and password to use.

  There are ways to back up a computer that is not fully functional. Ask if you need advice.

  If you installed the runtime Java distributed by Apple, and still need, you will need to reinstall it. It goes the same for Xcode. All other data will be preserved.

  Related support article refers to OS X 10.11 ("El Capitan"), but the procedure is the same for OS X 10.7 ("Lion") and later versions.

• computer still displays the empty ink cartridges

  Every time I print, this dialog box appears. (I replaced the cartridges)

  

  It happened for a while now.  I continue to click Black only and it prints, as everthing I was need to print is strictly black.  However, now I am trying to print photos and I need color. I need to erase this message... but have no idea how.  The computer shows the levels correct as being complete... but still, I get this message ink and only on this computer.  On the macbook, it is not pop up and prints fine.

  Someone knows how to fix this?

  I have a HP all in one Photosmart C7280 running on Windows 7.

  Thank you.

  Hi gvchick03,

  Welcome to the Forums of HP Support! I see you amirouche get a print in black ink only error or to replace the Cyan and Magenta cartridges, but the ink cartridges are filled according to the ink levels. Have you ever set printing preferences to use black ink only or print in grayscale? Even if you select only one scale or gray black it still requires all the colors and all ink cartridges pull.

  Please take a look here and make sure that the preference is not affected in black ink only or grayscale. Refer to step 1:

  Impressions of color in black and white images

  Now, I would like that you remove all the cartridges and do a hard reset on your HP Photosmart C7280, see here: reset of the printer

  Once the printer is full initialized, please replace each cartridge one by one. Now, check the ink levels are they accuse even more complete? Try printing a test page, you still see the error message come?

  Now go ahead and run HP print and Scan Doctor- it has been designed to provide users with HP and features troubleshooting fix needed to solve many common problems experienced with HP print and scan the products related to Windows computers.

  Let me know the results, I can't wait to hear from you.

  Thank you

• Satellite U300 - 10 M supports the 64 bit OS?

  Hello guys,.

  I just wanted to know, if 64-bit of Windows XP can be installed on my laptop U300 - 10 M.
  It seems that the CPU (T7300) supports x 64, as CPU - Z shows that EM64T instructions are supported.
  But somewhere else, I read that bios should also support the 64 bit OS.
  So I wonder if anyone has installed 64 bit OS on U300 and tips and tricks that I have to be aware.

  Thanks in advance!

  You can install all the BONES you want there is no problem with the installation of the OS.
  You might have only problem with Win XP 64 bit drivers.

  Still is it that XP64bit is not so popular as the Win XP 32 bit or Vista and that's why you won't find drivers 64 bit XP on Toshiba page.

  Maybe you can collect the drivers from somewhere another good luck

• X 250 boots still in the BIOS

  (Of course after update BIOS 1.23) my Thinkpad X 250 (Windows 10 Pro 1607) boots still in the BIOS. I am able to start the X 250 via F12, but this isn't the long-term solution.

  I already tried without success:

  • Windows 10 Startup Repair
  • Bootrec /fixmbr
  • BIOS:
    Optimized by default
    Secure boot disabled
    UEFI and legacy
    First inherited
    Only legacy
    Disable "Run Prevention" (https://forums.lenovo.com/t5/ThinkPad-X-Series-Laptops/X240-cannot-boot-windows-7-64-bit-after-upgra...)

  You have any ideas? Thanks - Michael

  The keyboard was the troublemaker! Due to an unstable connection mainboard-keyboard F1-keytrokes were transferred at random. Thus, the laptop in these cases began with the BIOS.

  I have to ask the support of Lenovo for a stable connection (the little black part fixation was broken)

  Thank you all - Michael

• < Duplicate > what languages will support the lollipop?

  Android has been its interface translated into 57 languages since version 2.3 (now the list is still larger), on the version of kitkat there notable omissions (I am touched by the catalan, but there are others).

  Which is the list of languages that have the lollipop next android version? I hope there is a good news for us.

  Hello! I've got Motoral G 2014 and it does not support the Catalan language. Why is this?

• CMD does not support the UCN paths

  I'm running on Windows Small Business Server 2011 Standard

  When I try to make a file beats for a video game called Minecraft to host a server using CMD, CMD comes up with this error:

  CMD. EXE was launched with the path under the current directory.
  UNC paths are not supported. Or by default in the Windows directory
  CMD does not support UNC paths as current directories.
  The system cannot find the path specified
  Press a key to continue...
  The lines of code that I type in the bat file is the following:
  OFF @ECHO

  BINDIR SET = % ~ dp0

  CD /D "% BINDIR.

  "% ProgramFiles%\Java\jre7\bin\java.exe" - Xms1024M-Xmx1024M-jar craftbukkit.jar

  BREAK

  I tried the search and said to use the word pushd and popd instead of CD. But I did not write that.

  I also found a site from Microsoft telling me to edit the registry using regedit.exe I went in the shell and make a new value DisableUNCCheck REG_DWORD.

  
  

  I restarted my PC but I still get the error, can anyone help me with this?

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT ProTechNetpublic. Please post your question in theTechNet forum.

  http://social.technet.microsqoft.com/forums/en/smallbusinessserver/threads

  Hope this information helps.

• Game screen disappears, but still have the music.

  When you play Drawn, disappears from the screen, but I can still hear the music. There is no icon in the lower bar of back inside as the computer says it is still ongoing. This is the correct version for this computer and I can play for about 10 minutes before that happens.

  Try to update Windows and install the latest service pack for Windows.

  Make sure that your graphics card driver is up-to-date and also contact the game manufacturer support.

• Get 643 and 646 error codes when you try to install Windows Update. Everything else works with updateing, Itunes and other updates, but not Microsoft. I did what is listed here as much as I can understand, but still have the problem.

  Every time my computer upgrades, they fail to install.  I tried the fixes on the web site and still have the problem.  Errors are 643 and 646.  I continue to download and and keep not install correctly

  Hello sugarlake,

  Thank you for using the Microsoft answers Forums.

  Solution for error 646:

  Disable all Firewalls and try to install the updates and the stand-alone installation (download manually).

  Reset the Windows Update components

  http://support.Microsoft.com/kb/971058

  Restart the computer after the update is installed.

  Also check with

  http://social.answers.Microsoft.com/forums/en-us/vistawu/thread/6e716883-7af4-4A9F-8665-2f4dd57eee8d

  http://support.Microsoft.com/kb/822798

  That should solve the problem.
  _________________________________________________________________

  Solution for 643:

  It is a common problem with the updates of the .NET Framework.

  http://support.Microsoft.com/kb/923100
  http://support.Microsoft.com/default.aspx/KB/976982

  http://www.networknet.nl/apps/WP/archives/324

  Follow the steps in the web links above to solve the problem.
   
  That should do the trick for you.

  Thank you.

  Kind regards

  Augustine.

  UDAY $012 please let me know that whether the solution worked or not, I thank you and appreciate your comments. URGO. C