Acer XC-605 does not work with VGA monitor
I just bought it, SNID is *. I may have made a mistake, as I bought it without a new screen, thinking the old man I would have worked.
My monitor is an HP w2007v with a VGA port. There is a VGA port on the back of the Acer tour, I thought that there should not be a problem, but there are. My monitor says that he receives no signal from the computer. What I need to get a new HDMI monitor, or she would work with an adapter HDMI / VGA?
If I have to buy a new monitor, which is better to connect it to the computer? The installation sheet short I said can I use DVI, VGA or HDMI, all the same, but this is not the case. I would say there was a small cap on the the computer's VGA port, but it was not written on the box that I couldn't use it. I thought it was a protection for the transport. So, why is there a VGA port if I can't use it?
[private under the leadership of life]
So, I don't know a lot about the HP monitor, but I hope I can help to explain what you're looking at.
I have attached a picture of the back of an AXC-605, there may be slight differences, but overall, it should look familiar.
Let me start by explaining what is the VGA port on this system. Almost every Office mainboard has a VGA port available. This is because the video is a requirement for the P.O.S.T. process. The reason why it is not used is because the unit has a dedicated video card which is more powerful and the system is configured to use this dedicated card and not to provoke a conflict with the built-in VGA port. Is it possible to use the VGA port? Probably, but you lose a lot of performance with the sytem.
The image options are highlight in slot 13, HDMI and DVI. The best way to connect a VGA monitor would be with DVI to VGA connector. Those who are about $ 3-5 in the States.
Hope this helps,
Cory
Tags: Acer
Similar Questions
-
Need password on wake up does not work with two monitors
I use a laptop with a second monitor attached. I have the settings set to sleep when I close the lid, and then request a password on the reactivation. He does not sleep, and if the second monitor, but when I open again the cover, it does not require a password. It works fine when I don't use the other monitor, so I don't know what the problem is. Any ideas?
Hello
1. it worked before?
2. how to connect the second monitor? What is an extended display?
3. what happens when you wake the computer from sleep mode? Are you able to look at the screen in the second monitor and the laptop successfully?
4. What is the brand and model of the computer?
Method 1:
I suggest to turn off the prompt for password then that sleep and you can reconfigure the second track again and check.
Method 2:
If the problem persists, update the card graphics card and see if it helps.
See the links below for more details on the update of drivers:Updated a hardware driver that is not working properly
http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctlyUpdate drivers: recommended linksHope this information helps. -
Acer Liquid e700 - does not work with a SIM of UK of 3 card
I have a card SIM of EE and O2 works well but the 3 SIM card still has a red cross on it.
The SIM card works fine in my Samsung Galaxy Note.
I know the 3 network in the United Kingdom is 3G only and has no support for GSM standard phones, but I thought the e700 was fully 3G.
Anyone have any ideas?
only a 3 G SIM card, the other 2 are only 2G but you can activate via software instead of move SIM between slots.
-
DVD player does not work with Windows 10 on Acer Aspire 5553 G
DVD player does not work with Windows 10 on Acer Aspire 5553 G. I waited for a fix of Windows a whole year now and I have tried several fixes that didn't work. Are there new solutions for this problem?
http://community.Acer.com/T5/Windows-10/5553g-Windows-10/TD-p/375386/page/2
-
I had a computer repair man replace my hard drive and restore my laptop and now my orginal key does not work with the copy of vista it has installed and it won't validate how can I solve this
I have an acerDiagnostic report (1.9.0027.0):
-----------------------------------------
Validation of Windows data-->
Validation status: invalid license
Validation code: 50
Validation caching Code online: n/a, hr = 0xc004f012
Windows product key: *-* - XY9X3 - JDXYP-6CJ97
The Windows Product Key hash: xFQJU8srKsovk6p1Lk1yW93in4E =
Windows product ID: 89583-OEM-7332157-00211
Windows product ID type: 2
Windows license Type: OEM SLP
The Windows OS version: 6.0.6002.2.00010300.2.0.003
ID: {F20B4B72-1308-45BE-8F90-95E91A3F0AAF} (1)
Admin: Yes
TestCab: 0x0
LegitcheckControl ActiveX: N/a, hr = 0 x 80070002
Signed by: n/a, hr = 0 x 80070002
Product name: Windows Vista (TM) Home Premium
Architecture: 0 x 00000009
Build lab: 6002.vistasp2_gdr.110617 - 0336
TTS error:
Validation of diagnosis:
Resolution state: n/aGiven Vista WgaER-->
ThreatID (s): n/a, hr = 0 x 80070002
Version: N/a, hr = 0 x 80070002Windows XP Notifications data-->
Cached result: n/a, hr = 0 x 80070002
File: No.
Version: N/a, hr = 0 x 80070002
WgaTray.exe signed by: n/a, hr = 0 x 80070002
WgaLogon.dll signed by: n/a, hr = 0 x 80070002OGA Notifications data-->
Cached result: n/a, hr = 0 x 80070002
Version: N/a, hr = 0 x 80070002
OGAExec.exe signed by: n/a, hr = 0 x 80070002
OGAAddin.dll signed by: n/a, hr = 0 x 80070002OGA data-->
Office status: 109 n/a
OGA Version: N/a, 0 x 80070002
Signed by: n/a, hr = 0 x 80070002
Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3Data browser-->
Proxy settings: N/A
User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
Default browser: C:\Program Files (x 86) \Mozilla Firefox\firefox.exe
Download signed ActiveX controls: fast
Download unsigned ActiveX controls: disabled
Run ActiveX controls and plug-ins: allowed
Initialize and script ActiveX controls not marked as safe: disabled
Allow the Internet Explorer Webbrowser control scripts: disabled
Active scripting: allowed
Recognized ActiveX controls safe for scripting: allowedAnalysis of file data-->
Other data-->
Office details:{F20B4B72-1308-45BE-8F90-95E91A3F0AAF} 1.9.0027.0 6.0.6002.2.00010300.2.0.003 x 64 *-*-*-*-6CJ97 89583-OEM-7332157-00211 2 S-1-5-21-923204104-223683984-168055983 Acer Extensa 5630 Phoenix Technologies LTD. V1.30 20090319000000.000000 + 00070333507018400FA 0409 0409 US Mountain Standard Time(GMT-07:00) 0 3 ACRSYS ACRPRDCT 109 Content Spsys.log: 0 x 80070002
License data-->
The software licensing service version: 6.0.6002.18005
Name: Windows Vista, HomePremium edition
Description: operating system Windows - Vista, channel OEM_SLP
Activation ID: bffdc375-bbd5-499d-8ef1-4f37b61c895f
ID of the application: 55c92734-d682-4d71-983e-d6ec3f16059f
Extended PID: 89583-00146-321-500211-02-1033-6002.0000-0042012
Installation ID: 004511331255365043724851364501374781338933223323713385
Processor certificate URL: http://go.microsoft.com/fwlink/?LinkID=43473
The machine certificate URL: http://go.microsoft.com/fwlink/?LinkID=43474
Use license URL: http://go.microsoft.com/fwlink/?LinkID=43476
Product key certificate URL: http://go.microsoft.com/fwlink/?LinkID=43475
Partial product key: 6CJ97
License status: Notification
Notification reason: 0xC004F063.Windows Activation Technologies-->
N/A--> HWID data
Current HWID of Hash: OgAAAAEAAgABAAIAAwACAAAAAwABAAEAeqjWy6pVxGJ6f0DXhgfkNoBBsJzy9ErM1F/eG4QdrFYqhQ isActivation 1.0 data OEM-->
N/AActivation 2.0 data OEM-->
BIOS valid for OA 2.0: Yes
Windows marker version: 0 x 20000
OEMID and OEMTableID consistent: Yes
BIOS information:
ACPI Table name OEMID value OEMTableID value
APIC APIC PTLTD
FACP INTEL CRESTLNE
HPET INTEL CRESTLNE
START PTLTD $SBFTBL$
MCFG INTEL CRESTLNE
SLIC ACRSYS ACRPRDCT
ASF! OEMID OEMTBL
SSDT BrtRef DD01BRT
SSDT BrtRef DD01BRTAh! -in this case, it is not necessary.
I see from my records that a similar case has been solved by uninstalling and reinstalling the update WAT - KB971033
Open the Windows Update - click the link view updates installed on the left of the page
in the list, find the WAT update KB971033, and then uninstall it.
Then restart and reinstall the update from here - http://support.microsoft.com/kb/971033
redemarrer restart again, then try to change your product key to the one on the sticker - what is happening this time?
-
Previously worked perfectly with the following:
Computer (Windows 7) supplied with monitor connected to monitor with original DVI cable
Laptop Dell Inspiron 5547 (Windows 8.1) with a HDMI output connected to monitor via an HDMI to DVI I bought from Dell.
Two computers worked with the VGA cable supplied with the monitor. Now the VGA is intermittent. I tested the cable with another computer and there is no problem.
NOTE: I've never had the monitor connected to 2 computers, while they were on or while the monitor is turned on.
Now, the monitor doesn't not with DVI - video display. The laptop cannot detect the monitor under control panel > display > screen resolution. It only detects the built-in monitor. I can't check this on the desktop because there is no video display.
I also bought a display port > HDMI adapter but read messages explaining the need for a converter, so I'll ignore for now it does not work with DP since I may have the wrong card.
I followed the instructions to reset and diagnostics to the screen, which makes no difference. The problem is not at all, not only a bad display.
Is still of Dell do not repair out of warranty monitors? I bought the monitor directly from Dell and I find it rather hard to believe that there is no way to repair $ 300 monitor that is only 3 years old.
Any suggestions would be welcome. Or am I out of luck, and to buy a new monitor?
You run properly bid. He says on page 31, 'you can run diagnostics integrated only when the video cable is unplugged and that the monitor is in self-test mode'
So no DVI or VGA connected monitor.
-
It does not work with macbook air 2008! What should I do?
It does not work with the macbook air 2008 os x 10.5.8. What should I do?
What does not work?
More details please!
-
I just noticed that my code (in my blog site), which is a regular code that allows the image to transform into its form in grayscale and cast its original color, does not work with the Mozilla Firefox browser. But with other browsers, it works. I hope you can help me with this little problem. Thank you!
Should I use a CSS rule that is similar to:
filter: grayscale(100%)
This property is not yet implemented in Firefox. It is supposed to be implemented in Firefox 34, according to https://developer.mozilla.org/en-US/docs/Web/CSS/filter
-
I installed the new iCloud (v5.2.1.69) and found that it does not work with Outlook 2016 (16.0.6965.2053). There is no button "Options"... "to"Mail, Contacts, calendars and tasks"(see photo). In addition, the iCloud Outlook add-in does not display in Outlook. I tried to reinstall the Office 365 and iCloud, but nothing has changed.
I have exactly the same problem with the latest version of iCloud. I have Outlook 2016 and 10 Windows and when I try to install iCloud there saying "set up" next "Mail, Contacts, calendars and tasks. I left it for hours and it does not go beyond this point. Outlook displays the listed add-in but it is not doing anything. I tried to remove all of the Apple software, and then reinstall iCloud without result. I've deleted and reinstalled MS Office and then tried to reinstall iCloud - once again no luck.
-
keyconfig does not work with FF 24.0. Is there a way?
I just finished rebuilding my PC from a hard drive format. In doing so, I loaded the last 24.0 FF.
Part of my essential app is a script used keyconfig causes a single copy to send the source page to the Clipboard, where the script analysis. Unfortunately, keyconfig does not work with FF 24.0.Writing for easy copy begins to explain how acting on a combination of keys, rather than the action of the mouse, without the use of keycopy - but then told how he has no need, because it's too much effort, and besides - keyconfig exists and does the job - which, I agree, he used, very well - but it is no more.
What should do? If there is no other way, can I get a downgrade of FF that works with keyconfig?
There is a new add-on, key config (note the space), but it does not what keyconfig did.
The end of the thread main support doesn't mention a major problem in Firefox 24: keyconfig 20110522 - mozillaZine Forums.
Did you install from source: http://mozilla.dorando.at/keyconfig.xpi
Is the problem that Firefox won't let you activate keyconfig, but the dialog box opens, or you can activate or extension allows you to create shortcuts but they do not work?
-
I have a mac 10.5.8 software. I downloaded moxilla firefox 24 and has replaced the old version to download. Then I got a message that firefox 24 does not work with my software. How to bring back the old version?
Hello patcouse, if you want to stay with you older version of the OS, then firefox 16 is the last version available that will run in this environment. for a download link, please refer to the Firefox no longer works with Mac OS X 10.5 (at the end of the article).
-
The CD/DVD does not work with El Capitan 10.11.5 on Macbook Pro
Hello everyone, I spent the time to research on the here and the other site on why the CD/DVD does not work with El Capitan 10.11.5 on MacBook Pro mid 2009. This discussion forum has said that he will not work with the El Capitan software. Any idea or suggestion? Back to Marverick or Yosemite? I tried to use SMC reset, restart, recovery and still the same issue.
I thank in advance.
~ Mike
I have my doubts that the (10.11.5) software is the problem. Are you sure that the DVD player is simply not defective? Have you tried to clean the lens? What is the State of the disc?
Your best option may be a date at a bar in engineering of the Apple store for a FREE evaluation.
Ciao.
-
SQLite Manager does not work with the v11. Until that make it easier to return to older versions or newer versions stop, breaking most of the modules I use FirefoxHow to come back at 10 Firefox?
Update Firefox 23.0 which published yesterday afternoon.
-
I have Norton Security Suite provided by Comcast. Norton Toolbar does not work with Firefox 17.0.1 on my Win 7 machine. I lived all the questions on this topic and did all the steps and when I click on "Add-ons", he always says that the toolbar is not compatible. It works with IE, but I prefer to use Firefox.
I had the same problem in the past. If you call customer Norton service toll-free they have always helped me start (without charges) when I have updated to a new version of Firefox - seems to happen every time even if I run the updates regularly. Hope that this phone help-Norton support is always very friendly and helpful-just Google their 800 number.
-
How can I get a previous version of Firefox. 17 Firefox does not work with online banking
How can I get a previous version of Firefox. 17 Firefox does not work with banking online edit
Similarly I cannot now (with v 17) start a download from a Web site to Quicken. At least it seems with four different financial institutions, I've tried. Each of them worked before version 17. I am now on 17.0.1 so that does not solve the problem.
Maybe you are looking for
-
Displayport ENVY causes battery lose detection and performance max brightness
I have a HP ENVY 17 - 3D was released in early 2012, running Windows 7. It has 1 HDMI port and 2 additional display ports. The graphics card is ATI HD 7690 M XT and supports switchable graphics on the fly. The processor chip is 2nd generation Intel Q
-
Everyone works with Godex printers and labview before? My ultimate goal is printing labels for the products on an assembly line that are tested with an ETA developed in LabView. Because of the flexibility of our production lines, a lot of images is
-
I'm looking for instructions on how to 'listen', an audio book I recorded on MP3 player. I tried to set the mode Audio CH and have turned this 'works' and selected a speed allowing to hear the audio book, now I want to play and I have no idea how to
-
CD ROM drive not in Device Manager
Suddenly, my CD-ROM drive doesn't work after I plugged a flash drive. It does not recognize a disc (tells me to insert a disc after that I already have). The drive is not listed in Device Manager. I followed the instructions of regedit and led nothin
-
How to enable 4K HDR on XBR55X700D
I got my XBR55X700D a few weeks, and today I got my Pro PS4. The Pro tells me I am out in only 2 k HDR. I know that this TV supports 4 k HDR output but I can't seem to enable it, no matter what I do. I did these things: Update TV changed from HDMI to