ACL for PIX 6.3.1

Similar Questions

• Downloadable ACLs for users of VPN

  Hello

  I replaced the old pix with ASA (7.2). There were groups configured for the remote VPN users authenticated through the ACS and ACS download a specific ACL for each group to the PIX. After the replacement, users cannot establish the VPN connection. After troubleshooting, I discovered that the downloadable ACLs were not working very well. When I disabled this option the established tunnel. When I get back to the old pix with the same configuration, it works very well with downloadable ACL option. I opened a TAC case and he said the v3.0 ACS (I) are not compatible with the ASA. He did not really convince me and he asked to try to use the option to pair AV. I tried option pair AV with ASA and it did not work also. can you please advice.

  Hello

  Check out this point,

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCef21184

  In addition, 3.0 is very old, and I guess that in this version, we have "Downloadable PIX ACL" and not "downloadable IP ACL", on ASA download able ACL will work but with "Downloadable IP ACL" but not with "Downloadable PIX ACL".

  Kind regards

  Prem

• Order of operations for PIX

  I intend to migrate from ducts in the ACL, and I'm interested to know the order of operations.

  Lets assume that I have access list on the external interface that allows the packet HTTP & HTTPS to the Web server. However, on the DMZ interface I encouraged only SMTP packets.

  Do I need to allow packets to the Web server on the DMZ interface?

  Can't control the before State of ACL table PIX?

  (Please let me know if there is any document which deals with the order of operations.)

  Thank you.

  I'm a little confused by your example, but I think I know what you're looking for.

  Yes, the PIX search a connection exstablished front of LCD. Therefore, if the package has been allowed in through the ACL on your external interface on a server web DMZ, the answer would automatically be allowed. You must enable explicitly all traffic through the ACL on the interface DMZ that you wanted to come (initiated, this isn't an answer) of the web server on the DMZ. For example, open a web browser on the web server itself should be allowed.

  And ACL have a higher priority than the pipes so mix are not a good idea (just an info).

  Scott

• Where Smartphones blackBerry is my memory last? Ugh! No memory for pix!

  Hello

  I tried to take a few pictures with my storm last night when I was at a party and when I tried to do, I got an error message.

  I can't show you a picture, you cannot add attachments, but the error message reads:

  (letter i icon) File system error

  (the folder icon) / Device memory/home/user/photos

  Name: IMG0007-200... (name of the photo)

  I looked everywhere that I have air...

  I went to the Options... Memory and looked at what I had available. Here's what I found:

  Application memory

  Free space: 9.6 MB

  The device memory

  Total area: 879.2 MB

  Free space: 0.0 KB

  Multimedia card

  Total space: 7.3 GB

  Free space: 5.6 GB

  Of course, the glaring problem is that I don't have ANY free space on the device.  Where everything is?  I have a 8 GB memory card and I have uploaded about 150 songs in my Storm. However, I have not downloaded photos or anything else. What happened to all the memory?   Where everything is?

  I tried a couple things like turn market, pulling out the memory card, etc... I tried to attach the storm and then sneaked in the records themselves and the only things I could find in ALL files was my MP3 files.

  Anyone know what's happened here?

  Thank you!

  Rob

  I just thought the "battery pull" solution, but how do I make my memory card a 'default' location for pix?

  Thank you!

  I will go ahead and try this battery pull and tell you how it goes...

• Downloadable ACLs for users?

  Hi all

  5.4 ACS, I need ACL customized for users.

  My scenario:

  There is a way to use some "downloadable ACL" profile of permission but I want to set specific ACLs for some exceptions. For example: the user A and user B obtain permission profile 'X '. But user B is not allowed to access a host. This 'refusal rule' I will configure with custom in the internal user store attributes.

  Is this possible? How can I implement this rule?

  Best regards

  Stefan

  Hello

  You can do this by following these steps:

  1. define a user attribute of Dictionary defined under the Administration of the system > dictionary > identity > internal users call him what you want and make sure that the value is a string

  2. create the DACL in the objects of the Authority appointed under section of the political elements

  3. under the user account you will see now one filed for the dictionary name you call in step 1, make sure that the domain is the DACL, that you created in step 2

  4. create your dynamic authorization under "common tasks" defined profile as the decline of the low DACL select internal users and set the value to the attribute that you created in step 1.

  5 card authorization policy to the access policy using the conditions that will give you these results.

  6 test and you should have what you are looking for.

  Thank you

  Tarik Admani
  * Please note the useful messages *.

• What version of PDM for PIX 6.3 (4) on a 515E?

  I loaded the last PDM bin 4.1 (1) for PIX os ver 6.3 (4) but I get an error message when I try to access the new PDM:

  "Cisco PDM 4.0 for FWSM does not work on PIX. Please install Cisco PDM 3.0 on your PIX"

  Hmmm a Pix Device Manager which does not work on PIX? The links were wrong on the cisco.com page that pointed me to this location?

  http://www.Cisco.com/cgi-bin/tablebuild.pl/PIX

  Are these compatible versions?

  Here's my version:

  Cisco PIX Firewall Version 6.3 (4)

  Cisco PIX Device Manager Version 4.1 (1)

  Yes, this message is absolutely right, version 4.x PDM is just for the firewall Switch Module and is not supported by the device of PIX. FWSM supports Transparent firewall features that the PIX does not now support.

  Version 3.0.2 PDM.

  There will be a new PDM with the PIX OS 7.0 version in the first quarter of 2005.

  sincerely

  Patrick

• Q for PIX-525 spec (failover FE) and the GBIC

  Qestion for PIX-525 spec.

  1 PIX-525-UR-GE-BUN(2GE + 2FE). I want to use 2GE as inside and outside interface and failover FE. I found a doc who must use the GE model 535 failover. Is it supports statefull failover FE model 525?

  2 PIX-1GE-66 map PIX 525, is the built in card GBIC interface, or do I module GBIC order (ex, WS-G5484) to put into the card?

  Thank you

  1. the restriction on the use of a dynamic rollover interface that corresponds to the fastest interface on the PIX is the PIX 535. The PIX 525 cannot switch the line traffic GE rate if this restriction is lifted on the 525 platform. You can use a link FE on a PIX 525 as the dynamic link even if you have GE links as other interfaces.

  2. the GE on the PIX interface card contains a multimode SC connector. No GBIC not necessary... just of cables.

  I hope this helps.

  Scott

• Counters of ACL for group VPN indicates zero even if there are traffic

  Hi all

  I use a PIX 515E. I defined a remote user VPN, its pool of addresses and also set several ACLs that apply to traffic originating from this address pool of servers on the inside network.

  Does anyone have ideas why the ACL hitcounts remain at zero, even if my remote users always access the servers?

  Thanks for the wisdom!

  Joe

  Joe,

  Your probably using the command "sysopt connection permit-ipsec.

  As quoted in the PIX guide on cisco.com:

  "Use the sysopt connection permit-ipsec command in IPSec configurations to allow IPSec traffic to pass through the PIX firewall without a verification of statements of led command or access-list"

  The list located on the external interface is bypassed by this feature.

• Syntax error of ACLs in PIX list after upgrade, need urgent help!

  Hello everyone

  We have a facility including Cisco ACS + a VPN 3005 concentrator and a PIX 515E (7.2.4)

  We have improved the version 7.0 to 7.2.4 PIX and suddenly our downloadable access list has been getting refused when authenticated users against GBA.

  What radius of debugging in the PIX we found typing this line in the list of downloadable access gives the error and prevent users from the ACL list.

  "deny ip any 192.168.0.0 0.0.255.255.

  PIX refused to treat their auth request when it encounters this line.

  Very well, we said, we changed the ACL syntax for that: deny ip any 192.168.0.0 255.255.0.0

  Does the PIX treat the ACL.

  We were happy to some time until what VPN users started complaining.

  It seems that the VPN 3005 cannot process the syntax we entered the PIX!

  VPN 3005 does not seem to be able to manage the acl line "deny ip any 192.168.0.0 255.255.0.0.

  It can handle that "deny ip any 192.168.0.0 0.0.255.255!

  Who cannot manage the PIX...

  I am a loss for what to do here...

  We got the VPN users who cannot surf now with these problems of ACL.

  What can I do? Someone else encountered this?

  We have improved the VPN 3005 to the latest SW version

  Really need help here guys!

  Thank you

  I don't think that Cisco has never changed anything on the PIX. It uses from day one subnet masks as far as I KNOW and Conc VPN use masks with joker as IOS. You can use the convert-netmask-acl command on the SAA to solve this problem. In this way, you define a willdcard ACL on the ACS/AAA server, then use this command on the ASA to use the downloadable ACLs even for both devices (PIX, VPNC).

  http://www.Cisco.com/en/us/docs/security/ASA/asa81/command/ref/A2.html#wp1622944

  Please note so useful.

  Concerning

  Farrukh

• VPN for PIX 515 allowing access to a single host

  I have already setup on my PIX 515 a VPN connection, which allows the user to connect to our network via a cisco VPN client to access network resources.

  I want to configure now is an another VPN connection that external users can use but would only allow access to a host.

  E.g. I would like to VPN in my site but would be allowed to access the 10.1.1.1 on my network.

  How can I do this? What I have to install VPNGROUP another and somehow an access list to allow only traffic to a host of configuration. Can anyone help with the correct syntax for the PIX.

  Thank you

  Scott

  You will now have a bunch of commands "vpngroup" in your PIX, simply go into config mode and add more commands 'vpngroup' but with a different groupname. The VPN client then uses this group name to connect to the PIX.

  Another way to allow only access to a host for this PIX is to split tunnelling on this group, as well as in the tunnel of split ACL set only as a host.

• Apply an ACL for a VPN tunnel

  Hello

  My PIX is currently configured to allow all traffic IPSEC enter my network (sysopt permit-ipsec connection). I would like to change that so that I can define what traffic is permitted (and off).

  My installation is simple (IMO). I only have the value default outside & inside interfaces. I guess I can control "outbound VPN traffic" in an incoming ACL inside interface.

  But how can I control what traffic is allowed when entering the VPN tunnel? I don't have any interface to apply this since it is a VPN tunnel.

  And I can't apply to the external interface, I think that, given that traffic arriving on this interface is ESP traffic, so encrypted and of course, I want to be able to define what is allowed in based on what looks like the decrypted packet.

  Any thoughts anyone?

  Thank you and best regards,

  Kevin

  IPSEC traffic is decrypted before going through the outdoor LCD. When you browse the ACL, the Source address and destination correspond to the real IPs. So to accomplish what you want is easy, just remove the sysopt permit-ipsec connection and change your external LCD, using the real IP as Source and Destination addresses.

  For example, you have a vpn lan2lan with your inside network 10.10.10.0 24 and a remote control inside the 172.20.0.0/16 network and you want to give to this network access to a web server to the 10.10.10.33 just add a line

  acl_out permit tcp 172.20.0.0 access list 255.255.0.0 host 10.10.10.33 eq 80

  Access-group acl_out in interface outside

  acl_out will end up with a mixture of address public and private Source and it is ok, the PIX don't care.

• How to set ACLs for a volume?

  Hello

  I'm sharing installation points on my external hard drive (in El Capitan Server) and he said:

  "Failed to save the access control list.  Make sure that the access control lists are enabled on the volume. »

  There used to be a way to do it from the server application.

  Can any tell me how to proceed?

  Thank you!

  A few things to look at.

  First of all, if it is a new drive, you reformat to make sure it is formatted in HFS +?  Some external drives are preformatted with alternative formats of partition.  For example, if the drive is formatted in FAT I think not that he supports the ACL.

  Then, if the drive is formatted in HFS +, there is a chance that your player is set to ignore permissions.  Select the drive in the Finder and information.  Reveal the section sharing and permissions of the window read the information.  Check the status of the 'ignore property on the Volume' and make sure it is not checked.

  Also, I suggest that you do not share an entire drive.  Instead, create a folder on the root of the drive and then created folders within the folder.  The reason is that the root of the disc contains a number of hidden files that have specific uses.  For example. Spotlight is to search for and .fsevents for file system events.  You don't want mess you with permissions on these hidden folders.

  Reid

  Apple Consultants Network

  Author - "El Capitan Server - Foundation Services.

  Author - "El Capitan Server - Collaboration & control»

  Author - "El Capitan Server - Advanced Services '.

• cmd key does not not for pix not adjacent selection

  Cmd key doesn't work is not for the nonadjacent selection of pix. Worked in iPhoto, but not since the 1.0.1 Photos.

  It works in other ways as being one by design or just a default keyboard?

• Need help of the ACL for SMTP

  All,

  First thanks for all assistance.

  I am trying to configure my ASA5505 to accept SMTP relay and the ACL\Static I have created does not work.

  Here is the config:

  ASA Version 8.2 (2)

  !

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.2 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP 12.12.12.1 255.255.255.248--> deleted

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  Speed 100

  full duplex

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  switchport access vlan 3

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  passive FTP mode

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  access-list 101 extended permit tcp any host 12.12.12.1 eq smtp

  inside_access_in of access allowed any ip an extended list

  access-list sheep extended 10.10.10.0 any allowed ip 255.255.255.0

  pager lines 24

  Enable logging

  debug logging in buffered memory

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  MTU 1500 dmz

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 0.0.0.0 0.0.0.0

  public static tcp (indoor, outdoor) interface smtp 192.168.1.5 netmask 255.255.255.255 smtp

  inside_access_in access to the interface inside group

  Access-group outside_in in external interface

  Route outside 0.0.0.0 0.0.0.0 12.12.12.2 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  Enable http server

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  management-access inside

  dhcpd outside auto_config

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  World-Policy policy-map

  class inspection_default

  inspect the icmp

  class class by default

  !

  context of prompt hostname

  Please help me :-(

  Thank you very much!

  Hi Jim,.

  The configuration guide will provide a few basic examples for setting up groups of items:

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/configuration/guide/objectgroups.html

  Single network objects are only available in 8.3 and higher. However, a group of objects to 8.2 can certainly contain a single member.

  -Mike

• Backup AAA for PIX

  I have a PIX with the following configuration:

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + (inside) host 192.168.1.1 77777 timeout 5

  RADIUS Protocol RADIUS AAA server

  AAA-RADIUS (inside) host 192.168.1.1 Server 77777 timeout 10

  AAA-server local LOCAL Protocol

  AAA authentication GANYMEDE serial console +.

  AAA authentication enable console GANYMEDE +.

  order of AAA for authorization GANYMEDE +.

  AAA accounting correspond to aaa_acl inside RADIUS

  Everything works fine when the RADIUS server is available. When he is not available, I can log in with the username "PIX" and "password". The problem is, once I connected, I can't get permission to execute orders. Does anyone know of a command that is similar to the "if-certified" for routers that I can use?

  There is no method of backup for authorization for the PIX. As you know, if the RADIUS server is down, you can connect with "pix" and the password enable, but it doesn't help a permission. The only thing you can do is wait the GANYMEDE server back to the top. I'm sorry.