[ACS 5.2] Administration of switch using SSH

Similar Questions

• How to use Ssh and Https for PC8164 PC5524

  Hello!

  How to use SSH and Https to connect to PC8164 and PC5524?

  Kind regards!

  For SSH configuration, we want to watch the 1651 page controls, user guide.

  (config) #crypto console key generate rsa

  RSA key generation started, it may take a few minutes...

  Complete RSA key generation.

  #crypto console key (config) generate dsa

  DSA key generation started, it may take a few minutes...

  DSA key generation complete.

  Console (config) #ip ssh server

  For HTTPS orders, we look at page 255, 1770-1778, CLI Guide.

  generate a crypto certificate of console (config) # 1

  Console (config-crypto-cert) #key - generate

  output console(config-crypto-CERT) #.

  Console (config) # ip http secure-certificate 1

  Console (config) # ip http secure server

• Access PIX using SSH when connected remotely with VPN client

  Hello

  I think that this should be a fairly simple for someone to sort for me - I'm new to PIX configuration If Yes please excuse my stupidity!

  I changed the config on our PIX to allow only access via SSH (rather than via telnet as it was previously configured)

  Now, everything works fine when I'm in the office - I can connect to the PIX using SSH without any problem.

  However, if I work from home and connect to the office using my VPN client (IPSEC tunnel ends on the PIX firewall itself) I find that I can not connect to the PIX.

  I have configured the PIX to access ssh on the office LAN subnet and the client pool of IP addresses used for VPN connections by using the following commands:

  SSH 172.64.10.0 255.255.255.0 inside

  SSH 192.28.161.0 255.255.255.0 inside

  where the 1st line is reference to the office's LAN, which works very well, and the 2nd line denotes the IP address pool configured on the PIX for VPN access.

  Can someone tell me how to fix this? I have the feeling that its something pressing!

  Thank you

  Neil

  Try the command "management-access to the Interior.

• To connect using SSH after cloning a VM via IP not MachineName

  Is it possible to connect to a new VM Linux via the static IP address assigned by vCAC (network profiles) and not MachineName using the menu option "connect using SSH?  All the pre-reqs are completed to enable the option of SSH menu and the action plan has the custom property as machine.ssh set to TRUE.  I use TeraTerm as my SSH Manager and it attempts to connect to my VM but ultimately failed because his link is: ssh://MachineName.

  At this point, I don't have any automatic method to create a DNS entry for the new MachineName with its static IP address.  So is - it possible to change the link created at: ssh://static_ip

  All Windows VM provided by vCAC seems to work very well for RDP being the connection attempt through the static IP address instead MachineName.  I work with 5.2 vCAC.

  
  

  There is a fix to support who will do what it takes. Basically, the fix does the SSH option connect in the same way, the RDP session connects.  You should apply the fix to support if want this option.

• map a drive using ssh

  I need to map a drive samba from windows xp sp3 by using an ssh tunnel, could someone provide me with a complete walk of how to do

  1. Install this official patch from Microsoft: programs that connect to IP addresses that are in the loopback address range may not work as expected in Windows XP Service Pack 2
  2. Reset
  3. Click 'Start' / 'Settings' / 'control panel:
  4. Double-click on "Add Hardware":
  5. Click "next".
  6. Wait for this screen to go:
  7. Select ' Yes, "I have already connected the hardware" and click "next":
  8. Select "Add a new hardware device" and click "next":
  9. Select "Install the hardware that I manually select from the list" and click "next":
  10. Select "Network adapters" and click "Next":
  11. Select "Microsoft":
  12. Select "Microsoft Loopback Adapter" and click "next":
  13. Click "next":
  14. Click on "Finish".
  15. Click 'Start' / 'Settings' / 'network connections ':
  16. Right-click on "Local area connection x" and select "Properties":
  17. Uncheck all the boxes but "Internet Protocol (TCP/IP)":
  18. Select "Protocol Internet (TCP/IP)" and click "Properties":
  19. Enter an IP "Local". Local IP addresses include 10.x.x.x, 172.16.x.x and 192.168.x.x. In this example, we will use. Then click 'OK ':
  20. Uncheck the "notify me when this connection is limited or no connectivity", then click on 'close ':
  21. For Samba based systems, you can connect to 127.0.0.1. For Windows-based systems, you must connect to the local system or public IP address. If you don't already know the local IP address of the remote system, you can run on it to find out. For example, you use, you must type:

  C:\ > ssh remote.example.com ipconfig Windows IP Configuration Ethernet adapt Local Area Connection: suffix the connection-specific DNS. :... IP address: 192.168.1.101... subnet mask: 255.255.255.0 gateway.... : 192.168.1.1.

  If you are using, type:

  C:\ > cd /d "C:\Program Files\PuTTY" C:\Program Files\PuTTY > remote.example.com PuTTY

  Enter your user name and password, and then type:

  adapter for $ ipconfig Windows IP Configuration Ethernet Local network connection: suffix the connection-specific DNS. :... IP address: 192.168.1.101... subnet mask: 255.255.255.0 gateway.... : $192.168.1.1 logout

  1. Establish a connection and the port prior to port 139 of IP address () of our card loopback short above () IP address of the remote system. For example, using type:

     C:\ > ssh-L 192.168.10.1:139:192.168.1.101:139 remote.example.com

     If you are using, type:

     C:\Program Files\PuTTY > putty - ssh-L 192.168.10.1:139:192.168.1.101:139 remote.example.com

     If you wish, you can add the username and/or the password in the command line:

     C:\Program Files\PuTTY > putty - ssh-L 192.168.10.1:139:192.168.1.101:139-l user - pw switch remote.example.com

  2. Run to map the network drive:
     "C:\ > net use * \\192.168.10.1\sharename /user:"192.168.10.1\username ""password ".

     For example:

     "C:\ > net use * \\192.168.10.1\c$ /user:"192.168.10.1\administrator ""admin password"drive Z: is now connected to \\192.168.10.1\c$. The command completed successfully.

  3. For the port 139 before every time that you run, add the following to your file:

  Home remote.example.com 192.168.10.1:139 192.168.1.101:139 LocalForward

  Now, you can simply type:

  C:\ > ssh remote.example.com

  1. If you use it, you can make this connection by installing and configuring the package automatically

  MCP. MCDST. LVL 80

• AAA ACS RADIUS ASA administrative access

  We have an ASA 8.2 we'd like to AAA to configure ssh access using a 5.5 running ACS RADIUS.

  Can get users authenticate, but ASA retains user record in user EXEC instead level privileged EXEC.

  Installation on the ASA:

  RADIUS protocol Server AAA rad-group1
  AAA-server host of rad-Group1 (inside_pd) rad-server-1
  key *.
  AAA-server host of rad-Group1 (inside_pd) rad-Server-2
  key *.
  authentication AAA ssh console LOCAL rad-group1
  AAA authentication telnet console LOCAL rad-group1
  HTTP authentication AAA console LOCAL rad-group1
  AAA authorization exec-authentication server

  Have you tried pushing various combinations of these attributes of the ACS:

  Value CVPN3000/ASA/PIX7.x-Priviledge-Level = 15
  Value of RADIUS-IETF Service-Type = administrative (6)
  Cisco-av-pair value = "" shell: priv-lvl = 15 ""

  Hi Phil,

  You are able to manage the privilege level is assigned to a user with Ganymede, however, you are not able to go to privilege level without enable authentication, unless you go to 9.1 (5) code.

• What that means, "Web service is disabled. An administrator can activate using the application server? »

  I am trying to connect to a Web site that I am using for 5 years and more. Now Firefox reports that the certificate is incorrect, and the message "Web service is disabled. An administrator can activate with the server application. ", is given.

  I don't know what to do with this information. Service Web is on other Web sites. What is the "server application? How to take control and connect? I am the administrator.

  Are you able to reproduce this problem with another browser?

• Satellite 1400-103: do I need a Wlan switch use a PCMCIA WiFi card

  I have been using broadband through my usb ports on the fixed network and have recently upgraded to wireless router hub to give me the portability. Having realized that my hub router does not come with a pcmcia card or of dongel I am looking to buy a pcmcia (pc card) card.

  My problem is that the laptop will allow wireless comms since there is no wire pass under the floppy drive as described in the manual and on later versions. Do I have this switch or card pcmcia will do everything what I need (there are two slots for cards available and the manual talks about ability CardBus).

  Do I have to worry about the ability of Wireless LAN in my computer or the pcmcia card will do everything?

  Ideally, I would just buy the pcmcia card, plug it in (plugnplay pilots to kick XP) and I won ' t need to do much more.

  Any advice on this would be appreciated before that I have spend £ 20 on a 32-bit pcmcia wireless card.

  concerning

  Andrew

  I agree with chain.
  The minPCI wireless network card is not removable on an easy way and therefore the hardware switch is to enable and disable the WLan functionality in different situations.

  The PCMCIA card is an external card, which can be removed in 2-3 sec.
  The withdrawal of this card will also disable the WLan functionality.
  Accordingly PCMCIA cards don t need the hardware like wireless minPCI network card switch

• Control relay with Boolean switch using DAQ assistant 9481 - problems

  Sorry for what may be a stupid question but I'm stuck in quicksand.

  I use a relay module 9481 and have two external relays connected lines 0 and 1.

  When I create a digital output 0 line by line, I can run the test inside the express and activate the relay and turn off without problem.

  The generated block DAQ expressed expects a Boolean input of 1 d. (See attached photo).

  I want to connect a Boolean switch relay line disk 0. You can connect live not because the switch is Boolean and the input is Boolean 1 d - I'm a conversation in the pict.

  All plumbing lines display results, the relay never active.

  Any bunch would be greatly appreciated! Thank you

  

  Mr._Mechanical,

  Welcome to the Forums of switch OR this forum is generally intended for products OR-SWITCH [such as the NI PXI-25xx & NI SCXI-11xx], I think I know the answer to your question.

  I think the reason why it's a failure is the conversion you make generates a table of 16 Boolean [as the 'boolean to (0,1)' function creates a data I16 type] with your data more false data points 15.

  

  When you try to control the relay, he sees 16 datapoints are you Commander to a single port [channel] and so error out.

  

  My suggestion would be to use normal DAQmx digital output screw [with, he set up as ' Digital > single channel > single sample > Boolean (1 line) "] rather than the DAQ assistant.

  If you use the daq assistant, simply by using the function 'Building the table' will transform your simple Boolean data point in a Boolean array containing a single element.

  

  While the DAQ assistant is very easy to use, I recommend that you use the DAQ assistant, because this reduces the features and increases the execution time.

• It is possible to contact PCA9548A (8-CHANNEL I2C SWITCH) using USB-8451?

  Hello

  Now, I'm doing a project related to the smart battery. Now, I read data from a stack using the USB-8451 by smbus. The next step uses the USB-8451 casing to read the data of several batteries through smbus. I chose the PCA9548A (8-CHANNEL I2C SWITCH) to achieve this goal. But when I check the specification of the PCA9548A, there is a fix I2c format to read data from it, I tried several times, but still no can tell me where is the error in my code, or maybe it's impossible to communicate with this chip using USB-8451?

  Here is the fix that i2c read format of PCA9548A

  Why are you usng the script live? Have you looked at the examples of delivery for the 8451? You just need a couple of nodes property to set the rate and the address, and then use the VI to write I2C.

• How to change the administrator on a used pc

  Hello

  I bought my laptop used, and when I try to intall a program it says I have to me logged on as administrator.

  How can I fix?

  Hello

  I bought my laptop used, and when I try to intall a program it says I have to me logged on as administrator.

  How can I fix?

  Hey valbisc

  you do a right click on the seup.exe programs and then select performance administrator

  with a second hand computer, you ask for trouble if you do not reinstall the operating system

  you have no idea what this computer was used for the previous owner

  Walter, the time zone traveller

• RADIUS authentication for the switch using ISE

  Hi guys,.

  Someone did he do Radius Authentication for switch cli connection using ISE?

  We did it in our environment with ISE, but it is a challenge to give read-only access / Priv-1.

  If some users know the enable password, they can use and earn full privilege.

  Anyway to get around this other than to change the enable password?

  We have thousands of switches and won't change on each of them.

  If you have another method please advice.

  Thank you in advance.

  Well, you can set the "enable" function also be controlled via the AAA server with the following command:

  AAA authentication enable... This way server AAA will be checked for authentication for the secret to activate and use the local database as a last resort

  I hope this helps!

  Thank you for evaluating useful messages!

• Authentication certificate ACS 5.1 Administrator?

  Is it possible to authenticate ACS directors [web INTERFACE] by client certificate in the ACS 5.1?

  This link is for 4.x, which is a different product to 5.x.

  Current administrator authentication is made by name of user and password only.

  The certificate can be changed, but this only changes the present certificate to the

  the user because they are logging in the TAS.

  -Jesse

• ACS 4.1 forces Clients to use certificates for PEAP-MSv2

  I have a test WLAN I want to log on a user/pass field domain users, but also force them to use the public key of a self-signed cert from the AAA server.  Right now, I can get this working, if for example a windows client will connect to the WLAN if you set it to authenticate the server cert in the PEAP protocol options.  Unfortunately I can't prevent connection customers who have a valid user/pass but do not set or cannot set the cert to authenticate.  This would allow employees who have to say, an android or iPhone just to enter his user/pass combo and get an IP on the WIFI network.

  Can ACS be denied to all customers who themselves are not connected with the certificate of service installation?

  Authentication side certificate made by the PEAP Protocol Server is completely client-side.  It is a sad reality and a good reason to put in place things like on the desktop group policy to prevent users to bypass this security check.  The problem is in fact common to all technologies that rely on the trust of the certificate system. Who do you trust? What is the basis of your confidence? It is based on your list of root certification authorities trust that in an Active Directory environment can be controlled by policy.

  The main objective of the authentication server with the PEAP Protocol is to validate the client sends identifying information to someone he trusts. If the customer decides blindly trust everybody, there's not much you can do.  I don't know policies similar to those enforcement mechanisms available with active directory on iphone or other mobile devices.

  Because PEAP protects mainly the users to communicate their passwords to a man in the Middle, you could implement a security mechanism, incorporating the RSA tokens or another technology that ensures the password will be useless if intercepted.  Another option would be to provide a wireless connection more open then requiring these devices to establish a VPN connection.

• Change of computer, Toshiba laptop, Windows 7 Administrator, after purchasing used PC

  I bought a used PC and have problems to connect to my wireless printer, etc., because the former owner is still recognized as the administrator. How can I change this while I'm in control of this machine? [Toshiba, Windows 7 Home Premium laptop]

  The first thing you should always do with a used computer is to format the HARD drive and reinstall windows, for two reasons.

  1. you have no idea of the status of the machine with respect to viruses, malware and I dare say, kiddy po * n

  2. this procedure allows you to start from scratch with your own user accounts.