Add a scope beyond the limit of 2 TB
I am trying to find a good solution for storage management in laboratory Manager. I dug through the forums, and it seems that some people with some large data warehouses, while others for a larger number of small data warehouses.
We were doing 2 TB with 1.5 to partitions vmfs LUNS and slowly extending to the need. This has worked for us - we are a little more in the loop when data warehouses start to fill and may mitigate initially in models cloning of new data warehouses and by disabling the creation of the VM on the almost full data store without much impact for users.
A solution that would also be useful to have in an emergency should be able to add a measure of 250 or 500 GB in a full 2 TB data store. I know that 2 TB is the limit for a vmfs on a LUN partition, but I don't know if this same limit applies if there are multiple LUNS as scopes on a data store?
Is it possible to have a data store vmfs with more of a logic unit number is greater than 2 TB?
Thank you
A data store can be made up of 32 degrees, 2 TB less 512 Bytes each--> size Max. 64 to 16K
See http://www.vmware.com/pdf/vsphere4/r40/vsp_40_config_max.pdf
André
Tags: VMware
Similar Questions
-
How to go beyond the limit of age to music explicit in Xbox Music
original title: Xbox Music
Salvation of problems playing music from the xbox, explicit cannot be played because of me not being is not old enough even though I am 23. How can I fix?
Thank you
Hi Chris,
You can try the following?
1. open Music app
2 show the bar (Windows key + C) charms
3. Select settings
4. Select the account
5. Select confidentiality and settings online, which will launch xbox.com
6. connect you on the same account that you use with app music
7. scroll to the bottom of the page and change the setting for "Do you want to allow market access to explicit music, explicit videos and mature games Windows Phone" allowed.Hope that helps,
Scott -
Website protrudes beyond the limit of 800 pixels on the right wide in IE
HI - please help me with this, someone - it's driving me crazy. the URL is http://www.wuizmendez.co.za. I know enough to be dangerous and am about to leave the bits more complicated for a 'real' web designer. My problem is similar to a person earlier who had six nested tables. : O
But I can't locate the source of the problem.
I think you are missing the point to my post with the link. I gave you a start to the design of your page in a better way.
If you go here
http://www.paulgdesigns.com/wuiz.php
Once in your browser, go to the source code, select all, copy. Open a new document in DW, html is fine, or you can use php. Delete all of the code in code view, paste the source code of the link, and you have the beginning of your page. Follow some of the instructions, such as where to place your images, and you should see it come together.
If you get this pass, if you encounter other problems, just opened a new post and let's get you out staightened.
Gary
-
I get an error when I try to update the path in the system variables on my laptop Windows 7, how to add values beyond the limit of 1024 bytes? Is there another limit or can this solution go beyond the character limit?
Hi Ronald,.
Thanks for posting your query in Microsoft Community.
I understand from your description, that you have problems with the update the path in the system variables. I'll be happy to help you
1. what you trying to accomplish?
2. What is the exact error message that you receive?
3. are you referring to the limit of characters of the file name or the path to the file?
248 characters for the maximum path length and 260 for the maximum length of file name.
For more information, you can consult this article:
File naming, paths and namespaces
http://msdn.Microsoft.com/en-us/library/aa365247.aspx
For all windows questions do not hesitate to contact us and we will be happy to help you.
-
Add vNIC PortGroup scope with the REST API security group
I created a security group within the reach of a PortGroup via the REST API. Now, I'm trying to add a vNIC, also via the REST API.
To help illustrate, I have a JMTest1 VM with 1 vNIC connected to the PortGroup which is the scope of the security group. When I change this group the first item in the list that could be added to the security group is the first (and only) JMTest1 vNIC.
To add it via the REST API, I need to provide the following:
https://192.168.x.x/API/2.0/services/SecurityGroup/SecurityGroup-XX/members/ < member-moref >
for example I need to understand what the < member-moref > for the vNIC to JMTest1 and this is what I have a problem with.
If I add the vNIC through the user interface and then interrogate the security group it gives me below the answer:
< securitygroup >
< objectIdobjectId > securitygroup-xx < / objectId >
< type >
< typeName > SecurityGroup < / typeName >
< / type >
< name > JMTest7 < / name >
< description / >
< revision > 9 < / revision >
< objectTypeName > SecurityGroup < / objectTypeName >
< scope >
< id > dvportgroup-xxxxx / < ID >
< objectTypeName > DistributedVirtualPortgroup < / objectTypeName >
< name > dv-xxxxx < / name >
< / scope >
< extendedAttributes / >
< inheritanceAllowed > false < / inheritanceAllowed >
< member >
500758f6-b97b - 7A 79 - 0c < objectId > 04 - 996f53edf3f0.000 < / objectId >
< type >
Vnic < typeName > < / typeName >
< / type >
< name > JMTest1 - NIC 1 < / name >
< revision > 6 < / revision >
< objectTypeName > Vnic < / objectTypeName >
< scope >
< id > vm-xxxxx / < ID >
< objectTypeName > VirtualMachine < / objectTypeName >
< name > JMTest1 < / name >
< / scope >
< extendedAttributes / >
< / member >
< / securitygroup >
It seems that the < member-moref > for the JMTest1 vNIC is < objectId > 500758f6-b97b - a 7, 79 - 0c 04 - 996f53edf3f0.000 < / objectId >
If I run now:
then the vNIC is successfully added to the security group. (yay!) So I am now left with the task of how to get
500758f6-b97b - 7A 79 - 0c < objectId > 04 - 996f53edf3f0.000 < / objectId >
of a vNIC?
I have looked at the object in the Mob vCenter and via PowerCLI, but cannot see how to derive from it.
Anyone know the answer to that?
The uuid vnic is created by concatenating the vm instanceUuid + '. ' + the last three digits of the vnic device key. (The vnic is located in the area of the config.hardware.device of the virtual machine and the key will be to shape 4xxx, where xxx represents the 3 numbers you need).
-
Received a message that had been directed to a number of recipients and wanted to respond to all:, but who exceeded my limit on the number of addresses for to: and Thunderbird would not accept.
I went through a process of establishing a way to have e-mail messages to multiple recipients automatically addressed to bcc
Maybe it's a supplement that you have installed.
As part of this process, I put a limit on the number of recipients that would be treated as "to:.".
Is Thunderbird built-in AFAIK. Check your add-ons and all the settings that you can do.
-
Hi all
This should be a pretty simple question, but I can't seem to find the answer online and currently do not have the functionality to test this:
I'm using LabVIEW 8.5 and have a VI that imports data from sensor through the DAQ Assistant. In the configuration tab, there is a range of signal input. What happens if my sensor exceeds this range? I get a warning? The default value is the maximum (or minimum)? I was interested in writing a code to display an error that I approach the limits of this range, but did not know if I also need to include code to display an error if the scope is exceeded as well.
Thanks for the help,
Tristan
Hello, Tristan,.
The behavior depends on the selected range and the device you are using.
If you are using a device with a single input range is valid, we will use this range, even if you set a smaller minimum and maximum in the DAQ Assistant. So, if your device only supports ±10V and you set the range to ±8V, you will still continue to get valid data after your top sensor 8V until what you approach 10V. When you reach the limit of the extent of your device, the output will be 'rail', and simply return the maximum value until the signal is less than the maximum value again.
Note: A device that is nominally ±10V usually has a go-around (such as ±10.2V) which are usually specced in the manual.
However, if you use a device with several ranges of entry then things become more complex.
NOR-DAQmx player will choose the smallest range that entirely covers the interval you choose. For example, suppose that your device supports the following input range: ±0.2V, ±1, ±5V, ±10V and you choose 0V - 3V as the range in the DAQ assistant. The NOR-DAQmx driver will focus on the input range and the list of the entry lines that your hardware supports and choose the smallest encompassing the entire range that you set. This would be the ±5V, because this is the only beach that contains up to 3V. Thus, all between ±5V input signal is returned and none outside this range will be 'rail' to the maximum or minimum value.
We do this because using small beaches make more efficient use of the resolution of the ADC. So, we try to use the most effective range based on what you ask without picking up a range that will make you miss data.
Let me know if I can clarify it more.
-
Change the scope to the server telnet on vista home?
How can I change the scope for the Telnet Server on the local subnet only in Vista Home Premium?
I have two photos, it shows what I'm trying to replicate on XP Professional, the other shows my problem that I can not understand how more open port 23 for everyone. By clicking on the "Advanced" tab won't let me change anything either. I am logged as administrator on my own machine, but I have to be able to set up on the computer of someone else. I use my own to learn, since I created my machine as a home for Vista/Windows 7 dual pro. BTW, the icon of autocratic updates is because I did not start VIsta in some time.
http://www.Flickr.com/photos/10736018@N05/sets/72157629201945937/
Basically, I want to limit the scope for applications of telnet entering 192.168.1.0/24 subnet only IP addresses. Any other IP address should be removed by the firewall. I can't find a way to change things by using the built-in options. I disable the integrated thing and try to make my own? Outgoing requests to telnet on port 23 must be unrestricted.
I think he should focus on inbound and outbound rules rather than firewall traffic rules. There is a tab on the properties.
-
Hi all
I have seen under error in the tool main 2.2 Cisco infrastructure
The limit of the device must be less or equal to the limit of license of life cycle and also secondary device ISE inaccessible since premium.
Could you please suggest how we can solve your problem.
Thanks in advance...
Kind regards
Sachin
Yes. Life cycle license are by smart device managed. See this page for a good overview:
http://www.Cisco.com/c/en/us/support/docs/cloud-systems-management/Prime...
.. as well as this page:
http://www.Cisco.com/c/en/us/products/collateral/cloud-systems-Managemen...
.. who States:
Life cycle license: allows access to all the features of the life cycle, which includes the configuration of the devices, image management software, basic health and performance monitoring, fault management, troubleshooting and customer visibility on the network. The license of the life cycle is based on the number of managed devices. Life cycle of the licenses are available in sizes from package of 25, 50, 100, 500, 1000, 2500, 5000, 10,000 and 15 000 devices and can be combined as needed to reach a total number of device under license.
A device is uniquely identified through the assigned IP address and system object ID (SysOid). Routers, switches, light/unified access points and network first Cisco (NAMs) analysis Modules are charged on the number of licenses. If a switch stack is managed via a single IP address, it counts as a single device. A single frame will, however, be counted as multiple devices if the chassis is configured with several IP addresses. For example, a switch with several service cards, such as a firewall and so forth, or a stackable switch with an IP address assigned to each switch who is involved in the stack is considered multiple devices within the first Cisco Infrastructure. Cisco Wireless LAN controllers (WLCs), autonomous and peripheral access points third are not counted against the number of licenses.
When you have more devices that licenses, you will receive the error see you and prevented from adding additional devices to your inventory.
We see it more often when it is light (i.e. not independent) APs are added to a wireless controller. PI will not prevent the new APs to be added, they are managed under their association with the WLC. However, if you try to add a new switch it would prevent you to do until the deficit of licenses has been sent.
-
How can I increase the limit of work powershell past 16?
limited work PowerShell
I have a sequence of PowerShell 2.0 that calls New-PSSession, and Invoke-Command on this session. The command creates more than 16 processes. The problem is that CreateProcess() fails with ERROR_NOT_ENOUGH_QUOTA.
Crashed unit, got the! output of find that the number of active processes has reached the limit of employment.0: kd >! work fffffa8006e2d290 3Jobs at fffffa8006e2d290TotalPageFaultCount 125b7fTotalProcesses 3 b 9ActiveProcesses 10TotalTerminatedProcesses 0LimitFlags 2308MaximumWorkingSetSize 0MaximumWorkingSetSize 0ActiveProcessLimit 10PriorityClass 0UIRestrictionsClass 0SecurityLimitFlags 0Token 0000000000000000Assigned to this task process:PROCESS fffffa80060d7b30SessionId: 0 Cid: ill b 0, 00: 7fffffd5000 ParentCid: 0254DirBase: ObjectTable 117839000: fffff8a0028a6f90 HandleCount: 435.Image: wsmprovhost.exeHow can I increase the limit beyond 16 active processes?Hello
Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet forum.
http://social.technet.Microsoft.com/forums/en-us/categories/
You can also publish in the MSDN Forum.
Here is the link: http://social.msdn.microsoft.com/Forums/en/categories
-
Hi all
I want to know if using bulk collect into limit will help to avoid the TEMP tablespace error run out.
We use Oracle 11 g R1.
I am assigned to a task of creating journal facilitated for all tables in a query of the APEX.
I create procedures to execute some sql statements to create a DEC (Create table select), and then fires on these tables.
We have about three tables with more than 26 million records.
It seems very well running until we reached a table with more than 15 million record, we got an error says that Miss tablespace TEMP.
I googled on this topic and retrieve the tips:
Use NO LOG
Parallel use
BULK COLLECT INTO limited
However, the questions for those above usually short-term memory rather than running out of TEMPORARY tablespace.
I'm just a junior developer and does not have dealed with table more than 10 million documents at a time like this before.
The database support is outsourced. If we try to keep it as minimal contact with the DBA as possible. My Manager asked me to find a solution without asking the administrator to extend the TEMP tablespace.
I wrote a few BULK COLLECT INTO to insert about 300,000 like once on the development environment. It seems.
But the code works only against a 000 4000 table of records. I am trying to add more data into the Test table, but yet again, we lack the tablespace on DEV (this time, it's a step a TEMP data)
I'll give it a go against the table of 26 million records on the Production of this weekend. I just want to know if it is worth trying.
Thanks for reading this.
Ann
I really need check that you did not have the sizes of huge line (like several K by rank), they are not too bad at all, which is good!
A good rule of thumb to maximize the amount of limit clause, is to see how much memory you can afford to consume in the PGA (to avoid the number of calls to the extraction and forall section and therefore the context switches) and adjust the limit to be as close to that amount as possible.
Use the routines below to check at what threshold value would be better suited for your system because it depends on your memory allocation and CPU consumption. Flexibility, based on your limits of PGA, as lines of length vary, but this method will get a good order of magnitude.
CREATE OR REPLACE PROCEDURE show_pga_memory (context_in IN VARCHAR2 DEFAULT NULL)
IS
l_memory NUMBER;
BEGIN
SELECT st. VALUE
IN l_memory
SYS.v_$ session se, SYS.v_$ sesstat st, SYS.v_$ statname nm
WHERE se.audsid = USERENV ('SESSIONID')
AND st.statistic # nm.statistic = #.
AND themselves. SID = st. SID
AND nm.NAME = 'pga session in memory. "
Dbms_output.put_line (CASE
WHEN context_in IS NULL
THEN NULL
ELSE context_in | ' - '
END
|| 'Used in the session PGA memory ='
|| To_char (l_memory)
);
END show_pga_memory;
DECLARE
PROCEDURE fetch_all_rows (limit_in IN PLS_INTEGER)
IS
CURSOR source_cur
IS
SELECT *.
FROM YOUR_TABLE;
TYPE source_aat IS TABLE OF source_cur % ROWTYPE
INDEX BY PLS_INTEGER;
l_source source_aat;
l_start PLS_INTEGER;
l_end PLS_INTEGER;
BEGIN
DBMS_SESSION.free_unused_user_memory;
show_pga_memory (limit_in |) "- BEFORE"); "."
l_start: = DBMS_UTILITY.get_cpu_time;
OPEN source_cur.
LOOP
EXTRACTION source_cur
LOOSE COLLECTION l_source LIMITED limit_in;
WHEN l_source EXIT. COUNT = 0;
END LOOP;
CLOSE Source_cur;
l_end: = DBMS_UTILITY.get_cpu_time;
Dbms_output.put_line (' elapsed time CPU for limit of ')
|| limit_in
|| ' = '
|| To_char (l_end - l_start)
);
show_pga_memory (limit_in |) "- AFTER");
END fetch_all_rows;
BEGIN
fetch_all_rows (20000);
fetch_all_rows (40000);
fetch_all_rows (60000);
fetch_all_rows (80000);
fetch_all_rows (100000);
fetch_all_rows (150000);
fetch_all_rows (250000);
-etc.
END;
-
By selecting the vector shapes in mode traced that go beyond the edge of hidden form?
Hi all
In Adobe Illustrator, I often receive works of art which has the art of "junk" hidden in a hidden form. However, this art of the Junk extends beyond the hidden form and is visible in preview/trace mode. How to choose junk art WITHOUT having to expose everything?
I have attached a very basic example. Usually, I have large files with vector patterns complex that add thousands of unnecessary points that are hidden in the mask.
Ideally, I would like to be in preview/trace mode and simply select the useless pieces of art and remove them to clean the file better.
Double-click to edit inside the shape using the Mode of insulation, or simply use the lasso tool or the direct Selection tool to select the areas you want to remove, and then remove them. Don't hit delete twice, or it will remove the entire shape grouped/hidden.
-
Lightroom CC 2015 11 x 17 prints beyond the right margin - Epson Expression XP-906
In another thread of printing problem 11 x 17, I saw that the original question has not been addressed and that others appeared to have my problem have been add to the discussion, they seem related problems with print 11 x 17, but not the same exact problem. Here's my problem. Thanks in advance for reading.
It is a newer version of 6 color Epson all in one printer, and exit 11 x 17 look nice. However with the latest drivers and 10 Windows and Mac Book os X when I put in place to print a 11 x 17, every time, printing continues beyond the right margin. With margins 0.25 in. and cell size 10.50 height and width 16.50, my image extends approximately 0.125 in. beyond the right margin line. When I'm saying, I mean the short edge that is not inserted in the printer to start a unique landscape of 11 x 17 print. I took the suggestions of the other thread using a Lightroom color management profile, reduced to fit, stretch to fit, use margins without borders and always set to nothing does not. Mac and Windows 10.
I'm out of the idea and the Epson Ultra Premium Luster is expensive for just to try this or that... Anyone have the same printer, or delivers and solve it?
Once again thank you for taking the time.
Concerning
Jason C
I think I found my problem in my manual.
I've always used Epson presentation matte paper, which comes in "11 × 17 inches (279 x 432 mm)."
The new document I'm working on Epson Ultra Premium Luster Photo paper is real paper A3 "A3 (11.7 × 16.5 inches [297 × 420 mm])."
I guess that (Yes for sure me) once I put the size of the paper correctly, it will be printed within the margins of model.
Oops.
Jason C
-
How to increase the limit the max column pivot in BIEE 11 G?
Hi Experts,
How to increase the limit the max column pivot in BIEE 11 G?
When the number of columns exceeds 256 in pivot mode, it generates the error message as below:
Exceeded the configured maximum number of allowed output prompts, sections, the rows or columns.
Error details
Error codes: IRVLJWTA:OI2DL65P
Geographical area: saw.httpserver.processrequest, saw.rpc.server.responder, saw.rpc.server, saw.rpc.server.handleConnection, saw.rpc.server.dispatch, saw.threadpool.socketrpcserver, saw.threads
Publ. SQL: 13678 ~ vid1ptgt0v5ubh39gesnauuhl6
For example:
----------------Day
Country - 20120101 - 20120102-... 20121231
China - 10000 - 20000-...Try increasing the lines Max Instanceconfig.xml
Path:-Middleware\instances\instance1\bifoundation\OracleBIPresentationServices\instanceconfig. XML
300
1000
500
25
30
Try to add in the configuration file and restart the services.
Mark as correct if it is useful.
Thank you.
-
2gbsparse backup due to the limit of open files errors
Question: Is there a way to change the limit nofiles in ESXi 4.0 + so that it persists through a reboot?
On large files VMDK vmkfstools fails with: doesn't have to clone the drive: the limit of the host to open files (40)
I understand that this is because of the setting nolimit, before be reduced to 256 in ESXi 4.0 + compared to ESXi 3.5, which is the value 4096. In order to be able to backup up to a 2 TB disk, I would like to change this setting to 4096. [Fuzzy math: (2 TB vmdk / 2gbsparse) + locker hidden files = ~ 4096]. I failed to find a permanent adjustment for this. Run the command 'ulimit-n 4096' in rc.local does not work either. I tried to add the same command in the script of ghettoVCB as well, who does not work if the script is running from a cron job. I have something that seems to work, but it's messy. I added a line to the ghettoVCB.sh script that says: source vmfs/volumes/< datastore > /ghettoVCB/set_ulimit.sh
set_ulimit.sh looks like this:
#! / bin/ash
ulimit-n 4096I think that if I could run the ulimit command from cron or in rc.local I could bring the necessary change without adding lines to the script of William. However, this command can be entered interactively or automated methods are reluctant to not having the absolute path (which I can't find it). The ulimit command seems to be a hidden built-in to busybox.
nofiles limit is attached to a process and not to the entire system.
In other words, each process has its own limits.
When a command in a shell script, the fork itself, the parent will be ready to deal with the following command and the child set up the environment for the new process, including the limits set by ulimit and then run the command waited.
ulimit [-HSTabcdefilmnpqrstuvx [limit]]
Provides control over the resources available to the shell and the process started by
it, on systems that allow such control.Usually a process inherit the limits of its parent.
Concerning
Maybe you are looking for
-
CURRENTLY TO GET A DEACTIVATION OF THE SYSTEM [75101991] CODE ON MY HP LAPTOP FORGOT PASSWORD CAUSE ITS BEEN SITTING IN MY CLOSET FOR A FEW YEARS BECAUSE OF THE KEYBOARD, NOT WORKING AND HAVING TO USE A USB CONNECT KEYBOARD ANYWAY I WANT TO RESET AND
-
Satellite L555 simply freezes with black screen (White Stripes)
Hello I'm having some problems with my new Toshiba Satellite L555 laptop, it is simply freeze and appears a black screen with white bands.He don't do it regularly, but it's annoying. Any suggestions?
-
AIO HP 8610 Pro: new printer
HP sent me a printer replacement for one who does not connect. My question is, Im on the instant ink programme with this printer. How can I go on the withdrawal of this printer and registering a new one in the program of the ink? I won't be charged t
-
Skype phone with none his first time in 4 years. Not muted.
I have a Skype phone pair phone 6.0 dect, and lt went Mute while talking. Everything done to get itback. Reset computor alsol first time in four years. STI has phillips. Ive rest sounds all over the place. IM lost, HE signed yet. (deleted number)
-
installs... hanging on the new internet location provider, which was same as my old I cancelled... When my service ended and I went to check my email... the email of the person who the service I was connected to East came my computer... I got my emai