Additional non contiguous internet address space?

Similar Questions

• My laptop can open internet explore properly, the cursor may work when you tap the address space to type a Web site, but the site it does not point to the search space to find anything except the right button

  My laptop can open internet explore properly, the cursor may work when you tap the address space to type a Web site, but the site it does not point to the search space to find anything except the right button. What is the problem? Harry

  When you try to search it's inside Windows or Internet explore?
  When is this last work fine?
  You did changes to the computer?
  Has it worked before, then you can try to run the system restore and check if that helps

  ;)

• Research by ASA & ISP address space

  Hi all

  Maybe a stupid question. One of my clients planning on creating RDP access to some servers sitting on 'Inside' of ASA5510. Customer asked pulic ISP 24 address space and had a 1.1.1.0/24 (ips changed). In addition, ISP customer provided with ASA ouside I / f IP: 2.2.2.2/30 and default gateway for ASA (modem Internet service providers) such as 2.2.2.1/30.

  So what is the best way to use the ISP assigned public IPs to provide RDP access to servers on the inside... ? Can I assign 1.1.1.1/24 to ASA inside and can create a "No. NAT' to access internet and RDP.

  Or I thought initially to have NAT with ip pvt in-house system (wasn't aware of public ip address space required). So is it possible using the same ip address space pvt and assigned/24 ip addresses to create Internet/RDP access?

  Help for config links is appreciated.

  Thank you inadvance

  MS

  "I thought initially to have NAT with ip pvt in-house system (wasn't aware of public ip address space request)." Is it so possible using the same pvt ip address space and assigned/24 ip addresses to create Internet/RDP

  access? "

  Upsolutely possible and the best to do as you have thought about it.

  If I understand correctly: Please correct me otherwise!

  1. you have ASA5510, outside of the interface with the IP public 2.2.2.2/30

  2 - ISP router with IP 2.2.2.1/30

  Gives 3 - Customer ISP 254 public IP addresses using client on another beach 1.1.1.0/24

  Well, you can do the following if you do not have inside the configured IP interface.

  1 - ASA5510 inside can be any subnet ip to any of the reserved private beaches. For your inside interface you can use one of the below private beaches.

  i 10.0.0.0 through 10.255.255.255

  II - 172.16.0.0 to 172.31.255.255

  III - 192.168.0.0 to 192.168.255.255

  Assume that you have inside the 172.16.1.1/24 interface

  If you have:

  ASA5510 outside interface IP: 2.2.2.2/30

  ASA5510 inside the interface IP: 172.16.1.1/24

  for your ISP services new public IP range just create your one-to-one NAT in ASA5510

  translations by using the new IP address of the ISP. Note that the ISP should route the new public IP address space to your ASA5510 outside interface, Im sure they know that.

  As said, just create your static nat using the new public IP address, you can also create

  If necessary global nat pools.

  for example RDP access from outside with the public IP 1.1.1.100 coordinated to 172.16.1.50 PC inside the host

  static (inside, outside) 1.1.1.100 172.16.1.50 netmask 255.255.255.0 0 0

  outside_access_in list access permit tcp any host 1.1.1.100 eq 3389

  Access-group outside_access_in in interface outside

  for example, creating additional pools of global variables using the new IP PAT range.

  Global 1.1.1.50 - 1.1.1.74 2 (outdoor)

  Global (outside) 2 1.1.1.75

  Rgds

  Jorge

• I can not see the internet address bar or toolbar command on Firefox 3.6

  When I open my Firefox, it shows my home page but I don't see the window of internet address to change or what I see my options of command at the top of the page.

  See what happened to the file, edit and view menus?, it shows how to restore the bar of menus and other toolbars.

• Why our local DNS server, discount Internet user if the user insert new internet address?

  We have a local DNS server that has a strange problem. If a user insert new internet address DNS will cut this internet user. So every time that the user want to insert the new internet address that he must fix his connection and then refresh the browser to display the page.

  How can I fix this error?

  Hi Saman,
  first things first... more information is needed to correctly diagnose your problem.
  When you post a question please include at least the system operation, error message, and what happens when the issue appears.
  Second, server or business systems problems most will be better suited to Microsoft's Technet forum.
  Try this link below for search/post:
  http://social.technet.Microsoft.com/search/en-us/?query=DNS%20Server&refinement=112&AC=3
  B Eddie

• Can I change several non-contiguous single video clip segments and the remaining segments together in a functional element?

  I have a second video clip 90 I want to reduce to 50 seconds by removing 10 seconds at the beginning, 5 seconds to end & 25 seconds on average. This means that I use two non-contiguous segments in the middle. The use of 'The Start Trim Point value' a second time eliminates the segment previously created with this command. Is there a way to create the first segment, save it, create the second segment, save it, and then combine the two?

  Windows XP

  Movie Maker 5.1 (2.1.4028.0)

  I have a second video clip 90 I want to reduce to 50 seconds by removing 10 seconds at the beginning, 5 seconds to end & 25 seconds on average. This means that I use two non-contiguous segments in the middle. The use of 'The Start Trim Point value' a second time eliminates the segment previously created with this command. Is there a way to create the first segment, save it, create the second segment, save it, and then combine the two?

  Windows XP

  Movie Maker 5.1 (2.1.4028.0)

  ============================================
  The cartel command only works if the video has been imported
  in segments (this only happens when "create Clips for video
  Files are checked in the import screen.) or if the files are divided
  in the timeline with no editing. If the files are changed or re -.
  organized the handset command will not work.

  You can save segments individually if all other files are
  removed from the timeline. The original file must be
  adding to the timeline and edited for each successive change and
  record.

  Easy solution... you can combine edited clips by registering the
  the project in the. WMV format. The result will be a single. WMV
  video file.

  XP Windows Movie Maker 2.1...
  To save in a .wmv movie file...
  Type of... CTRL + P (or go to...) File / save movie file)
  to open the wizard movie recording.
  Choose... My computer.
  Next /.
  Enter a name and a location.
  Next /.
  ICT... "Best quality for my computer.
  Next /.
  Wait while the movie is saved.
  Finishing...

  Personally, I prefer to split video files and remove the
  unwanted part instead of use the trim option.

  "Split a Clip in MM2.1.

  Drag the video/audio clip to the
  Timeline.

  Read the video/audio by clicking on the
  "Play" button under the display screen.

  You will see the playback indicator
  (vertical line), advancing through the
  timeline.

  Click on the button "Pause" to the point
  where you want to split and type...
  CTRL + L or click the "Split" button to the
  at the bottom of the display screen.
  (you can also make adjustments to)
  Drag the playback indicator)

  Make splits as much as you want and
  remove unwanted in law clips
  Click on / delete.

• Update my windows xp to 64-bit increases the allowed for the ram address space?

  I have Windows XP 32-bit... If I have upgraded to Windows XP 64 bit will it allows me a greater address space for my ram?  I already know that the programs that I use currently will support 64 bit.  My motherboard will support it as well.  Like I'm looking for a solution to my problems on this model of game play.  It serves to support my game very well, but since the processor over heated (replaced fan) and replaced the graphics card, ram replaced... my gaming experience is still not was.

  It would if you could... but you probably can't.

  On the one hand, it is not only your programs or your motherboard.  You must change your CPU as well.  Is there any other hardware and device drivers.  And, of course, there is the small problem that Windows XP 64-bit is no longer available from Microsoft (you can find online, but it is not cheap and may or may not be 'authentic').

• VPN and overlapping address spaces

  I'm trying to setup a VPN to allow a business parter access our network. The problem is that the partners use the same private address space as we do.

  I'm trying to understand how the NAT address translation is internal to a different address as the packet out of the VPN tunnel.

  There is a Visio Doc attached that shows THEM and 'US'. The side "THEM" doesn't use real IPs, I made this drawing because I'm an example put in place in a lab environment, so I took random numbers for IP addresses 'THEM '.

  The PC (s) of the partner must have access to two PC on my side. I got it working until the VPN tunnel appears between the two PIX501s and translated the destination address IP in a private IP address, but need help to translate the remote source IPs in private IPs.

  Here are a few exits of the PIX on the 'US' (my side).

  ICMP echo request incoming (len 32 id 2 seq 44033) 10.150.100.100 > 216.x.x.x > 10.220.2.10

  The source of the packet is sent to the address 216.x.x.x and then translated to its internal address of the 10.220.2.10. I need to translate the 10.150.100.100 address to something else, so he isn't wasting my network. Ideas? I'm a n00b PIX. Thanks in advance.

  Hello

  Sorry I don't have Visio on my PC at home but if you want to translate the source IP address of incoming packets for example. translate 10.150.100.100 to 192.168.5.10

  public static 192.168.5.10 (exterior, Interior) 10.150.100.100 netmask 255.255.255.255

  If you have a source address pool you could do

  NAT (outside) 3 10.150.100.0 255.255.255.0 outside

  Global (inside) 3 192.168.5.10

  HTH

  Jon

• Overlapping address space question - how to NAT inside the traffic to one address different range on SAA for comms with 3rd party VPN?

  We already have a connectivity of IPSEC VPN site to site with a 3rd party.

  They must be able to access a couple of servers on our internal network but the problem, it's the subnet these servers are hosted on clashes with the address space they already used elsewhere. Thus, they asked if we can put in place a new subnet and have our firewall (running v7.2) ASA NAT the traffic to and from our servers ' real' internal addresses.

  for example

  • 3rd party 10.10.10.0/24 subnet
  • Our subnet 10.20.20.0/24 (but this clashes with the 3rd part of the address elsewhwere space)
  • Our 'real' internal server addresses are 10.20.20.1 and 10.20.20.2

  How do we setup NAT on our ASA translating internal addresses 'real' of these servers for some other addresses that don't clash?

  that is that the 3rd party is concerned, they would simply have to communicate with this 'new' subnet, say, 192.168.20.0/24 and our ASA firewall NAT traffic accordingly to allow some comms unfold?

  (And it should affect only comms on these servers for the 3rd party - NOT for one of our other multiple VPN connections! "And should not affect the other comms from the servers themselves!).

  That's what I've tried so far, for one of the servers, without success:

  On ASA:

  !

  access-list 1 permit line 3rdpartysite extended ip host 192.168.20.1 10.10.10.0 255.255.255.0
  !
  access-list SERVER-NAT line 1 permit extended ip host 10.20.20.1 10.10.10.0 255.255.255.0
  !
  static (inside, outside) 192.168.20.1 public - access NAT SERVER list

  "sh xlate" indicates:

  192.168.20.1 global local 10.20.20.1

  Can someone help with the necessary NAT configurations on the ASA?

  Thank you!

  'Clear xlate' after you have configured NAT statements?

  When you try to ping from the 10.20.20.1, get it to the ASA? You have an ACL on this interface that would block the ping? Also, can you run capture packets on the ASA to see if the ASA receives even the traffic?

  What is the subnet mask of the 10.20.20.1 host? I guess it's 255.255.255.0?

  You don't need something specific on the ASA with regard to the delivery of the 192.168.20.1.

• It is possible to select multiple non-contiguous items on a page?

  It is possible to select multiple non-contiguous items on a page? Lets say I want to apply a style to 5 different elements on a page, and they are scattered all over the page. Can I somehow select all 5 and apply the style to them with a single click?

  If you speak a different, non-contiguous pieces of text in the same text box, InDesign doesn't have this capability.

• Change of IP network address space

  Hi all

  I work with our local IT people to get a new address space that is larger than what we have currently allocated.  We currently have two class C address which are separate, but adjacent blocks.  We will migrate to a new address space which is a 22 space (4 blocks of class C).

  I'm curious to know what is the best way to migrate existing systems to new block of addresses.  Our Lab Manager users have about 50 deployed computers.  I'm not adverse to force people to cancel the deployment and redeployment can help to change, but what is the best way to manage the change of the IP address of the virtual machine itself?  LM will take care of this for us, we have to recustomize or do it manually?

  Since we have networks spanning host, is it possible to convert the existing physical network virtual and just that bridge to the new physical network?  This could be the solution of effort low right now and so let me migrate slowly / system configurations to the physical network over time.

  Thank you

  Jason

  Hi Jason,

  Couple options based on your questions:

  (a) lab Manager not automatically refreshes your virtual machine if your subnet is changed in physical network settings.  You will need to cancel the deployment/redeployment for LM to get a new IP address from the pool and recustomization on the existing VMs for the address to apply force.  If you use fences, you need to make sure that the vRouter gets also cancelled/made to implement the rules by the new addressing scheme.  You could also just manually change the IP addresses in the virtual machines but a cancel the deployment/redeployment is necessary in any event.

  (b) you can potentially convert the physical network existing in virtual (actually just create a virtual network with similar parameters.  There is no option for a conversion of this type) and how to bind V networks P.  However, with this method, you will have to add the new virtual network to each configuration and also to change the NIC of each virtual computer to connect to the new virtual network.  You will then have to cancel the deployment/redeployment configs, forcing the customization (pulling of the new pool of virtual IP networks even if it's the same subnet) and a virtual and physical link.

  I'd say you're better off with option has).

  Let me know if you have any other questions.

• Space additional BlackBerry Smartphones new address book

  I've seen a few other threads here on the new address

  Book format.  I love not so much, as others have mentioned.

  because now instead of 12 names per page-view

  (and I have a lot of contacts), I don't see that 5-6.

  I'm surprised there is no choice as to the way in which you can view your

  Address book.  Has anyone found a way around this?

  Thank you!

  No, sorry, there is not a way to switch this view on / OFF... it's the way it is.

• Panels firefox like file, edit, tool, Internet address does not exist in the first page

  Whenever firefox open there is no Panel as file menu, menu address internet etc only Web pages

  This has happened

  Each time Firefox opened

  Is Juli 7th 2010

  Hide the menu bar is a new feature of Firefox 3.6.
  Press the Alt key to display the Menu bar, then open view > toolbars and select menu bar, so it has a check mark.

• No web address space or the buttons (Tools, view, back, etc.)

  Removing a toolbar, I accidentally downloaded during the installation of software, I lost the space for entering web addresses and also all the buttons - file, view, tools, etc.. Help.

  This has happened

  Each time Firefox opened

  == I deleted the toolbar of Device Doctor

  You can hide the menu bar in Firefox 3.6 on Windows, on "view > toolbars" or via the contextual right click menu on a toolbar.
  Press in and hold the Alt key to display the menu bar.
  Go to "view > toolbars", right click on the menu bar, or press Alt + V T to select the toolbars to show or hide.

  See also what happened to the file, edit and view menus?

• Network programs Netv rk rk Internet Websted Websted URL Netv - Websted Internet address

  Hvad kan following:

  Error when starting

  Internet Explorer holdt opp at fungere med er

  En r. pa websiden, er skyld i explore holdt oppe at fungere med er

  Windoww Live Mess svarer ikke

  Disse tekster kommer igen og igen.

  Med Hotel hilsen

  By Nielsen

  Hello

  Sorry, these forums are English only.

  Please select your language from the drop-down menu, at the top of this page to post your question in the language of your choice.

  If you can't find your language above, support for additional international sites options are by following the link below:

  http://support.Microsoft.com/common/international.aspx

  Concerning