After cloning question: I cloned my hard drive storage to a bigger successfully, but now how I reconnect the old hdd?

Similar Questions

• try re-installing CS5 on a new hard drive... I forgot to remove my CS5 on the old hard drive... I have the CD of installation of CS5... I've updated from CS3 and have two serial numbers

  try re-installing CS5 on a new hard drive... I forgot to remove my CS5 on the old hard drive... I have the CD of installation of CS5... I've updated from CS3 and have two serial numbers...

  I use a PC...

  Please check Adobe - Creative Suite 5 Master Collection: System requirements and try to install the product, please let us know if you are unable to activate. You can check: error: "this serial number is not for a product calling it" | CS6 cs5, CS5.5,

  I hope this helps.

• Services Windows problems after cloning a HARD drive

  Hello

  I recently cloned my HARD for one SSD drive, using the SSD as my boot device. Since then, I was able to successfully access Windows services.

  For example, I've tried to expand a partition on my SSD and went to computer management. I got a message saying that it

  "cannot open log events on the computer service.

  I click OK and the computer management opens.

  Clicking on device management, I get a long enough message that appears that says

  'Disk management could not open Virtual Disk Service (VDS) [name of the hard drive]. This can occur if the remote computer does not support VDS, or if a connection cannot be established because it has been blocked by a firewall of Windows. For more information see on diagnose and correct this problem, see Troubleshooting Disk Management by using disk management. »

  I click OK and the message disappears.

  If I click on Services and Applications in the left pane I get WMI control and Services in the central pane.

  I double-click on Services, scroll down to virtual disk, double-click anywhere on the line, I get

  "Windows could not open the service of virtual disk for playback on the local computer. Error 1726 the remote procedure call failed. »

  Is someone can you please tell me what is happening? What have I done? Why am I not able to access disk management?

  I tried sfc/scannow and I get the message

  "Protection of resources Windows could not start repair service".

  EEK! What have I done?

  Thanks for the help, but I thought about it.

  I had turned off by mistake in my BIOS PATA, and causing the problem.

  Thank you for taking the time to respond, however. It's very appreciated.

• My hard drive crashed, I have reinstalled Windows, but now, it does not update, get error 0 x 80240036

  I GET MESSAGE FOLLOWING [Error number: 0 x 80240036] The website has encountered a problem and cannot display the page you are trying to view. The options provided below may help you solve the problem. For self-help options: Frequently asked Questions Find Solutions Windows Update Newsgroup To support options: Microsoft online assisted support (no cost for Windows Update issues)

  [Error number: 0 x 80240036] The website has encountered a problem and cannot display the page you are trying to view. The options provided below may help you solve the problem. For self-help options: Frequently asked Questions Find Solutions Windows Update Newsgroup To support options: Microsoft online assisted support (no cost for Windows Update issues)

  When you have done the clean install, what Service Pack level are you up to? In other words, you have installed SP2 and SP3?

  What version of IE are you using?

  All your drivers are up to date?

  Have you installed a firewall / anti-virus before you connect to internet software and if so, which?

  Maybe you could give some information on your system so that maybe someone can help more or maybe read this:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-windows_update/cannot-download-any-Windows-updates-get-error/fb94ba4e-6b2e-4053-8706-bb1148201110

  Also:

  How to obtain the latest Windows XP service pack
  http://support.Microsoft.com/kb/322389

  Note SP1a does not exist so if you are at the level of the RTM, go straight to SP2 and SP3.

  FYI

  Steps to take before you install Windows XP Service Pack 3
  http://support.Microsoft.com/kb/950717

  Installation of XP SP2 - http://support.microsoft.com/xpsp2getinstall

• What are compatibility problems in cloning a hard drive with 32 MB cache to a cache of 16 MB or vice versa?

  Are there compatibility issues during the cloning of a HD with 32 MB Max for a max of 16 MB, or vice versa, HD the two 500 GB drives.

  Thank you in anticipation.

  Original title: cloning of hard drives with Max different buffers

  Hi blacksmith60,

  No, there is no problem with compatibility. But, you may notice a slight change in speed and performance.

• HP Envy Touchsmart j122TX 15: cloning of HARD drive for an SSD and installation on HP Envy Touchsmart 15 j122TX

  I will replace an old 1 TB HHD by a new 1 TB SSD Samsung 850 EVO on my HP Envy 15 Touchsmart j122TX. I also have Acronis True Image 2015. How can I go on cloning of the HDD to the SSD and installing the SSD on my HP, implementation of the operating system in order to ensure a good performance? Please give me step by step instructions I'm inexperienced. Thank you for your support.

  You need a bootable media because you cannot clone Windows player while it is in use. If you start another source (bootable support) leaving the main hard drive passive and quiet, so it can be copied sector to the new clean disk. I explained you start from the Acronis Disk and when the interface is in place you select "utility" and one of them is 'clone disk '. This is how you use the bootable disc in the cloning process.

  As with the post before me you simply remove the MSSD. However, in this case the user would do a clean install. Cloning will be hover over the driver of storage for the SSD controller and will not have to load the RAID driver separately. The way you do it is much easier.  I would like to dissociate the WSSD since the main hard drive using Intel Rapid Storage (disable acceleration), remove the WSSD and start-up of the former hard drive without the WSSD in place one or two times before cloning.

• Portege S100 - upgrade after cloning BSOD & HARD disk

  Hi all

  I wonder if anyone can help me please. I have a laptop Portege S100 with a standard 80 GB drive. I want to upgrade to a 200 GB drive.
  Here's what I did.

  I ran Acronis to save an image of the 80 GB HARD drive. All backed by an external USB disk and checked. I inverted the readers and restored the image on the 200 GB drive. All restored and verified.

  I restart the PC with the new hard drive in place. "Windows XP" logo comes up, then aarrgh blue screen. Stop x7B.
  Swapped the old disk, system boots fine.
  Check in the BIOS, with the old hard drive in place that the RAID configuration is enabled by default

  New swap disk, JBOD configuration is enabled in the BIOS. Could this be why it is not booting? If I want to activate the RAID configuration, it is ok, but I'm told that it will wipe the hard drive!

  I have no qualms about wiping the new hard drive, but it will work? If I change the RAID configuration, then restore the image? The only reason why I have not done it so far is because it took some time to create the image, and then writing it back on the new disk and at that time there the owner of the laptop is needed it back. !

  Help appreciated!
  Thank you very much
  Alex

  Hello!

  Can you post the BSOD detailed please?

  I'm a little confused on RAID m parameters are you wrote. As I know the Portege S100 can handle only a single HARD disk.
  In addition, you must use the same settings as with the old HDD RAID.

  Maybe the SATA controller has a limitation of LBA 28 bit and can't handle a 200 GB HARD drive. In this case, the larger HARD drive should have 120 GB. Here you can learn more about the limitation:
  http://www.48bitlba.com

  Last but not least, you can see the new HARD drive for errors. Maybe it s faulty. For this, you can use the Drive Fitness Test:
  http://www.HitachiGST.com/HDD/support/download.htm#DFT

  Sorry, but for the moment I put t have more ideas.

  Good bye

• New hard drive try to install Windows vista but it keep suspended after 60% and collapsed them

  New hard drive try to install Windows vista, but it keep suspended after 60% collapsed I tried a few time every time I had to wait for 5 hours, but the same thing happen again and again can help you pleaaaaaaaaaaaaase

  Monastir,

  What happens when it stops it is have a Sata driver. It is on the drivers cd you received with your computer. You can also start the computer and press F2 to enter the bios. From there down to Configuration system - SATA Operation and change this to ATA. It is located to AHCI. Save the changes and restart the installation. Once you have loaded Windows and drivers installed, you will need to go back to AHCI.

  Dell-Jesse

• In Vista, after you delete all data on hard drive, now get the access denied error

  I deleted all the data from my hard drive. everything works, but I can't copy or move my files anywhere. When I opened my hard drive, access is denied. I connet Internet can´t or other. I ve tried to use the restoration of the system, but still the same.

  Hello

  ·         You met any question which did you to remove the data from the hard drive?

  ·         What happens when you try to connect to the internet?

  ·         How the hard drive is connected to the computer? Thanks to a USB or SATA cable?

  Method 1:

  Take possession of the location/folder where you want to copy the files to:

  To take ownership of a file or folder

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-access-denied-when-opening-files-or-folders

  Method 2:

  Try checking the boot, if the problem persists:

  http://support.Microsoft.com/kb/929135

  Note: Place the computer to normal startup by following step 7 from the link above.

• How many times can I install Windows 7 on your PC even after I continue to update the hard drive SSD for a bigger?

  How many times can I install windows 7 on your PC even after I continue to update the hard drive SSD for a bigger? Unlimited?

  Mike

  There is no limit.

• Am trying to re - install Acrobat 9 Pro (includes the Distiller) after installing a new hard drive. iMac 27 "2009, ElCapitan 11.11.6. I have the original dmg file. also have trid copying from back up. It seems to load correctly. When open ask for my pa

  Am trying to re - install Acrobat 9 Pro (includes the Distiller) after installing a new hard drive. iMac 27 "2009, ElCapitan 11.11.6. I have the original dmg file. have also tried copying from back up. Same thing is happening anyway. It seems to load correctly. When open it asks my password but not to its own serial number. It is open, but don't watch not at the full bar at the top, that the word Acrobat, and it does nothing? Worked very well before the old drive crashing. On the same operating system?

  Not compatible does not mean that it cannot work (even if sometimes this does not mean that). This means that it has never been tested and not be fixed; This often means people have seen strange and unpredictable issues.

  Acrobat makes changes to the system, it is always more vulnerable. DC Acribat is the current version. If the goal is to slow down completely, perhaps more profitable subscription activity.

• I use LR 6.5 on an iMAC. Files RAF Fuji originally, I imported from an SD card worked and exported in the form of PSD and then after saving the files on an external hard drive RAF erased from Lightroom. I now want to import some RAF b HD files

  I use LR 6.5 on an iMAC. Files RAF Fuji originally, I imported from an SD card worked and exported in the form of PSD and then after saving the files on an external hard drive RAF erased from Lightroom. I now have to import some RAF of the HD files but LR shows them as dazed out and said that they have already been imported when I hover over the thumbnail. I have this problem when importing files in the same HD Canon CR2, and who have been treated exactly the same. Anyone got a clue as to why this is happening? Thanks, Phil

  Hi Phil,

  If Lightroom then reads these as duplicate files, it shows that they are already present in your Lightroom Catalog.

  You can search by file name and check if the image is present in your library.

  Kind regards

  Claes

• Level question on my laptop hard drives.

  Hello

  I have 2 hard drives of pre - counter on my laptop.

  They are exactly this article: http://www.keenzo.com/showproduct.asp?ID=3288986

  I would like to know if there is a problem to be replaced by 2 more high speed drives (7200 RPM).

  And what else should I notice for compatibility for my laptop.

  For example, could switch to this http://www.keenzo.com/showproduct.asp?ID=3588508 drive

  I can see there a slight difference in the physical dimensions, but what worries me the most is the difference in the field 'shape factor' which should "Plug-in module" instead of "internal hot."

  Thank you in advance.

  Message edited by elias_sgr on 11/19/2009 09:45

  You can use this player. I think the dimensions are a mistake. The dimension that you have to be careful about is (should be 2.5 ") width and height (9.5 mm)... all laptop SATA disks except the news versions 1 to meet these dimensions (they are thicker than 12 mm approximately). Portable hard drives are intended to be and are generic, interchangeable, standard of the industry. As long as it's a SATA drive with the dimensions above above, you should be fine. Understrand to strip the caddy off the coast of the old disk before replacing with the new bare drive. Generally, you remove 4 screws in the corners of the car and then a connector any covering the SATA interface (on some models not all).

• HP Envy 860-008na: HARD DRIVE C: no space (main road), but my D: has 1.81 TB?

  Just brought my new PC and was struggling in the game with peaks of lag.

  But after restoreign to factory settings, I noticed that my C: drive has only 117 GB? Where that my D: drive (reprise?) was 1.81... TB!

  C: drive is supposed to be the essential motivation for computer? The PC is new not edited or modified... Ask yourself why this fault/problem and how to fix it.

  Here's a photo of basic while I was looking at why I had no space in C: drive and the delay of the spikes.

  As I was obliged to put games on my D: drive due to lack of space on my C: drive, it could cause a problem with lag spikes that occur?

  Cheers, need an answer as soon as POSSIBLE

  

  Hello

  I'm not a gamer but know game files are large and have to move a lot of graphic data and CPU to run correctly.

  Your new PC comes with a small 128 GB SSD (fast) and a slow 5400 RPM 2 TB HDD.

  So you have an inherent bottleneck of design. Games must be installed on the HARD drive slow or you quickly run out of room.

  The only solution I can see (there may be others) would buy a lot more SSD for the OS volume (C.) Install games on C:, instead of D:. That would eliminate the bottleneck of the data transfer.

  HP Recovery partition and recovery disks/USB can be finicky. You may be tempted to replace the slow HDD with a SSD. It would work, but you may need to buy a 2 TB or SSD of greater. The recovery discs or a USB recovery drive will be used (did you create a set of recovery discs?) to install on the new disk configuration and can choke if the replacement of SSD HARD drive does not match the 2 TB HDD. Increasing the primary disk larger than 128 GB should not adversely impact factory reinstall HP using HP recovery discs or a USB recovery drive...

  Jay

• When I try to back up my files to an external hard drive I get error code 0 x 8000700020 how to stop what is happening

  Original title: Ox8000700020

  Hi, when I try to back up my files to an external hard drive I get error code 0 x 8000700020 how to stop what is happening

  Double post: http://answers.microsoft.com/en-us/windows/forum/windows_other-performance/ox8000700020/3c708968-5d37-40dc-97ef-2a44b72ca5fc

  I have merged the new post with the original question.

  -steve