After hybernation, all usb and wifi mobile devices does not work

Similar Questions

• Satellite L300-19F and WXP - audio device does not work

  Hello

  I installed Windows XP Home edition on my Satellite L300-19f after change SATA compatibility I installed Windows XP Home edition and installed all the drivers and everything's fine, but the audio device does not work. I downloaded the driver from DOWNLOAD & support center, but he can not detect.

  BTW: he used to work on Vista.
  What should I do?
  And thank you

  -Download driver audio Realtek HD Realtek page.
  -Go to the Device Manager
  -Remove the sound card.
  -Remove the High definition Audio Controller
  -Restart the laptop.
  -Reinstall the Realtek HD audio driver

• Header and footer extending the width of the browser in mobile devices does not work

  Can someone tell me why this feature does not work in mobile devices... at least for me? I saw some sites done with Muse and they seemed to be the fact exhaust the width of the screen of the iPad for ex. My sites are all cut on the right side and do not seem to have a good explanation for this. I would really appreciate if someone will give me some comments.

  Here is an example.

  http://checkourwork.com/relivephotography/index.html

  Thank you.

  That does the trick!

  Change the width to the size of your Web site. The two below are what I've used in the past.

  These works perfect for all mobile phones, computers, laptops, computers & tablets.

• After internal reset PRAM and SMC microphone still does not work properly

  I've recently updated to el capitan. For the first time that I had to use the microphone internal, so I went to the system preference, the maximum capacity, the value clapped my hands, but the microphone reacts just as shown on the scale bar. So I reset the SMC first then the LANDAU and now it reacts a little more because I clap my hands, I want to tell the scale bar that detects the incoming sound shows like 5 spots (and there are 15 points). I tried to register and the sound of the recording is very low. Is this normal? What I need to fix my mac (3.06 GHz Intel Core 2 Duo, 4 GB of DDR3 memory a 1067 MHz, GB 999,35-909, 89 GB free)? Thanks for any response.

  Susan of morro bay , October 28, 2014 16:21
  in reply to Sirae87   Useful

  I cleaned the little tiny micro holes - and it worked:

  I also had a problem with my internal microphone. In system preferences > Sound > entry, I had the internal mic selected, and the entry level bar would show some activity when I typed in the top of the computer, but not when I spoke. So first of all, I had to figure out WHERE the microphone was actually and I googled and found this on top of my iMac - a very small circle of TINY holes, right in the Middle at the top of the screen. Turns out I have had covered with a decorative Angel, using a sealant that is usually used to stick things to the surfaces. I removed the little angel and PuTTY... but did not always receive my voice recording in the bar of entry-level in sound preferences. I used canned air to blow at the level of the tiny holes, but that did not help. Finally I found a brooch (thinking it was actually too thick, drill holes of small microphone) but I WAS able to push the small holes - so I poked each other - and voila - my internal microphone now work! Yay!

• My DVD player does not work and all the information I can find is "this device does not work correctly.

  Hi, I have Windows Vista and I use a computer laptop Dell studio. When I insert a disc into my CD/DVD drive, the drive spins and it looks like it is about to start and makes the same noise start several times and then just stops. My computer does not record that there is a disc there. If I double click on the DVD drive in 'My computer' it ejects my disc and says "insert the disc in drive E".

  I went on the 'repair' Microsoft online scanner and it told me that there is a problem, but he can fix it. In Device Manager, under CD/DVD-ROM readers I have Optiarc DVD +-RW AD - 7640S. Under device status - general - properties, it says "this device does not work correctly. He also says that I have the updated driver.

  I even uninstalled the driver as a last resort and then restarted my computer. It reinstalled the driver for me, but there was no change. Please help me!

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
  Setup after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are some registry
  entries that do not fix the resolution of problems and those who "could" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and the
  correct registry entries for your car.

  Here are the keys in my opinion, are those in question - for the CD/DVD drive of course subkeys as
  There will be other subkeys in these keys. Do not forget to ask involved specific keys as well as the
  Parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Webcam USB 2.0 on my laptop with windows vista error device does not work correctly

  Original title:

  I just plugged a usb2.0 webcam on my laptop with windows vista. It is loaded ok, but the device manager says that the device does not work correctly. Any ideas please.

  I just got a webcam via ebay and plugged into my laptop. I'm working on windows vista. He finds and load device software right away, no problem. But I can't work. go into my device manager it tells me that the device does not work correctly. Any ideas please.

  Hi Matthew,

  The first thing I would try is to connect the webcam to another computer to make sure that the webcam is not defective.

  Now, check out these links and return to the State of the question.

  When hardware installed in or attached to a computer doesn't work properly, it is often because of a driver problem.

  Here are a few common problems with drivers and the means to solve them.

  See the following link for more information:

  Tips for solving common driver problems

  Also check out the following link and run the fixit available.

  Hardware devices do not work or are not detected in Windows

  The fixit diagnose and solve problems with the equipment. (USB) Keyboard and mouse are not detected by the Manager of devices or when they do not work.

• I have iphone5s and my contact id does not work, all the time he show faild Setup touch id please help?

  I have iphone5s and my contact id does not work, all the time he show faild Setup touch id please help?

  Hi yjain51,

  I understand you had some problems recently with getting Touch ID to work reliably on your iPhone 5s. I know that it is a feature of great security for your iPhone, so I'm happy to help you.

  When you use Touch ID, make sure that your hands are free of any dirt or moisture so that fingerprints can be read clearly. This article explains further:

  Use the ID Touch on iPhone and iPad - Apple Support

  Thank you for using communities Support from Apple. See you soon!

• I'm locked out of my iphone5 not connected to my wifi at home and my home button does not work, any ideas on how to fix?

  I'm locked out of my iphone5 not connected to my wifi at home and my home button does not work, any ideas on how to fix?

  < re-titled by host >

  Take it to an Apple Store for repair or replacement.

• Satellite U400-17R - audio device does not work after installing XP

  Hello

  I bought a model U400-17R with Vista Home. I formatted and installed Windows XP Professional download drivers XP Toshiba site.

  Everything works, but my Sound Device does not work. When I check in the Manager of devices the Sound Drivers are there and it says working properly.

  I'm lost... Can someone please help?

  Hello

  I think you have the same problem like me a few months ago.
  I installed Win XP SP2

  The t is not his work because I didn't install the patches MS; KB835221 & KB888111

  The patches must be installed as a first step, before the audio driver is installed.
  If you have already installed the audio driver, then you must remove (uninstall) before install you the patches Ms.

  PS: The MS patches are part of the SP3

• Wireless device does not work after downgrading from Windows 7 to Windows Vista.

  Original title: wireless device does not.

  recently, I got my os from windows 7 to vista, now my wireless device does not work. I checked the Device Manager and the report shows that my network controller driver is not installed and the modem on high definition audio bus device. I tried to install it, but in vain. What should I do?

  If your computer manufacturer does not have Windows Vista drivers available, you're probably out of luck.  Without drivers for these devices will not work.

  'spyc' wrote in the new message: * e-mail address is removed from the privacy... *

  recently, I got my os from windows 7 to vista, now my wireless device does not work. I checked the Device Manager and the report shows that my network controller driver is not installed and the modem on high definition audio bus device. I tried to install it, but in vain. What should I do?

• Huawei Mobile Connect 3 G Modem this device does not work properly because Windows cannot load the drivers required for this device. (Code 31).

  System: Windows 7 Ultimate 64-bit. QC processor 2.5 Ghz, 4 GB RAM, Nvidia 9600GT. The work of modem very well until about a month. Uninstalles the device, I reinstalled it but the same messages. I've updated the driver and software, still nothing. In safe mode, the modem driver is loaded and the devicemanager reports that the device is functioning properly. Once the system is booted in normal mode divcemanager reports: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31). Help, please. I check the settings for the 6to4 drivers and there is no problem.

  Thanx

  Hi rui2010,

   

  Place your machine in a clean boot State to see if another application is in conflict with the modem.

  If this fails, I recommend you reach out to the community Hauwei for assistance:

  http://Forum.Huawei.com/jive4/Forum.jspa?forumid=46&orderStr=9

   

  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• I have a Hp and the micro build does not work how to fix this?

  Can someone help me please? I have a HP T5800 and the micro build does not work how can I solve this problem?

  Hello

  Check with HP, their drivers support and documentation online and ask in the forums about known issues.

  Support HP & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  ========

  It's probably the pilots who are responsible and who may not really be later or they need to be
  re-installed anyway. The best way is to manually review using the methods below.

  References to Vista also apply to Windows 7.
  
  Control Panel - device - SOUNDS - look for HD Audio Manager - Mine said RealTek High
  Audio definition (this is an example and you can have an other name/maker).

  Write the description and the model double click on it - tab drivers - write down
  Version. Now click on update drivers who cannot do anything as MS is far behind certifying
  drivers. Then CLICK RIGHT on it and UNINSTALL - REBOOT - this will rebuild the driver
  stack.

  You can have the default windows or a former certified pilot and it's all or part of the
  issue.

  Now, go to the site of the manufacturer of the system and get the latest Audio/Sound drivers - download - SAVE - go to
  where you put - right-click on Reboot - RUN AS ADMIN-

  Check the Version tab of the driver in the Device Manager as the restoration of the sound card drivers often
  and then install the latest version. Restart and check after each test, not
  rare to have to run the pilot of 1 to 4 times or more. Just the version make sure you
  installed shows upward on the tab of the driver.
  
  Go to the site of the manufacturer of the device, and then search for the even more recent drivers and install repeat
  operating mode. Download - SAVE - go to where you put them - click on - RUN AS
  ADMIN - Reboot

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers to 7 (updated drivers manually using the methods above is)
  to ensure that the latest drivers from the manufacturer of system and device manufacturers are are preferably)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  ---------------------------------------------------------

  After the updated driver.

  Click with the right button on the speaker near clock - recorders - right click in the box - check see the
  Disconnected devices and show disabled devices - check your micro - highlight
  then on lower right properties. Make sure that the appropriate injector is selected and check
  other parameters - levels tab make sure that MUTE is disabled and APPLY / OK to change.

  Also in the search for some Audio Manager Panel (perhaps named after the manufacturer of the sound driver). Mine
  is the RealTek Audio Manager, yours can be quite different name if you have one.

  How to activate Audio devices hidden in Vista
  http://www.Vistax64.com/tutorials/143447-audio-device-enable-hidden-devices.html

  Connect one microphone, music player or other audio device to your computer
  http://windowshelp.Microsoft.com/Windows/en-us/help/b0e3d7fb-1b4a-4926-8254-65da289209261033.mspx

  Problems with sound and audio or no sound - a Mr Fixit
  http://support.Microsoft.com/GP/NO_SOUND

  Tips for solving common audio problems
  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-sound-problems

  The volume of the audio recorded by sound recorder in Windows Vista or in Windows 7 is less than
  in Windows XP (or Vista)
  http://support.Microsoft.com/kb/973446

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Qosmio DX730 and Win8 - touch screen does not work

  Hello

  My wife's parents bought a Toshiba Qosmio DX730 (model PQQ11A). They have recently upgraded to Windows 8 and the touch screen does not work now.

  The problem is lack of drivers (the monitor driver reports as a generic PnP monitor).

  I have went on the Toshiba site and selected downloads driver for the appropriate model and installed a number of drivers, including recommended NVidia display drivers. There is no drivers on the site that seem to install support for Toshiba touchscreen.

  Are there no drivers available for this model Windows 8? If not, is there another solution? If Yes, where can I find them. Any help very appreciated because they have nice and bought computer Windows 8 so they could use the touch functions.

  Thank you.

  Hello

  On the page of the Toshiba UE driver you can find drivers for Win 8.
  As far as I know that you will install the Toshiba display driver for the touch function works correctly.

  I found this driver.
  Please check if you can install this:
  [Win 8 TouchScreen software for Qosmio DX730 | http://eu.computers.toshiba-europe.com/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 381 & selSeries = 366 & selProduct = 7338 & salt ShortMod = null & language = 13 & selOS = 40 & selType = all & rupload = Yes & monthupload = & dayupload = & useDate = null & mode = allMachines & search = & action = search & macId = & country = all & selectedLanguage = 13 & type = all & page = 1 & ID = 83418 & O SID =-1 & driverLanguage = 42]

• Excite Pro AT10LE-A-108: after JB 4.3 external BT keyboard upgrade does not work

  Hi all!

  After update 4.2 JB JB 4.3 does not work my bluetooth keyboard.

  Pair ok, Tablet keyboard sees but does not.
  Please, do toshiba repair package or fix problem.

  On the other my android device (phone LG with 4.1.2) working this keyboard ok.

  Sorry, my English is very bad. (Google Translator)

  Thank you.

  [Keyboard Type | http://www.trust.com/en/all-products/18441-executive-folio-stand-with-bluetooth-keyboard-for-ipad]

  Okay, please, I want to downgrade 4.2 JB for this tablet, it's possible?

• Direct3D devices does not work on Windows XP

  Direct3D devices does not work on Windows XP

  Hello
  1. what exactly happens when you try to access Direct3d devices?
  2. you get any error message?
  3. If it works well before?
  4. don't you make changes to the computer until the problem occurred?
   
  I suggest you to follow the steps below and check if it helps:
  
  Method 1: Try to uninstall and reinstall the Direct X on Windows XP:
  Here's how:
  a. open the registry editor by running Regedit from start > run.
  b. then, navigate to the following registry key.
  HKEY_LOCAL_MACHINE\Software\Microsoft\DirectX
  c. here, delete the DirectX folder, exit the registry editor and restart your computer XP.
  d. when starting the system, after the reboot, your system will be reinstall DirectX 8.1 which is originally preinstalled Windows XP operating system.
  Once it is done the upgrade to x 9 live.
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=2DA43D38-DB71-4C1B-BC6A-9B6652CD92A3&displaylang=en
   
  Registry warning:
  Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  How to back up and restore the registry in Windows: http://support.microsoft.com/kb/322756
   
  Method 2: If the problem persists, then try to install the latest graphics driver from the link below.
  http://support.Microsoft.com/default.aspx?scid=kb;en-us;179113
   
   
  Hope this information is useful.