After recovery installation DVD-RAM has dissappeared since 'my computer' - P100

Similar Questions

• When you start windows after the installation of RAM, screen sparkles.

  After that I installed RAM, I turned on my computer and the screen fizzed.

  Uninstall the RAM > work put RAM back in > Scan matching RAM to install.

  http://www.crucial.com/

  Analyzer to use on the link to find out what RAM you have t adapt it and the ability of your motherboard RAM.

  See you soon.

  Mick Murphy - Microsoft partner

• Satellite M40X-126: disk blocks when the DVD-RAM has been inserted

  Hello

  I have a laptop Toshiba Satellite M40X-126 with a super multi drive installed. I have a problem with writing to DVD-RAM. Sometimes, when I try to write data to a DVD-RAM disc, the DVD player makes a strange noise, as if the mechanic of material is blocked inside the car. The laptop will not write any data on him and he doesn't notch in this noise. And I can't open the drive, because it is blocked by the software. And windows is blocked as well, I can't do anything. The only thing I can do, is stopped the laptop by pressing the power on button a few seconds.

  I do not think, it is a software problem. I have installed all the necessary drivers (UDF) is installed correctly. And DVD - RAM writing runs smoothly most of the time. But I have every 5 times I insert a DVD-RAM disc makes it drive this strange noise and everything is blocked.

  My disc is damaged? Who has the same behavior?

  Thank you

  Reto

  Hi Reto

  I have the same drive, but it works without problem. I know that DVD-RAM media are expensive, but all I can suggest is you buy another provider and check if it will happen again.

• HDD LED continuously flashes after the Installation of RAM in P70 - no boot upward

  Hello

  I had a Thinkpad P70 since February and it works fine. It has 16 GB of RAM (Non - ECC) (2 x 8 GB). I got two 8 GB 2133 DDR4 Hynix RAM SODIMM, thinking I could switch to 32 GB total.

  I installed both modules of Hynix in the brackets of two memory under the laptop.

  When I turn the P70, it does not start. The HARD Drive LED flashes continuously. When I remove the memory modules, the machine starts.

  The memory is compatible with processors SkyLake.

  Means that it is incompatible with the P70?

  Thank you.

  Here's an update. I put the RAM in the two memory modules. Power on the computer and waited longer. The led flashed away for about a minute then stopped. Then the P70 booted up successfully with 32 GB of RAM now installed.

  This can help others - looks like I have did not wait long enough when I originally installed the two memory sticks.

• Satellite A200-17: after XP installation DVD not recongnised

  Hello everyone

  I have vista just formatted and installed XP on my laptop A200-17.
  In Vista, I could read and write CDs DVD, but as I found it now I can't read or write any DVD in XP and can only play regular CDs.

  Can someone help me around?
  Thank you

  How do you say? I assume you mean this engraving function in Solution Explorer.
  You can also use an external application to burn like Nero or CDBurnerXP to burn your files on a medium such as DVD/CD.

  Usually it shouldn´t be that DVD´s couldn t be read, but I'm not sure. That you have installed all the drivers?

  Welcome them

• DVD drive has disappeared from my computer and Device Manager lists

  The machine is an Acer laptop with a single disc DVD - RW Win Vista Home Premium 32 running with all the latest updates installed.

  I have not installed anything new (software or hardware), I know.

  The other day the player just stopped working and is no longer registered to each workstation or in the Device Manager list.

  While they inspected the system event logs there is a chain of...

  Event 7026 - the next (s) starting or starting system could not load:

  CDROM

  and...

  Event 11 atapi - driver detected an error in the controller on \Device\Ide\IdePort2.

  Event 9 atapi - the device, \Device\Ide\IdePort0, did not within the time limit.

  Event 11 atapi - driver has detected an error on \Device\Ide\IdePort0 controller.

  I know that the drive itself works well because when I initially turn on the laptop I can hear the drive spin upward and I'm able to eject the drawer, so there the power etc... but once in Windows the drive does not work or even appear anywhere.

  So far, I have tried.

  1. detection of new hardware in Device Manager

  2 - installing all IDE channels and let the system reinstall after re-booting

  3 running the Microsoft Fixit tool, it seems to point out that there is a problem and said fixed it, but nothing is actually fixed by that

  I noticed a few other posts which look similar to mine, but had trouble understanding if they truly are or not.  So apologies if this is a repeat of something already posted.

  OK tried the fixit tool still once, was not aware there were different tools for different issues.  I have the wrong tool launches the first time round.

  Anyway, the drive is still on holiday somewhere, fixit tool reports that it may not detect the drive at all, so that seems to indicate that he does not drive connected.

  Is it possible that the IDE cable has come off the promenade inside the laptop?  I hope that not because I just spent the last couple of hours trying to figure how to get to where the Player connects, but seems almost impossible... can get to all the rest, keyboard and screen disconnected, RAM, disk HARD etc, but the DVD player, not a hope!

  Looks like I'll take it to a service somewhere I guess.

• My DVD device has "disappeared" from the COMPUTER screen page and is unusable/unrecognisable. Just gone.

  I am running Vista.  My DVD drive is an Optiarc DVD +-RW AD - 5560 a ATA DEVICE.  This has happened in the past, I think that as a direct result of the execution of "update".  I am not very computer but I think it has something to do with the filters.  Dell has fixed this for me several times, but he continues to to and I would like to know the procedure to fix myself (off warranty and Dell charges a lot$ $$).  Yet once, when I click on COMPUTER, this device is simply not there.

  Hello

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  Hope these helps.

  Rob - bicycle - Mark Twain said it is good.

• P20: cannot use the DVD - RAM drive after installing a trial software

  Hi members,

  I am using Toshiba satellite P20 - 604 model - load with windows xp prof - SP2. I wasn't able to use the software from burning DVDs successfully, so I tried to install cyberlink Power2Go software (trial ver) in there and ended up with "No. DVD RAM DRIVE APPEAR" in my computer. I could see the device dvd - ram with a yellow exclamation point in Device Manager. (the drive model is MAST * A DVD-RAM UJ-811). I tried to update the driver for it, no use. No idea how to recover the original driver and make it available for use dvd - ram drive? waiting for your valuable solution.

  Thank you & best regards

  M.Kanagaraj

  Hello

  The easiest way is to use the system restore option if you have created a restore point before you have had an experience with the trial version of Power2Go. If this is not the case, check if there is a system restore point has done in recent days.

  Good bye

• Satellite pro U200 - change DVD-RAM with a BD - ROM

  Hello, my DVD-RAM has been damaged, and now he does not write data, I wanted to ask if I can change the current DVD - RAM UJ-842 model with one of them:

  1 - Panasonic UJ - 120 Blu - ray BD-ROM/8 x dvda±rw DL notebook IDE Drive (black)
  http://www.geeks.com/details.asp?invtid=BLK-Uj-120-do&cat=DVD

  2 Sony Optiarc BC-5500 has Blu - ray BD-ROM/8 x dvda±rw DL notebook IDE Drive (black)
  http://www.geeks.com/details.asp?invtid=BLK-BC-5500A-do&cat=DVD

  Thanks in advance.

  Hello

  I m not very good if this disk will work in your notebook.
  The fact is that hard drives support different master/slave/c-salt settings and wrong settings lead to error IDE #1.
  The BIOS does not simply recognize the CD/DVD drive.

  Here, in this thread someone has replaced the STRANGE with Blueray and it worked:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=139719

  Check it out

• HP dvd ram uj8c2 does not refresh on hp Pavilion

  DVD RAM has a triangle of warning next to him and I tried to correct the problem by pdating, but it says that the software is already up-to-date. The drive does not recognize any DVD/CD I put in, I would really appreciate a solution to apply, if there is a. I use Windows 8.1 if this helps, thanks

  Hello

  Try the rest of the procedure to the title of the subheading resolution - method 3: manually difficulty corrupt registry entries on the link below to remove upper and lower filters and see if that fixes the problem.

  http://support.Microsoft.com/kb/982116

  Kind regards

  DP - K

• Options has dissappeared form my top bar (the classic theme configuration) and with it, spell checker and al.

  Options has dissappeared since my top bar (the classic theme configuration) and with it, spell checker and al., search help find nothing useful, as usual. Am I the only one wondering how to access functions to be included under Options?

  You have solved my problem, and I wanted to thank you again for your help and your patience.

• Tecra M7 DVD: CD/DVD RAM drive does not work since the installation of Vista

  I did a clean install on my new Vista Ready M7. He had XP tablet in a first time, and the DVD player worked fine. In fact I used to install Vista (Home Premium).

  Now it doesn't work at all. It runs but does not read. Device Manager tells me impossible to start the device. Tried to update driver and he told me that he has the most uptodate pilot.

  Downloaded all the drivers from the Download Center of Tosh for upgrade of Vista of M7 (who got bluetooth, rotation etc. function properly the screen). But none of the downloads seems to be a driver for the DVD - Ram drive. He cannot find a driver anywhere else (including the Panasonic site).
  DVD player is Mat * a DVD - RAM UJ - 841 s

  Any suggestions?

  Hello

  On the Toshiba driver page, you can find the DLA for Tecra m7.
  Have you tried to install the XP driver DVD-RAM since the Toshiba page on the Vista operating system?

  Maybe it'll market

  But listening the CD/DVD drive uses the current Microsoft drivers that are included in Vista or XP.
  This is why an additional driver should not be necessary!

  An additional proposal;
  Remove the drive from the Device Manager CD/DVD and restart the laptop.
  After restarting again the OS should reinstall the drive and renew the software.

  Another tip:
  -Launch the registry
  -Choose the registry key;
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
  -In the right pane, click UpperFilters and LowerFilters, and then click on remove.
  -Reboot the laptop

• Installation of Win7 on Satellite A210-128 using carpet * a DVD-RAM UJ-850

  Hello

  I have a question about the installation of different OS Vista provided with Toshiba Satellite A210-128.

  I Mat * a DVD - RAM UJ-850 drive and it will not read the CD bootable XP.
  I found a few posts in other forums that this drive won't allow me to install XP.

  So here's my question: someone at - he tried to install Windows 7 (RC TE) with this drive? Or maybe someone has been successful with the installation of Windows XP?

  Thanks to all those who would like to help :-)

  Hi mate

  I think you're a little confused, but I want to help you.
  First of all it s any CD/DVD drive is installed in your laptop.
  The installation of Windows XP and Win 7 should work with all readers who are able to read the CD or DVD.

  I guess that you were not able to install Win XP because the CD/DVD drive was not able to manage this particular drive.
  A friend of mine had the same problem with the other player. After a long period of use of the window of disc was not readable.
  But he could solve this problem. It has burned (copied) the Win XP disk on another CD and then used the second drive to install Win XP.
  The reader to read the other disk correctly.

  Win XP and Win 7 are released on different disk but in most cases the readers should not have any problems with this disc
  But if so, then it s mostly a problem of CD/DVD disc

  See you soon

• DVD player stopped working after the installation of 12 items

  First, I loaded the disc DVD in the drive and tried several times to install 12 elements.  Whenever the program has been installed the computer would start flashing and the dvd drive may stop working. Every time I had to use a PIN to eject the DVD because it would not eject.  It worked well before its installation to 12 items. After that the program was finally installed dvd player worked.  But the program would be closed when you use it too often.  I finally just deleted the program of 12 items on my computer and install it on another system.  It's been a while since the abolition of the program from my computer. Tonight, I reinstalled the program Adobe 12 elements with the dvd drive works fine.  Trying to install the program, all loaded fine.  Then once more, the dvd drive eject nor does any work.  What happened several times with 12 elements of loading on my computer.  It is a real pain.  Now the DVD drive doesn't work, or eject.  Can someone help me out here?  It sucks. The other computer works fine.  It is a HP Pavilion, Windows 7 Home Premium system.

  Computer was off all night. Turned on this morning and the system works now.  I rebooted the system, at least six times last night with no result. I don't know what was different this morning, but everything seems to work.  So if it's not broken I will not try to fix it.  Thanks for posting. Dan

• Equium L350 - Vista fails to start after the installation of recovery

  Hello world

  I have an Equium L350 after an accident I couldn't restart my pc. I tried to solve by using the recovery f8 menu and it did not work so I contacted Toshiba and got a restore disc. I reinstalled from the disc, after the instalation it said complete installation but visa does not start.
  I get: Windows cannot repair this computer automatically click finished to turn off your pc

  After a format and reinstall my computer broken? He is 13 months here for out of warranty

  Hello

  Normally after the installation of recovery your laptop should work fine again.

  In my opinion, it could be a malfunction of the equipment. Did you test the HARD drive for bad sectors? You can do this with Drive Fitness Test: http://www.hitachigst.com/hdd/support/download.htm#DFT
  Download the ISO image and burn it to a disk. Then you can boot from it and test your HARD drive for errors.

  I also recommend to check the RAM for errors: http://memtest86.com/
  Memtest is a good diagnostic tool for the RAM.

  I hope I could help a bit. :)