After reinstalled Realtek HD Audio driver cannot turn on the stereo mix and the digital (HDMI) Audio option

Similar Questions

• lack of audio after reinstalling windows on hp m370n cannot automatically load the drivers what should I do?

  I got a new hard drive and reinstalled Windows XP, but I have no audio. What should I do?

  I checked the Device Manager and miss me all devices marked in 'other devices '. I tried to let the search for system for the driver but he can't find it and I don't have the installation CD.
  Where should I look for the driver?
  I'm missing
  Multimedia controller
  Multimedia video controller
  Network controller
  USB device.

  My computer runs Windows XP and its a HP M370n.

  Any suggestions?

  Hello:

  First install the chipset driver and restart:

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12454&prodSeriesId=316720&prodNameId=316722&swEnvOID=1093&swLang=13&mode=2&taskId=135&swItem=PSG_I20521-104339

  Then, install the video driver and restart.

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12454&prodSeriesId=316720&prodNameId=316722&swEnvOID=1093&swLang=13&mode=2&taskId=135&swItem=PSG_I23037-107909

  See if the audio Realtek XP driver works:

  Accept the agreement, download and install the a 6th on the list.

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=23&PFID=23&level=4&Conn=3&DownTypeID=3&GETDOWN=false

  Your network driver is 6th on the list.

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=14&PFID=6&level=5&Conn=4&DownTypeID=3&GETDOWN=false

  Paul

• After installing Vista, CD/DVD drive cannot be seen or read.

  After installing Vista, CD/DVD drive cannot be seen or read.

  Hi heartmanmd,

  You get the error message?

   

  Run the fixit available in the article below and check if that makes a difference

  
  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista

  http://support.Microsoft.com/kb/929461

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows
  http://support.Microsoft.com/kb/322756/

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  ---------------------------------------------------------------------------------------------------------
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Cannot turn on the center of the action of the taskbar icon

  original title: cannot turn on the center of the action

  My icon of the center of the Action in the taskbar is disable and I want to activate it but when I try to activate it in Control Panel > appearance and personalization > customize the icons in the taskbar, and then I'll turn system icons on or off option to enable it, but the arrow thing It is gray and I can't change it to enable it. Help, please. Sorry for my bad English.

  Rafael

  Lets move forward and try to do an Inplace upgrade and see what it does for you.

  An upgrade on the spot is the final solution before you have to reinstall the operating system.
  Note that it takes as much time to do the upgrade as to reinstall the operating system. In addition, some of your custom Windows settings may be lost through this process.

  How to perform a repair installation of Windows Vista, Windows Server 2008, Windows 7 or Windows Server 2008 R2. Run a repair installation will restore the current installation of Windows to the version of the installation DVD. It also requires the installation of all the updates that are not included on the installation DVD.

  Note Run a repair installation will not damage files and applications that are currently installed on your computer.

  To perform a repair installation of Windows Vista, Windows Server 2008, Windows 7 or Windows Server 2008 R2, follow these steps:

  1. close all running applications.

  2. Insert the Windows Vista, Windows Server 2008, Windows 7 or Windows Server 2008 R2 DVD into the DVD drive of the computer.

  3. in the settings window, click install now.

  Note If Windows does not automatically detect the DVD, follow these steps:

  Click on start and type Drive: \setup.exe in the box to start the search.

  Note The placeholder drive is the drive letter of the computer's DVD.

  List programs, click Setup.exe.

  In the settings window, click install now.

  1. click on connect to get the latest updates for installation (recommended).

  2. type the CD key if you are prompted to do so.

  3. Select the operating system in the "Windows Installer" page you want to update or Inplace.

  4. click Yes to accept the Microsoft software license agreement.

  5. on the which type of installation you want? of the screen, click upgrade.

  6. when the installation is complete, restart your computer.

  Please see: How to perform an upgrade in Place on Windows Vista, Windows 7, Windows Server 2008 and Windows Server 2008 R2

• Help, please! I plugged a new plan "creative cloud membership (one year)", but cannot turn off the "Plan of creative photography of Cloud (one year).

  Help, please! I plugged a new plan "creative cloud membership (one year)", but cannot turn off the "Plan of creative photography of Cloud (one year). What to do?

  Hello

  You can try the steps on the following link to cancel, cancel your membership Adobe Creative Cloud

  If it does not you or if you get an error contact Adobe to contact customer service

• I have Adobe photoshop Elements 4 and use windows 10. When you try to import photos and do other things in Adobe I the following error coming. {Microsoft} [ODBC Access driver} cannot open database' the may not be a database of your application]

  I have Adobe photoshop Elements 4 and use windows 10. When you try to import photos and do other things in Adobe I the following error coming. {Microsoft} [ODBC Access driver} cannot open database' the may not be a database that your application recognizes, or the file may be corrupt,.] Everything worked very well this fault has just come. Anyone know how to solve this problem.

  Settle into the Photoshop Elements forum.

• I turned on my PC today and I did not "PRINT" option when I go to the drop down "FILE" menu... totally gone... Could someone please advise me how to recover?

  I turned on my PC today and I did not "PRINT" option when I go to the drop down "FILE" menu... totally gone... Could someone please advise me how to recover?

  Thank you for your comments... I guess it is the restoration of the system for me!

• HP Envy Phoenix 850-150QE: Reinstall Realtek HD Audio Manager

  Got a new HP computer. Accidentally deleted the SD Realtek Audio Manager. How can I reinstall it?

  Hello

  Try reinstalling your software Realtek HD Audio using Recovery Manager - how to use Recovery Manager to reinstall the drivers and the software is detailed in the document at the link below.

  Recovery Manager - Windows 10.

  Kind regards

  DP - K

• CS6 Design and Web Premium Adobe can't activate after reinstalling desktop PC hard drive crashed.

  I tried to reinstall and activate my copy of Adobe CS6 after my desktop PC hard drive crashed. I wasn't able to disable this copy from the hard drive crashed making even the impossible windows startup. Please tell us how can I activate this copy on my desktop PC.

  Serial number and activation support (non - CC)

  http://helpx.Adobe.com/x-productkb/global/Service1.html ( http://adobe.ly/1aYjbSC )

• Sound seems to be decreasing after that I have used headphones, or turned down the volume.

  I have a HP G62 and he had a GOOD volume, but after that I have to use headphones or turn down the volume, he seems to do something for the volume and when I want to play sound after headphones are disabled you can hardly hear it.
  I turned the volume up on top of everything I can find, but it is so weak, it is not worth listening to!

  Hello

  1. What is the operating system installed on the computer?

  2. were there any changes (hardware or software) to the computer before the show?

  Perform the steps in the article, and check whether the problem is resolved or not.

  No sound in Windows (Windows 7)

  Note: this also applies to Windows Vista and Windows XP

  Hope that helps.

• cannot turn on the firewall in windows vista

  I went to the control panel to turn on the firewall, but a screen will appear that says: "due to a problem not identified, windows cannot display the firewall settings."  When I click on parameter update now a screen said, "firewall Windows was unable to make the requested updates".  Any ideas on how to proceed from here?

  Hello

  You can run this fix:
  Diagnose and automatically fix problems of Windows Firewall service
  http://support.Microsoft.com/mats/windows_firewall_diagnostic/

• Wireless dead after reinstalling Windows. Device Manager can't see the map

  Hello

  I have a laptop model Lenovo 3000 N200 14W 0687.  It was teeming with virus so I wiped the hard drive and installed Windows XP Home Edition from scratch.  Now Device Manager can't see the wireless adapter and Wireless does not work.  I tried to download and install the Wireless driver on the Lenovo site (I don't have a disc of relocation); but I got errors.  Anyone know what could cause this and a fix?

  If you are interested, here are the details of what happened when I tried to download and install the drivers:

  Device Manager gives me the adapters three following network:
  Network adapter 1394
  Broadcom NetLink (TM) Fast Ethernet
  MAC bridge Miniport

  None of which resemble wireless cards. So I used the link http://consumersupport.lenovo.com/ot/en/DriversDownLoads/Drivers.htmlto try out. Enter my serial number L3X3516 took me to a support page client lenovo that says

  Total 13 drivers need to be repaired/upgraded, 9 drivers in need of repair, please click the "Download" button to begin to repair

  One of them was this:

  Intel (r) PRO/Wireless 3945ABG Network Connection

  I downloaded it and it says: 'the contents of this file cannot be unpacked. the executable file that you are trying to run has been damaged. You can get another copy of the file, verify its integrity, and then try again"

  So I used google to find this site:

  http://www.getpcmemory.com/drivers/download-Lenovo-3000-N200-type-0769-notebook-Windows-XP-Vista-DRI...

  who told me that my computer is a Lenovo 3000 n200 Type 0687.

  Using google once again, I found this page:

  http://www-307.IBM.com/PC/support/site.WSS/document.do?lndocid=MIGR-68011

  which was another version of the driver. So I downloaded and unpacked it. I then took a glance at the .txt guide provided with the driver. It is said:

  1. Start Windows XP and log on with administrative privileges.
  

  2. Double-click the driver package to extract it to your hard drive.
  

     The default location is C:\SWTOOLS\DRIVERS\WLLANINT
  

  3. Click Start, then click Run...
  

  4. Specify SETUP.EXE with the full path name where you extracted the
  

     package in step 2, and click OK.
  

     Example: C:\SWTOOLS\DRIVERS\WLLANINT\SETUP.EXE
  

  5. Follow the instructions on the screen to complete the installation.
  
  Unfortunately, there is no setup.exe file in the folder so this has failed.
  
  Regards,
  
  satherb
  

  configuration > wireless lan support > enabled

  for display drivers, re - install it: http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-67978

  and on Device Manager, please, provide the device id. (eg PCI VEN_8086 & dev_2929 & subsys)

  or if you know which wireless adapter you have, download drivers from the download page, then re - install.

• Cannot turn on the firewall of windows 7

  I just got a new Dell computer. For some reason, I can't turn on windows firewall 7. The option is not grayed out, but when I click on 'recommended use of parameters' nothing happens. I did a full scan with Windows Security Essentials and there is no virus.

  Hello
   
  To resolve this problem, you will need to follow these methods provided below.
   
  Method 1: Please run "services.msc", "Event controller Windows" stop first and then make sure that "Base filtering engine" service is started.
  On the Start Menu, type devmgmt.msc, and then open Device Manager. On the view tab, select "Devices by connection" and put a check next to "Show hidden devices". Search for the Windows Firewall authorization driver (there will be a gear icon gold). Double-click on that and on the driver tab, make sure that the startup type is set to "Application".
  Then start the service "Windows Firewall" and see if the problem is resolved.
   
  Method 2: The driver of the authorization (mdsdrv.sys) firewall is a system protected Windows file. You can run the tool File Checker system and if the file is found to be damaged, it will be replaced.
  Proceed with caution.
  Go to start / all programs / accessories.
  Right-click on the element "Command Prompt" and select the "Run as Administrator" option.
  Click on 'Continue' in the UAC prompt.
  In the command window, type the following command.
   SFC/SCANNOW
  Press ENTER.
   
  This will take a few minutes to complete. Try not to use the computer during execution of SFC.
  When the tool is finished, restart the computer and review the firewall options.
  Let me know the results.

  Also follow the Microsoft Windows Help article below.

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  Thank you, and in what concerns:

  I. Suuresh Kumar-Microsoft Support.

  Visit our Microsoft answers feedback Forumand let us know what you think.

• Cannot turn off the LEDS on Cisco Aironet 1141

  I am trying to turn off the LED on a Cisco Aironet 1141 p/n AIR-AP1141N-A-K9.  It is a standalone AP and the CLI I publish this command:

  turn off the display of #led AP (config)

  The light does not go out after you type this command.  If I "run" it appears in the config so that the order has been accepted.  Is there another way to turn off the LED?  I'm under JA1 IOS Version 12.4 (21a).

  If you have the AP 1141 under warranty, you can send an email to [email protected] / * / PA serial number and they can post you the picture ask you.

  You want to say "Thank you"?
  Ne. Just note the useful responses,
  It is more useful than 'thank you'.

• Cannot turn off the keyboard

  After pressing the power button on my PalmZ22 and the disabled keyboard appears and I type to disable the keyboard this screen disappears.  Tapping to turn off the screen to put my password does not work. I tried to reset my Palm with Soft and Hard Reset function, and always with let me not disable the keyboard.

  ecwmoore2106, please do not double - post.